Used Hydraulic Section Bending Machine for sale (90,086)

Condition: good (used), Year of construction: 1994, control type: CNC control, controller manufacturer: Siemens, controller model: 840 D, Pipe diameter: 168.3 x 11 mm Pipe insertion length: 6000 mm Maximum bending radius: 700 mm Control system: Siemens 840 D Minimum bending radius: 80 mm Maximum bending angle +/-: 190 ° Connected load: 400 V / 50 Hz / 85 A Dimensions (L/W/H): 11.9 x 2.7 x 2.45 m Machine weight approx.: 33 t Additional information: - CNC control: CNC MMI Multicontrol 2000 Giodpfx Absx T Dguodel - Control system NCU - PLC: Siemens Simatic S7 - Electrical connection: 400V / 50 Hz / 85 A The machine is fully automatic and equipped with a tool changer. The following tooling is available: Pipe Ø 48.3 mm; Radius 105 mm Pipe Ø 60.3 mm; Radius 120 mm Pipe Ø 63.5 mm; Radius 150 mm Pipe Ø 76.1 mm; Radius 190 mm Pipe Ø 88.9 mm; Radius 222 mm Pipe Ø 114.3 mm; Radius 285 mm Pipe Ø 139.7 mm; Radius 350 mm Pipe Ø 141.3 mm; Radius 700 mm Pipe Ø 168.3 mm; Radius 420 mm A few mandrels have a direct engraved marking. These have the following specifications: 88.9 x 8 mm; 88.9 x 4.5 mm; 114.3 x 8.8 mm; 139.7 x 8.8 mm; 168.3 x 12.5 mm; 168.3 x 8.8 mm The following outside diameters of the mandrels were measured: 23.2 mm; 32.3 mm; 37.1 mm; 41.5 mm; 59.3 mm; 70.3 mm; 77.7 mm; 80.9 mm; 88.7 mm; 93.2 mm; 94.7 mm; 103.0 mm; 112.8 mm; 118.8 mm; 128.9 mm; 138.5 mm; 147.2 mm; 153.6 mm The accessory package is valued at approximately €150,000.

Condition: good (used), Year of construction: 1990, machine/vehicle number: 103 2583310, Offer 25326 Technical Data: - Saw blade diameter up to 400 mm - Cutting capacity at 90°: - Round: 130 mm - Square: 120 mm - Rectangular: 300 x 40 mm or 240 x 80 mm - Cutting capacity at 45°: - Round: 130 mm - Square: 110 mm - Rectangular: 245 x 40 mm - Mitre adjustment left & right each 0–90° - 2 cutting speeds - Drive: 400 V / 1.26 / 2.5 kW - Saw blade feed rate hydraulically infinitely adjustable - Coolant system - Required space approx. W 1100 x H 1980 x D 1210 mm Giedpfx Aex Sxx Aebdel - Weight approx. 950 kg - Infeed and outfeed roller conveyors with length stop, each 6000 mm

Condition: as good as new (ex-display), Year of construction: 2024, sheet width 1550 mm plate thickness 4.5 mm pre-bending 4.0 mm roll length 1550 mm min. dia. 190 mm roll diam. toproll 130 mm bending speed 5.3 m/min engine output 2.2 kW weight 1360 kg range L-W-H 2320 x 900 x 1200 mm Exhibition machine from 2024 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - robust electro-mechanical round bending machine - 2x central rollers driven by electric motor (upper & lower roller) - upper roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - lower roller can be adjusted manually, using a handwheel - asymmetrical roller arrangement - self-braking main motor - safety device (safety line with switch unit) - CE mark/declaration of conformity Special equipment included in the price: Godpfjxaaa Ujx Abdeil - hardened rollers - motorized side roller adjustment - digital position display for motorized adjustable side roller

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, overall weight: 14,000 kg, working height: 1,000 mm, sheet thickness aluminum (max.): 3 mm, working length: 2,160 mm, TECHNICAL DETAILS Maximum bending length: 2,160 mm Maximum sheet thickness (steel, 400 N/mm²): 2.0 mm Maximum sheet thickness (stainless steel): 1.5 mm Maximum sheet thickness (aluminum): 3.0 mm Minimum bent part length (without corner pieces): 260 mm Minimum bent part length (with 30 mm corner pieces): 450 mm Minimum bent part length (with 50 mm corner pieces): 500 mm Maximum external bent part width: 1,500 mm Minimum internal bent part width: 150 mm Maximum bent part height (four-sided): 203 mm Gjdpfox Ngpkex Abdoil Lateral clearance at the corner pieces: 30/50 mm Clearance in front of upper beam tool: up to 60 mm Bending beam swivel range: 180 degrees Working height: 1,000 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 5,350 x 7,300 x 2,450 mm Approx. weight: 14,000 kg Maximum drive power: 25 kW Note: The vacuum stacking unit, neck and thread cutting device, and welding fixture visible in the images are not included in the scope of delivery or sale.

