Used Turn Cross for sale (11,584)

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Pedszp H R Eopfx Ac Hjgr Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: good (used), Year of construction: 2016, FOR SALE CNC Lathe TOP TURN S20C – Year 2016 Pgjdpfx Acoy Sltto Hsr Brand: TOP TURN (Distributed by major machine tool networks) Model: S20C Year: 2016 CNC Control: FAGOR (User-friendly interface for teaching cycles and ISO programming) Technical Description This 2016 CNC lathe is a versatile machine, ideal for precision work in small to medium production batches. Its modern design offers excellent rigidity and very quick set-up, thanks to the Fagor control system. Capacity: - Swing over bed: 400 mm - Swing over carriage: 210 mm - Distance between centers: 1,000 mm - Bed width: 300 mm Spindle: - Spindle bore: 52 mm (Comfortable bar capacity) - Spindle speed: Up to 2,500 rpm - Spindle nose: Camlock D1-6 Included Equipment - FAGOR CNC: Color screen, cycle-assisted programming (ideal for operators used to conventional machines) - Turret: Automatic turret (electric/hydraulic) for fast and programmable tool changes - Chuck: Precision 3-jaw chuck (approx. 200 mm diameter) - Tailstock: CM4, robust - Safety: Fully enclosed machine with interlocked sliding doors, compliant with CE standards - Coolant system: Centralized with integrated chip tray Highlights - Recent (2016): Modern electronic and mechanical components, easy to source spare parts - Precision: High-precision ball screws on both axes - Compact: Small footprint relative to its machining capacity Weight and Dimensions - Dimensions: Approx. 2,400 x 1,400 x 1,700 mm - Weight: Approx. 1,800 kg

Condition: good (used), Year of construction: 2006, Machine used only for plastic. Technical details shown in attached pdf document. Pedpfx Aju Ibihoc Hogr Parts shown by hand not come.

Year of construction: 1981, condition: good (used), Spindle motor for CNC lathe MAZAK SLAT TURN 30, year of manufacture 1981. Podpfx Aexr Dhyec Hjgr

Condition: like new (used), Range (depending on lighting conditions): up to 15 m Range with laser receiver: 30 m and more Leveling accuracy at 5 m: +/- 1 mm Pgjdpod Ecncsfx Ac Hsr Self-leveling range: 4° +- 0.5° Accuracy of the horizontal line at 5 m: +- 1.5 mm Accuracy of the vertical line at 3 m: +- 0.75 mm Number of laser lines: 2 Weight: 485 g

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Psdpsfv Hphsfx Ac Hogr Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, controller model: Siemens 840 D, table diameter: 1,220 mm, TECHNICAL DETAILS Table diameter: 1,220 mm Max. turning diameter: 1,500 mm Max. height under the cross beam: 900/1,200 mm Saddle travel, X-axis: 1,000 mm Table speed range: 4.5 to 100 RPM Psdpjzuy Eaofx Ac Hogr Feed rate range: 0.127 to 6.35 mm/rev Tool changer: 30 positions MACHINE DETAILS Control system: Siemens 840 D Main drive motor: 41 kW EQUIPMENT 8 clamping jaws 30 tool holders Full enclosure Mist extraction system

Condition: ready for operation (used), Year of construction: 2008, operating hours: 411 h, functionality: fully functional, chuck outer diameter: 1,200 mm, spindle speed (max.): 300 rpm, spindle speed (min.): 2 rpm, turning diameter: 1,600 mm, Massa Heavy Duty Precision CNC Vertical Borer Model: VL-1200 ATC + C Control: Fanuc 18i TB Year: 2008 Max Swing Dia:1600mm Max Turning Dia: 1350mm Max Turning Height: 1250mm Pgodpfxjzv T A Io Ac Hor 4 Jaw Scroll Chuck Dia: 1200mm Table Speeds: 2-300 RPM 16 Station Tool Changer ‘C’ Axis 360 Degrees ‘C’ Axis Milling Spindle BT 50 Dimensions: 6300 x 4500 x 5800mm Weight: 33,000 KGS

