Used Counter for sale (2,397)

Condition: excellent (used), Cutting mill, side mill, granulator, shredder, plastic shredder, granulate mill, granulator, rotor mill, recycling technology, -Condition: Mill is equipped with a new set of blades, but without a control unit or sieve. -Manufacturer: RAPID, Side-mounted mill cutting mill -Type: 650-M -Drive motor: 37 kW -Number of cutting blades: 10 pieces -Number of counter blades: 2 pieces -Inlet cross-section: 600 x 300 mm -Rotor width: 610 mm -Rotor diameter: 300 mm -Quantity: 1 cutting mill available -Price: per piece -Dimensions: 1385/1200/H2170 mm Ksdpfx Aowg Axvjhzewt -Weight: 1208 kg

Condition: used, Year of construction: 2005, Three knife trimmer Kolbus HD 150.B Year: 2005 Description: Kwjdpfxjvf Dtys Ahzot - Right hand infeed - Automatic hopper feeder for inline production - Cut counter - Exchangeable cutting tables (standard set) - Knife pre-setting device - Set of knife holders: 2 - Sets of knives: 2

Condition: used, functionality: fully functional, Year of construction: 2024, operating hours: 34 h, load capacity: 8,000 kg, lifting height: 3,440 mm, free lift: 1,170 mm, fuel type: diesel, mast type: triplex, construction height: 2,250 mm, fork carriage width: 2,120 mm, fork length: 2,400 mm, empty load weight: 12,500 kg, total length: 4,100 mm, drive type: Diesel, construction width: 2,130 mm, Diesel Forklift Load center of gravity: 600 Fork width: 150 mm Kodpfjv Ihkhox Ahzswt Fork thickness: 70 mm Mast type: Triplex Condition: Ready for use and fully functional Technical condition: New Front tires type: Superelastic Front tires size: 8.25-15 non-marking Rear tires type: Superelastic Rear tires size: 8.25-15 non-marking Description: In addition to this Clark model, we also have approximately 200 heavy-duty forklifts, compact forklifts, forklifts, and sideloaders in our warehouse in Hamburg and Gdansk. Visit our website - sago-online. Hire purchase and financing at favorable conditions are always available. We are also happy to purchase your used vehicle on an over-the-counter basis, even without you purchasing a vehicle from us. Our owner, Mr. Peter Sawitzki, would be happy to advise you in detail about this C80D. P.S.: Our forklift workshop specializes in repairs, maintenance, overhauls, and custom builds for forklifts weighing 8 tons and over. We would also be happy to display your vehicle for consignment sale. Sideshift, fork positioner, Heating, full cab, full free lift, DPF

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, Technical details x-travel 300 mm y-travel 160 mm z-travel 290 mm table surface area 600 x 210 mm tool taper SK 40 spindle turning speed range (16) 40 - 2000 U/min feeds -stepless- 5 - 500 mm/min rapid traverse 1,2 m/min Kwedpfx Ahjyangqszet spindle motor 1,5 / 1,9 kW total power requirement 9,5 kVA weight of the machine ca. 830 kg dimensions of the machine ca. 2000 x 2200 x 1655 mm Additional information The machine is in very good condition and comes from a training workshop. Equipment: * 3-axis positioning control with active digital display Heidenhain TNC 123 - Manual mode: Manual operation and positioning with manual input - Automatic mode: Single-block programme run, programme storage * Fixed angle table * Movable vertical milling head, swivel range +/- 90 degr., quill stroke 60 mm * Coolant equipment * Central lubrication * Tailstock with counter bearing * Manual

Condition: used, Year of construction: 2019, Control: MITSUBISHI M730UM with CELOS Main spindle with integrated motor spindle ISM 80: 15/18.5 kW Speed range: 10–4000 rpm 10" hollow chuck 254mm KITAGAWA BB210A821 Counter spindle with integrated motor spindle ISM 65 Speed range: 10–5000 rpm 10" hollow chuck 254mm KITAGAWA BB208A621 20-position BMT star turret KNOLL high-pressure coolant system 70 bar Ksdpoycukhofx Ahzowt Y-axis with 100mm travel Gantry loading system LG-10AI

