Used Kempak 200 Tig for sale (16,921)

Condition: excellent (used), CTS Type: TSS-70/130 Water-cooled refrigeration unit For sale is a high-quality thermal shock test chamber by CTS (Clima Temperatur Systeme), model TSS-70/130. This device is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance. Application Areas: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical Specifications: Type: TSS-70/130 Test volume: 130 liters Temperature range: - Hot chamber: +50°C to +200°C - Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from ambient temperature to +180°C Cooling rate: approx. 4 K/min from ambient temperature to -60°C Temperature deviation: - ±1 K over time - ±2 K spatially Temperature change rate: - max. 100 K/min average for shock test mode (no radiant heat) Transfer time between chambers: - ≤ 15 min for -65°C to +200°C with 10 kg ICs Changeover time: - < 10 seconds Electrical Specifications: Connection: 400 V, 3/N, 50 Hz Nominal power: approx. 17.2 kW Nominal current: approx. 29 A Site fuse: 32 A slow-blow Connection: Cekon 32 Refrigeration System: Refrigerant: R404A / R23 Water-cooled, low noise, fully hermetic Features/Equipment: - CTS control panel - Microprocessor-controlled regulation and monitoring system - Programmable operation (up to 100 test programs) - Digital setpoint and actual value display - RS232 interface - 2 free switching channels for external device control - Fault notification via volt-free contact (Loadable up to 30 V DC, 2 A) - EMC tested Technical Construction: - Hot and cold chambers - Transfer basket with spindle drive - Test chamber/transfer basket made of stainless steel (material no. 1.4301) - Stainless steel wire insert basket - Tube port NW 50 with sealing plug - Compressed air connection 1/4" male - Non-pressurized condensate drain R 1/2" female thread - Safety door locking - Lockable door with window Bjdsy Hkd Hjpfx Ab Djll Dimensions (according to installation diagram): External dimensions approx.: 2335 x 940 x 1820 mm Installation clearance approx.: 1990 x 940 x 1652 mm Test chamber internal dimensions: height approx. 410 mm, width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Additional Data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh Important information for your safety as a buyer! The following points are performed on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If required, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented test run. Condition: used Scope of delivery: see photos (Specifications subject to change and errors excepted.) For further questions, please feel free to contact us by phone.

Condition: good (used), Mounting plate, scribing plate, measuring plate, measuring table, straightening plate, scribing plate, test plate, inspection plate, precision measuring table Bodpfezldm Nox Ab Dell -Mounting plate: Test plate with support ribs -Clamping surface: 300 x 200 mm -Sheet thickness: 10 mm -Plate: with supporting ribs -Transport dimensions: 446/200/H74 mm -Weight: 11 kg

Condition: new, new ! Bjdpfxezi Sdqj Ab Djll all stainless steel closed lid with seal 2 mixing directions (manual or automatic) tiltable CE-approved power : 2,2 kW overall dimensions (l x w x h) : ± 1.300 x 600 x 1.300 mm The Barmix 200 liter paddle mixer is an ideal machine for mixing all types of food products within the meat, poultry, fish, vegetables, dairy, cereal, confectionery, petfood and sandwich filling industry. Mixing for meat and vegetarian burgers, sausages, meatballs, coleslaw, potato salad and other wet salads, mash potato, vegetables fresh and frozen, cereals, raw petfood Also suitable for dry products, such as herbs, ingredients, powders, granules, nuts, grains, seeds, kernels, dried fruit, Granola, etc.

Condition: excellent (used), Weiss Type: SWT 200/400 Weiss spray and splash water test cabinet This cabinet is used to test the ingress of water into enclosures. In conjunction with a timer, the test cycle can be automated with an adjustable test time from 3 seconds to 30 hours. Complies with DIN VDE 0470 T1 or EN 60529 for tests according to protection classes IPX3 and IPX4. The integrated circulation system can reduce water consumption to a minimum. Features Glass door with wiper Pneumatic drive of the swivel nozzle Adjustable swivel angle Replaceable swivel nozzles Nozzle holder swivels and is replaceable Adjustable water flow rate and measurement Control of the test duration Data for mechanical stress Max. load with test specimen (evenly distributed over the area) Permissible test specimen weight for the test specimen holder (total) 25 kg Blodpfxszh D Rmo Ab Dol Spray radius 200 mm / 400 mm Data for IP protection class tests Swivel speed approx. 60°/s Swivel angle IPX3 approx. ± 60° Swivel angle IPX4 approx. ± 180° -10° Dimensions: External dimensions with control cabinet (D x W x H) approx. 1000 x 1350 x 1,900 mm External (D x W x H) approx. 1000 x 1000 x 1,900 mm Internal dimensions (D x W x H) 400 x 650 x 750 mm Operating data Voltage: 3/N/PE AC 400V ±10% 50Hz Rated power 1.5 kW Rated current 6.0 A Weight: 375 kg Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by telephone.

Condition: excellent (used), Espec Type: TSA-202E-W Temperature shock chamber, water-cooled Cold chamber: -55°C to 0°C Hot chamber: +50°C to 200°C System: Two-zone testing via damper control Temperature fluctuation: ±0.5°C Hot chamber: Temperature: Heating time: from ambient temperature (20°C) to +200°C within 15 minutes. Cold chamber: Temperature: Cooling time: from ambient temperature (20°C) to -55°C within 35 minutes. Temperature: Recovery time: within 5 minutes. Internal dimensions (W x H x D mm): 650 x 460 x 670 External dimensions (W x H x D mm): 1550 x 1900 x 1670 Approx. 200 liters Power supply: 400 V AC 50Hz: 65 A Refrigerant: R404A 5 kg, R23 2.0 kg Weight: approx. 1200 kg For your safety as a buyer, please note the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refilling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Blodpfx Abezh Htks Dol Condition: used Scope of supply: (See picture) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: new, functionality: fully functional, empty load weight: 128 kg, maximum load weight: 622 kg, overall weight: 750 kg, axle configuration: 1 axle, loading space length: 2,010 mm, loading space width: 1,067 mm, loading space height: 400 mm, total length: 2,910 mm, total width: 1,500 mm, total height: 900 mm, maximum speed: 100 km/h, trailer brake: trailer unbraked, Year of construction: 2026, Martz HIT 200 Tipper NEW VEHICLE Internal dimensions: 201 cm x 106 cm Gross weight: 750 kg Payload: 622 kg Side wall height: 40 cm Unbraked single-axle low-bed trailer Removable side walls made of galvanized steel sheet Rear and front panels foldable and removable Easily convertible to a flatbed transport platform Bolted and galvanized steel frame Folding drawbar Phenolic plywood floor 13-pin electrical system Rear lights with reversing light, fog light, and triangular reflectors Plastic fenders Jockey wheel 13-inch M+S tires The trailer can be stored vertically on the rear panel when not in use Optional accessories: - 100 km/h upgrade - Rear support stands - Mesh sides - Side extension panels 40 cm - Aluminum lid with holder (e.g., for bicycle carriers) - Flat tarpaulin with or without bows - High tarpaulin 80 cm - Coarse or fine mesh net - Spare wheel with holder - Loading ramps Additional accessories available on request! Images are for illustration purposes and may show optional equipment subject to extra charge. Plus vehicle registration documents and shipping to Gera €100 net Haven't found the right trailer yet? Blodpfx Aey Dq Dheb Dol We always have 50-100 vehicles in stock and ready for immediate pickup. The workshop is open on weekdays from 8:00 to 17:00 for all types of repairs. Specialist in axle repairs, including for caravan trailers. Large selection of rental trailers. We also offer a wide range of spare parts and accessories for trailers of all manufacturers. Get expert advice by phone, visit our website, or stop by in person.

Condition: good (used), Year of construction: 2007, Ref. no.: 18597 Manufacturer: ENGEL Type: insert 200 H/70 CC 200 Year of construction: 2007 Clamping unit Clamping force: 70 ton Opening stroke: 305 mm Injection unit Screw diameter: 25 mm Injection volume: 69 cm³ Shot weight: 62 g Injection pressure: 2381 bar Measurements and weight Dimensions: 4,0 x 1,8 x 2,5 m Machine weight: 5600 kg Further information: The ENGEL INSERT 200H/70 is a professional vertical injection moulding machine specially designed for insert molding and precision technical plastic applications. Built with ENGEL’s compact and robust machine concept, this model has been widely used for many years in the automotive, electronics, cable technology and technical plastics industries. One of the major advantages of this machine is its rotary table system. This design allows the operator to load inserts on one side while production continues on the other side. As a result, cycle times are reduced and production becomes safer and more efficient. This system is especially advantageous for manufacturing metal insert parts, connectors, cable components and precision technical products. Compared to conventional horizontal injection moulding machines, the ENGEL INSERT series offers a much more ergonomic and controlled process for insert placement. Thanks to the vertical clamping system, inserts remain stable inside the mould, enabling highly precise production results. The ENGEL control system used on this machine is known for stable process management and reliable operation. Its user-friendly interface allows easy handling in daily production. The machine has approximately 51,944 operating hours and was reportedly in running condition until removed from production. The overall condition of the machine is clean and well maintained. The electrical cabinet is tidy and the mechanical components appear to be in good condition. Bedpfx Aoy Au I Uob Dell The ENGEL INSERT series is particularly suitable for: * insert molding applications * metal/plastic combination parts * electronic component production * connector and cable technology * technical plastic parts * precision industrial products With its robust mechanical construction, compact design and professional production capabilities, the ENGEL INSERT 200H/70 represents a reliable and long-lasting production solution for technical plastic manufacturers.

Condition: excellent (used), Type: SWT 200/400-S Weiss Spray and Splash Water Test Cabinet Used to test water ingress into enclosures. In combination with a timer, the test cycle can be automated with an adjustable test duration from 3 seconds to 30 hours. Complies with DIN VDE 0470 T1 and EN 60529 for tests according to protection classes IPX3 and IPX4. The integrated recirculation system reduces water consumption to a minimum. Features - Glass door with wiper - Pneumatic drive for the oscillating pipe - Adjustable oscillation angle - Interchangeable oscillating pipes - Swivel and interchangeable nozzle holders - Adjustable and measurable water flow rate - Test duration control Data for mechanical load: - Max. load with test specimens (evenly distributed): Permissible total weight for specimen carrier: 25 kg - Spray radius: 200 mm / 400 mm Data for IP protection class tests - Oscillation speed approx. 60°/s - Oscillation angle IPX3 approx. ±60° - Oscillation angle IPX4 approx. ±180° -10° Dimensions: - External dimensions with control cabinet (D x W x H): approx. 1000 x 1350 x 1900 mm - External dimensions (D x W x H): approx. 1000 x 1000 x 1900 mm - Internal dimensions (D x W x H): 400 x 650 x 750 mm Bljdpfx Abozii Ako Djl Operating data: - Voltage: 3/N/PE AC 400V ±10% 50Hz - Rated power: 1.5 kW - Rated current: 6.0 A - Weight: 375 kg Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of delivery: (See picture) (Technical data subject to change and errors excepted!) Further questions can be answered by phone.

Year of construction: 2026, condition: used, New: Yes Empty weight: 400 kg Dimensions of cargo space: 150 x 130 x 107 cm CE mark: yes Please contact Team DPX for more information AC400V-200kW Automatic Load Bank Rated Voltage: 3P4W AC400V 50/60 Hz Rated Voltage & Frequency: 400VAC; 3 phase 4 wire, 50/60 Hz Power Supply: 3P5W AC400V 50 Hz Rated Power: 200 kW at 400V Duty Cycle: Continuois Cooling Type: Forced Air Cooling (Horizontal air intake and exhaust cooling, there will be louver at air outlet and inlet.) Load Steps: Resistive Load: 9 steps, 1, 2, 2, 5, 10, 10, 20, 50, 100 kW Wire Connection: - Load bank input— busbar (star coupling “Y”) - Control power input—terminal block Communication Interface: RS232/RS485 Bledpfsznr Dbex Ab Dol

Condition: used, Year of construction: 2012, fuel type: diesel, Lifting capacity: 230 kg Bsdpfx Aezqkatob Dell Please contact Gebrauchtgeräte Center for more information

Condition: used, Year of construction: 1996, turning diameter 600 mm turning length 850 mm swing diameter over bed slide 434 mm Control Siemens Sinumerik 840D total power requirement 54 kW weight of the machine ca. 10 t dimensions of the machine ca. 6000x2800 mm Spindle speed (max): approx. 0–4500 rpm Spindle speed (max): approx. 0–4500 rpm Spindle bore: approx. 65 mm Blsdpfszrzxiex Ab Dol Spindle taper: mostly DIN 55026 A6 / ISO taper X-axis travel: approx. 220 mm Z-axis travel: approx. 950 mm Feed rate: approx. 25 m/min Tools & equipment Tool turret: usually 2 turrets with ~12 tool positions Powered tools: possible depending on equipment Tailstock: optional, often NC-controlled (SK30)

