Used Cross Carriage for sale (6,277)

Condition: used, Year of construction: 2009, conveyor belt, belt conveyor, transport belt, belt conveyor Lrodpotrhm Aefx Aazet -Manufacturer: Grenzebach, conveyor belt 2 levels type EZT with guide rollers -Speed: frequency controlled -Drive: 2x SEW Eurodrive -Conveyor belt length: 1400 mm -Belt spacing: 410 mm -Cross carriage: roller spacing 1000 mm -Number: 2x conveyor belt available -Price per piece -Dimensions: 1450/1550/H920 mm -Weight: 358 kg/pc.

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. Ljdpezp H R Esfx Aazjrt This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: used, Hardinge HLV-H High Speed Super Precision Tool Room Lathe Max’ Distance Between Centres 18” Max’ Swing over Bed 11” Max’ Swing Over Carriage 9” Max’ Swing over Cross Slide 6” Spindle Capacity: Though Spindle - 1 1/4” 5C Round Collets - 1 1/16” 5C Hex Collets - 7/8 5C Square Collets - 3/4” With Step Chucks – 1 1/16” to 6” With Jaw Chuck (Through Spindle) - 1 5/32” With Expanding Collets 3” Variable Spindle Speeds - 125 to 3000 rev/min Ljdoy Nfqmjpfx Aazort Tailstock M/T 2 3 Phase Electrics Net Weight (approx.) 750Kgs Supplied with: 2 Axis Digital Readout 4 Jaw Chuck Faceplate 3 off Multifix Tool Holders Set of Misc’ 5C Collets For Sale Jet Machinery Ltd Jet Machinery Stock No: #79017 Machine Serial Number: HLV-H14793T Cost: £8,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: good (used), Year of construction: 2016, 2016 Tornos DT 26 Swiss Type CNC Sliding Head Lathe With Fanuc Series 31i-Model B Control & Tornos SBF326-3.2M Bar Feeder Lrjdpfxoz Dg Eve Aazet Maximum Bar Ø25.4mm. Rapid Traverse 32m/min. Standard Workpiece Length With Guide Bush 225mm. Standard Workpiece Length Bushless 50mm. Main Spindle- Spindle Speed Range 0-10,000rpm (10.5kW Motor). Maximum Turning Tools 6 (Shank 12 x 12mm.). Number Of Frontal Tools (Main-Operation/Counter-Operation) 4/4. Max Front Drilling Ø12mm, Max Front Tapping M10 x 1.5.Cross Drilling/Milling Tools 6 (ER20), Max Rotating Tool Speed 6,000rpm (1kW Motor), Max Front Drilling Rotating Tools Ø10/Ø10mm, Max Front Tapping Rotating Tools M5 x 0.8. Counter Spindle-Maximum Bar Ø25.4mm. Main Spindle- Spindle Speed Range 0-15,000rpm (5kW Motor). Max Insertion Length Of Workpiece Into Counter Spindle 100mm. Max Standard Length Of Workpiece 120mm. Max Back Drilling Ø10mm, Max Back Tapping M6 x 1. Cross Drilling/Milling Tools 6 (ER20), Max Rotating Tool Speed 6,000rpm (1kW Motor), Max Front Drilling Rotating Tools Ø10/Ø10mm, Max Front Tapping Rotating Tools M5 x 0.8. Counter-Operation-Max Number Of Tool Positions 8, Max Rotating Tool Speed 7,200rpm (1kW Motor). S/No. 2581050017 (2016). Please note a loading charge of £200 + VAT to be added to buyer's invoice. With Coolant System, Hennig Chip Conveyor, Krauft Bauer Fire Suppressor Unit, SEI Mist Extraction Unit, Parts Catcher, Parts Conveyor, Signal Tower, Tool Kit, Cromar Swarf Bin & Manuals. Overall Dimensions L2,230 x W1,250 x H1,730mm. Weight 2,400kg.