Condition: used, Year of construction: 2008, functionality: fully functional, Turning / milling center with counter spindle with 10 CNC axes (X1, X2, Z1, Z2, Y1, Y2, B1, B2, C1, C2) Control: FANUC 31:iA Main Spindle Power: 15/11 kW bar material dia.: 51 mm spindle revolution: 5.000 min-1 Counter Spindle Power: 11/7,5 kW bar material dia.: 51 mm spindle revolution: 5.000 min-1 Ksdpfx Aoycuikshzjwt Turning and milling spindle Power: 7,5/3,7 kW Turning and milling spindle speed: 12.000 min-1 max. rotation length turret bottom: 1.005 mm Slide cross X1 / X2 / Z1 / Z2 / B2: 455 / 222,5 /1.090 / 1.005 / 1.008 mm Slide cross Y1 / Y2: +/- 70 / +20, -50 mm Swivel range B1 axis: +/- 95 ° Linear rack magazine incl. support robot CNC support steady rest Coolant cyclone filter system incl. 2 pcs. coolant pumping spindle oil cooler

Condition: good (used), Year of construction: 2007, operating hours: 88,040 h, functionality: fully functional, machine/vehicle number: 07400003691, turning diameter: 120 mm, spindle bore: 118 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 30 m/min, total height: 2,500 mm, total length: 5,500 mm, total width: 2,500 mm, overall weight: 11,000 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D POWERLINE, DMG GILDEMEISTER TWIN 102 CNC Turning and Milling Center - Recorded spindle hours: 43,558 - Spindle speed range: 3,200/5,000 rpm - Swing diameter: 270 mm - Spindle distance: 900 mm - X1 axis travel: 290 mm - Z1 axis travel: 650 mm - X2 axis travel: 180 mm - Z2 axis travel: 650 mm - Y1 axis travel: ±40 mm - Z3 axis travel: 670 mm - X3 axis travel: 175 mm Kodpfx Asyaqgyohzswt - Max. bar diameter: 100/104 mm - Number of driven tools per tool turret: 12 - Including chip conveyor, with 2 tool turrets (each with 12 tool stations), main and counter spindles, as well as foot switches Attention, the machine has the following defects: - The B-axis is defective (mounted on turret 1) - Guideways and drives show age-related wear - X2 axis (guide rails) runs slightly out of alignment by approximately 0.03 mm (should be re-measured) - Occasionally, axis reference value setting in the control system fails - The hydraulic pump was replaced after a failure and is now installed externally as a standalone unit FCA D-58256 Ennepetal, loaded on truck at a mutually agreed date at the end of February 2026.

Condition: good (used), Year of construction: 2008, operating hours: 72,899 h, functionality: fully functional, machine/vehicle number: 07510001241, turning length: 1,185 mm, turning diameter: 640 mm, spindle speed (max.): 12,000 rpm, workpiece weight (max.): 150 kg, total height: 3,040 mm, total length: 7,800 mm, total width: 4,100 mm, overall weight: 16,500 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D, DMG GILDEMEISTER GMX 250 LINEAR CNC Turning and Milling Center - Recorded spindle hours: 39,361 - Swing diameter: 640 mm - Counter spindle turning diameter: 400 mm - Spindle distance: 1,500 mm - X1 axis travel: 550 mm - Y1 axis travel: 180 mm - Z1 axis travel: 1,185 mm - B1 axis travel: 240° - X2 axis travel: 180 mm - Z2 axis travel: 1,050 mm - Z3 axis travel: 1,150 mm - Spindle speed range: 3,200/4,000 rpm - Rapid traverse rate, Slide 1 (X/Y/Z): 40/24/70 m/min - Rapid traverse rate, Slide 2 (X/Z): 24/36 m/min - Rapid traverse rate, Slide 3 (Z): 36 m/min - Tool holder: HSK 63 - Spindle speed: 12,000 rpm Kwedpsyaqczofx Ahzst - Number of tool stations in chain magazine: 40 stations - Incl. tool holders mounted on the turret - Incl. bar loader, manufacturer: COCCHE GIOVANNI, type: CNC-DB 110, year of manufacture: 2008, serial number: CNCDB-08.306, weight: 1,500 kg Note: The machine has the following defects: - The hydraulic unit is faulty – it needs to be repaired - The Q2 axis (milling spindle tool changer) fails frequently - X2 axis (guideways) moves slightly askew - The linear guides and drives show wear commensurate with age Attention: A vehicle with 3,000 mm transport width is required for transport! FCA D-58256 Ennepetal, loaded onto truck at a mutually agreed date at the end of February 2026.

Condition: used, Year of construction: 1970, diameter / mm Cutting (quantity) / weight / kg Kwjdpfx Ahotnmmbjzot This tailstock comes from the Froriep D1.050x10.000 crankshaft lathe. This is sold individually and can be used for various purposes Can be used, for example as a counter spindle or for other purposes. Center height: 500 mm

Condition: used, Year of construction: 2011, turning length 1500 mm control SINUMERIK 828D centre height 270 mm greates pass round over bed 540 mm swing diameter over slide rest 310 mm bed width 350 mm max. workpiece weight 1500 kg spindle bore 85 mm turning speeds 27 - 2250 U/min main drive DC 11 kW MACHINE EQUIPMENT: - AME chip conveyor - Lynette - Heavy grey cast iron bed for optimum damping and reduced tool wear - Inductively hardened and parallel synchronised bed guides - Counter guides completely Turcite-coated and hand-scraped - Hardened and ground ball screws - Thermosymmetrical headstock Kwedjxyaf Rspfx Ahzst - Main drive 11 kW - Infinitely variable speed range 27-2250 rpm with 3-stage gearbox

Condition: used, functionality: fully functional, Year of construction: 2015, operating hours: 12,654 h, load capacity: 5,000 kg, lifting height: 4,045 mm, free lift: 1,310 mm, fuel type: diesel, mast type: triplex, construction height: 2,200 mm, fork carriage width: 1,350 mm, fork length: 2,350 mm, empty load weight: 6,585 kg, total length: 3,150 mm, drive type: Diesel, construction width: 1,480 mm, Diesel Forklift Load center of gravity: 500 Fork width: 150 mm Fork thickness: 60 mm Mast type: Triplex Condition: Ready for use and fully functional Ksdjwiz I Uspfx Ahzswt Technical condition: Very good Front tires type: Superelastic Front tires size: 355/45-15 Rear tires type: Superelastic Rear tires size: 2.50-15 Description: In addition to this Linde model, we also have approximately 200 heavy-duty forklifts, compact forklifts, forklift trucks, and sideloaders in our warehouses in Hamburg and Gdansk. Visit our website - sago-online. Hire purchase and financing at favorable conditions are always available. We are also happy to purchase your used vehicle over the counter, even without you purchasing a vehicle from us. Our owner, Mr. Peter Sawitzki, will be happy to advise you in detail about this H50D-02. P.S.: Our forklift workshop specializes in repairs, maintenance, overhauls, and custom builds for forklifts weighing 8 tons and over. We're happy to display your vehicle for consignment sale. Sideshift, Full free lift,

Condition: good (used), Year of construction: 2020, functionality: fully functional, working width: 1,350 mm, Wide belt sanding machine for woodworking Manufacturer: Viet, Model: SV3-4.3 RVXR Year of manufacture: 2020 Technical Data Manufacturer: Viet Italia S.r.l. Model: SV3-4.3 RVXR Year: 2020 Belt width: 1350 mm Maximum working height: 160 mm Machine with adjustable head (fixed working height of 900 mm) Feed speed: 1.1 kW (1.5 HP) Speed: 0.5–7 m/min Calibration sanding unit, sanding drum diameter: 190 mm Belt length: 2620 mm Dimensions: approx. W 2.2 x D 3.5 x H 2.5 m (+ dust extraction) Weight: 6.5 t (+ dust extraction) Features – Machine with movable head – Sanding belt change on the left side – Tool set – Digital thickness display – Material too strong at the infeed – Electropneumatic oscillation control – Air filter with condensate separator and automatic drain – Maintenance-free pneumatic system – Pneumatic lifting and lowering when switching sanding units on or off – Machine with head adjustment (fixed working height 900 mm) – Lifting system on 4 columns (spindle) with chain drive – Table extension front and rear, each with 1 roller – Industry 4.0 (LAN) package with LAN network connection – Centessimal lifting system with inverter – Electromechanical grit set – Belt speed adjustable via frequency inverter – V-Spin unit with 15-disc sanding system / diameter 80 mm The V-Spin unit consists of 15 disc brushes arranged in line and moving in opposite directions. The combination of both movements makes the V-Spin unit suitable for rounding sharp edges and removing slag or oxides. – 16 support plates for V-Spin unit, diameter 80 mm Scotch-Brite + abrasive, grit 80 – 16 support plates for V-Spin unit, diameter 80 mm Tampico + grit 80 – X-Spin unit / sanding system with 15 discs, diameter 123 mm Group consists of 5 rotary heads, each fitted with 3 rotating sanding brush pads, each diameter 123 mm – Oscillating Scotch-Brite brush – Linear cleaning systems – Conveyor belt Conveyor made of HYPALON rubber, heat and oil resistant, hardness 60 SH, smooth surface – Belt cleaning blower for the transport belt incl. extraction – IPC MONITOR 15" touch-screen control for machine operation, up to a maximum of 10 processing units – 2 Euro pallets filled with new sanding belts – Technical documentation including operating manual The control system manages the following processes: - Start sequence of selected drive motors - Storage of up to 1000 processing programs - Automatic positioning of thickness control - Acoustic and visual notifications at machine startup - Operating hours counter - Automatic control of feed speed depending on processing capacity (indicated in sqm). This functionality enables increased sanding belt lifetime through the use of statistics. Ksdpeya Eyhefx Ahzowt Extraction Unit - Manufacturer: Ringler, Kärcher Group - Model: RE 36/110 D11 IE3 - Output: 11.0 kW - 2930 rpm - Connection: 400 V / 19.54 A / 50 Hz - Year: Dec 2018 - Weight: 754 kg All information without guarantee. A demonstration is possible anytime in our showroom.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Ksdpfxjx Dnb Us Ahzewt Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see our video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: like new (used), Year of construction: 2020, functionality: fully functional, machine/vehicle number: 483, Casemaker, Automatic production of book cases, files, display cards, calendar backs, game boards or luxury packaging. Co-Pilot with touchscreen, Automatic case counter, Board magazine for manual loading, Centre strip infeed (flexible), Waste chopper, Cloth feeder, Glue unit, Preheated glue tube, Viscosity control, Device for inside lining with hotmelt, Device for producing padded cases, Pressing station, Tacking delivery. Kwedpox Ryr Iofx Ahzjt

Condition: used, Year of construction: 2013, Robotic system consisting of: 1 welding robot Qirox QRH 390 incl. control unit, programming hand device, 24 V buffering, PC-side computer interface, 2 GB flash drive Gas nozzle sensor, arc seam tracking, point editor, Qineo Puls 450 with Premium control module, wire feeder, torch hose package, welding torch, torch testing gauge, mechanical cleaning, pressure booster, Floor-mounted track 10 kN, travel length 8 m, robot installed in upright position on base pedestal. Wire drum travels with the system. 4 positioners with counter bearing WP-TC 10 kN, load capacity 1,000 kg, clamping length 3.0 m, rotation radius 1 m Connection control, 4 light barriers, 4 prestart selectors, Delivery: immediately available. Special price for purchase by 15.12.2025! System will be cleaned, tested, and serviced prior to dismantling. Kwodpfx Ahox Atp Iozot Warranty: functional guarantee Very low operating hours