Condition: excellent (used), Year of construction: 2017, 2017 RoboJob Turn-Assist-E Robotic Automated Robotic Loading System With Fanuc M-10iA/12 (A05B-1224-B202) Robot & Robot Controller Pgodpfxozvnn Se Ac Hjr RoboJob Turn-Assist-E- Minimum Ø Of The Workpieces 25mm. Maximum Ø Of The Workpieces 400mm. Minimum Width Of The Side Of Hexagonal Workpieces 25mm. Maximum Width Of The Side Of Hexagonal Workpieces 170mm. Maximum Stacking Height 80-100mm. Maximum Stacking Weight 600kg. Width Of The Automation 1.902mm. Depth Of The Automation 740mm. Height Of The Automation 2,202mm. Weight Of the Automation 1,000kg. Robot 6 Axes. Maximum Reach 1,420mm. Maximum Payload At Wrist 12kg. Robot S/No. R16Y03327. RoboJob S/No. 35-17-352 (2017). Please note a loading charge of £100 + VAT will be added to the buyer's invoice. With Handwheel Robot Control, Sick Safety Light Unit, Quantity Of Material Separators/Supports, Flip Over Unit & Safety Screen. Robot Weight 130kg. Controller Weight 120kg. Please note a loading charge of £100 + VAT will be added to the buyer's invoice.

Condition: good (used), Year of construction: 2017, Standard turning diameter 150mm, maximum cutting diameter 255mm, maximum cutting length 685mm , Bar capacity main spindle 51mm, spindle speed 5,000rpm, Podezwm Hpopfx Ac Hogr sub-spindle 5,000 rpm, C axis 0.001 degrees, 3 x turrets 24 stations, Y axis +/-45mm, milling speeds 6,000 rpm, main spindle 15kw, Fanuc 31i, swarf conveyor, barfeed unit, parts catcher

Condition: used, Year of construction: 2011, Hankook VTC-160E CNC Ram Type Vertical Turning and Milling Centre with Fanuc 31i-Model A Colour CNC Control, Table dia. 1600mm, Maximum Swing 2000mm, Maximum Turning Dia. 2000mm, Maximum Turning Height 1400mm, Maximum Table Load 10,000kg, Horizontal Travel of Rail Head (X-axis) 1900mm, Vertical Travel of Ram (Z-axis) 900mm, Vertical Travel of Crossrail 700mm, Full C Axis 0.001 Resolution, Milling Spindle 18.5kw, Milling Spindle Speeds 30-3000rpm, Table Speeds. 0.7 to 280rpm (2 Speed Gear Box), Max Table Torque 23800 N.m, Ram Size 220mm x 220mm, Rapid Traverse (X-axis) 7,500mm/min, Rapid Traverse (Z-axis) 7,500mm/min, Cutting Feed Rate 0.001mm to 7500mm/rev, Tool Magazine 24 Station (12 Std + 12 Milling), Main Motor 45kw, Total Machine Power requirement 100KVa, Machine Size 5300mm x 4500mm, Machine Weight 34,000kg, Assorted Tool Holders. S/No. 42D09215 (2011). Country of Origin: Korea Pre-Auction offers Encouraged Pjdpfx Acozwnqcs Hjgr Location: These lots are located in Oldbury, West Midlands, UK. Unfortunately there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. All/Any tooling is being offered as specifically described.

Condition: used, Year of construction: 2003, functionality: fully functional, Mazak Quick Turn Nexus 150/500 YOM 2003 Mazatrol PC Fusion Control Mazak Tool Length Measuring System Serial Number 166285 Main Spindle has been fully refurbished 8 Station Turret Programable Tailstock Parts Catcher Pgsdpfjyplgtex Ac Hsr Swarf Conveyor RH exit Machine has been fully serviced Complete set of Machine Manuals UK buyers - Price £19,995 + VAT

