Used Corner Connector Press for sale (16,591)

Condition: good (used), Year of construction: 1978, Make: HAULICK ROOS Type: RVD 40 Year: 1978 Levelling straightner RASTER 12 180/19.150-1 Isdpfxsx S H Ils Addeht New 1986 incl. Decoiler  incl. Feeder  Capacity Kg: 40000 Table Length:590mm Table Width: 500mm Hole in table:100mm Ram size: 590 x 380mm Stroke: 8 - 50mm Strokes: 30 - 300Min.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Iodpfx Adex A U Ncsdsht Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: used, Fensterpresse Ihsdpfxex Svw Ns Addjt Orma Max. 4000x2700mm 380V, 2,2kW - Documentation available: No - CE certificate present: No - Max. workpiece width [mm]: 4000 - Max. workpiece height [mm]: 2700 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: reconditioned (used), Year of construction: 2014, operating hours: 5,612 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total height: 2,800 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), volume flow: 332 m³/h, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,612 hours, stand August 2025 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Ihedevtpq Hjpfx Addjt Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press was partially overhauled and tested in our workshop, see photos and our function video. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: used, Year of construction: 2003, pressure . t throat . mm stroke . mm total power requirement . kW weight of the machine ca. 4 t Ihedpfow Syfcjx Addet

Condition: used, Year of construction: 1960, pressure 1000 t Ihsdpfjw Syd Esx Addst stroke 600 mm weight of the machine ca. 4 t

Condition: used, Year of construction: 1999, stroke 1000 mm diameter of piston 70 mm Iedpfx Aew Sydfjddoht

Condition: new, The AHK M 1230 NC is a highly efficient press brake from KNUTH, designed specifically for sheet metal processing within the press brakes category. This machine offers a modern, cost-effective NC alternative to traditional CNC press brakes, making it ideal for operators accustomed to manual programming. Featuring a high-precision, stress-relieved steel frame and hydraulic cylinders, the AHK M 1230 NC excels in handling complex bending sequences effortlessly. Enhanced safety features, including light curtains and a CE-compliant design, ensure operator protection while maintaining productivity. The NC control system, complete with a user-friendly touchscreen, allows for easy input of bending sequences, accommodating up to 500 programmable data sets. You can confidently handle a variety of materials and shapes thanks to Promecam tool mounts and an adjustable back gauge with motorized X and R axes. With features designed for ease of use and reliability, now is the perfect time to request a quote for the AHK M 1230 NC press brake, ensuring your workshop benefits from superior capabilities in sheet metal processing. Ihodpfx Adsqc S Najdst