Condition: excellent (used), Year of construction: 2021, machine/vehicle number: 21-06-12-054, functionality: fully functional, operating hours: 385 h, actuation type: electric, Equipment: CE marking, saw blade guard, scorer, Available from April 1, 2027, for self-disassembly and self-collection. The machine features ProDrive control with a 3.5" color display and a separate keyboard. The height and swivel adjustment of the saw unit are motor-driven. The CNC-controlled parallel fence enables a cutting width of 1,300 mm. Equipment / technical data: • Machine height 910 mm • Control panel at eye level • ProDrive control with 3.5" color display • Main motor 5.5 kW (7.5 hp) VARIO • Stepless speed control, approx. 2,000–6,000 rpm • Saw unit that can be swiveled to one side, 0–46° • Extended cutting height for saw blade diameters up to 500 mm • AKE quick-change system for the main saw blade • 2-axis scoring unit • Motorized height and lateral adjustment of the scoring unit • Scoring unit motor 0.75 kW / 8,200 rpm • LED lighting in the area of the scoring unit • Table extension 840 mm • Double roller carriage 3,800 mm with floor support • On/off switch on the double roller carriage • Angle miter fence, length stop up to 3,500 mm • Two individual folding stops • Extendable cross slide extension, extendable to 650 mm • CNC parallel fence, cutting width 1,300 mm • Travel speed of the parallel fence 250 mm/s • Automatic dimension correction depending on the fence profile • Front support roller, 300 mm wide • DUPLEX 1350 mm double-sided miter fence Ljdjz Ah E Repfx Aazsrt • Template holder directly on the control panel • 99 storable cutting programs • Operating hour counter • USB interface • 400 V / 50 Hz Special equipment: 3,800-mm double roller carriage, CNC parallel fence 1,300 mm, 2-axis scoring unit, VARIO drive, and the DUPLEX miter fence. Inspection and test run possible by appointment.

Condition: used, Year of construction: 2015, Cutting and machining center, FTB 100 A2 2S3 NFZ Feed direction from right to left Windows 10 min. cutting length (PVC only): 296 mm min. part length (PVC with steel): 300 mm max. part length (PVC with steel): 4,000 mm max. profile depth: 130 mm max. profile height: 130 mm Automatic feeder magazine for manual loading, for 12 profiles with a min. length of 600 mm and a max. length of 6,500 mm: 8 axes - CNC - machining station A2 - 3 CNC axes X, Y, Z - one 2-way spindle each, 0.75 kW 2 S 3 – Sawing station - 1x stepless swivel range of the saw from 45° - 135° - Saw motor 2.2 kW + 3,000 rpm - Saw blade Ø 550 mm - 1x saw 45° - Saw motor 2.2 kW + 3,000 rpm - Saw blade Ø 550 mm CNC - 3 axes – Milling station for end machining of profiles: - with automatic tool changer for 16 tools Cross conveyor with buffer function CNC - 3 axes – Milling station for end machining of profiles: - with automatic tool changer for 16 tools TFT screen for steel length display - 12" TFT screen for displaying the steel lengths for manual steel insertion and insertion depth. Label thermal printer PF4i with LAN - with network connection for manual application of labels Laser e-SolarMark 30W - CO2 laser, 30 W power - 230V 50Hz / 115V 60Hz, 1PH, 700W ASE 100 S steel cutting and insertion Lrodezm Hr Repfx Aazet - with feeder magazine with 12 slots Control panel steel profile loading ASE 100 - 15-inch TFT display touchscreen Double screw unit from above and below - automatic distance adjustment between the two screw units, motorized, screw spacing: min 155 mm / max. 500 mm Double dowel hole drilling station Ø 6mm and Ø 10 mm - with automatic adjustment to different profile types with 8 lateral positioning points 3-axis - CNC - machining station S, type L - one 3-axis tool carrier (twin module) for up to 18 machining units, equipped on both sides One locking component insertion station for a standard locking component for frame profiles - with vibrating hopper, bunker and locking component singulation - positioning for attaching the locking components Locking component insertion station via bar magazine - One locking component insertion station for a locking component for frame profiles and mullions/transoms, on one side. 2x screw unit for locking component inserter - automatic single screw unit for locking component insertion stations, positionable in the y-axis Cross conveyor magazine - for transporting the profiles for stacking Stacking and sorting unit, 3 axes - one stacking and sorting unit in a 3-axis design Carriage change station - one carriage change station for positioning two carrier carriages in the profile stacking position. Plant capacity: approx. 270 frame units in 7.5 hours with 85% availability approx. 130 mullions, posts, uprights with the following machining operations: Frame approx. 1200 x 1200 mm: 4 x cutting 2 drainage slots, rebate bottom 2 drainage slots outside/bottom 2 ventilation slots, rebate top Screws 4x/part 6-8 x standard locking component insertion for window 8 x sealing groove milling 2-3 x dowel holes vertical bars for window