Condition: good (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 63284-0012, turning length: 650 mm, turning diameter: 300 mm, spindle motor power: 15 W, spindle speed (max.): 5,000 rpm, spindle bore: 76 mm, travel distance X-axis: 215 mm, travel distance Y-axis: 110 mm, travel distance Z-axis: 680 mm, milling spindle length: 6,000 mm, type of input current: three-phase, bar passage: 65 mm, total height: 1,920 mm, total length: 3,130 mm, total width: 1,710 mm, spindle nose: A2-6, overall weight: 4,500 kg, Equipment: documentation/manual, MACHINE INFORMATION Manufacturer: Hyundai Model: KIA SKT2100SY Year: 2009 Condition: (Used) Great Serial Number: 63284-0012 Pgsdpozwhp Sjfx Ac Hsr Control: Fanuc Control Accessories: LNS Barfeed, Live & Static Tool holders, Swarf Conveyor, Parts Catcher, Tool Probe. Location: COVENTRY, UNITED KINGDOM MACHINE SPECIFICATIONS Control: Fanuc Control Bar Capacity: 65mm Chuck Size: 8″ Main, 6″ Sub Max Cutting Diameter: 300mm Max Cutting Length: 650mm Spindle Speed: 5000rpm Turret Positions: 12 Milling Speed: 6,000rpm Swing: 820mm X Axis Travel: 215mm Y Axis Travel: 110mm total (+55mm) Z Axis Travel: 680mm C Axis Travel: 0.001 degree

Condition: excellent (used), Year of construction: 2022, Turning diameter 376mm, turning length 760mm, Podpozt Spnjfx Ac Hjgr bar capacity 76mm, Y axis -/+ 52.5mm, C axis 0.001 degrees on both spindles, 24 station turret, 22KW Motor, Main spindle 4000rpm, sub-spindle 4500rpm, Fanuc I series, 3 jaw chucks, swarf conveyor, tool setter, LNS barfeed unit.

Condition: excellent (used), DOOSAN PUMA 3100 XLY CNC LATHE ONLY 2163 RUN TIME HOURS !!!!! UPGRADED FANUC I CONTROL 305 MM HYD CHUCK 420 MM TURNING DIA 2125 MM TURNING LENGTH MAX SWING 850 MM MAX SWING OVER CROSS SLIDE 670 MM Pgjdpfxjzumado Ac Hor X TRAVEL 293 / Y TRAVEL 130 MM / Z TRAVEL 2190 MM FULL C AXIS AND Y AXIS HYD STEADY - SMW SLU-X-4-MS ( CAPACITY 30 - 245 ) MAX SPINDLE SPEED 2800 TOOL PROBING DRIVEN TOOLS - 2+2 + STATIC HOLDERS SPINDLE POWER 35 HP YEAR 2012 THIS MACHINE HAS BEEN ONE OWNER ONE OPERATOR SINCE NEW - NEVER REQUIRED A REALIGNMENT - IMPECCIBLE CONDITION THROUGHOUT LOCATION NORTHERN IRELAND LOADING - FREE TRANSPORT CAN BE PRICED - PLEASE GIVE FULL ADDRESS

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 3087984, SPECIFICATION Swing over front apron 806mm Swing over cross slide 527mm Maximum cutting diameter 533mm Maximum turning length 660mm Spindle nose A2-6 Spindle bore 88.9mm Bar capacity 76mm Maximum spindle speed 3400rpm Spindle motor power 22kW Number of turret tool stations 12 Rapid traverse Z/X axis 24m/min Approximate weight 6500Kg Pgedpfx Acezwurao Hsr MACHINE EQUIPPED WITH: - Haas CNC control system Live tooling with C axis Collet chuck Tool setting probe Parts catcher Hydraulic tailstock Servo bar 300 magazine bar feed Swarf conveyor Interlocked guarding Automatic lubrication system Coolant system Manual