Condition: excellent (used), Year of construction: 1995, Decoiler Max. width 350 mm Clamping area coil internal 470 - 530 mm Coil diameter 1500 mm Work load 2000 Kg Straigtner Width 350 mm Roll diameter 30 mm Number off rolls 9 units In feed rolls 2 units In feed roll diameter 90 mm Working speed 40 M/Min Max. thickness 6 mm at 240 N/mm2 Max. Thickness 5 mm at 400 N/mm2 Ihodpfxox Sx Sps Addet Length:3200mm Width:1500mm Height:2200mm Weight:3700kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 2024, condition: excellent (used), Segment radius top tooling for 1000 and 2000 Ton machine Full sets segmented on 835 mm and 10 sections to make 8000 mm Radius 30 / Radius 31 / Radius 32 / Radius 33 / Radius 35 Radius 36 / Radius 39 / Radius 40 / Radius 41 / Radius 42 Radius 43 / Radius 45 / Radius 47 / Radius 48 / Radius 50 Radius 51 /  Radius 53 / Radius 55 / Radius 57 / Radius 58 Radius 60 / Radius 62 /  Radius 70 / Radius 71 / Radius 73 / Radius 75 / Radius 80 Isdpfx Aox Sxuksddsht Length:12000mm Width:2000mm Height:1000mm Weight:15000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2024, Minimum width 65 mm Maximium width 185 mm Load is 200 Metric Ton / Meter Operation angle from 60 - 180 Gr Die length 1000 mm and 500 mm sections Minimale Breite: 65 mm Maximale Breite: 185 mm Belastung: 200 metrische Tonnen / Meter Arbeitswinkel: 60°–180° Iedpfxsx Sw Suj Addjht Matrizenlänge: 1000 mm und 500 mm Segmente Länge: 1200 mm Breite: 1200 mm Höhe: 800 mm Gewicht: 1500 kg Length:1200mm Width:1200mm Height:800mm Weight:1500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Hydraulic press TCS - 150T MACH-ID 8821 Manufacturer: TCS Type: 150T Control system: Siemens SIMATIC OP7 Year of manufacture: 1999 Table load sliding table 20000 Kg Table load upper table 9000 kg Table out feed stroke 2100 mm Column diamater 180 mm Closing force 1500 Kn Opening force 700 Kn Laser safe CE Safety Power 15 kW Ihsdpfx Asulwzmoddot Specifications Metric US Standard Distance between uprights 2000 mm Installation height 2000 mm Table length 1500 x 2000 mm ram stroke 1800 mm Starting speed 50 mm/min. Working speed 8 mm/min. Return speed 50 mm/min. Table rotation 0 - 270 rpm Table rotation 0 - 180 ° Dimensions (estimation) length 4800 mm width 5600 mm height 5200 mm Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: excellent (used), Year of construction: 2017, operating hours: 13,284 h, functionality: fully functional, pressing force: 140 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,500 kg, oil tank capacity: 2,600 l, Technical data baler: Manufacturer Bollegraaf Type HBC 140 Year of construction 2017 Working hours 13,284, as of October 2025 Press power main press 140 tons (max. 153,5 tons) Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm (l x w) Capacity per cycle time 4,34 cbm Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm (w x h), length adjustable Driving motor 2 x 75 kW Connected load 209 kW Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 850 up to 1.500 kg Hydraulicoil 2.600 l Univis N46 Baler dimensions with conveyor built up with hopper approx.13,200 x 24,200 x 7,333 mm (l x w x h) Transport dimensions only baler approx.13,200 x 2,884 x 3,539 mm (l x w x h) Machine weight baler approx. 51,810 tons Technical data feeding and elevating conveyor with gooseneck: Ihjdpfx Adoxpxhvedet Manufacturer Bollegraaf Typ HBT 1216/1800 * 23,300 30°/15° Year of construction 2017 Driving motor 7,5 kW Length feeding conveyor 6,750 mm Length elevating conveyor 14,400 mm Length goose neck 2,150 mm Grade 30° Effecting width 1,754 mm Height of side wall feeding conv. 500 mm Height of side wall elevating conv. 800 mm Transport dimensions feeding conveyor with one segment elevating part 9,816 x 2,500 x 2,242 mm (l x w x h) Transport dimensions elevating conveyor with goose neck 13,472 x 2,800 (without motor) x 2,729 mm (l x w x h) Pit dimensions 10,000 x 3,200 x 1,200 mm (l x w x d) Condition: The press is in very good condition and ready for immediate operation, see the function video for more information. The conveyor belt chain needs replacing. The system will be in operation until December 2025. Scope of delivery: baler with conveyor belt, maintenance platform, access ladder, two wire feed stations for 5 wire reels each (without wire), and bale slider. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2000, operating hours: 28,155 h, functionality: fully functional, Bale Press Paal Konti 200 D, year of manufacture 2000, optional with matching conveyor belt Paal KEM-1400 Technical Specifications: Manufacturer: Paal Model: Paal Konti 200 D Year of manufacture: 2000 Operating hours: 28,155 Pressing force: 60 t Drive power: 45 kW Total connected load: 60 kW Feed opening: 1020 x 1400 mm Bale dimensions: 750 x 1100 mm, variable length Tying: 4-fold automatic Throughput capacity at: 35 kg/m³ approx. 9.5 t/h 60 kg/m³ approx. 16.5 t/h 100 kg/m³ approx. 26 t/h Bale weight: 450 to 650 kg Transport dimensions: approx. 10,123 x 2,152 x 2,720 mm (LxWxH) Machine weight: approx. 15,000 kg Materials: Paper, cardboard, film The press is in good condition and has been inspected and tested. A video is available on our website or YouTube channel. Iodjx Tflfspfx Addsht Full documentation available. Please note: All technical data are based on information from the manufacturer. We assume no liability for the information provided or for any possible errors. The offer is non-binding, subject to prior sale, and may be revoked at any time. Inspections are possible by appointment. Sale is ex works, against advance payment, without warranty or guarantee.

Condition: used, Single-column eccentric press HELMERDING Type EH 25 B Machine No. 5917 Year of manufacture: 1993 Pressing force: 25 tons Throat depth: 180 mm Table area: 560 x 360 mm Ram area: 315 x 150 mm Table through-hole: 150 x 100 mm Stroke adjustment: 8 - 82 mm Ram adjustment travel: 60 mm Installation height max.: 330 mm Clamping pin bore: Ø 40 mm Strokes per minute: 145 Table height adjustment: 150 mm Table height above floor: 630 - 780 mm Motor power: 1.5 kW Power supply: 400 Volt, 50 Hz - Hydraulic clutch-brake combination, manufacturer: ORTLINGHAUS - Electric foot switch and two-hand control - Automatic central lubrication by BEKA lubrication system Ijdpfx Asyath Teddsht - Electrical cabinet with 2-channel contactor control - Press table height-adjustable via 2 threaded spindles - UVV [accident prevention regulations] according to VBG 7n 5.1 for manual loading operations - Electrical diagram Space requirements (L x W x H): 1600 x 1100 x 1900 mm Weight: 2 tons Good condition

