Used Linear Feed for sale (13,005)

Condition: like new (used), Chain feed table, used for feeding and linear transportation of roll goods or log goods. Forward/reverse run (reversing circuit) integrated, end positions are queried via roller limit switches. Feeding length: 2200mm Feeding height: 950mm (adjustable) Drive power: 0.18kW (Getriebebau Nord) Kwedetw Sm Nspfx Ahzjt Condition: slight paint wear, otherwise as good as new

Condition: used, Vibratory bowl feeder / sorting device / bowl feeder / vibratory feeder RNA Vibratory bowl feeder, sorting device / screw feeder with vibratory feeder for screwdriving technology Feeding system, feeding device Manufacturer: RNA Rhein-Nadel Automation GmbH Type: SRC-N 250-2L Ser.- No.: 03611 Year of construction: approx. 2000 Cup diameter bottom: 300 mm Pot diameter top: 350 mm Inner pot height: approx. 25 mm Sorting track width: approx. 30 mm Total height (drive + bowl with sorting track): 380 mm Vibration frequency: 100 Hz / 6000 min-1 Mains connection: 230 Volt, 50 Hz - The conveyor was used for feeding automotive fuses Space requirement: Ø x H: 420 x 390 mm Weight of bowl feeder: 52 kg Linear conveyor / vibratory conveyor / sorting device Manufacturer: RNA Rhein-Nadel Automation GmbH Type: SLL 400-400 Ser. No. 00835 Year of construction: approx. 2000 Maximum rail length: 700 mm Usable weight: approx. 1.5 to 2 kg Vibration frequency: 100 Hz / 6000 min-1 Mains connection: 220 Volt, 50 Hz - Swing plate L x W x H 400 x 65 x 12 mm - Mounted track length 530 mm - Height with oscillating plate 145 mm Space requirement: L x W x H: 580 x 120 x 400 mm Weight of linear feeder: 20 kg Control unit for vibratory drives, control unit, controller, control system for vibratory conveyors / sorting device / bowl feeder / vibrating bowl / vibratory feeder Manufacturer: RNA Rhein-Nadel Automation GmbH Type: ESK-N80 / ESG 90 Mains connection: 0 ... 208 Veff; (230VAC in motor operation) at 230V mains voltage 0 ... 98Vrms; (115VAC in motor mode) at 115V mains voltage Output voltage: 0...208 V (rms) adjustable, (230 V mains) Number of power outputs: 2 Output 1: Circular conveyor, linear conveyor max. 10A adjustable Output 2: Circular conveyor, linear feeder max. 6 A adjustable Total load current: 16 Aeff Sensor inputs: 1 Kwjdpjuzn Nnsfx Ahzst Number of enable inputs: 1 (24V DC) Sensor supply: 24V DC, max 60 mA Sensor delay ON: 0 ... 8 sec. Sensor delay DOWN: 0 ... 8 sec. Power output connection: Hirschmann 7 pol. - Two power outputs - Sensor amplifier with independently adjustable time stages (On / Off) - Soft start (internally adjustable) - External enable input 24VDC Space requirement: L x W x H: 260 x 190 x 140 mm Control unit weight: 3.6 kg All devices tested and in good condition

Condition: ready for operation (used), controller model: Fanuc 310i, empty load weight: 10,000 kg, total length: 4,500 mm, total width: 1,990 mm, total height: 2,300 mm, swing diameter over cross slide: 950 mm, Spindle 1: 20 kW - 5000 rpm - spindlebore: 70 mm Turret 1: 12 driven tools - 2,5 kW - 4000 rpm Driven C-axis X1 movement: 165 mm Y1 movement: +50/-30 mm Z1 movement: 678 mm Spindle 2: 17 kW - 5000 rpm - spindlbore: 42 mm Turret 2: 12 driven tools - 2,5 kW - 4000 rpm Driven A-axis X2 movement: 165 mm Z2 movement: 640 mm Iemca Master 880 P barfeeder Dia of spindle bore: 70 & 42 mm Power on the spindle: 20 & 17 kW Kjdpov Rwltefx Ahzjwt Number of speeds: 5000 rpm Chuck: Ø 175 mm Toolchanger: yes (2x) Number of tools: 12 tools (2x)

Year of construction: 2012, condition: good (used), Linear feeder of the company Wolfgang Hörmle. Kedpfx Ajif D Nzehzowt In good condition for sale. Manufacturer: Hörmle Type: KF 07-1 Voltage: 220 V Conveying length: 380 mm Height: 150 mm

Condition: used, Linear feeder / Vibratory feeder / Sorting device Vibratory linear feeder, vibratory hopper, dosing hopper, storage hopper Vibratory bowl feeder, bowl feeder Vibratory bowl, screw feeding system with vibratory feeder for screwdriving technology Feeding system, feed unit Manufacturer: RNA Rhein-Nadel Automation GmbH Year of manufacture: approx. 2000 Useful load: approx. 1.5 kg Oscillation frequency: 100 Hz / 6000 rpm Mains connection: 220 Volt, 50 Hz - Oscillating plate L x W = 170 x 60 x 12 mm - Mounted track length 340 mm - Overall height with base plate and oscillating plate approx. 115 mm Required space L x W x H: 400 x 280 x 400 mm Weight: 9 kg Kwjdoxf Urvepfx Ahzot Good condition

Condition: excellent (used), Year of construction: 2008, DMG CTX 510 Kjdpfx Aor Ak S Nehzowt Sinumerik 840D Machine in perfect condition, equipped with bar feeder and C axis Spindle operating hours: 6720 Spindle bore: 95 mm Collet chuck Forkardt D=100 mm max; I also have a brand new Hainbuch SK100 collet chuck for this machine Tool holder VDI 40

Condition: good (used), A good used linear weigher with Digiway controls - this machine is a single head weigher with 4 vibratory feed trays - loadcell technology and Digiway controls for fast accurate weighing and filling or granular free flowing products. Kwodpfju U Ai Hsx Ahzst

Condition: used, functionality: fully functional, Hoerbiger Origa P120S-25 Linear actuator. Kwjdpfx Ahetwqp Aezot Good working condition. Please check out our other listings as well.

Condition: used, functionality: fully functional, Koganei ORGA40X2750 Linear actuator. Good working condition. Kodpetwqqgofx Ahzowt Please check out our other listings as well.

Year of construction: 2015, condition: excellent (used), Posiweigh Triple200 Three lane linear weighing line Kedpfx Ahjnl Em Rjzjwt Serial: 3054 2015, never been in production, weighing capacity up to 1000grams, suitable for dry, free flowing granular or piece type products, hopper capacity 120l, weighpan capacity 5l, two different discharge chutes for single drop of treble drop, comes with vibratory conveyor with 500kg hopper then feeds onto flighted elevator conveyor that feeds into the linear weigher and finally discharges onto a 3m indexing conveyor, supplied with a set of stainless steps, 1Ph

Year of construction: 2000, condition: used, machine/vehicle number: 000101-6, stainless vibratory feed conveyors, adjustable vibration for product control, on stainless frame. 1Ph. Kjdpodg H Ipofx Ahzswt

Condition: used, all stainless steel electrically heated, max. 280°C adjustable speed 11 inspection/cleaning hatches belt width ± 1.000 mm net length ± 7.500 mm with belt wash system outside dimensions (l x w x h) : ± 9.500 mm x 1.600 mm x 2.400 mm Modular construction system Conveyor belt (opening 13 mm) total power 224 kW heating steam pressure: min 3 bar 10 kg/h per valve max. 3 bar 140 kg/h per valve cooking time min/max : 4min 36sec-120min steam injection (to heat up and to improve product yield) Kwedpfx Ahoyaqh Rszot

Condition: good (used), Year of construction: 2006, functionality: fully functional, travel distance X-axis: 2,500 mm, travel distance Y-axis: 920 mm, travel distance Z-axis: 820 mm, controller manufacturer: Heidenhain, controller model: iTNC530, total height: 2,950 mm, total length: 6,000 mm, total width: 3,800 mm, table width: 900 mm, table length: 3,100 mm, rotational speed (min.): 20 rpm, rotational speed (max.): 18,000 rpm, overall weight: 25,000 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 18,000 rpm, coolant supply: 40 bar, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, X-axis travel: 2500 mm Y-axis travel: 920 mm Z-axis travel: 820 mm Table size: 3100 x 900 mm Spindle nose: SK/ISO40 Spindle speeds: 20 - 18.000 rpm Toolchanger: 30 pockets Controller: Heidenhain iTNC 530 Featured with: - Chipconveyor - Cooling through spindle 40 Bar - ISO40 tools - Machine manuals Country of origin: Germany Motor power: 35 KW Kedpfx Ahsyac Tljzjwt Machine LxWxH: 6000 x 3800 x 2950 mm Machine weight: 25.000 kg

Condition: good (used), Year of construction: 1996, Reel, unwind reel, motorized reel for sheet metal processing, motor reel, unwind reel, sheet metal unwinder, strip feeder, strip feeder for eccentric press, hydraulic press -Handover: in its current condition as inspected Kwedeitdikepfx Ahzst -Condition: without drive motor, without control unit, see photos -Manufacturer: Cisam Impianti, FEEDER belt feeding system -Type: 1000/2B -Passage: 395 mm -Transmission: Ratio 68.37:1, max. 251 Nm -Pneumatic cylinder contact force: 1.6 tons -Individual components: see photos -Dimensions: 1340/920/H1690 mm -Weight: 829 kg

Condition: new, FACTORY NEW ROTARY TABLES // ROTARY-SLIDE TABLES Positioning, simultaneous turning, and interpolation Rotary table sizes: 1,000 x 1,000 // 1,200 x 1,200 // 1,500 x 1,500 // 1,800 x 1,800 // 2,000 x 2,000 // 2,500 x 2,500 // 3,000 x 3,000 // 3,500 x 3,500 // 4,000 x 4,000 mm --- The clamping surface can also be round instead of square - Kedpfx Asm Tv Azjhzewt Maximum workpiece weight: 6,000 to 80,000 kg Optional sliding axis: 1,000 to 3,000 mm (in 500 mm increments) Positioning accuracy: ±5 arc seconds Only inquiries from Germany will be answered // Nur Anfragen aus Deutschland werden bearbeitet

Condition: used, clear span: 1,860 mm, total width: 11,720 mm, total height: 2,500 mm, Technical Data for Pallet Racking System: Racking System: Alser Type: NS Setup Specifications: Number of rack rows: 01 pcs Length per rack row: approx. 11,720 mm Number of bays per rack row: 06 pcs of 1,860 mm each Number of levels plus ground level: 02 pcs Volume Specifications: Pallet locations per bay: 06 pcs Pallet locations per row: 36 pcs Total pallet locations: 36 pcs Based on: Load carrier: Euro pallet EN 13698-1 Dimensions: 1,200 x 800 x 150 mm Total height incl. pallet: n.d. Max. pallet weight: approx. 1,000 kg Scope of delivery includes: 07x pallet racking uprights, used Material color: brown Profile dimension: C80 x 40 x 15 x 2.00 mm Including horizontal and diagonal braces, base plates Uprights are pre-assembled Max. bay load: 4,000 kg At buckle height: 1,250 mm (min. 5 bays per row) (welded truss) 2,500 mm high 1,050 mm deep 24x pallet racking beams, used Material color: orange Profile dimension: S 110 x 55 mm Beam type: B113 Connector: 2 HK Clear width: 1,860 mm Max. load per pair of beams: 2,000 kg, with evenly distributed load 48x safety pins, used Material finish: sendzimir galvanized For securing longitudinal beams against unintentional lifting 28x anchor bolts, new Manufacturer: Hilti Model: HST2 V3 M12x105 5-25 Design: Carbon steel, galvanized Approved for: cracked concrete 14x leveling plates, used Material: sendzimir galvanized Kedox Upqbjpfx Ahzjwt To level uprights set up on uneven ground 01x load plate with information on bay and shelf loads, manufacturer, and commission number Dimensions: 420 x 297 x 3 mm General Information about the Item: This item is offered for collection only. Any transportation or shipping of this item is subject to additional costs, which can be provided upon request depending on the delivery location and order volume.

Condition: good (used), Year of construction: 2008, operating hours: 72,899 h, functionality: fully functional, machine/vehicle number: 07510001241, turning length: 1,185 mm, turning diameter: 640 mm, spindle speed (max.): 12,000 rpm, workpiece weight (max.): 150 kg, total height: 3,040 mm, total length: 7,800 mm, total width: 4,100 mm, overall weight: 16,500 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D, DMG GILDEMEISTER GMX 250 LINEAR CNC Turning and Milling Center - Recorded spindle hours: 39,361 - Swing diameter: 640 mm - Counter spindle turning diameter: 400 mm - Spindle distance: 1,500 mm - X1 axis travel: 550 mm - Y1 axis travel: 180 mm - Z1 axis travel: 1,185 mm - B1 axis travel: 240° - X2 axis travel: 180 mm - Z2 axis travel: 1,050 mm - Z3 axis travel: 1,150 mm - Spindle speed range: 3,200/4,000 rpm - Rapid traverse rate, Slide 1 (X/Y/Z): 40/24/70 m/min - Rapid traverse rate, Slide 2 (X/Z): 24/36 m/min - Rapid traverse rate, Slide 3 (Z): 36 m/min Kjdoyaqczjpfx Ahzewt - Tool holder: HSK 63 - Spindle speed: 12,000 rpm - Number of tool stations in chain magazine: 40 stations - Incl. tool holders mounted on the turret - Incl. bar loader, manufacturer: COCCHE GIOVANNI, type: CNC-DB 110, year of manufacture: 2008, serial number: CNCDB-08.306, weight: 1,500 kg Note: The machine has the following defects: - The hydraulic unit is faulty – it needs to be repaired - The Q2 axis (milling spindle tool changer) fails frequently - X2 axis (guideways) moves slightly askew - The linear guides and drives show wear commensurate with age Attention: A vehicle with 3,000 mm transport width is required for transport! FCA D-58256 Ennepetal, loaded onto truck at a mutually agreed date at the end of February 2026.

Condition: excellent (used), Simodrive feed model Make Siemens Type 6 SC 6116 OAAOO G 600 D 490 / 49 M6 REQ Ksdpofhkt Rofx Ahzjwt Output current 60/120 A Space requirement :D. 290 x W.150 x H.480 mm Weight 13 kg

Condition: used, Year of construction: 2008, bar capacity 65 mm number of spindle speeds 5.000 U/min control Siemens 840 D no. of tools in turret 1 12 Kodpfexbtqisx Ahzswt no. of tools in turret 2 12 no. of tools in turret 3 12 Stk./pcs. tool taper VDI 30 driven tools turning speeds 4.000 U/min travel -x1 axis 165 mm travel -z1 axis 220 mm travel -x2 axis 165 mm travel -z2 axis 150 mm travel -x3 axis 165 mm travel -z3 axis 650 mm travel -y3 axis 80 (+50/-30) mm CNC Turning- and Milling Center | DMG - Sprint 65 linear equipped with main/counter spindle, a 3x turret for driven tools, bar feeder and chip conveyor as well as internal counter-spindle flushing with coolant. The machine is in a well-maintained condition and can be inspected at any time under power. The machine video from the production plant will be shared on request. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: Sprint65Gildemeister | Sprint-65 | Sprint65

Condition: used, Veneer press continuous press gluing press plate press Bürkle HSO 240/D 340/140 Press dimensions: 3400x1400mm Max discharge pressure 240T Max pressing pressure 6 kg/cm² Cylinders 8 pcs. with diameter 110mm Stroke 150mm Solid plates 40mm Water heated with boiler up to 60 degrees. Plates can be heated up to 150 degrees with the right boiler. Press dimensions: 2500x3900xH2800mm, 8500kg Input conveyor dimensions: 2200x3600mm, 500kg Documentation still available, first owner! Sold as one unit including conveyor belts - Details: - └ Description: The Omma glue roller is not available - Documentation available: No - CE certificate present: No - Max. workpiece length [mm]: 3400 - Max. workpiece width [mm]: 1400 - Material of press plates: Steel - Number of cylinders [pcs]: 8 - Total working pressure [ton]: 240 - Working pressure [kg/cm²]: 6 - Heating type: Water heated - Max. working temperature [°C]: 150 Financial information VAT: The price shown is exclusive of VAT Kedpfx Ahewng Tyozswt VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: ready for operation (used), Year of construction: 2002, spindle speed (max.): 4,500 rpm, travel distance X-axis: 260 mm, travel distance Y-axis: 40 mm, travel distance Z-axis: 635 mm, number of axes: 3, This 3-axis Gildemeister CTX 420 linear was manufactured in 2002. It features a max. travel in X-axis of 260 mm, Z-axis of 635 mm, and Y-axis of 40 mm. It handles a max. workpiece diameter of 680 mm and length of 760 mm. Spindle speeds reach up to 4,500 rpm. If you are looking to get high-quality turning capabilities, consider the Gildemeister CTX 420 linear machine we have for tact us for more information. Machine Benefits Kwodpfxoyar H Is Ahzst Technical Machine Benefits • Max. Workpiece diameter: 680 mm • Max. Workpiece length: 760 mm Extra Information Machine still under power