Condition: used, Year of construction: 2004, turning diameter: 660 mm, spindle speed (max.): 5,000 rpm, spindle speed (min.): 35 rpm, travel distance X-axis: 580 mm, travel distance Y-axis: 160 mm, travel distance Z-axis: 1,045 mm, total height: 2,600 mm, total length: 3,820 mm, total width: 2,060 mm, overall weight: 10,400 kg, Equipment: documentation/manual, CNC Turning Milling centre with Second Spindle CNC Control Mazatrol PC Fusion CNC 640 MT PRO Turning diameter 550/660 mm Turning length 1016 mm Spindle bore diameter 65 mm Spindle speed 35-5000 R/min X-axis movement 580 mm Y-axis movement 160 mm Z-axis movement 1045 mm B-axis travel 225 ° mm C-axis indexing 360° Spindle nose A2-6 Tool Taper Capto C6 Number of tools in magazine 40 Psdpjzv Sfbefx Ac Hegr If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail.

Condition: good (used), Year of construction: 2019, 256mm maximum cutting diameter, 455mm max turned length, 4,000rpm spindle speed, 51mm bar capacity, 12 station VDI turret, Pjdpfx Aszrfnusc Hogr milling speed 5,000rpm, 16kW spindle motor, Hurco WinMax 5 Control, tailstock, tool setter, swarf conveyor, parts catcher, Barfeed unit.

Condition: ready for operation (used), Pull tube for tensioning device from IKEGAI TURN 25 , length tube: 730 mm, Ø 75 mm, hydraulically operated, used, normal signs of wear, 100% functional ATTENTION: Please inquire for charges for packing and transport separately! ATTENTION: Please inquire for charges for packing and transport separately! Podpfxjzw S A Ae Ac Hogr

Condition: used, Year of construction: 2004, functionality: fully functional, turning length: 2,000 mm, Mazak CNC Mill – Turn Centre Model: E-650H Control: Mazatrol 640M Pro Year: 2004 Distance Between Centres: 2000mm Swing Over Bed: 905mm Machine With: C Axis Y Axis Live Tooling/Milling Pgedpfx Ajzlhp Iec Hor B Axis 800mm Power Chuck Manual Steady 375mm Open Steady 600mm Air Filer Mist

Condition: used, Year of construction: 2005, total height: 1,750 mm, total length: 1,350 mm, total width: 1,350 mm, Colour: Grey Weight: 415 kg Optimization cross-cut saw Stromab TR 500 Matrix 4 4000 Year of construction 2005 Engine power 10 hp Auto push-up system Inkjet printer - Year: 2005 - Documentation available: No - CE certificate present: No - Serial number: 250143 - Main motor power [kW]: 7.5 - Max. saw width [mm]: 375 - Arbor saw blade diameter [mm]: 30 - Input table length [mm]: 4300 - Output table length [mm]: 2000 - Transport dimensions: 1350mm x 1350mm x 1750mm (l x w x h) - Transport weight [kg]: 415kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT Psdpfx Aowq U Dxsc Hjgr VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2006, turning diameter 1000 mm swing dia. 1000 mm Z-axis stroke 900 mm control Siemens 840 D Pgodpfx Acezwg N Rs Her tool taper SK 50, VDI 60 tool piece magazine with 44 Plätzen workpiece weight max. 35 kg tool length - max. 500 mm

Condition: excellent (used), Webster & Bennett 72” CNC Elevating Rail Vertical Turning & Boring Machine Fanuc control Tool changer Table Size 72” Machine swing 84” Table speed Range 3.8 to 150 rpm. Feed range .156mm to 7.5mm per rev. Max Height under cross slide 48” Max Height under turret 48” Pgsdezrpmuspfx Ac Hjr Ram Travel 38” Main motor 50hp Fully interlocked guards with swarf conveyor

Condition: used, Year of construction: 2002, Chip conveyor (Sermeto): manufactured 07/2005 Pgodezwf N Nopfx Ac Hor Data Cooling unit (Aquatherm WLR 3000): serial no. 02VS3000203, manufactured 2002, cooling capacity 3.0 kW

Condition: used, Year of construction: 2002, Vertical Turning Center: GE Fanuc Series 18i-T CNC control Pjdpfx Acozwf Hbs Hjgr Data Automation Unit (Heilig O2101): manufactured in 2002