Used Guillotines for sale (885)

Condition: used, LVD Shear Type HST C-10/31 Capacity 3000 x 10 Hnsdpfx Aex Tqtbsddsg

Condition: refurbished (used), Year of construction: 2020, functionality: fully functional, The Autobyte 3602D is an automated cutting system equipped with premium Morso guillotine blades for perfect corners in wood, plastic, and MDF. With a capacity of over 500 frames per hour, material savings are achieved thanks to the minimal saw kerf of just 1 mm (as opposed to 6 mm with conventional saws). The automatic material feeder accommodates up to 13 lengths, clamps ensure secure holding, and a splitter sorts cut pieces while removing waste. Control is via Mitsubishi touchscreen and PLC, with pneumatics supplied by SMC. Hnedpfjw U D E Ejx Addeg

Condition: used, Year of construction: 1982, sheet width - max. 1255 mm plate thickness 4.0 mm ST plate thickness 2.0 mm VA plate thickness 6.0 mm ALU number of strokes - loaded ~ 66 Hübe/min. cutting angle 1.5 ° back stop - adjustable max. ~ 1.000 mm total power requirement 5.5 kW weight of the machine ca. 2600 kg. range L-W-H 1750 x 1800 x 1800 mm Hodpfx Ajxaa I Soddjng Machine from a technical college - prototype construction very well-maintained condition (!!) Furnishing: - electro-hydraulic guillotine shears - manual backgauge with analogue position display (scale + magnifying glass) - electrical cutting length limitation - manual cutting gap adjustment - 1x extra long side stop - 2x extra long support arms - 1x free moving footswitch - rear sheet metal slide - User manual (PDF) * Machine link : ?machineno=1008-9325278

Condition: used, Hydraulic Plate Shear LVD Type HST-C 31 / 6 Hodpfx Adotvb Iuodong Machine No. 21348 Year of manufacture: 1994 Cutting length: 3,100 mm Cutting thickness: 6.35 mm Backgauge: 770 mm Working height: 950 mm Hydraulic sheet hold-downs: 17 units Hydraulic tank capacity: 150 liters Motor power: 7.5 kW Power connection: 400 Volt, 50 Hz, 9.5 kW, 19 Amp. - Motorized backgauge with digital actual position display ELGO - Backgauge adjustment via push button – rapid in both directions and fine adjustment by jogging in the minus direction only - Sheet lifting device below the backgauge with pneumatic lifting cylinder - Continuously adjustable blade gap from 0.1 mm via handwheel with analog display - Cutting angle adjustment in 5 steps from 1.5° to 3.5°, electrically pre-selectable - Left side angle stop 1,500 mm - 2 table extensions as sheet supports - Electric foot switch - Comprehensive operating manual Space requirements without front table extension (L x W x H): 4,150 x 1,850 x 1,900 mm Space requirements with front table extension (L x W x H): 4,150 x 2,850 x 1,900 mm Weight: 5.5 tons Good condition Very good cutting results, including with thin sheet metal

Condition: used, Year of construction: 2008, sheet width 3200 mm plate thickness 6 mm Hodpfxsqva Rze Addjng distance between columns 3200 mm back stop - adjustable 20 - 600 mm dimensions ca. 4010 x 1610 x 1620 mm engine output 7,5 kW Control eView weight of the machine ca. 7,2 t CNC swing cut panel shears electrical components from Siemens, ABB and Mitsubishi, Pilz safety control hydraulic components made in Italy 3 support arms and 1 angle stop Ball rollers in the table Operating instructions available

Condition: ready for operation (used), Year of construction: 2013, Economically stable motorized guillotine shear (used) Hodpfxsxxia Is Addsng Heavy-duty welded steel construction Technical Data: Condition: good used, ready for operation Year of manufacture: 07/2013 The machine is powered and can be viewed by appointment! Weight, approx.: 2,580 kg Sheet thickness for St. 42 (max): 3.5 mm Max. sheet length: 2,500 mm Backgauge: 20–1,000 mm Cutting angle: 2° Working height: 800 mm Strokes per minute (automatic mode): 45 strokes/min Electrical connection: 400 V Motor power: 7.5 kW Dimensions: 2,900 x 1,350 x 1,200 mm Electric backgauge Digital measuring system for backgauge Light curtain

Condition: excellent (used), functionality: fully functional, Year of construction: 2017, Amada Hydraulic Guillotine Shear Type GX II 630 Working width: 3050 mm Max. sheet thickness: 6.35 mm Robust CNC electro-hydraulic guillotine shear AMADA CNC touch control, located front left ("GP 37W2") Machine control system including information display Main display with 4 operating panels Hsdexwmycepfx Addjng Control/operation of all machine functions Up to 50 cutting programs, each with up to 15 sequences CNC electromechanical backgauge Travel speed: 100 mm/sec CNC electro-hydraulic cutting angle adjustment CNC electro-hydraulic blade gap adjustment Sight device & cutting line illumination for viewing the scribe line Shearing according to optical scribe mark Manually adjustable table support plates including ball rollers Grip recesses in the front support table 2x movable foot switches Operating manual and circuit diagrams included

Condition: as good as new (ex-display), The KHT H 3010 CNC + sheet holding device is a state-of-the-art guillotine shear from KNUTH, designed for precise and powerful cutting within the category of Guillotine Shears and the product group of Hydraulic Guillotine Shears. Built with a highly rigid frame and guided cutter bar, it minimizes twisting in the workpiece, ensuring optimal cutting accuracy while reducing rework. The user-friendly Cybelec Touch 8 control system operates via a touchscreen, allowing you to input the length, thickness, and strength of the plate material to automatically adjust kerf, cutting angle, and length for optimal results. This robust machine accommodates materials up to 10 mm thick, making it suitable for stainless steel sheets, while features like hydraulically regulated hold-downs guarantee steady fixation of materials during the cutting process. Safety is prioritized with advanced features like a light barrier and foot pedal emergency switch, adhering to the latest CE regulations. To expand the functionality of this Hydraulic Guillotine Shear, the innovative plate hold-up feature supports the plate during positioning for high precision. For further information, you can request a quote or order online. Hnedpfsq I Nb Tjx Addsg

Condition: good (used), Year of construction: 1991, sheet width - max. 1010 mm plate thickness 4.0 mm ST plate thickness 2.5 mm VA plate thickness 6.0 mm ALU number of strokes - loaded max. 20 Hübe/min cutting angle 1.5 ° work height max. 900 mm Control ELGO back stop - adjustable max. ~ 1.000 mm Hsdpjxrgv Tofx Addeng total power requirement 5.5 kW weight of the machine ca. 2200 kg. range L-W-H 1500 x 2155 x 1606 mm from a maintenance workshop good condition (!!) - in checked conditions - machinevideo - ?v=w22S17mfU-A Equipment: - Robust NC electro-hydraulic guillotine shear - NC electro-motorized backgauge * Includes NC ELGO positioning control "TYP 85" - Electric cutting length limiter - Manual cutting gap adjustment - 1x side stop with scale - 2x support arms - 1x freely movable foot switch - Original operating instructions * Special accessories included: - Pneumatic holding device for thin sheet metal blanks

Condition: used, // Sold as is or reconditioned // Vacuum paddle dryer mixer Used for products such as powders/powdery substances. Hodpfox Rz Spex Addong 316 stainless steel Tank diameter 1000 x 2000 Volume: 1100 litres Jacketed 86 litres / 1 bar - 120°C Heated agitator 235 litres / 1 bar - 120°C Agitation by 8 scraping blades Loading via 400 diameter Discharge 350 diameter with guillotine valves ADF 15 kW motor Self-cleaning filter

Condition: good (used), Motorized guillotine shears (used) Manufacturer: RAS Model: 82.10 Max. cutting length: 1040 mm Max. sheet thickness for Steel 40: 2.5 mm Distance between supports: 1040 mm Continuous hold-down bar Backgauge travel range: 5 – 500 mm Motor power: 2.8 kW Machine weight: 750 kg Space requirements: Depth 2000 mm, Width 1400 mm, Height 1100 mm Foot switch Backgauge can be manually adjusted from the front Support arms (front) The machine is in very good condition and immediately ready for operation. Forklift available, free loading onto truck Affordable shipping possible Machine location: 48477 Hörstel Hedpfxox T At Te Addsng

