Used Metal Material for sale (47,678)

Condition: used, Pay-off and take-up decoiler for coil material WANZKE CAMU Type SC 515/M Serial no. 8487 Year of manufacture: 2006 Coil weight approx. 1,500 kg Maximum coil width: 600 mm Coil inner diameter: 370 - 640 mm Maximum coil outer diameter: 1,800 mm Mandrel shaft diameter: 90 mm Distance from mandrel crown center to mandrel base: 950 mm Mandrel crown speed: 13 rpm Motor speed: 920 rpm Gearbox transmission ratio: 1:70 Mandrel drive motor power: 1.1 kW Power supply: 400 Volt, 50 Hz - Mechanical expansion of the mandrel crown with hand crank - Drive via geared motor with worm gearbox, directly mounted on the mandrel shaft Gedswvv Rqopfx Ag Njuh - Geared motor with electric brake - Mandrel shaft with mechanical slip clutch, pre-tensioned and adjustable via disc springs - Mandrel crown without strip travel arms - Without electrical control system and without loop switch Space requirement (L x W x H): 1300 x 800 x 1230 mm Weight: 380 kg Good condition

Condition: used, Strip Processing Line, Decoiler and Straightening Machine Year of manufacture: 1991 Strip width: 50 to 450 mm Sheet thickness with straightener inactive: 6 mm Sheet thickness with straightener active: 2 mm - Very well equipped with feed-in aids Required floor space for the entire line (L x W): approx. 7000 x 3000 mm Total weight: approx. 11 tons Good condition Straightening Machine HMS Type RS 47-04/1, Machine No. Strip width, nominal: 400 mm Strip width, max. pass-through: max. 455 mm Guedpeif Sg Ssfx Ag Njh Strip thickness at 400 mm width: max. 1.5 mm (steel) Strip thickness at 400 mm width: max. 2 mm (copper) Speed: max. 40 m/min Number of straightening rolls: 7 Straightening roll diameter: Ø 40 mm Number of pinch rolls: 2 Pinch roll diameter: Ø 80 mm Entry height/pass-through height: 1500 mm - Straightening rolls hardened, ground and hard-chromed, with central support - Pinch rolls hardened, ground and hard-chromed, with hydraulic lifting - Manual straightening roll adjustment - Feed assist with hydraulically extendable tongue and hydraulically adjustable deflection pulley - Adjustable side strip guides - All straightening rolls driven via distribution gearbox and cardan shafts - Both pinch rolls driven via gearbox with cardan shafts - Frequency-controlled drive via geared motors - Straightener opening stroke 250 mm for cleaning or for processing thicker material, lifting by trapezoidal-thread spindle - Ultrasonic loop control Transport dimensions (L x W x H): 3600 x 2200 x 2200 mm Net weight: approx. 4 tons Decoiler HMS Type BA 1.5-06/80, Machine No. Coil weight: max. 8000 kg Outer coil diameter: max. 1600 mm (with load carriage) Outer coil diameter: max. 2000 mm (without load carriage) Diameter of coil turntable: Ø 1700 mm Coil inner diameter, expansion range: 460–520 mm Coil width, nominal: max. 630 mm Expansion jaw width: 750 mm Height of decoiler drum above base plate: 1500 mm - Decoiler drum driven by hydraulic motor and gear - Pneumatic overrun brake on the decoiler drum (TWINFLEX) - Hydraulic expansion of the decoiler drum, centrally via wedge slider system - Hydraulic pressure arm with hydraulically driven double pendulum roller - Coil loading carriage with 12-ton lifting capacity and 300 mm stroke - Decoiler on elevated travel frame with motorized cross travel drive Transport dimensions (L x W x H): 3500 x 1900 x 2500 mm Net weight: approx. 5 tons Central Hydraulic Power Unit (adjacent) Tank capacity: 350 liters Drive power: 18.5 kW - Drive motor with 2x REXROTH tandem pumps - Oil cooler as air heat exchanger with fan motor Transport dimensions (L x W x H): 1600 x 850 x 1450 mm Net weight: approx. 800 kg Electrical Cabinet (adjacent) - All cable connections via Harting connectors Transport dimensions (L x W x H): 2800 x 500 x 2250 mm Net weight: approx. 800 kg

Condition: ready for operation (used), functionality: fully functional, power: 7.5 kW (10.20 HP), 6 rotor knives Godpfx Ajxfzaaog Nouh 2 stator knives Grinding chamber 500 x 250 mm Power 7.5 kW

Condition: good (used), functionality: fully functional, power: 10 kW (13.60 HP), 6 rotor knives Gjdpexfy Tlofx Ag Njuh 2 stator knives Grinding chamber 500 x 250 mm Power 10 kW

Condition: used, Revolving briquetting press RUF type RBK 55/2500/120 S Hydraulic pellet press or briquetting press for grinding sludge, metal chips, or similar Guodpfxohg Uz Ie Ag Nsh No. 70002 Year of construction 2009 Briquette diameter 120 mm Briquette length in the pre-compactor approx. 120 mm Pressing force in the pre-compactor 30 tons at 260 bar Briquette length in the main compactor approx. 80 mm Pressing force of the main press cylinder 250 tons at 260 bar Stroke size of the main press cylinder 120 mm Pressing force of the counter-press cylinder 250 tons at 260 bar Stroke size of the counterpress cylinder 15 mm Piston diameter of the main press cylinder 350 mm Press stroke Cycle time approx. 30 sec. for grinding sludge with low residual oil content Hopper size of the screw conveyor 1000 x 600 mm Hydraulic motor power 37 kW Mains connection 400 Volt, 50 Hz, 45 kW - Revolver with 5 stations for high material throughput - Pre-compressor stage for pressing material into the turret disk - 2 opposing main press cylinders with 120 mm and 15 mm stroke - Ejection cylinder for ejecting the finished briquettes from the turret disk - Infinitely variable adjustment of the hydraulic speed for each pressing stage - was used for grinding sludge from metal processing - Material hopper as hopper with screw conveyor - the machine was completely overhauled at RUF in 2018 - a new SIEMENS Simatic touch panel was installed in 2020 - only a few operating hours after the overhaul very good condition Grinding sludge recycling - great savings through cooling lubricant recovery - Large savings in disposal costs due to the reduction in volume and weight of the grinding sludge - Grinding sludge briquettes with a low residual oil content can possibly be classified as "non-hazardous waste".

Condition: new, functionality: fully functional, Year of construction: 2025, Direct from production - ready for transport, the GWEIKE Fiber Laser “Pull-out Platform” 3015-P Laser source from IPG fiber lasers: safe and reliable World-renowned brand represented by Danmar Machines BV, ALMELO The GWEIKE laser cutting machine utilizes the powerful YLS-CUT series fiber lasers from IPG. Powerful cutting capacity for stainless steel, aluminium, and other metals, with cutting thicknesses up to 40 mm. Long service life Performance is stable, the lifespan of key components can reach up to 100,000 hours, and the overall equipment quality is guaranteed. Stable cutting performance Godsxmuw Uspfx Ag Nouh The lasers deliver superior beam quality, finer cutting lines, increased productivity, and enhanced processing quality. The fully enclosed workspace with a constant temperature environment is more effective in ensuring stable laser operation.

Condition: excellent (used), functionality: fully functional, Year of construction: 2021, operating hours: 250 h, Since 2021 for customer prints, product demonstrations and trade fair appearances in our possession. Completely ready for use and prepared by manufacturer-certified personnel from IGO3D, Desktop Metal Partner. Gsdpfx Agem Rgzae Njuh Can be demonstrated in Hanover, Germany (also remotely via video call). Easy-to-use Additive Manufacturing 2.0 solutions for industrial production — delivering transformative value. Office-friendly metal 3D printing with two steps (Print > Sinter) and eight materials. Key benefits: „ Easy, two-step processing „ User-friendly software-controlled workflow „ Patented smart Separable SupportsTM technology for quick post-processing „ Qualified for eight materials „ Designed for office-friendly printing „ A trusted system used worldwide with success The easy-to-use Studio System leverages proprietary Bound Metal Deposition™ (BMD), an extrusion-based metal additive manufacturing process where metal rods — metal powder held together by wax and polymer binder — are heated and extruded onto the build plate, shaping a part layer by layer. Once printed, the binder is removed via the debind process, and then sintered, causing the metal particles to densify. The Studio System 2 is even easier to use than ever before with new material formulations allowing printed parts to be placed directly into the furnace without the need for a solvent debind. The result is a streamlined two-step process with a nearly hands-free experience. Eight materials are available, including a range of steels, copper, and nickel and titanium alloys. Simplified metal part production using safe-to-handle bound metal rods The Desktop Metal Studio system creates metal parts for functional prototypes, tooling, jigs and fixtures, and low-volume production applications with expert metallurgy built-in. Easily produce difficult-to-machine parts featuring complex geometries like undercuts and internal channels to optimize metal components in an office setting.

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 723 mm high 700 mm deep 04x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Gujdohq Txhspfx Ag Noh Material color: black 03x steel shelves, new dimension: 300 x 700 mm Type: H29/D 02x swivel castors, new 02x brake/steering rollers, new 01x angle set, new for mounting the worktop 08x safety hook, new Material color: compl. galvanized

Condition: excellent (used), functionality: fully functional, Year of construction: 2022, For sale is a complete metal 3D printing system from Desktop Metal, suitable for additive manufacturing with metal powders using the binder jetting process. The system is ideal for prototyping, small-scale production, and research. Included in the purchase price: 1x Printer (Desktop Metal, 12-liter volume) 1x Sintering furnace 1x Gas valve for the sintering furnace 1x Drying furnace 2x Depowdering stations 1x Powder mixer 2x Industrial vacuum cleaners 6x Powder drums Not included in the purchase price (can be purchased optionally): 1x Additional drying furnace 1x Depowdering station (in-house development) 250 kg metal powder 17-4PH Gujdpfx Agjwgky Ij Noh 100 kg metal powder 316L Additional powder drums Protective equipment for 2 people Other accessories

Year of construction: 2018, condition: ready for operation (used), Control Unit Brand MITSUBISHI Model GOT2000 Gjdpfx Agow Uaigs Nouh Additional Equipment Full optimization of 30 dimensions in two quality grades Cutting programs for different customers Cutting at marks made with fluorescent chalk Trimming of margins (beginning and end of the input material) Cutting in bundles (several pieces at once) Counters for meters, total, shifts, operator, monthly Cutting accuracy ±0.2 mm This METAL TECHNIKA OWD-1600 was manufactured in 2018. It features a GOT3000 Mitsubishi controller and excels in full optimization of 30 dimensions across two quality grades. It supports various cutting programs and can handle input material widths from 12 to 250 mm and heights up to 120 mm. Central oil lubrication ensures smooth operation. Consider the opportunity to buy this METAL TECHNIKA OWD-1600 Optimizing Cross-Cut Saw. Contact us for more information about this machine. Application Types Sawing (Wood)

Condition: excellent (used), Desktop Metal 3D Printer Complete System Here we offer you Desktop Metal 3D printer complete system. Desktop Metal 3D printer studio system Complete system: 3D printer + debinding machine + sintering furnace Desktop Metal The three-part solution includes 3D printer, debinder and furnace Manufacturer Desktop Metal Model Desktop Metal Studio System Operating condition Used (Good) Year of manufacture 2019 Desktop Metal Studio System Includes: 1.1 Desktop Metal Studio 3D Printer Bound Metal Deposition (BMD) Technology. Features: Printed materials metal Technology FDM Use Industry Other features Office X-stroke 30 cm (12 in) Y-stroke 20 cm (8 in) Z-stroke 20 cm (8 in) Description: Unlike laser-based systems that selectively melt metal powders, the printer extrudes bonded metal rods - similar to an FDM printer. This eliminates the safety requirements often associated with metal 3D printing, and it enables new features such as the use of closed-cell fills for lightweight strengths. 1.2 Desktop Metal Studio debinder (delamination machine) fully automatic debinding Cleaning tank: 17.4 L (in process) / 22.5 L (stock) Description: The debinder prepares green parts for sintering by dissolving the primary binder. With a low emission design, it requires no external ventilation and is safe for an office environment. Automatic liquid distillation and recycling means no need to refill between cycles. 1.3 Desktop Metal Studio Sintering Furnace Gusdpok Hz Nqjfx Ag Neh hybrid technology (microwaves & conventional heating elements) Installation space 305x205x205mm Carbon housing Gas supply: 2 x 900 L gas cylinders Heating power: 20 kW Features: Function Sinter Configuration Chamber Heat source gas Other features High temperature, automatic Maximum temperature 1,400 °C (2,552 °F) Description: Fully automated and sized to fit through an office door, the furnace delivers industrial-grade sintering in an office-friendly package. Built-in temperature profiles matched to each design and material provide uniform heating and cooling without the residual stresses associated with laser-based systems. Condition: used / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: excellent (used), Year of construction: 2016, Loma Systems Metal Detector with Rejector Model: IQ³ Model conveyor: MD Conveyor, serial number: G7B3C2RS-35150D Year of construction: 2016 220-240 V, 1 Ph, 50/60 Hz, 3 A Belt width: 300 mm, clearance: 350 mm x 150 mm Total dimensions: 2020 mm x 1080 mm x 1120 mm Gusdpfx Agjv T Ah Es Neh

Condition: good (used), Year of construction: 2020, operating hours: 50 h, functionality: fully functional, Desktop DMA series Dynamic mechanical analyzers DMA25 and DMA50 are "desktop" dynamic mechanical analyzers that offer a high force range and excellent flexibility. From glass transition determination to immersion testing, they are powerful and very cost-effective thermomechanical testing platforms. Applications of the Metravib Desktop series Dynamic mechanical analyzers DMA25 and DMA50 for a wide range of applications - DMA and TMA tests - Determination of glass and secondary transitions - Static and quasi-static tests: Creep, stress relaxation, tensile, compression, etc. - Particularly suitable for the characterization of polymers and composites - Tests on materials immersed in a liquid Gujdpferxfy Uex Ag Nsh - Analysis of material moisture dependence - R&D / quality control / training / laboratory work

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 888 mm high 700 mm deep Gsdpfx Ajhq Twyog Nouh 04x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 03x steel shelves, new dimension: 300 x 700 mm Type: H29/D 01x Angle set, new for fixing the worktop 08x safety hook, new Material color: compl. galvanized

Condition: good (used), Year of construction: 2020, Complete set worked only 2 years New price EUR 500.000   Set with: 3d printer Furnace oven Crosslink Oven Inverter and paxcking table Worked with fillament BASF 17.4 stainless steel   Gujdpfx Agswrcuus Noh Build rate 800 cc/Hr 1600 Dpi Up to 800 Dpi with 10pL print head Up to 400 Dpi with 30 pL print head Layer thickness 30 to 200 Micron X - Travel: 400mm Y - Travel: 250mm Z - Travel: 250mm Plastic printer:Yes Metal printer: Yes Resolution: 200 Accurate: 800 Length: 2500mm Width: 1800mm Height: 2310mm Weight: 2000kg

Condition: new, functionality: fully functional, Year of construction: 2025, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, High-strength welding bed Partitioned smoke extraction system Fully automatic butter injection system Fully automatic cutting, material saving, fast speed Cutting area 4000 × 2000 mm X‑axis travel 1520 mm Y‑axis travel 4020 mm Z‑axis travel 80 mm Max. combined positioning speed 170 m/min Acceleration 2.8 G Godpfx Aow A Iilog Neuh Machine dimensions (L×W×H) 9500 × 2900 × 2380 mm Footprint 10500 × 3400 mm Net weight 8500 kg

Condition: used, Pneumatic cylinder, air cylinder, pneumatic stamp, compact cylinder Godpfx Agjm Hd Rzo Njuh -Manufacturer: Metal Work, compact cylinder tray sealing machine Inauen VC999/ TS 1200 N -Type: 121AA20160ZP -Stroke: 160mm -Piston: Ø 120 mm -Piston rod: Ø 32 mm / M27 x 2 -Dimensions: 445/135/H135 mm -Weight: 9.6kg

Condition: excellent (used), Year of construction: 2020, Elektron Metal Detector Aperture 180mm Wide x 405mm High Belt length 1500mm Long Stainless Steel Gujdsvw D Iuspfx Ag Njh Two run features options - alarm and stop or air reject blast Reject bin In excellent condition

Condition: good (used), Year of construction: 2020, operating hours: 20 h, functionality: fully functional, The advantages of DMA+300, DMA+1000 and DMA+2000 DMA and TMA testing Guedpfx Agjrxf Rto Neh Precise measurement of viscoelastic properties Determination of glass and secondary transitions Static and quasi-static tests: Creep, stress relaxation, tension, compression... Fatigue testing of material and industrial component samples (with controlled waveform) Crack growth testing Analysis of solid, pasty and liquid materials: elastomers, plastics, composites, biomaterials, etc. Particularly suitable for the characterization of polymers and composites (polymerized materials, polymerization process tracking, simultaneous DMA/calorimetry, fatigue) Particularly suitable for testing and characterizing elastomers (Mullins effect, Payne effect, frequency sweep, heat build-up, crack growth testing, etc.) Analysis of material moisture dependency Comparison and classification of complex materials for construction R&D / quality control / training / laboratory work DMA+ series with high power Solutions for material characterization The devices in the DMA+ series are dynamic testing machines based on an innovative concept of a one-piece test frame with high rigidity. They are dedicated to accurately analyzing the viscoelastic properties of the most advanced materials. The DMA+ one-piece high stiffness test frame has been designed to offer the widest stiffness and frequency analysis ranges as well as best-in-class ergonomics. The Dyna+ software enables a variety of DMA tests to track the dependence of the material's viscoelastic properties on many parameters. With the optional fatigue module of the Dyna+ software, the testing capabilities can be extended to advanced fatigue tests, heat build-up tests or crack growth tests.

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Guedpfx Ajhq Txweg Neh Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 723 mm high 700 mm deep 02x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 02x swivel castors, new 02x brake / swivel castors, new 01x angle set, new for mounting the worktop 04x safety hook, new Material color: compl. galvanized

Condition: new, functionality: fully functional, Year of construction: 2025, laser type: fiber laser, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, Laser power: 3KW, 6KW, 12KW Standard hardware: waste car, fully automatic butter injection, dual-control workbench, adaptive multi-angle site placement, beam light curtain Optional hardware: fire bricks, high-pressure proportional valve (standard for 6KW and above), safety door lock, Independent laser cabinet, rear exchange table light curtain, rear lifting light barrier, Rear camera, internal camera, monitoring display, radiation-proof glass, upper cover fan, upper cover, partition dust removal Guedpswz Ukyefx Ag Noh

Condition: excellent (used), Year of construction: 2012, Lock met 30+ Throat / Vertical Fall Metal Detector The MET 30+ UNIVERSAL compact vertical fall system can be installed at the beginning of the production line to inspect materials in bulk powder or granule form or anywhere for free falling products. • Detects real-life contaminants • ATEX zone 21 approved • Throughput up to 50 tonnes per hour • Quick release sealed valve or cowbell reject mechanisms available • Sealed to IP 66 for washdown applications Gsdpfou Dntlox Ag Neuh

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 888 mm high 700 mm deep 02x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 01x angle set, new for fixing the worktop 04x safety hook, new Gsdpshq Tqdofx Ag Njuh Material color: compl. galvanized

Condition: new, Year of construction: 2025, functionality: fully functional, coil outer diameter: 1,500 mm, coil inner diameter: 508 mm, product height (max.): 200 mm, feed length X-axis: 1,520 mm, feed length Y-axis: 3,020 mm, feed length Z-axis: 80 mm, warranty duration: 24 months, total height: 2,380 mm, total length: 8,900 mm, total width: 2,300 mm, load capacity: 1,300 kg, input frequency: 50 Hz, input voltage: 380 V, overall weight: 180 kg, repeat accuracy: 0.02 mm, workpiece weight (max.): 15,000 kg, Equipment: cooling unit, GS-J Series has various workbench sizes such as 3015, 4015, 4020, 6015 to meet different processing needs Suitable for batch processing of thin plates with high flatness requirements of 0.6-3.0mm Uncoiling machine parameters: Maximum weight of coil (kg): 15000 Coil width (mm): 200～1524 Coil outer diameter (mm): Φ800～Φ1500 Coil inner diameter (mm): Φ508mm~Φ610mm (cast iron pad) Coil thickness: (mm) 0.6-2.0mm (stainless steel) ≤1524mm 0.8-3.0mm (carbon steel) ≤1524mm Feeding length (mm): 0～ Maximum stroke of equipment Unwinding speed (m/min): 0～15 Moving speed (mm/s): 0-8 Lifting speed (mm/s): 3.0 Lifting stroke (mm) : 350 Leveling flatness (mm/㎡): ≤±3 Fixed feeding line height (mm) : 870 Sizing accuracy (mm/m) : Length direction ≤±0.2 Diagonal direction : ≤±0.8 Revolutionize Your Coil Processing with One Machine, Five Functions! Uncoiling, leveling, feeding, cutting, and blanking – all in one seamless automated system for maximum efficiency. Smart, Flexible & Versatile - Effortlessly cuts special-shaped workpieces, adapting to diverse production needs - Optional touchscreen control with top-tier international cutting systems Gusdpfx Agev Awgus Njh - High-quality drag chain cables – durable, bend-resistant, and interference-free

Condition: good (used), Technical data for pallet rack beam: Racking system: Metall Sistem Type: Unipal Scope of delivery includes: 01x pallet rack beam, used Material color: yellow Box profile: 140 x 45 mm Clear width: 1,800 mm Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is offered for collection only. Any additional transport or shipment of this item will incur extra costs, which can be quoted separately depending on the place of delivery or scope of delivery. Gedpfxexb Tp Ej Ag Nsuh