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 15 h, functionality: fully functional, machine/vehicle number: ET.200.01.2025, overall weight: 134 kg, input voltage: 220 V, input current: 21 A, type of input current: AC, warranty duration: 24 months, Equipment: documentation/manual, METALSELF ET-200 Automatic Orbital Welder + EC-120 Welding Head Ex-Demo (-40%) DESCRIPTION: Bljdpfozw Uh Uox Ab Djl MACHINE CONDITION: We offer for immediate delivery a Metalself orbital TIG welding system consisting of an ET-200 power source and an EC-120 closed-chamber welding head. The machine (manufactured in 2025) is in LIKE-NEW condition: it has never been used in production and was used exclusively as an internal demonstration unit. Due to its "Ex-Demo" status, the entire system is offered with an exceptional 40% discount on the list price. SYSTEM OVERVIEW: The system automates TIG welding on thin-walled pipes, performing a complete 360° rotation around the joint. It is the ultimate solution for industrial piping, fluid, food, and pharmaceutical systems, ensuring perfect repeatability, impeccable aesthetics, and weld seams free of defects. POWER SOURCE SPECIFICATIONS (ET-200): -Technology: Microprocessor-controlled inverter for millimeter-precise arc control. -Welding current: 5 ~ 200 A. Modes: Direct Current (DC) and Pulsed, ideal for thermal control on stainless steel and titanium. -Interface: Intuitive touch screen with an "Auto Prog" system that automatically generates parameters by simply entering the tube diameter and thickness. -Capacity to store 200 programs. Cooling: Integrated water circulation system. Quality Control: Integrated thermal printer on the machine and USB port for exporting welding reports. -Power supply: 220VAC ±10% - 50/60 Hz (Consumption 4.5 KVA). -Dimensions and Weight: 500 x 380 x 300 mm; 28 kg. WELDING HEAD SPECIFICATIONS (EC-120): -Type: Orbital welding head with closed chamber. -Operating diameter range: from Ø 19 mm to Ø 114.3 mm. -Maximum penetration thickness: ≤ 3 mm. -Shielding gas: Argon. -Cooling: Water-cooled. -Welding head dimensions: 540 x 195 x 54 mm. -Welding head weight: 6.5 kg. THE SUPPLY INCLUDES: -ET-200 power source and EC-120 welding head. -Dedicated trolley for easy and safe movement of the system in the workshop. -Power cables, control connections, ground clamp, and hydraulic/gas tubing. -CE Declaration of Conformity. -Complete user and maintenance manual (including parts list and programming instructions). SALE CONDITIONS: -Price: -40% compared to the new list price. -Delivery: Ex Works (EXW) in Settimo Torinese. -Availability: Immediate. The machine can be viewed at our facility and is available for any testing or practical demonstration.

Condition: reconditioned (used), Year of construction: 2025, briquette diameter: 100 mm, Equipment: cooling unit, emergency stop, Briquette press Di Più MB100 – Year of manufacture 2009 – Complete system with saws & accessories (Overhauled in 2026!) Briquette press Pawert SPM I-90/200 Overhauled in 2025 (Like new!) For sale are briquette presses of the type Di Più MB100, year of manufacture 2009 (overhauled in 2025/26), including saws, conveying equipment, and other accessories. The machines come from industrial use and are ideal for the production of wood briquettes from sawdust, wood chips, and wood residues. --- Technical data (per machine): Type: Di Più BRIK MB100 Year of manufacture: 2009 Briquette diameter: approx. 90 – 110 mm Production capacity: approx. 1,300 – 2,300 kg/h Press pressure: approx. 2,000 – 2,500 kg/cm² Main motor: 75 kW Total power: approx. 98 kW Material moisture: optimal 8 – 12 % Particle size: approx. 1 – 12 mm Weight: approx. 7,800 kg per machine Drive: hydraulic ram press --- Equipment: Material hopper Conveying screws Hydraulic system Bjdozw T Dzspfx Ab Dell Control cabinets Saws for cutting briquettes to length Protective covers & safety systems Discharge units --- Scope of delivery: 3 complete Di Più MB100 briquette presses Saws Conveying equipment & accessories Spare parts upon request --- Application areas: Sawmills Wood processing industry Biomass plants Briquette production for energy & sale Location: on request Transport: Organization possible by agreement Price: on request Individual sale or complete package possible

Condition: new, Hello, I would like to offer high-pressure KSB pumps with ABB electric motors. Applications for the pumps: - Chemical industry - Fuel industry - Gas industry - Paper industry I have various models available: - 5 units: MCPK150-125-200 VX LXM - 5 units: MCPK065-040-200 VC EXM Bsdpfxjzx Upzs Ab Djll - 2 units: MCPK100-065-200 VC LXM - 2 units: MCPK080-050-315 VC EXM The stated price is for 1 complete pump with motor, model MCPK150-125-200 VX LXM. If you are interested in a different pump model, please contact me.

Year of construction: 2009, condition: ready for operation (used), Throughput: approx. 150 jars/min, foreign body detection capability for glass fragments: from approx. 3 x 3 x 3mm, metal: from approx. 1 x 1 x 1mm, stones and bones: from approx. 3 x 3 x 3mm, suitable for glass containers, tinplate cans, beverage cartons (carton bricks), and plastic containers, typical false rejection rate per 10,000 inspected products: approx. 7, maximum container diameter: 155mm, maximum inspection speed: 100m/min, standard sensor speed: 45m/min, sensor height: 256 to 410mm, pixel size: 0.4 x 0.4 to 0.8 x 0.8mm, rejection system: electropneumatic cylinder, operator interface: 17 inch touchscreen, remote access: Ethernet or modem, frame material: AISI 304 stainless steel, sensor protection class: IP55, power supply: 3 phase + protective earth (3PH + GND), operating voltage: 400V, machine power consumption (2 motors): 3kW, processing unit power consumption: 500W, high voltage generator: 0.3 to 1kW, electrical cabinet protection class: IP55, X-ray radiation: 0.1µSv/h, compressed air operating pressure: 4 to 6bar, air consumption: 50Nl/min, infeed and outfeed height: 1305mm, screen and operating height: 1070mm, length: 2890mm, width: 1000mm, height: 2525mm, weight: 1.3t. Equipped with a reject system for contaminated containers and a conveyor belt. The machine was in operation until 2024. Inspection on site is possible. Bjdpfx Abszhw S Re Doll

Year of construction: 2001, condition: ready for operation (used), A hydraulic CNC press brake Hämmerle (M+S Brugg AG) is available. Press force: 2000kN, max. working length: 3100mm, max. stroke: 400mm, max. throat depth: 250mm, frame distance: 3240mm, max. opening width: 965mm, max. sheet thickness: 8mm. Machine dimensions X/Y/Z: approx. 4400mm/2700mm/3400mm, weight: approx. 16600kg, control system: CNC Infinitron. Documentation available. An on-site inspection is possible. Bljdpfezcyq Tjx Ab Dol

Year of construction: 2024, condition: ready for operation (used), An almost like-new and high-precision CNC centerless grinding machine Monzesi is available. Grinding wheel outer diameter min./max.: 406mm/280mm, inner diameter: 152mm, max. width: 200mm, speed: 2100rpm, power: 11kW. Regulating wheel outer diameter min./max.: 160mm/254mm, inner diameter: 115mm, max. width: 200mm, speed: 285rpm. Workpiece diameter: 100mm, workpiece length: 200mm, regulating wheel axial adjustment: +/-10mm, taper setting: -2°/6°, tilt adjustment: +/-5°, accuracy: 0.0001mm. Machine dimensions X/Y/Z: approx. 3800mm/2000mm/21500mm, weight: approx. 4500kg, control: CNC Fanuc 35i-B Digital, operating hours April/2026: 481h. Documentation available. An on-site inspection is possible. Expected to be available from end of July/August 2026. Blsdpoyyb Tlsfx Ab Dsl

Year of construction: 1992, condition: ready for operation (used), Working length: 4300mm, pressing force: 2000kN, connected load: 15kW, weight: 18t, including tools. Bedji Dx Sbspfx Ab Dsll