Condition: ready for operation (used), Year of construction: 1987, operating hours: 70,000 h, functionality: fully functional, machine/vehicle number: 21104, working range: 250 mm, feed length X-axis: 170 mm, overall weight: 1,600 kg, total height: 1,860 mm, pressing force: 7 t, total length: 2,000 mm, total width: 2,500 mm, table width: 184 mm, input frequency: 50 Hz, input voltage: 400 V, input current: 8 A, compressed air connection: 6 bar, Bihler Automatic Machine M35 – Year of manufacture 1987 – 7 t press force – ready for operation For sale is a Bihler automatic machine, model M35, year 1987, in very good and well-maintained condition. The machine features a press force of 7 tons, a compressed air connection with 6 bar, and has approximately 70,000 operating hours. Gisdox Tukqjpfx Abdel The automatic machine is fully functional and immediately ready for use. Bihler machines are renowned for their robust, long-lasting construction and reliability in industrial applications. The M35 is ideally suited for stamping, bending, and forming operations. The machine can be inspected under power in our workshop by prior appointment. Spare parts are still readily available.

Condition: used, - Pressing force 25 t - Throat depth 750 mm Giedpfx Ajx Tvhwebdjl - Max. punching diameter 110 mm - Hydraulic tool clamping - Stroke adjustment with digital display - X / Y with digital display - Table size 1600 mm x 1050 mm - Weight approx. 2000 kg

Condition: ready for operation (used), Year of construction: 1979, Two Bihler GRM-50 are available, year of manufacture: 1979/1987. Feed length: 320mm, max. strip width: 40mm, wire diameter range: 0.5-5mm, center punch stroke: 52mm, max. production speed: 132 pieces/min. Dimensions X/Y/Z: approx. 2600mm/1500mm/1900mm, weight: approx. 3500kg. Gisdpetvar Iefx Abdsl

Condition: ready for operation (used), Year of construction: 2019, operating hours: 14,674 h, Control Unit Model CC300 microcomputer Brand ENGEL Injection Unit Screw diameter 45mm Gijdpfx Abjx Nr Tnedel Clamping Unit Clamping force 500 tons Additional Equipment Tool heating: 32 control circuits, max. heating output 60 kW Vacuum compressed air circuits: With Venturi nozzle and pressure switch Solenoid air valves: 2/2-way, R1/2 inch Autoprotect injection monitoring: Self-learning system for mold protection Advanced material package: For thermoplastics up to 350°C, max. reinforcement level 30% This Engel Duo 740 H / 740 M / 500 WPX combi M injection moulding machine was manufactured in 2019. It features a two-plate compact design, minimal footprint, and intelligent servo-hydraulics for reduced energy consumption. The machine includes a CC300 microcomputer control system with a 21.5" full HD touch screen and advanced material package suitable for thermoplastics up to 350°C. For more information about this injection moulding machine, please reach out to us. Application Types Injection Moulding

Condition: good (used), Faceplate bending machine, profile bending machine, bending machine, angle bending machine, pipe bending machine Gijdpfx Abjfg Th Ajdjl -Diameter of faceplate: 1330 mm -Clamping disc diameter: 775 mm -For an additional charge: other round shapes can be produced -Geared motor power: 1.5 kW -Speed: 86 rpm -Dimensions: 2440/1330/H1400 mm -Weight: 1420 kg

Condition: good (used), Year of construction: 1990, Type RHM III 120 v-1000 Roll diameter: 120 mm Working length: 1000 mm Sheet thickness: up to 5.0 mm 400 Volt Kramer Maschinenbau GmbH Description The features described for the RH II series also apply to the RHM III series. These round bending machines are designed for continuous operation under maximum load. The lower shaft is adjustable via a worm gear. For models RHM III 90 – RHM III 130, the geared brake motor is flange-mounted on the outside, while models RHM III 140 to RHM III 180 are equipped with an internally flange-mounted geared brake motor. All motorized machines come standard with electrical safety control. Operation for forward and reverse is carried out using a double footswitch. Additional features on type RHM III: ▪ Powerful thermally protected geared brake motor ▪ Electrical safety control ▪ Convenient double footswitch for forward/reverse ▪ Three-shaft drive (particularly recommended for thin sheet work) ▪ Drive system with two operating speeds ▪ Overload protection via slipping clutch ▪ Motorized rear shaft adjustment ▪ Motorized lower shaft adjustment Standard equipment: ▪ Gear side drive ▪ Three-shaft construction ▪ Asymmetrical shaft arrangement ▪ Upper shaft can be swung out to the front ▪ Adjustment of lower and rear shafts via handwheel ▪ Conical bending by tilting the lower and rear shafts ▪ Initial bending capacity equals round bending capacity Godpfx Abjx Niu Nsdsil Optional equipment: ▪ Device for conical rolling ▪ Upper shaft with grooved edge ▪ Lower and rear shafts with wire groove ▪ Surface-hardened shafts ▪ Ground shafts

Condition: ready for operation (used), Year of construction: 1979, operating hours: 70,000 h, functionality: fully functional, machine/vehicle number: 24104, working range: 250 mm, feed length X-axis: 170 mm, overall weight: 1,600 kg, total height: 1,860 mm, type of input current: three-phase, pressing force: 7 t, total length: 2,000 mm, total width: 2,500 mm, table width: 184 mm, input frequency: 50 Hz, input voltage: 400 V, input current: 8 A, punching force: 7 t, control cabinet width: 410 mm, control cabinet length: 630 mm, control cabinet height: 1,320 mm, compressed air connection: 6 bar, With 70,000 operating hours, it has certainly seen considerable use, but this is not an unusual figure for machines of this type in industrial operation – many remain productive for years with far higher hours if they are properly maintained. Full functionality is assured – the drive has been replaced once. On the positive side, the machine is fully operational, proven in industrial environments, robust, and there are still many spare parts available for older Bihler machines. Gsdpfx Ajx Ttb Uobdsil

Condition: used, Year of construction: 1990, pressure ca. 20 t Gisdpfx Absx E Dt Sjdjl

Condition: new, sheet width 1250 mm plate thickness 5.5 mm pre-bending 5.0 mm roll diam. toproll 140 mm min. dia. 210 mm turning speeds 5.7 U/min engine output 2.2 kW weight 1365 kg Gedoxaacvepfx Abdeil range L-W-H 2020 x 900 x 1.200 mm Furnishing: - Robust electro-mechanical bending machine - 2x central rollers driven by an electric motor (top and bottom roller) - Top roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - Lower roller manually adjustable, by hand wheel - asymmetrical roller arrangement - self-braking main motor - Safety device (safety line with switch unit) - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized side roller adjustment - Digital position display for motor-driven adjustable side roller

Condition: good (used), I am selling a HILMA-ROEMHELD machine vice, good condition. Gjdpfxov Upvrj Abdoil

Condition: good (used), Bending tool, die, lower knife, lower tool, lower jaw -Tool: for swivel bending machine -Widthen: for lower cheek Gijdpfx Ascn Shuebdol -Dimensions: 59 x 19 mm -Length: 1452 mm -Weight: 10 kg

Condition: new, bending length: 2600sheet thickness: 6upper roll diameter: 190 Technical specifications: - Hardened and polished rolls - Conic bending device - Digital readout for side rolls - Complete body made of ST-52 Steel - Portable control panel separated form machine - Rolls are mounted with bearings Giedpfx Aox Twiiobdol - Top roll cover, openable and closeable by hydraulic, controlled from control panel. - All rolls are driven by hydraulic motor and planetary gearbox - Side rolls upwards downwards movements are hydraulic powered Options: - variable speed of rotation EURO 4.682,-- - metarial feeding table on request - oil coiler EURO 1.040,-- - center support EURO 8.250,-- - side supports EURO 6.600,-- We have many references!

Condition: used, Year of construction: 2007, pipe diameter (max.): 35 mm, overall weight: 2,700 kg, total length: 2,400 mm, total width: 1,400 mm, total height: 2,000 mm, Tube forming machine Brand: BLM Model: TUBE-FORM Year: 2007 Serial number: 415050200004 Weight: 2700kg Power: 12KVA Three-phase 380V Dimensions: 2400x1400x2000(h)mm Maximum tube diameter: 35mm Gisdpfx Asx Tt H Rjbdel Pushing force: 3.5t Clamping force: 5t Max. working stroke: 130mm

Condition: used, Hydraulic Guillotine Shear STEINER Type HTS 30/20 R Machine No. 315 Year of manufacture: 1982 Cutting length: 3050 mm Cutting thickness: 20 mm Backgauge: 800 mm, motorized control Motor power: approx. 30 kW Power supply: 400 Volt, 50 Hz - Backgauge with ELGO position control - Backgauge adjustment via ball screw spindles - SICK safety light curtain at the front for access protection - 3 material support arms with ball rollers - Electric foot switch Gijdpfx Aod Hxx Aobdsl - Spare blade - Oil cooler with air heat exchanger - Extremely heavy-duty machine in very robust construction Base machine dimensions L x W x H: 4650 x 2610 x 3200 mm Base machine weight: 27,000 kg Transport space required (base machine) L x W x H: 4650 x 2610 x 3200 mm Transport space required (additional) L x W x H: 3500 x 2450 x 1400 mm Total weight: 27,000 kg Good condition Machine can be inspected at our warehouse in 37235 Hessisch Lichtenau. Test cuts possible.

Condition: new, sheet width 1050 mm plate thickness 3.3 mm pre-bending 3.0 mm roll length 1050 mm roll diameter 90.0 mm min. dia. 130 mm engine output 1.10 kW weight 570 kg range L-W-H 1.800 x 800 x 1.130 mm Furnishing: - Robust electro-mechanical bending machine - 2x central rollers driven by an electric motor (top and bottom roller) - Top roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - Lower roller manually adjustable, by hand wheel - asymmetrical roller arrangement - self-braking main motor - Safety device (safety line with switch unit) - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized side roller adjustment Gedow U U Udjpfx Abdsil - Digital position display for motor-driven adjustable side roller

Condition: used, Year of construction: 1991, weight of the machine ca. 1,5 t Giodpfjx Ni E Ijx Abdol ja

Condition: good (used), Bending tool, die, upper blade, upper tool, upper jaw -Bending tool: from Lotze HDZ swivel bending machine -Length 2678 mm Giedpfjip Eqrox Abdol -Hole spacing: 100 mm / M10 -Dimensions: see drawing in the photos -Dimensions: 2678/15/H57 mm -Total weight: 15.7 kg

Condition: new, sheet length: 3100sheet thickness: 13prebending: 10total power requirements: 15weight approx.: 10messurements (LxWxH): 4,88x1,16x1,18 Illustration Similar Roller diameter (top/bottom): Ø270 mm Bending length: 3,100 mm Maximum sheet thickness for normal bending: 13 mm Maximum sheet thickness for prebending: 10 mm Prebending / bending radius: 8 mm / 10 mm (radius calculated as Ød × 1.5) CE Standard Variable speed Control unit – 7 Touch Screen Conical bending Induction hardened rolls Side rolls positioning via electronically synchronized PLC Bottom roll rigid mechanically synchronized Safety mechanism for welding on the machine Stress-relieved steel construction body Rolls seated with bearings Top roll hydraulic opening Top and bottom rolls driven by hydraulic motor and planetary gearbox Electrical and hydraulic overload protection Hydraulic pressure adjustable bottom rolls Giodpfx Abed Ab H Eodol

Condition: good (used), Technical data: Working length: 2050 mm Giedpfoxruvzjx Abdol Max. bending capacity: 18.0 mm Pre-bending: 12.0 mm Top roller diameter: 280 mm Bottom roller diameter: 280 mm Conical bending device Hydraulic drop-end bearing Motor power: 7.5 kW Dimensions (length x width x height): approx. 3650 x 1550 x 1650 mm Weight: approx. 7.5 tonnes The seller is not liable for typing or data transmission errors. The machine's condition in appearance, technology, and wear corresponds to its age; used machines are sold without any guarantee.

Condition: good (used), Bending tool, die, lower knife, lower tool, lower jaw -Bending tool: from Lotze HDZK swivel bending machine -Widthen: for lower cheek -Dimensions: 2487 x 100 x 15 mm / 190 x 100 x 15 mm -Hole spacing: 100 x 18 mm Gjdpoip Eqkofx Abdeil -Transport dimensions: 2487/100/H30 mm -Total weight: 29.4 kg

Condition: excellent (used), Year of construction: 2006, Technical Data: Gsdpfsx Dtt Aex Abdjil Working width: 2100 mm Bending capacity: 20.0 mm Pre-bending: 15.0 mm CNC control Upper roller diameter: 350 mm Middle roller diameter: 330 mm Side rollers diameter: 240 mm Hardened rollers Conical bending device by tilting both side rollers Mobile control panel with digital display Motor power: 7.5 kW CE marking Dimensions (L x W x H): approx. 3600 x 1500 x 1500 mm Weight: approx. 4.5 t The seller is not liable for typing or data transmission errors. The machine is in appearance, technology, and wear condition appropriate for its age; used machines are sold without any warranty.