Condition: excellent (used), Year of construction: 2017, Ref: 11039 . 2017 Rollem 36” Jetslit + 30” Rollaway and Cassette AutoCollator Delivery High volume print finishing system to maximizes finishing productivity for large volume producers For greeting cards, photo books, direct mail, postcards, invoices, business cards, game cards and much more. Hjdpfx Adjxyxttedeng Features: This flexible system takes full press sheets and converts them to finished products in one step, eliminating the need for guillotine cutting, excess manpower and paper movement. 100% accuracy of finished products is a key feature of the Jetslit. Performs multiple print finishing steps with one system Bi-directional slitting, cutting, creasing and perforating in one machine Ideal for high volume production Multiple-up layouts maximize press sheet Decreases excess labour costs Eliminates touch points and paper movement Fully integrates with press via DFA communication system Accepts sheets in-line from press or operates in a stand-alone near-line configuration Process: The system takes full printed sheets with multiple images and converts each sheet in two directions, as shown below: 1. Full sheets are fed into the JetSlit registration guide for perfect alignment. 2. The sheets are completely slit on the extreme edges and timed slit in-between with Rollem's patented strike-slit feature. 3. The sheets are turned 90 degrees and re-registered. 4. Final slits are made, removing the notched portions and leaving the final pieces. Specification: Speed: Up to 6,000 cut product sheets per hour Format: Up to 36’’ (915mm)

Condition: excellent (used), functionality: fully functional, Baykal hydraulic guillotine shear type HNC 8100/6 working width 8100 mm Hedpjx Rbhdofx Addjng maximum sheet thickness 6 mm motorized backgauge automatic blade gap adjustment automatic cutting angle adjustment sheet support device

Condition: new, The KHS E 1000 Manual Guillotine Shear is an essential tool in any locksmith's shop, designed for the precise and robust cutting of large steel plates. This classic manual plate shear features a sturdy cast-iron construction, ensuring durability that can withstand the demands of multiple generations of use. With a working length of 1,040 mm and the ability to handle plate thicknesses up to 1.5 mm while maintaining safety, it combines efficiency with operator comfort thanks to its counterweights and adjustable table stop. The KHS E 1000 also includes a conveniently adjustable back-gauge, making it easier to produce consistent cuts. Request a quote today to enhance your sheet metal processing capabilities with this reliable manual guillotine shear, a perfect fit for any guillotine shears category. Hodpen D Ehvsfx Addeng

Condition: ready for operation (used), Year of construction: 1997, sheet width 3230 mm plate thickness 2.5 mm thickness at "Niro-steel" 1.5 mm no. of strokes 28 - 42 Hub/min cutting angle 1.60 Grad table height 820 mm distance between columns 3540 mm Control ELGO 87P engine output 6.8 kW weight of the machine ca. 3410 kg. range L-W-H 4070 x 2070 x 1400 mm from a maintenance workshop including special accessories (!!) Hnsdpjxacd Nofx Addsg Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - NC electro-motorized back stop - including NC ELGO "TYP 87P" digital control unit * adjustable from the front right * with target/actual value position input * continuous adjustment over the entire travel range * rough adjustment via push buttons * protection of the limit values ??with limit switch - "Duo-Cut" drive with two dynamic, powerful gear motors - support table with recessed grips - hold-down bar with hard rubber strip - all-steel knife with two cutting edges - selector switch for single and continuous stroke - 1x freely movable foot switch - safety device at the rear - original operating instructions Special accessories included: - pneumatic sheet holding device for thin sheet metal cuts - 1x extra long side stop, including support foot + digital stop - 2x extra long, front support arms * with "SLIDING" mount - for easy moving

Condition: used, functionality: fully functional, Year of construction: 1985, Capacity: 3100 x 12,7 mm. Backgauge: Motorized. Adjustable blade angle: Yes. Adjustable cutting length: Yes. Adjustable blade gap: Yes. Year: 1985 Country of origin: Belgium. Size (L x W x H): 4100 x 2900 x 2170 mm. Weight: 8800 kg. With ligth guard for back gauge, angle and support arms. Hnjdsxwmu Hopfx Addog All our machines will be tested and serviced before delivery.

Condition: good (used), functionality: fully functional, Year of construction: 1994, machine/vehicle number: 94094175, sheet thickness (max.): 6 mm, input voltage: 380 V, overall weight: 7,000 kg, total length: 3,500 mm, total width: 2,200 mm, total height: 1,600 mm, HACO TS 3006 Guillotine Shear - Max. sheet thickness: 600 mm - Max. sheet width: approx. 3200 mm Note: The item can be collected from 16.02.2026 on a date to be agreed. Hjdpfx Adex Uymmjdeng FCA D-73529 Schwäbisch Gmünd – loaded onto truck

Condition: excellent (used), Year of construction: 2017, Ref: 11038 . 2017 Rollem 36” Jetslit + 30” Rollaway and Cassette Delivery Hjdpfxoxyxr No Addsng High volume print finishing system to maximizes finishing productivity for large volume producers For greeting cards, photo books, direct mail, postcards, invoices, business cards, game cards and much more. Features: This flexible system takes full press sheets and converts them to finished products in one step, eliminating the need for guillotine cutting, excess manpower and paper movement. 100% accuracy of finished products is a key feature of the Jetslit. Performs multiple print finishing steps with one system Bi-directional slitting, cutting, creasing and perforating in one machine Ideal for high volume production Multiple-up layouts maximize press sheet Decreases excess labour costs Eliminates touch points and paper movement Fully integrates with press via DFA communication system Accepts sheets in-line from press or operates in a stand-alone near-line configuration Process: The system takes full printed sheets with multiple images and converts each sheet in two directions, as shown below: 1. Full sheets are fed into the JetSlit registration guide for perfect alignment. 2. The sheets are completely slit on the extreme edges and timed slit in-between with Rollem's patented strike-slit feature. 3. The sheets are turned 90 degrees and re-registered. 4. Final slits are made, removing the notched portions and leaving the final pieces. Specification: Speed: Up to 6,000 cut product sheets per hour Format: Up to 36’’ (915mm)

Condition: used, Max. cutting length: 3,000 mm Max. sheet thickness: 6 mm steel Motorized backgauge with digital display up to 1000 mm Side stops and table extensions cutting length limitation Cutting edge lighting Hydraulic shear angle adjustment Hnedpfx Adsvmz Nbjdjg knife sharpened Weight: approx. 6500 kg

Condition: new, The KHT V 3010 CNC is a cutting-edge guillotine shear designed for the Sheet Metal Processing category, providing precision and reliability in a robust package. Produced in a state-of-the-art facility, these hydraulic plate shears feature a guided cutter bar with an adjustable cutting angle, significantly reducing workpiece twisting and minimizing rework. Its user-friendly touchscreen control allows for automatic optimization of cutting gap, angle, and length. The machine’s structure is built for durability, with a heavy, welded frame and top-quality components, ensuring longevity and precise cuts. Furthermore, with a maximum plate thickness of 10 mm and effective hydraulic systems for steady operation, the KHT V 3010 CNC is ideal for demanding production environments. Additional accessories enhance its versatility. Experience the precision of the KHT V 3010 CNC for your guillotine shear needs. Request a quote today to learn more about how this machine can fit into your operations. Hnjdpfx Adjww T Snodsg

Condition: new, Year of construction: 2025, sheet width 1320 mm plate thickness 2.5 mm ST thickness at "Niro-steel" 1.2 mm blade length 1350 mm no. of strokes 34 Hub/min back stop - adjustable max. 825 mm cutting angle 1.5 ° work height max. 810 mm Hsdpfx Aexabz Hjddong Control konv. engine output 3.0 kW weight 1100 kg range L-W-H 1950 x 1450 (2000) x 1200 mm Exhibition machine - like new Never been used (!!) Special price upon request Features: - Robust electro-mechanical sheet metal shear - Heavy-duty / robust drive motor - Manual backgauge, including analog position indicator * Adjustment range max. 825 mm - Manual cutting gap adjustment - 2x table side stops including mm scale - 1x front stop bar - manually adjustable - 2x front support arms - Grip recess in the front work table - 1x freely movable foot switch, including emergency stop button - Control cabinet/operating panel - front right - Rear safety device - Rear sheet chute - Connection cable + plug

Condition: new, Year of construction: 2025, ABKANTBANK-Technik Halver, YOUR competent partner for BENDING MACHINES and guillotine shears. We are your contact for high-quality sheet metal processing. As a long-standing sales partner of the Polish manufacturer PROD-MASZ, we respond to the needs of our customers on site and see ourselves as an extension of production. Appropriate machines can be demonstrated if required, along with competent advice and professional instruction. We advise you individually - according to your wishes and look forward to your inquiry. Plate shears 2500/1.2mm - Working length 2500mm - Stable and robust construction Hnsdpsnxlndjfx Addjg for steel plates up to 1.2mm - Large cast work table - Open design suitable for continuous cuts - Back stop with scale - Declaration of conformity - CE mark Dimensions: Length: 3000mm Width: 750mm Height: 1150mm Weight: approx. 600 kg Clearance: 8cm Shipping within Germany 360€ All prices are subject to 19% VAT. Pick up yourself Cash on delivery Other dimensions 1000mm and 3000mm on request Contact:

Condition: excellent (used), Year of construction: 2012, Ref: 11027 . 2012 Polar 115 XT Flowline Polar 115cm guillotine with paper handling system. Equipped with: Frequency controlled drive motor Variable speed back gauge Colour touch screen Automatic programming Memory Storage Capacity Variable pressure clamp for various stocks Chrome central air bed Hedpfx Adsxx Uukjdsng Chrome side tables left & right with air 2 x Spare knives Knife changing device Rear Table Guard I.R. light beam guarding Accessories: 2012 LW1000-4 Lift 2012 RA-4 Jogger 1999 TR130-ER4 Downloader Specification: Cutting width, Max: 115 cm Clamp opening, Max: 16.5 cm Feed depth, Max: 115 cm Power required : 5Kw

Condition: new, The KHT 3010 M NC is a high-performance hydraulic guillotine shear designed for precise sheet metal processing. This robust machine features a swing-beam design with a cutting bar guided in a pivot bearing, ensuring straight cuts without upper and lower blades jamming. It is equipped with an Estun E21 NC control system, allowing for precise positioning of the robust back gauge, ideal for rough production environments. The large work table with roller balls and sturdy support arms facilitates easy handling and safe plate alignment, while the hydraulically regulated hold-downs ensure steady fixation of the sheet metal during operation. This versatile guillotine shear is suitable for cutting stainless steel and offers user-friendly controls, including a mobile foot pedal with an emergency stop switch. Safety features comply with the latest CE regulations, providing a secure working environment. For unparalleled quality and reliability in hydraulic guillotine shears, consider the KHT 3010 M NC. Request a quote today to add this exceptional machine to your sheet metal processing lineup. Hnsdpfx Aov Rbyhoddeg

Condition: new, The KMT M 1503 Guillotine Shear is a high-quality machine tool designed for precision cutting in the Sheet Metal Processing category. Its robust construction features a solid steel weldment coupled with a sliding-block guided cutter bar, ensuring reliable and accurate performance. Equipped with a powerful drive motor, this machine minimizes workpiece torsion during cutting, which is enhanced by its high-precision manual back gauge that simplifies positioning. The KMT M 1503 comes with special cutters for stainless steel, reversible upper cutters, and multiple cutting surfaces, making it versatile for various applications. Its ergonomic design includes bright LED illumination for improved visibility, ensuring clear alignment with the marked cut line. With a substantial maximum plate thickness of 3 mm for materials up to 450 N/mm² and a working length of 1,560 mm, this shear optimizes efficiency in the workplace. For added safety, the work area is secured by a light curtain, and convenient features such as a mobile foot switch and accessible maintenance points are integrated. Request a quote now to experience the performance of the KMT M 1503 Guillotine Shear, an exemplary tool in the Sheet Metal Processing product group. Hnjdpfxjwhi Uae Addsg