Condition: ready for operation (used), Year of construction: 1989, An aluminum die casting system is available. Clamping force: 2200kN, opening force: 71kN, max. opening stroke: 430mm, mold closure: double toggle lever, pressure chamber: cold chamber, position: horizontal. Filling piston diameter min./max.: 40mm/70mm, pressure chamber filling volume min./max.: 293cm³/898cm³, casting pressure: 1990bar, blast area min./max.: 110cm²/338cm², output: 780 cycles/h. Clamping plate dimensions X/Y: 755mm/755mm, column spacing: 500mm/500mm, mold height min./max.: 250mm/600mm, min. mold dimensions X/Y: 296mm/296mm. Including crucible furnace, blow-out device, automatic dosing unit and 4x control cabinets. Documentation available. Bedjucfwpepfx Ab Djll

Year of construction: 1999, condition: ready for operation (used), Ejector stroke: 180mm, ejector force: 44kN, nozzle contact pressure: 38kN, hopper capacity: 75dm³, mold clamping force: 1962kN, mold opening stroke: 560mm, length: 6275mm, width: 1520mm, height: 1965mm, weight: 8.3t. An inspection on site is possible. Blsdpfey Sncqox Ab Dsl

Year of construction: 2009, condition: ready for operation (used), Clamping force: 2000kN, locking force: 2200kN, max. opening stroke: 570mm, min. mould installation height: 310mm, max. mould installation height: 660mm, max. distance between mould platens: 1230mm, mould platen dimensions: 830x830mm, distance between tie bars: 560x560mm, max. mould weight: 3.3t, max. weight on moving mould platen: 1.7t, max. weight on fixed mould platen: 2.5t, ejector stroke: 180mm, ejector force: 69kN, ejector return force: 31kN, screw diameter: 45mm, L/D ratio: 20, injection pressure at 400°C: 2402bar, shot volume: 358cm³, shot weight (PS): 330g, max. metering stroke: 225mm, max. nozzle stroke: 400mm, nozzle immersion depth (SVO): 20mm, nozzle contact force: 80kN, installed barrel heating capacity: 13kW, material hopper capacity: 70l, oil tank capacity: 500l, screw drive: 32kW, clamping unit drive: 32kW, pump unit power: 15kW, total installed power: 92kW, continuous sound pressure level: 74dB(A), length: 5700mm, width: 1700mm, height: 2200mm, weight: 11t, operating hours according to PLC: 36,734h, barrel heating: 25,665h, pump: 18,222h, documentation available. An on-site inspection is possible. A Wittmann robotic cell is also optionally available. Bledpfx Absy Tx Rbo Dol

Year of construction: 2023, condition: ready for operation (used), An unused Traub CNC twin-spindle turning and milling center with peripheral equipment is available. Spindle types 1/2: D76/D76, max. turning length: 900mm, max. workpiece diameter: 76mm, number of tool carriers: 3, control system: Traub TX8i-s V8. Main spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Counter spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Upper tool carrier: axes: X/Y/Z, stations: 12. Lower left tool carrier: axes: X/Y/Z, stations: 12. Lower right tool carrier: axes: X/Y/Z, stations: 12. Including Isi Elbaron RON4DHEC mist extraction and filtration system, custom-built circulation conveyor, Bürener hinged belt chip conveyor, Bürener Eco-Fluid coolant system (600l), cooling unit, coolant chiller, Traub WH workpiece handling system, various grippers and gripper pairs, IoT, and management and monitoring software. This machine was never put into operation and is therefore in as-new condition. Documentation available. An on-site inspection is possible. Bsdpfxezkvkqs Ab Doll

Condition: good (used), Deburring machine, pipe deburrer, bore deburrer, deburring device, brush deburring machine, wire brush Bodpfx Abjrw Daao Dsll -Manufacturer: Keil, Keil-Single deburring machine with base -Drive: 3.0/2.0 kW / 3000/1500 rpm -Brush: Ø 200 mm, Ø 200-250-300 mm possible -Brush width: 60 mm, 20-40-60-80-100 possible -Dimensions: 800/800/H1210 mm -Weight: 110 kg

Condition: used, Surface grinding machine, grinding machine, surface grinding machine-horizontal, surface grinding machine, magnetic grinding machine Blsdpfjt N Adbsx Ab Del -Manufacturer: Blohm, surface grinding machine-horizontal -Table size: 770 x 140 mm, swiveling -Travel paths: x 490 mm / y 200 mm / z 220 mm -Dimensions: 1030/870/H1510mm -Total weight: 403 kg

Condition: good (used), Year of construction: 2001, Machine is in good condition. Blsdpferpk Rmex Ab Djl Parts shown by hand not come. Cutting tools not come.