Condition: excellent (used), Year of construction: 2010, Capacity Swing over bed 750mm / 29.5" Swing over carriage 480mm / 18.9" Max. Turning diameter 750mm / 29.5" Max. Turning length 3935mm / 155" Distance between centres 4000mm / 157.5" Max. load between centres 3000kg Max. load by chucking 750kg Spindle Spindle speeds 3-1000rpm spindle speed range manual 2 steps Spindle nose type A2-11 Spindle bore 6.9mm / 6.9" Spindle taper MT6 Carriage Max travel X axis 425mm / 16.7" Max travel Z axis 3935mm / 155" Rapid traverse X axis 3m/min / 120ipm Rapid traverse Z axis 6m/min / 236ipm Ball screw (diameter x pitch) X axis 32 x 5 mm Z axis 50 x 10mm Cross side width 260mm / 10.2" Turret tool post Curvic type H-4 (Manual) Number of tool positions 4 Tool site 32 x 32mm (1.25 x 1.25") Tailstock Taper in tailstock spindle MT6 Ledpfx Ajzfac Tsazert Tailstock quill stroke 200mm / 7.9" Tailstock quill diameter 112mm / 4.4" Motor Main spindle motor AC18.5/15kw (25/20HP) X axis servo motor AC1.0 kW (1.3HP) Z axis servo motor AC2.9KW (3.8HP) Lubricant pump motor for headstock 0.2kW coolant pump motor 0.18kW Lubricant pump motor for apron 0.025kW

Condition: used, Robust cross-conveyor for round timber For sale is an extremely robust cross-conveyor for logs, taken from a professional sawmill operation. Features: Heavy-duty industrial design Double chain conveyor Short conveying distance Fast and reliable transport of round timber to the log carriage Solid and durable steel construction Immediately available Lodpfx Aaozq T Adezjrt The system is in good, functional condition and can be inspected under power by appointment. Please submit a fair and realistic offer.

Condition: like new (used), Year of construction: 2021, FMT Tarnów LZ 400S – 2021 – 1000 mm – excellent condition For sale: FMT Tarnów LZ 400S universal lathe, manufactured in 2021. The machine has been used very little and is in very good technical and visual condition. It features a modern, robust design from the Polish manufacturer, Fabryka Maszyn Tarnów. Lsdez D T T Hepfx Aazort The lathe is equipped with an ISKRA NP-20T-V digital position readout, a cooling system, and a quick-change tool clamping system with additional toolholders. The machine is ready for operation. TECHNICAL DATA Working parameters: * Center distance: 1000 mm * Swing over bed/cross slide: 390 mm * Swing over carriage: 225 mm * Bed width (upper part): 260 mm * Maximum workpiece weight in centers: 200 kg * Coolant tank capacity: 20 l Headstock: * Spindle nose: DIN 55027-6 (PN-C6) * Spindle bore: 62 mm * Spindle internal taper: DIN 228 ME70 * Spindle speed range: 30–3000 rpm * Main drive motor power: 7.5 kW Tailstock: * Quill travel: 110 mm * Quill diameter: 60 mm * Quill taper: Morse 4 Feeds: * Longitudinal feed range: 0.025–2.0 mm/rev * Cross feed range: 0.012–1.0 mm/rev Threads: * Metric threads: 0.2–14.0 mm * Whitworth threads: 80–1.5 tpi * Module threads: 0.1–7.0 * Diametral Pitch threads: 200–3.5 EQUIPMENT * ISKRA NP-20T-V digital position readout * 3-jaw chuck * Quick-change tool post * Several additional quick-change toolholders * Tailstock * Drill chuck for tailstock * Cooling system * Additional jaws and accessories as shown in the pictures * Work area lighting * Documentation DIMENSIONS AND WEIGHT * Length: 2100 mm * Width: 1080 mm * Height: 1520 mm * Weight: 1800 kg * Power supply: 400 V * Total installed power: 9 kW Manufacturer: Fabryka Maszyn Tarnów (FMT) Model: LZ 400S Year of manufacture: 2021 Turning length: 1000 mm Serial number: 40S213438 The machine is in very good condition and shows only minor signs of use.