Condition: ready for operation (used), Year of construction: 2011, operating hours: 61,913 h, travel distance X-axis: 450 mm, travel distance Y-axis: 580 mm, travel distance Z-axis: 400 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, spindle speed (max.): 28,000 rpm, spindle motor power: 29,000 W, swivel angle C-axis (max.): 360 °, number of axes: 5, This DMG Mori HSC 55 linear Universal Machining Centre was manufactured in the year 2011 and has 61913 control hours, 59275 machines on hours, 10986 program run hours, and 10631 Spindle running time (spindle exchange at approx.7300 hours). The machine has a spindle speed of 20 - 28000 rpm and a capacity for 30 tools. It is equipped with a pallet changer, control is Heidenhain iTNC 530 control unit and has 5 axis. Machine Benefits Qualitative Machine Benefits Kwjdpox D Eqgofx Ahzot • The machine has capacity for 30 tools • Pallet changer Technical Machine Benefits • Measuring length: 400 x 400 mm • Axial run-out of the clamping surface Ø 350 mm • Axial stability of the work spindle: 0,005 mm • Spindle nose : 250 mm • Tool holder hsk-a63 according to din69893 • Pickup tool changer 16 places (chain) • Active cooling unit for main spindle and linear drives// active cooling unit for control cabinet • Direct absolute measuring system incl. Sealing air • Coolant/blast air changeover • Z-axis extension to z = 460mm Extra Information Machine still under power.

Condition: ready for operation (used), Feeding table Nordberg with Hopper Kwedpji A Aqgofx Ahzjt ding table: 5000 x 1100 mm Dim. Hopper: 5500 x 3700 x 2500 mm Driving: 22 kW E-motor

Condition: good (used), Year of construction: 2003, turning length: 1,505 mm, Turning & Milling Center GILDEMEISTER GMX 400 linear Year of manufacture: 2003 Control: Sinumerik Power line Technical Specifications: Main spindle drive power ISM 90: 36/45 kW (100/40%) Main spindle speed: Main spindle torque: Bar capacity: 90 mm Number of magazine positions: 120 pcs Milling spindle tool holder: HSK 63 Counter spindle drive power ISM 90: 36/45 kW (100/40%) Counter spindle speed: Counter spindle torque: Bar capacity: 90 mm B-axis / Milling spindle: Drive power: Speed: Torque: Tool holder: HSK z3 Lower turret: X-axis: Z-axis: Speed, driven tools: Number of turret stations: 12 pcs Tool holder: VDI 40 Accessories: - Chip conveyor - High-pressure unit with 20 bar - Preparation for 3D measuring probe - Tailstock function on counter spindle Kodpfowzbq Tsx Ahzjwt - Automatic sliding doors

Condition: excellent (used), Year of construction: 2017, operating hours: 20,000 h, functionality: fully functional, spindle speed (max.): 6,500 rpm, bar passage: 42 mm, bar diameter (max.): 42 mm, Production lathe Gildemeister Sprint 42 - 8 linear axes with high-pressure system and Iemca bar feeder Year of manufacture: 2017 Control: Fanuc 31i Operating hours: ~20,000h Version with 8 axes – linear drive on X1 axis Main and counter spindle speed: 6,500 rpm Max. bar capacity: 42mm Coolant system: Slide 1: 8 bar Slide 2 + Y: 20 bar Bar feeder: Iemca BOSS 552/32 Parts conveyor belt Kwodpfx Aexbpp Uehzet