Condition: excellent (used), Konica Minolta Bizhub 2250p with small counter ( 7 million / engine ) Kwjdsl Ux Dmspfx Ahzot The machine is in perfect condition , tested by our technicians , ready to print !! High Speed : 250 ppm ! Equipment : - PF 703 ( X2 ) - RU 510 ( X2 ) - LS 506 - FD 503 - RU 509 - TD 501 - FS 532 As an experienced retailer of used copiers, we have developed a real expertise in packing and pallet shipping, to guarantee our customers machines in perfect condition upon receipt. We ship copiers coming from, and maintained by Konica Minolta France. If you have any questions don't hesitate to ask me Our company offers the largest range of Konica Minolta production copiers, and handle world-wide deliveries on request. Please do not hesitate to contact us for further information.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Vecoplan Shredder, Type VAZ 110, year of manufacture 2017, with hopper and extraction port. Manufacturer: Vecoplan Type: VAZ 110 Year of manufacture: 2017 Motor rated power: 18.5 kW Frequency inverter rated power: 22 kW Feed opening: 1200 x 1075 mm Rotor diameter: 250 mm Rotor length: 1075 mm Kodsx Uz Raspfx Ahzswt Rotor speed: 90-250 rpm Number of cutting tools: 27 Throughput: 2 cbm/h Screen hole size: 20 mm Extraction port diameter: 200 mm Dimensions: approx. 2355 x 1590 x 980 mm (LxWxH) Weight: approx. 1800 kg Accessories: Spare parts package with 20 mm screen, 1 set of tools, cutters and counter cutters, motor, plastics, springs, etc. Materials: Wood waste, films, packaging material, chipboard, paper, textiles Remarks: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video on our website or YouTube channel. Complete documentation including CE declaration is available. Inspections can be arranged at any time by appointment. On request, we are also happy to carry out test runs with your material for a handling fee. If you have any questions about the machine, we are available by phone Monday to Thursday from 08:00 to 14:00 h and Friday from 08:00 to 13:00 h. Please note: All technical data is based on manufacturer information. We do not accept liability for the information provided or any possible errors. All offers are subject to change, prior sale, and revocation at any time. Inspections can be arranged upon request. Sale is ex location, without warranty or guarantee.

Condition: used, Year of construction: 2011, functionality: fully functional, Shredder Höcker PHSS 40/110 Technical data: Manufacturer: Höcker Polytechnik Model: PHSS 40/110 Year of manufacture: 2011 Drive power: 22 kW Working width: 1100 mm Rotor diameter: 400 mm Cutting principle: High-speed shredder shaft with counter comb Kwjdpex Uz Npsfx Ahzet Remarks: The machine is in fully functional condition. It has been inspected and tested at our facility in 28816 Stuhr. A video is available on our website or YouTube channel. Viewings can be arranged at any time by appointment. Upon request, we are also happy to carry out test runs with your own material for a handling fee. If you have any questions about the machine, we are happy to assist you by phone from Monday to Thursday, 08:00 to 14:00, and on Friday from 08:00 to 13:00. Please note: All technical data are based on information provided by the manufacturer. We do not accept liability for the accuracy of this information or for any possible errors. Offers are subject to change, prior sale, and revocation at any time. Inspections are possible by arrangement. The sale is ex location, without warranty or guarantee.

Condition: good (used), Year of construction: 2014, operating hours: 7,145 h, functionality: fully functional, Baler Presto HPK 50 HS, Year of Manufacture 2014 Manufacturer: Presto Model: HPK 50 HS Year of Manufacture: 2014 Drive: 30 kW Pressing Force: 50 t Operating Hours: 7145 Filling Opening: 1600 x 650 mm (L x W) Channel Cross Section: 700 x 950 mm Maximum Filling Volume: 1.06 m³ Cycle Time: 20 s Tying: 4-fold Throughput Capacity at 35 kg/m³: 5.5 t/h 60 kg/m³: 8.8 t/h 100 kg/m³: 12.7 t/h Bale Weight: up to 500 kg Machine Dimensions: 8420 x 1900 x 2400 mm (L x W x H) Machine Weight: approx. 10,500 kg Materials: Paper, Cardboard, Film, PET Bottles Remarks: Blades and counter-blades as well as all sliding plastics have been replaced. The baler is in good condition and has been inspected and tested. A video is available on our website or YouTube channel. Operating manuals and CE declaration are available. Kjdpox Uzzxjfx Ahzewt Inspections, including under power, are possible by appointment at any time. Upon request, we also conduct tests with your material for a handling fee. We are happy to answer any questions about the machine by phone from Monday to Thursday from 08:00 to 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data is based on manufacturer’s specifications. We assume no liability for the information provided or for any potential errors. The offer is non-binding and subject to prior sale and revocation at any time. Viewings are possible by arrangement. Sale is ex works against advance payment, without warranty or guarantee.

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Technical details max. wheel diameter 2-45 mm gear width 250 mm max. module 1,5 mm min. module 0,5 mm Control Fanuc 18i-MB weight of the machine ca. 2,2 t dimensions of the machine ca. 2100 x 1440 x 1700 m Additional information The combined CNC gear hobbing and worm milling machine KOEPFER MZ 120 is characterized by its flexible usability and is used in the small module area. Just by swiveling the milling spindle from the horizontal to the vertical position and selecting the corresponding operating mode of the CNC control, the worm milling machine becomes a gear hobbing machine and vice versa. CNC control Fanuc 18i-MB (Dialog/ISO) CNC axes = X-axis plunge axis Z-axis longitudinal axis C-axis workpiece spindle B-axis tool spindle V-axis loader axis longitudinal A-axis swivel axis tool spindle head (included as an option) Y-axis shift axis (included as an option) With the following production programs: Worm milling Hobbing Worm hobbing Bevel gear and spur gear milling Bevel gear hobbing Milling cycles = straight, oblique, crowned toothing, radial, radial-axial, co- and counter-rotating milling, roughing, finishing, worm gears, straight-toothed bevel gears, face gearing (option only in the partial process) Worms [Equipment] Coolant tank 300 liters KF with LNS Turbo MS 250 Chip conveyor, built in 2021!!! Kraft and Bauer fire extinguishing system Spiral conveyor Machine documentation [Technical data] Workpieces: Workpiece diameter 2-45 mm Max. workpiece length 250 mm Tooth length 150 mm Max. module in steel= 1 mm (gear hobbing) Kwodsx Ux Suepfx Ahzet 1.5 mm (worm milling) 0.5 mm (bevel gear hobbing) Tools: Cutter diameter= 16-32 mm (gear hobbing) 40-63 mm (worm milling) Machine: Max. setting angle of milling head= +/- 45° (gear hobbing) +/- 30° (worm milling) Shift travel= 34 mm (manual adjustment) 34 mm (CNC axis) Collet/retraction mandrel W 20 Max. speed of workpiece spindle 770 rpm. Milling spindle drive 0.55 kW Max. milling spindle speed 8000 rpm Axis drives = X-axis (plunging) / travel 80 mm via CNC Z-axis (longitudinal feed) / travel 190 mm via CNC C-axis (workpiece axis) via CNC Rapid traverse = X-axis 6000 mm/min. Z-axis 6000 mm/min. Hydraulic unit 0.37 kW

Condition: used, Counter bearing Make Cover Rail inside 92 mm outside 130 mm Kodpfx Ahsctd Rhozowt

Condition: used, In this offer you purchase a used booklet making system ‘Plockmatic PBM500’ Object of sale: 1 x Plockmatic PBM500 with the following equipment: incl. trimmer module Counter readings: Total: Approx. 767,015 booklets Condition: This offer is a used device, which may show signs of use (minor scratches or yellowing). (minor scratches or yellowing). The device has been tested for function Packaging and dispatch: You are welcome to view the device during our business hours. Please make an appointment for this! Kedpfoudv T Rsx Ahzjwt Seaworthy packaging and worldwide shipping available on request! A function test will be recorded on video for you before dispatch or collection. For further information, you can of course also contact us personally.

Condition: used, functionality: fully functional, In this offer you purchase a used booklet making system ‘Plockmatic PBM350’ Object of sale: 1 x Plockmatic PBM350 with the following equipment: incl. PBM-TR front trimmer incl. SquareFold Not the right equipment? It is no problem to configure the machine according to your wishes. Feel free to contact us! We also have the right production printing system in stock Kwsdpfevy Aabex Ahzst Counter readings: Total: Approx. 85,000 brochures Condition: This offer is a used device, which may show signs of use (minor scratches or yellowing). (minor scratches or yellowing). The device has been tested for function A test printout can be seen in the photo Packaging and dispatch: You are welcome to view the device during our business hours. Please make an appointment for this! Seaworthy packaging and worldwide shipping available on request! A function test will be recorded on video for you before dispatch or collection. For further information, you can of course also contact us personally.

Condition: like new (used), Year of construction: 2006, spindle motor power: 15 W, travel distance X-axis: 177 mm, travel distance Y-axis: 41 mm, travel distance Z-axis: 550 mm, rotational speed (min.): 5,000 rpm, total height: 2,065 mm, total length: 4,390 mm, total width: 1,741 mm, overall weight: 5,000 kg, CNC controller: Nakamura-Tome FANUC Capacity X-axis travel mm: 177,5 Y-axis travel mm: ± 41 Z-axis travel mm: 550 B-axis travel mm: 689 C-axis: 360º (0,001º) Turning length mm: 500 Max. turning diameter mm: ø: 190 Distance between spindle centers mm: 780 Bar work capacity mm: 51 Upper turret Tool holder: VDI-30 Number of tool slots St .: 12 Kwsdsx Dbxgjpfx Ahzjt Speed driven tools RPM: 3.600 Drive power driven tools kW: 5.5 / 3.7 Main spindle Speed spindle rpm: 5.000 Drive power spindle kW: 15 / 11 Maximun torque Nm: 47,2 Counter spindle Speed spindle rpm: 5.000 Drive power spindle kW: 11 Equipment Chip conveyor Part catcher Bar Loader RBK 10016 Milling function Working time hours Potencial nominal kVA: 31,43 Basic machine dimensions / weight Length mm: 4.390 Width mm: 1.741 Height mm: 2.065 Weight kg: 5.000

Year of construction: 2022, operating hours: 503 h, condition: used, Serial number: 32228478-00520-0xxxx Please contact ATS Norway for more information Please provide reference number upon request: 20427 Specifications: - 2022 model - 503 hours - Lifting capacity of 150 kg - Aggregate - Vacuum - 8.5 kW - Forks - Rubber tracks - Ready for delivery Kwodpfx Aowi Rkrehzet Description: We have a 2022 150 DA silent xl Vacuum lifter for stone slabs for sale. The machine works as it should and only has 503 hours on the counter. Efficient vacuum lifter that makes the job much easier for the gardener who will carry out the job. Ready for delivery Hours: 503 Own weight: 1689 Kw: 8.5 Model: 150 DA silent xl Vakuumløfter til steinheller. SE VIDEO