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Iedpehlnzkjfx Addoht Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: used, Year of construction: 1984, total length: 3,500 mm, total width: 1,400 mm, total height: 2,500 mm, Weight: 6.800 kg - Year: 1984 - Documentation available: No - CE certificate present: No - Serial number: 12552 - Drive system: Teach-in - Control system brand: Delem - Control system type: DA-22 - Power [kW]: 5.5 - Number of axes [pcs]: 3: Y1+Y2+X - Press force [ton]: 80 - Max. working width [mm]: 3100 - Column gap [mm]: 2500 - Crowning system: None - Punch holder: Standard - Tool holder type: European-style - Tools included: Yes - Options: Digital readout - Motor power: 5.5kW - Transport dimensions: 3500mm x 1400mm x 2500mm (l x w x h) - Transport weight [kg]: 6800kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT Ihsdpjx R S Nrefx Addst VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: ready for operation (used), Year of construction: 2012, Brand: DIXI Model: 60 Sh Year of manufacture: 2012 Pressing force: 60 tons Voltage: 400V Maximum bale weight: 340-500 kg Bale dimensions: approx. 120 x 80 x 80-110 cm Machine weight: 2,400 kg Machine dimensions: 190 cm wide x 140 cm deep x 230 cm high Filling opening dimensions: 115 cm x 80 cm deep x 55 cm high Condition: Very good! Functionality checked. FLITS Rental & Sales service: With every machine, we supply a bundle of binding wire (120 wires). Need more bundles of binding wire? Request a quote with no obligation. FLITS Rental & Sales is your reliable partner for the sale and rental of high-quality machines for both businesses and private individuals. We focus on delivering efficient solutions in the areas of internal transportation, cleaning, waste processing, and working at height. At FLITS Rental & Sales, you will find a wide range of machines suitable for deployment in various sectors. See our advertisements for: waste balers for efficient waste management, electric pallet trucks/stackers for fast and safe internal transport, scrubbers for thorough and professional floor cleaning, forklifts in various designs suitable for different working environments. Ijdpfxox Ux Hxs Addoht With FLITS Rental & Sales, you choose speed, clarity, and reliability. We think along with you, respond immediately, and ensure that you quickly have the right machine at your disposal. Visit our location You are very welcome to view the machines at our premises. We are located at: Schoterlandseweg 94, 8413NE Oudehorne, Netherlands. Visits are possible by appointment, so we can take the time to inform you thoroughly and show you the right machines. Contact Do you have questions or would you like to receive a no-obligation quote? Please feel free to contact us: We are happy to help you further. Waste baler Paper baler Cardboard baler Plastic baler Waste compactor Recycling Textile baler Waste Waste processing DIXI

Condition: good (used), Year of construction: 1987, functionality: fully functional, Clamping unit heating capacity, 1 heating rod / 8 heating rod: 0,48 / 0,9 kW clamping force: 2 x 500 kN heating plate dimensions: 550 x 600 mm piston stroke: 250 mm diameter of piston, main cylinder: 240 mm diameter of piston, locking cylinder. 39 mm locking cylinder: 260 mm Return capacity: 2 x 600 kN Ijdpfx Asyaackeddeht dimensions: 2600 x 2100 x 2100 mm weight approx.: 5 t

Condition: excellent (used), Year of construction: 2006, Dimensin: 2650 x 2100 x 2100 mm Clamping Force: 635 KN Working pressure: 206 bar Piston diameter: Ø200 mm Stroke: 140 mm Daylight: 150/180 mm Heating plant dimension: 250 x 300 mm Max. mass of heating plant: 70 kg Oil reservoir: 100 l Rated power: 19.66 kW Heater capacity: 9.6 kW Vacuum motor power: 2,6 kW Between light curtain and mould area: 270 mm Stroke of vacuum cover: 140 mm Ihodpfx Asyaab Heddot The vulcanizing press from manufacturer PAN STONE, model S-V-65-2RT-PCD, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. The machine was part of a production line responsible for manufacturing high-performance seals used in various industries. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: good (used), Year of construction: 1997, Clamping Unit: Clamping force: 7,000 kN Operating pressure: 250 bar Specific pressing pressure: 610 N/cm² Number of levels: 2 Installation height with 75 mm heating plate & 20 mm insulating plate: approx. 2x 190 mm Piston stroke: approx. 400 mm Piston 1 diameter: 543 mm Clamping force, rapid traverse: approx. 2 x 85 kN Retraction force: approx. 2 x 47 kN Operating pressure: 300 bar Piston 2 diameter: 60/40 mm Stroke: 400 mm Estimated weight: approx. 16 tonnes Isdpfjyaabysx Addoht Hydraulic System: Pressure adjustment: 40 - 300 bar Flow rate regulation: 0 - 99 % Flow rate l/min (HD): 45 against 300 bar Drive power: 22 kW Tank dimensions (LxWxH): 1000 x 770 x 535 mm Closing Speed: Rapid traverse: approx. 40 - 50 mm/s Slow closing: approx. 0 - 20 mm/s Pressing speed: approx. 0 - 3 mm/s Slow opening: approx. 0 - 20 mm/s Opening, rapid traverse: approx. 0 - 60 mm/s

