Used Cross-Léger for sale (4,514)

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bwodpfx Aou Tg I Dsa Noi Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: like new (used), Range (in depending on the lighting conditions) until: 15 m Bedjd Ecncspfx Aa Nswi Range with laser receiver: 30 m, & more 5 m: leveling accuracy +/-1 mm Self leveling range: 4° +-0,5 ° Accuracy of the horizontal line at 5 m: +-1.5 mm Accuracy of vertical line at 3 m +-0.75 mm Number of laser lines: 2 Weight: 485 g

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Bwjdpfx Aaefv Hphj Nei Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: used, Roller conveyor with chain cross conveyor Can be used after resaw. - Electric motor: 1,1 kW - Electric motor: 0,75 kW Bwjdpfxji Sdk So Aa Nsi - Electric motor: 1,1 kW

Condition: excellent (used), Year of construction: 2019, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: 8135.44, cutting height (max.): 100 mm, cutting depth: 300 mm, Great saw Bedpfx Aoyngniea Nswi

Condition: used, Year of construction: 2012, operating hours: 926 h, total height: 1,800 mm, total length: 11,250 mm, total width: 900 mm, Weight: 1.500 kg Price: On request - Year: 2012 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 546324 - Operating hours: 926 - Main motor power [kW]: 7.5 Bwedpfx Aaeyna Eze Nei - Max. saw length [mm]: 7209 - Max. saw width [mm]: 300 - Max. saw blade diameter [mm]: 500 - Arbor saw blade diameter [mm]: 85 - Input table length [mm]: 7850 - Output table length [mm]: 2400 - Options: Automatic pusher system - Voltage [V]: 400 - Current consumption [A]: 22 - Fuse [A]: 25 - Power [kW]: 11.0 - Transport dimensions: 11250mm x 900mm x 1800mm (l x w x h) - Transport weight [kg]: 1500kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2022, total height: 1,700 mm, total length: 10,000 mm, total width: 1,800 mm, Weight: 1.100 kg Price: On request - Year: 2022 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 8737 - Max. saw length [mm]: 6000 - Max. saw width [mm]: 300 - Min. saw blade diameter[mm]: 490 - Max. saw blade diameter [mm]: 500 - Arbor saw blade diameter [mm]: 30 - Input table length [mm]: 7000 - Output table length [mm]: 2000 - Options: Automatic pusher system - Voltage [V]: 400 - Current consumption [A]: 20 - Fuse [A]: 32 - Transport dimensions: 10000mm x 1800mm x 1700mm (l x w x h) - Transport weight [kg]: 1100kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Bedpfx Asyna Enoa Njwi Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: new, table width: 730 mm, travel distance X-axis: 500 mm, travel distance Y-axis: 200 mm, - Table size: 730 × 210 mm Bwjdjyqwnrspfx Aa Noi - Travel (X/Y): 500 × 200 mm

Year of construction: 2023, condition: new, Round wooden cross conveyors heavy duty 4 line length ca. 9m Strand distance 1500 mm 1800 mm 2300 mm height 1500 mm Bsdpfxodzx I Rs Aa Njwi

Condition: new, table length 600 mm table width 240 mm x-travel 370 mm y-travel 130 mm table height 165 mm Bodpfjfgvzusx Aa Njwi weight 60 kg dimensions 0,8 x 0,45 x 0,2 mm Cross table with turntable

Year of construction: 2002, condition: used, machine/vehicle number: 5713, - Manufacturer: Elmag Superfici - Type: TT1-30 - With cross carriage wheels - Length: 3,000 mm - Working width: 1,350 mm - Total width: 1,660 mm - Working height: 900 + - 20 mm - Height adjustable - Location, in stock Bwodpfx Aox Url Uea Nei - Volts, Hz 400 / 50 - Motor power 0.75 kW

Year of construction: 1994, condition: used, machine/vehicle number: 41094/30, Technical data: - Manufacturer: Cefla with cross axle - Type: TN/L - Length: 1.750 mm - Belt width: 1.400 mm - Total width: 1.600 mm - Height: 950 mm - Year of manufacture: 1994 - Feed rate approx. 2 - 8 m/min. - FU control for feed rate 50 Hz - Frequency converter required on site - Location: in stock - Volts, Hz 400 / 50 Bwedpfxsya H Hie Aa Noi - Motor power 0.75 kW - Voltage fluctuations max. +/- 5% - Location: in stock

Condition: used, Miter cross-cut saw for aluminum (special machine construction with 4 servo motors) Circular saw, miter saw, rip saw year of construction 2002 Saw blade diameter 500 mm Sawing range at 90° round Ø 180 Rectangle 350 x 140 mm (through longitudinal cut) Bwedpfx Aedzp T Doa Nsi Sawing range at 45° round Ø 180 Rectangle 350 x 100 mm (through longitudinal cut) Guide length of base support 1100 mm Travel on the base support (forwards and backwards) 650 mm Travel on the stand (up-down) 120 mm Saw blade speed approx. 3000 rpm Motor power 2.2 kW Mains connection 400 Volt, 50 Hz - Controlled longitudinal cutting movement - Controlled saw blade height adjustment - Controlled mitre cut through swivelling saw unit - Controlled miter cut by tilting saw unit - Pivoting and tilting of the saw via INDRAMAT servomotors with precision gears (MKDO71B-061-KG1-KN and MKDO41B-144-KP1-KN motor) - Vertical axis movement via INDRAMAT servomotors and ball screws (MKDO41B-144-KP1-KN motor) - a total of 4 Indramat servomotors are installed - very good German mechanical engineering Space requirement L x W x H 1150 x 1100 x 1400 mm weight approx. 360 kg good condition The unit comes from a special machine for special products. All other components and electrical parts for the construction of a new special machine are also available.

Condition: used, Year of construction: 2001, Wood dimensions to be processed: Input lengths min/max 500 - 6500 mm Full optimization up to max. 1500 mm Input widths min/max 40 - 300 mm Input thicknesses min/max 15 - 120 mm Wood cross-sections max. 300 x 40 mm max. 200 x 120 mm Fixed lengths after sawing min. 510 - 2800 mm Special application: Cutting blocks, length min/max. 100 - 200 mm (Caution: Multiple block lengths at the sorting line; blocks are transported to the end of the sorting line and fall into the customer's grid box). Cutting/cutting tolerance +/- 0.8 - 1.5 mm (for wood types with minimal resin content and an even surface. Tolerance up to 1 m fixed length, max. tolerance for longer pieces up to 2.5 m). Thickness tolerance +/- 3 mm. Curvature of the wood in all directions: max. 10 mm per meter in length. Wood types: soft or hardwood. System performance: Feed speed, continuously adjustable up to max. 230 m/cutting cycle 0.6 - 1. To obtain the practical output per day, an effectiveness factor dependent on the customer's production conditions must be calculated. Infeed and saw height: 900 mm (placed on customer's platform, saw requires concrete base). Sorting working height. 2000 mm Connection values: Total electrical connection value approx. 18 kW Operating voltage 380 Volt / 50 Hz Voltage fluctuations max. 5% Air consumption approx. 1200 NL/operating pressure approx. 8 bar Extraction speed approx. 30 m/nd Color pebble gray RAL 7032 and blue NCS 5030-R 80 B POSITION OVERVIEW: Item 1 Infeed and marking station with 1 side support table, adjustable 1 table as stop edge Item 2 Support roller without drive, front side in front of sheet metal table for easier feeding Item 3 Length measuring station with built-in fluorescence camera for detecting error markings Item 4 Automatic width measurement, contactless Item 5 OptiCut 304 optimizing cross-cut saw - right-hand version with built-in waste chute including equipment package for large wood cross-sections Graphic input terminal (16 x 40 characters, Numeric keypad) with software package for optimization and system control. Available for processing: - max. 16 product groups - max. 8 grades per product group - max. 200 fixed lengths per product group Item 6: Outfeed conveyor as sorting station with drive unit, length 7500 m Item 7: 2 ejectors mounted on the outfeed conveyor Storage location: Nattheim Bodow Sy T Hjpfx Aa Nowi

Condition: used, Year of construction: 1992, saw blade diameter: 550 mm, overall weight: 1,500 kg, power: 13 kW (17.68 HP), No. 3260 CNC cross-cut system Paul 14KE Used, year of construction 1992 (overhauled by the manufacturer in 2012) According to our customer / the previous owner, the machine is fully functional and can be viewed and tested on site Saw blade diameter 550 mm Speed 3500 rpm Bore 120 mm Connected load 13 kW Workpiece length 600 - 7000 mm Workpiece width maximum 380 mm Workpiece thickness maximum 100 mm Wood cross-section minimum 12 x 40 mm Wood cross-section maximum 45 x 380 / 100 x 200 mm 6 driven bottom rollers 6 non-driven top rollers CNC control MAXI x.3 Complete with infeed, outfeed conveyor, switch cabinet and control Technical documentation available Weight approx. 1500 kg Sale on behalf of customer, ex location near 99091 Erfurt, without dismantling, without transport and assembly Bodpfxsyl R Uuj Aa Nswi Dismantling, loading and transport by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical specifications, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or shipment Terms of delivery: ex location

Condition: used, band length ca. 1.700 mm + 2.700 mm Bsdpfx Aaev Hgb Nj Nowi cutting width max. 2.500 mm Cutting height max. ca. 80 mm

Condition: used, Year of construction: 2001, Abrasive belt length 1st unit: 2,150 mm Max. working width: 1,300 mm Number of belts: 3 Belt 1st unit: cross belt Design 1st unit: cross belt Sanding pad 1st unit: electronic segmented pad Abrasive belt width 1st unit: 150 x 4,800 mm Drive 1st unit: kW 2nd unit: longitudinal roller Design 2nd unit: steel calibration roller Abrasive belt length 2nd unit: 2,150 mm Abrasive belt width 2nd unit: 1,350 mm Abrasive belt speed 2nd unit: 18 m/sec 3rd unit: pad unit Design 3rd roller: electronic segmented pressure beam SDS system Sanding pad 3rd unit: electronic segmented, 32 mm width Abrasive belt length 3rd unit: 2,150 mm Abrasive belt width 3rd unit: 1,350 mm Suitable for lacquer sanding: yes Belt air blast: yes Vacuum conveyor: yes Feed speed, fixed: stepless 5 – 15 m/min Control: screen control Electrical/pneumatic belt oscillation: electrical Infeed height: variable (lower table moves) Table height adjustment: electric motor Table height display: digital Working height / feed table height: 880 mm Bjdoxzi S Nspfx Aa Nswi Location: Supplier

Condition: used, Year of construction: 2002, total height: 1,870 mm, total length: 2,100 mm, total width: 2,720 mm, Weight: 1.600 kg Price: On request - Year: 2002 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 595001 3 16 - Main motor power [kW]: 6.5 Bjdpjyf H H Hjfx Aa Nowi - Voltage [V]: 400 - Current consumption [A]: 15 - Fuse [A]: 20 - Transport dimensions: 2100mm x 2720mm x 1870mm (l x w x h) - Transport weight [kg]: 1600kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Catalogue number 7837 TECHNICAL DATA - Max. blade diameter: 450mm - Spindle diameter: 30mm - Top pneumatic hold-down - Blade guard - Blade guard also functions as a hold-down - Pneumatic blade stroke - Cutting height: 125x125mm, 100x250mm - Cutting capacity (thickness x width): 50x530mm, 100x480mm, 150x380mm, 200x200mm - Main motor: 5.6kW - Extraction port diameter: 100mm - Table dimensions (L/W): 660x480mm - Table height from base - 2 roller tables - Infeed roller table with guide: 1500mm - Outfeed roller table with guide and latch: 1500mm - Roller width: 300mm - Working pressure: 8bar - Overall machine dimensions (without roller tables) L/W/H: 940x780x1150mm - Weight approx. 450kg ADVANTAGES – German manufacture – DTR documentation – 2 roller tables Bwsdpfx Aaex Arhce Noi – Pneumatic blade stroke – Saw used, in perfect condition Net price: 14,900 PLN Net price: 3,550 EUR (based on exchange rate 4.2 EUR) (Prices may change in case of significant exchange rate fluctuations)

Condition: excellent (used), Stainless steel version, Length: 1400mm Bsdpfxehvyzwo Aa Njwi Width: 1200mm Height: 1900mm Weight: about 250kg

Condition: used, Year of construction: 2006, operating hours: 100 h, functionality: fully functional, Profi Industrial Cutting System (Longitudinal/Cross) – Grossmann – ONLY 100 operating hours! Description: For sale is a high-precision, automated longitudinal and cross-cutting machine from quality manufacturer Grossmann Maschinenbau. The system has a total runtime of no more than 100 operating hours. It is therefore in an almost mint technical condition and shows hardly any signs of wear on the mechanical components. Originally designed for cutting chip mats, this machine’s robust construction and versatile PLC control make it suitable for a wide range of materials (e.g. rubber, cork, fleece, composites, films, textiles, etc.). Technical highlights & features: Condition: Nearly new (max. 100 operating hours). Format: Maximum cut length 2,500 mm x maximum working width 1,200 mm. Bodpfx Asylxmfoa Nswi Complete line: Includes professional unwinder and winder for fully automatic material flow from roll to roll or roll to format. PLC control: Professionally programmed, with a choice between manual and automatic operation. Material handling: Automatic gripper feed positions material precisely in the end position, with integrated edge removal system for perfectly clean edges. Operation: Intuitive control via display, foot switch, and optical/acoustic production completion indicators (traffic light/horn). Precision: Integrated laser for exact material alignment. Safety: Fully enclosed design and modern safety monitoring. Versatility: This machine is a true all-rounder for any rolled material that needs to be cut to precise sheet sizes or strips. Its stable construction with a high-quality aluminum profile system ensures maximum rigidity. Complete documentation available, including process protocol, wiring diagrams, and technical drawings. The machine can be inspected and tested under power by appointment. For exact technical details and questions about fields of application, please feel free to contact me personally. Contact: Phone: 05427 9423 20

Condition: excellent (used), Year of construction: 2005, Connection values: Single phase, AC 50 ... 60 cycles Bwedpfxoxmhhyj Aa Noi Voltage switchable 200/220/240 V ± 10 % Power consumption: 110 W Heat emission: 95 kcal/h Application: Form depth 3…12 1/2" // Form width 148…470 mm Paper weight: Single webs 45…170 g/m2 // Multiple sets 125 ... 300 g/m2 Stack height up to ca. 300 mm The machine worked together in production with MICRO-FORMS LABELLER 18S (Sticks labels on sheets) // Ref. No.: 40016.25

Condition: good (used), Year of construction: 1994, Automatic defect cross-cut system Wood width max. 260 mm Wood height max. 100 mm Saw 7.5 kW Feed 6 kW Bwodpekv Untefx Aa Nji worked 1995 - 2012 approx. 4 hours/day

Condition: used, Format: 310 x 432mm Equipment: roller adjustment: fully automatic model: flat pile feeder with air-suction type of fold: single fold, parallel fold, short fold, letter fold, according fold, gate fold sheet size: max. 310x432mm; min. 125x130mm paper weight: 50-190g/sqm pile height: 50mm speed: max. 240 sheets/min. power: 230V/50Hz - 0,6kW dimensions: 1.060x553x670mm weight: 45kg Bjdpfx Ajx N I Uhsa Nowi

Year of construction: 2015, condition: ready for operation (used), A Trivec wood sanding machine for producing a rough-sawn appearance by means of cross sanding is available. Working width: 400mm, max. product length: 300mm, clearance height: 120mm, working height range: 880mm-920mm, feed rate: 16m/min, sanding belt length: 2600mm, sanding belt width: 150mm. Machine dimensions X/Y/Z: approx. 1450mm/1100mm/1300mm, weight: approx. 750kg. Documentation available. An on-site inspection is possible. Bodpfx Aoynltwsa Newi