Condition: used, Year of construction: 2006, functionality: fully functional, Equipment: rotational speed infinitely variable, Manufacturer: 600 Lathes Model: Harrison V350 Centre Height: 170 mm Swing over Bed: 350 mm Swing over Cross Slide: 196 mm Swing in Gap: 535 mm Width in front of Face Plate: 165 mm Distance between Centres: 650 mm Spindle Speeds (stepless via potentiometer across 3 ranges, with digital readout): 15 - 340 rpm 45 - 1010 rpm 150 - 3250 rpm Spindle Mount (Camlock): D1-4 Spindle Bore: 54 mm Spindle Motor: 7.5 kW Carriage Guideway Width: 318 mm Cross Slide Travel: 250 mm Top Slide Travel: 140 mm Tailstock Quill Travel: 140 mm Tailstock Quill Taper: MT4 Quill Diameter: 63 mm Metric Version Machine Threads: Metric: 0.2 - 14 mm (51) Imperial TPI: 2 - 56 (56) Module: 0.2 - 3.5 (20) Diametral Pitch: 8 - 56 (20) Drive Power: 7.5 kW Equipment: 3-Axis Digital Readout 3-jaw Chuck Röhm D:200 mm 4-jaw Chuck D:160 mm Collet Chuck System Steady Rest 4-position Quick Change Toolpost Live Centre Chuck Guard Additional Chip Shield on Carriage Lrjdpfjxcuuljx Aazjt Coolant System Rear Splash Guard Machine Documentation incl. Schematics Dimensions: Floor to Spindle Centre: 1050 mm Overall Length: 1900 mm Overall Width: 1100 mm Overall Height: 1300 mm Weight: 1350 kg The machine can be demonstrated under power on site by arrangement. All details without guarantee. Errors and prior sale reserved.

Year of construction: 2025, operating hours: 1 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: SFERA21Kommission1, Stretch winder ATLANTA SFERA Easy 6 programs can be saved individually Winding height 2150mm Mast height 2050 mm (fits through almost every door) Foil specification Max. outer diameter Ø300mm - height = 500mm - core Ø76mm GMK (compass) The start and end of the winding is always identical Manual line formation Tension of the film can be saved in 4 steps TECHNICAL DETAILS: two maintenance-free AGM batteries 12 V - 100 Ah connected in series 160 pallets per charge - charging time: 8 -10 hours High frequency battery charger with LED indicator Wrapping height “machine with MAST (pallet included) 2,150 mm Height query via light button or by entering dimensions on the display Protective bar for emergency stop of the travel drive Emergency stop switch according to CE regulations Acoustic warning signal and warning light when the machine starts Fall protection for the film slide Push button for start & stop Function of the machine according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL: All function parameters can be set via the display F00 - Screen lock program change F02 - Adjustable machine speed around the pallet up to 80 m/min Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F13 - F16 - Foil application tension foot & head wrapping / ascent & descent independently adjustable F17 - F20 - Foil pre-stretching foot & head wrapping / ascent & descent independently adjustable F62 - Ergonomic height for film change Lredpfsz Dvi Rjx Aazst Display foil consumption (option for PRS - PS) ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL: 6 storable wrapping programs for SFERA EASY F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F10 - F11 - Wrap cycle with preset start and stop height F12 - Winding to a stored height (switching off the light button for the height) F21 - Wrapping cycle for large pallets F22 / F23 - Winding cycle for cover sheet film F29 - Soft start cycle for edge protection application F30 - F31 - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges

Condition: good (used), functionality: fully functional, Subject to differential taxation according to §25a of the German VAT Act. You will receive a regular invoice. Internal article number: 26057 Lathe Weiler Matador + Multifix "A" baseplate + 3-jaw chuck + Collets + Coolant pump Center height approx. 150mm Turning diameter over carriage 160mm Turning diameter over bed approx. 300mm Distance between centers approx. 500mm Ljdpfszx R R Iox Aazjrt Spindle bore approx. 36mm Speed range 30 - 3500 rpm Automatic longitudinal/cross feeds Tailstock MK3 Dimensions (L x W x H): 150 x 70 x 150cm Weight: 600kg The machine comes from an educational institution and is in good condition. You are welcome to inspect the machine while it is powered on, in our heated storage area of over 500 m².

Condition: ready for operation (used), Year of construction: 2012, L & Z Spindle Lathe ZMM - CU 630 RD incl. Digital Display -CE marking -Digital display Ledezhx Hvjpfx Aazsrt -Year of manufacture 2012 -Center height 315mm -Turning diameter over guides 630mm -Turning diameter over cross slide 430mm -Distance between centers 1500mm -Turning diameter with bridge removed 830mm -Spindle bore 103mm -Automatic longitudinal / facing feeds -Motorized rapid traverse in the carriage -Speed range 16 - 1250 RPM (stepless speed control) -Drive power 11Kw -Three-jaw chuck / ROTAX 315 incl. hard & soft jaws -Chuck guard -Tailstock -Steady rest -Multifix base with inserts -Coolant system -Work light Dimensions: L x W x H 3.5 x 1.5 x 1.7 meters / Weight 4000Kg Errors and omissions excepted.

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery Ljdjfv Hphepfx Aazert PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: used, Fork carriage with hydraulic side shift + long forks, suitable for STILL model EFG 3.0/6004 Technical data: Lredpfx Aajztvuzozet - Fork carriage width: 1,100 mm - Fork length: 1,900 mm - Fork cross-section: 100 x 45 mm

Condition: ready for operation (used), L & Z lathe WEILER MATATOR incl. Heidenhain digital display ND 780 -Center height approx. 150mm -Swinging diameter over carriage approx. 160mm -Swinging diameter over bed approx. 300mm -Distance between centers approx. 500mm -Three-axis digital display / Heidenhain -Collets / quick-change tool holder & various collets -Chuck guard -Chip guard -Multifix base plate & inserts -Spindle bore 36mm -Speed range 30 - 3500 rpm -Automatic longitudinal / cross feeds -Tailstock MK 3 -Three-jaw chuck -Documentation Dimensions: L x W x H 1.6 x 0.7 x 1.6 meters / Weight 600 kg Errors and omissions excepted. Ljdpfxezpba Uj Aazort

Condition: excellent (used), Catalog number 7382 TECHNICAL DATA Tenoning carriage: - Electric feed with stepless speed adjustment - Carriage adjustable at an angle - Feed motor: 0.46 kW - Table size (L/W): 700x450mm, extendable to 1150mm - Cross fence on carriage – cutting length on extendable telescope: 1860mm - Rotary block in the fence - 2 pneumatic clamps Crosscut saw: - Max blade diameter: 380mm - Max cutting height: 110mm - Blade adjustable up/down, forward/backward, and at an angle - Blade guard - Saw motor: 2.2 kW Tenoning spindle: - Pneumatic spindle stroke - Spindle up/down and stroke adjustment via handwheels - Max tool diameter: 320mm - Spindle diameter: 40mm - Working spindle height: 220mm - Spindle lock - Motor: 7.5 kW Profiling spindle: - Pneumatic spindle stroke - Spindle up/down and stroke adjustment via handwheels - Max tool diameter: 200mm - Working spindle height: 220mm - Spindle diameter: 54mm - Spindle lock - Extendable table support - Motor: 7.5 kW Glazing bead saw: - Max blade diameter: 200mm - Blade bore: 30mm - Blade adjustable forward/backward, up/down - Blade guard - Motor: 2.2 kW Feed unit: - Number of rollers: 8 pcs - Motor approx. 0.55 kW - Roller size: 110x50mm - 8 feed speeds: 4, 6, 8, 10, 12, 15, 20, 30 m/min - Extraction port diameters: 60mm, 2x130mm, 110mm, 100mm - Operating pressure: 6-8 bar - Dimensions (L/W/H): 3600x2100x1600mm, weight approx. 2500kg FEATURES – For window production – Pneumatic spindle stroke – Carriage with electric feed – Crosscut saw – Tenoning spindle – Not repainted, used machine, in very good condition Ljdpfx Aszr Nb Soazjrt Net price: 27,900 PLN Net price: 6,640 EUR (based on the exchange rate of 4.2 PLN/EUR) (Prices may change with significant currency fluctuations)

Condition: like new (used), Year of construction: 2022, operating hours: 100 h, The log processing line includes the following units: • log splitting band saw – ELCA SNV14 • log handling carriage – ELCA CMOL33 • planer – ELCA PTL1000 • cross-cutting circular saw – ELCA TRCBT3 • multiple-blade rip saw – COSTA LEONE 2160 • log profiling system – VISION_1200 • material handling systems required for servicing the processing line ◦ cross conveyor chain conveyor ◦ roller conveyor • band saw sharpening machine – ALIX AF 518 Lrjdpfx Aajzg Dl Iszst • dust and chip extraction system – VENTIL VENETA, model PF/JET, designed specifically for the system

Condition: new, Year of construction: 2025, functionality: fully functional, power: 7 kW (9.52 HP), input voltage: 400 V, type of input current: three-phase, cutting height (max.): 120 mm, saw blade diameter: 400 mm, tilt adjustment saw blade: 45 °, height adjustment type: electric, actuation type: electric, Equipment: CE marking, saw blade guard, scorer, Efficient and precise cutting with high ease of operation thanks to the electromotive adjustment of the main saw blade (height/angle) and the parallel fence. Powerful motor, speed up to 5,000 rpm, scoring saw speed up to 8,000 rpm. Double roller carriage, the heart of the panel saw, smooth-running and durable. Cutting length max. 3,200 mm Safe operation thanks to proven safety devices. Equipment: Machine frame: Torsionally rigid and self-supporting guarantees the necessary smooth running and stability Control: PLC control Electromotive height adjustment and tilt 0-45° for the main and scoring saw blade via push and hold button. Saw unit: Powerful motors for excellent cutting performance Drive power/speed of the main saw spindle with automatic brake Main saw motor 7 kW, speed adjustment by switching over the drive belt, speeds 5,000 / 4,000 / 3,000 rpm Speed of the scoring saw 8,000 rpm Quick-change system for the main saw blade Saw blade angle is displayed numerically Double roller carriage: Linear, round guide rails ensure a precise and durable system with high-quality cutting results and a long service life Small rollers inside the carriage guarantee smooth sliding during cutting incl. upper carriage locking Carriage length 3,200 mm Parallel fence: max. width 1,250 mm with electromotive adjustment removable fence High-quality work table made of robust sheet steel guarantees high rigidity Safety zone starts approx. 200 mm in front of the saw blade Crosscut fence: Cross position of the panel is displayed numerically with telescopic device for cuts up to 3,100 mm and 90° guarantee Robust, gap-free flap units are easy to move Fence ruler is removable Cutting to length on the crosscut fence on the sliding carriage 3 digital displays with fine adjustment for high repeatability Display up to max. 3,200 mm Extraction: to prevent flying chips and dust protects the operator from hazards Table extension and table widening Design: Clamping shoe, sliding stick, sliding and return handle Lrsdpsz Dwftsfx Aazot Miter stop for manual mounting on the sliding carriage Technical data: Main saw: Saw blade diameter 400 mm, speed 3,000/4,000/5,000 rpm, motor 7 kW S1 Scoring saw: Saw blade diameter 120 mm, speed 8,000 rpm, motor 0.75 kW S1 Saw blade tilt 0-45° Max. cutting depth at 45°: 85 mm Max. cutting depth at 90°: 125 mm Parallel fence: max. 1,250 mm Sliding carriage: 3,200 x 418 mm Max. cutting capacity: 3,200 mm Height adjustment: electromotive Angle adjustment: electromotive Table size: 1,020 (690+720) mm Extraction: Diameter 100 mm Space requirement: 6,700 x 3,900 x 1,890 mm CE marking in accordance with EU directives including documentation and maintenance instructions Saw blades are not included in the scope of delivery.

Condition: refurbished (used), Year of construction: 1975, functionality: fully functional, CANALI Vertical Automatic High-Performance Block Bandsaw Model BBS.V "PACIFIC" K/L-B-P 1800, Type 555, Year of Manufacture 1975 with control panel in the cabin, bandsaw wheels Ø 1800 mm, bandsaw wheel width 280 mm, max. saw blade width 310 mm, bandsaw blade length 11,500 mm bandsaw size 11495x310x1.85x55 log infeed system approx. 20 m long, four-strand system with inserter block carriage with ejector onto block cross conveyor CANALI pneumatic clamping carriage, Type 501.09 with 4 clamping jaws, 3 log turners, 4 ejectors, drive power 100 kW, carriage speed 5-120 m/min. Lrodpoxvrnijfx Aazet powered roller conveyor with slab removal with brush, lifting device with puller for trimming complete electrical switchgear cabinets complete sharpening room equipment for bandsaw blades

Condition: excellent (used), Conventional lead and feed screw lathe from manufacturer Nardini S.A. Máquinas e Ferramentas, model ND 220 SE. Well-maintained machine in technically flawless condition. Technical Data: Machine type: Lead and feed screw lathe Manufacturer: Nardini Model: ND 220 SE Control: Conventional Center height: 220 mm Distance between centers: 1,000 / 1,500 mm Swing over bed: 440 mm Swing over cross slide: 270 mm Swing in gap: 630 mm Gap length in front of faceplate: 200 mm Spindle Spindle nose with short taper size 6, DIN 55027 Spindle bore: 52 mm Internal taper: 1:20 Reducer bush: MT 4 18 spindle speeds: 25 – 2,000 rpm Feed and thread range 132 longitudinal feeds: 0.057 – 2.645 mm/rev 132 cross feeds: 0.028 – 1.322 mm/rev 54 metric threads 54 Whitworth threads 54 module threads 54 diametral pitch threads Leadscrew pitch: 6 mm Carriage & Compound Cross slide travel: 250 mm Top slide travel: 125 mm Max turning tool section: 20 × 20 mm Top slide swivel range: ± 45° Tailstock Quill diameter: 60 mm Internal taper: MT 4 Quill stroke: 200 mm Lateral offset: 15 mm Drive Main motor: 3-phase 380 V / 50 Hz, pole-reversible, 3 / 6 kW Coolant pump: 0.09 kW Operational Advantages - Robust machine bed - Very large feed and thread range - Suitable for both single-part and series production - Easy operation Lrjdpfx Aoypcpxoazjt - Durable industrial quality Used machine Technically tested Fully functional Ready for immediate use Delivery time: Immediate Ex-works, loaded free of charge Loading: Forklift available Transport / shipping: can be arranged

Year of construction: 2002, condition: used, - Manufacturer: Elmag Superfici - Type: TT1-30 - With cross carriage wheels - Length: 3,000 mm - Working width: 1,350 mm Lsdpfxex Url Uo Aazjrt - Total width: 1,660 mm - Working height: 900 + - 20 mm - Height adjustable - Location, in stock - Volts, Hz 400 / 50 - Motor power 0.75 kW

Condition: used, functionality: fully functional, Year of construction: 2001, operating hours: 18,875 h, load capacity: 4,500 kg, lifting height: 4,300 mm, fuel type: diesel, mast type: simplex, construction height: 2,950 mm, fork carriage width: 1,350 mm, fork length: 1,100 mm, empty load weight: 6,500 kg, total length: 3,000 mm, drive type: Diesel, construction width: 1,500 mm, Diesel forklift Load center: 500 Fork width: 120 mm Fork thickness: 50 mm ISO class: ISO class 3 = 2,500 - 4,999 kg Mast type: Standard Transmission: Hydrostatic Condition: Ready for use and fully functional Technical condition: good Front tire type: Superelastic Front tire size: 355/65-15 Front tire condition: 20 - 40% Rear tire type: Superelastic Rear tire size: 250-15 Rear tire condition: 80 - 100% Description: Half cab, work lights front and rear, 3rd and 4th valve to fork carriage, 1x cross lever, 2x single lever, two-pedal system Side shifter, Integrated side shifter 3rd valve, 4th valve, work light rear, work light front, half cab, load backrest, dust filter, interior mirror, windshield wiper, LED, seat Lsdpfxezllz Ij Aazert

Condition: good (used), Maximum turning diameter with top carriage 1350 mm Maximum turning diameter with side carriage 1100 mm Maximum turning height 1000 to 1250 mm Table diameter 1100 mm Maximum table load 4000 kg Power of main motor 30 kW Table speeds 6.3 - 200 rpm Number of table speeds 16 Distance between floor and table surface 955 mm TOP CART: Vertical travel of the ram with tool holder (Z axis) 600 mm Longitudinal travel of the slide (X axis) 700 mm Number of tool holes in the tool holder 5 Diameter of tool hole 60 mm Working feeds 12; 0,21 - 10 mm/min Fast feed rate 1880 mm/min SIDE CARRIER: Vertical slide travel (R axis) 800 mm Slide travel (P axis) 630 mm CROSS BEAM: Vertical travel 1000 mm Lrsdpjtn S D Asfx Aazst Feed rate 500 mm/min

Condition: like new (used), functionality: fully functional, Year of construction: 2022, load capacity: 1,400 kg, working height: 8,860 mm, operating hours: 350 h, Equipment: documentation/manual, STILL FM – X 14. Reach Truck – 2 pcs. Forklift For sale: Reach trucks, condition like new, only 350 engine hours, year of manufacture 2022. Serviced exclusively by STILL. Detailed description see photo. • Quantity: The offer is for 2 units of STILL FM – X 14 forklifts. • Batteries: Attention, 2 batteries are included for each forklift (4 batteries in total) – ideal for multi-shift operations! • Hydraulic telescopic forks extendable from 80 cm to 120 cm!! • Load capacity: 1400 kg Price: €15,900 Top condition, serviced exclusively at STILL !!! Ljdpfx Aouvdbujazert For sale: Reach Truck – condition like new, only 350 engine hours, year of manufacture 2022. Serviced exclusively by STILL.STILL FM – X 14. Reach Truck. x 2 pcs.Load capacity: 1400 kgPrice: €15,900Attention: The price includes 2 batteries, making it suitable for multi-shift operations!Detailed Description:Hydraulic telescopic forks: extendable from 80 cm to 120 cm!!Vehicle width: 1,302 mmLoad wheel tires: Diameter 285 mm, polyurethaneDrive wheel tire: Diameter 360 mm, polyurethaneBattery change: Side battery replacement via changeover rack, battery also transportable by craneMast functions: Hydraulic mast reach cross-shift +/- 50 mm, with mast tilt, including necessary hydraulics (4 functions)Fork carriage: Type A, 4 rollers, width of fork carriage: top 840 mm, bottom 755 mmOverall height: 3,300 mmFree lift (H2): 2,740 mmRated lift: 8,300 mmMaximum height (h4): 8,860 mmLoad capacity at maximum lift: 1,350 kgLift height sensor: LED height sensor – preparation for innovative lift height measurement using an LED light beam for precise measurement of optional assistance functionsForks: 1150 x 100 x 40 mm, 2A, LSP 600Hydraulic system: Central position of fork tilt/mast and sideshift selectable via buttonsTilt angle: 0.5/2 degrees forward/backward mast tiltTransport: Mast disassembled before shipping for easier transportOverhead guard: Driver's overhead guard with head paddingOverhead guard dimensions (short version): Overall height: 2200 mm, depth: 645 mmAdditional roof equipment: Overhead guard pillar for mounting MMS terminals or similar auxiliary equipmentInterior rearview mirror: Panoramic mirror on the drive side mounted on the overhead guard for improved visibility when driving out of rack aislesDisplay: Remaining battery charge indicator integrated into the displayDriver's seat: Hydraulically suspended comfort driver's seat MSG 65 with fabric coverSeat adjustments: Infinitely variable weight adjustment, backrest tilt, longitudinal adjustment, and lumbar supportHydraulic control: Joystick 4Plus (central control element combines lift, tilt, and auxiliary hydraulic functions, including horn)Drive activation: Designed as a foot and seat switch combined with single-pedal control and travel direction change via rocker switchSteering: Fully electric 360° steering, height-adjustable steering wheelIgnition switch: Start/Stop buttonAdditional electrical equipment: For external systems (data terminal and scanner) consisting of:Assistance system: Infinitely variable speed reduction depending on the steering angle (CSC - curve speed control)Warning device: STILL SafetyLight 4PLUS with 4 LEDs and a moving light spot in the direction of travel to show the vehicle's approach directionFleet Manager 4.0: Online fleet management via WEB application (GPRS - SIM card, access via employee cards, data, reports, ...)Number of batteries included: 2 pcs !!!!!Battery specifications: 48 V / 4PzS 620 Ah