Condition: used, Year of construction: 2005, functionality: fully functional, Clamping force: 4900 kN Working pressure: 206 bar Ihjdpfjyaaa Asx Addet Heating plate dimensions: 700 x 700 mm diameter of piston: 558,8 mm max. stroke: 250 mm daylight: 300 mm max. mass of heating plant: 560 kg capacity of oil tank: 1100 l rated capacity: 82 kW heating capacity: 56 kW enginge output, vacuum motor: 4 kW Stroke of vacuum cover: 200 mm dimensions: 3975 x 2935 x 2555 mmm Equipped with a crane runway (monorail) with three chain hoists Producer: STHAL Year: 2011 Lifting capacity: 3 x 400 kg Lenght of crane runway: ca. 3500 mm Rolling chassis Lifting capacity: 400 kg Lifting height: 3000 mm stroke speed - main stroke: 4 m/min stroke speed - fine stroke: 1 m/min The vulcanizing press from manufacturer PAN STONE, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: ready for operation (used), Year of construction: 1998, This WILD door leaf press line was manufactured in 1998. It is designed for door production, handling dimensions from 1,800 to 2,300 mm in length, 500 to 1,300 mm in width, and thicknesses of 35, 40, and 44 mm. The line includes areas for gluing, pressing, and handling door panels with advanced feeding and transfer systems. If you are looking to get high-quality door production capabilities consider the WILD door leaf press line we have for sale. Contact us for more information. Machine Benefits Technical Machine Benefits • Dimensions for door production: lengths: 1800 - 2300 mm • Dimensions for door production: widths: 500 - 1300 mm • Dimensions for door production: thicknesses: 35 / 40 / 44 mm Extra Information Iedpfx Adjyaqmgsdeht Consisting of the following areas: Endless door panel gluing with frame laying station Press line with hard fiberboard loading station First area consists of: Portal feeding Angle transfer with rip and cross cut saw Feeding and supply of longitudinal and cross frame parts from magazines Longitudinal cross-cut station for the longitudinal frame parts Connecting station for the frame parts with the door leaf core, equipped with clamping devices Conveyor belt angle transfer with shuttle transfer of the door leaf cores to the glued hardboard panels Second area consists of: Feeding of the hardboard panels Brush cleaning machine Hardener application machine from below Glue application machine from below Disk roller conveyor Angle transfer for the lower hard fiber board Vacuum turning device for the upper hard fiberboard Automatic loading station for hardboard panels and door leaf cores Two door presses with two x four pressing stations each, set up parallel to each other Both presses are loaded at the infeed with one shuttle loading basket Both presses are unloaded at the outfeed with one shuttle unloading basket Angular transfer to the infeed into a hedgehog buffer Angular transfer at the outlet of the hedgehog buffer and feeding for stacking One-sided vacuum destacking with protective plate placement Note: The technical data and descriptions are transcribed from the original order confirmation. The information is for reference only and is not legally binding.

Condition: used, Year of construction: 1963, total height: 2,880 mm, total width: 1,500 mm, total length: 2,300 mm, Empty weight: 8.000 kg Price: On request - Year: 1963 - Documentation available: No Ihedpswmfrrefx Addet - CE certificate present: No - Serial number: 12691 - Motor power: 7.5kW - Table width: 650mm - Table length: 950mm - Ram width: 340mm - Ram length: 550mm - Min. stroke: 25mm - Model: Eccentric - Max. stroke: 118mm - Height adjustment: 75mm - Power: 160.0ton - Transport dimensions: 2300mm x 1500mm x 2880mm (l x w x h) - Transport weight [kg]: 8000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1989, total height: 2,750 mm, total width: 1,700 mm, total length: 1,600 mm, Empty weight: 4.000 kg - Year: 1989 - Documentation available: No - CE certificate present: No - Serial number: 4414 - Motor power: 5.5kW - Table width: 560mm - Table length: 800mm - Ram width: 300mm - Ram length: 450mm - Min. stroke: 8mm - Model: Eccentric - Max. stroke: 100mm - Number of columns: 1 Ihodpfx Adsx Dkfpedst - Power: 63.0ton - Transport dimensions: 1600mm x 1700mm x 2750mm (l x w x h) - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum