Used Pallet Racking Heavy Duty Shelving for sale (13,690)

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Ibjdpfx Ageh U Rzgs Nec Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Year of construction: 2025, condition: new, functionality: fully functional, rotor diameter: 520 mm, rotor width: 800 mm, Genox GXC800 Series - Heavy Duty Granulator suitable for processing various materials including plastics, wood, rubber etc. 55kW Drive Motor with outboard rotor bearings (75kW & 90kW drive options are available), heavy duty precision machined rotor, and 520rpm operating speed as standard. 800mm wide x 520mm diameter cutting chamber with a choice of either a 10 knife, 5 row V Cutting Rotor, or our heavy duty, high inertia Cascade Rotor with 40 x rotor knives. Two rows of counter knives are mounted in the chamber and as an option a third row can be mounted in the throat of the machine to increase cutting efficiency. All knives are manufactured from Vacuum Heat Treated D2 Tool Steel. Hydraulic assisted chamber and screen access with integrated safety interlocks, and a setting jig is supplied for pre-setting of knives off the machine to enable quick, simplified knife changes. Output size is controlled by replaceable screens mounted beneath the rotor shaft - sizes supplied as required (4mm-50mm). A sound attenuation enclosure is available as an option to minimise operational noise if required. Ibodpfoxnaqvsx Ag Noc We can provide infeed conveyors and product conveying systems as required to transfer product in to bulk storage bags if required.

Condition: ready for operation (used), throat depth: 1,100 mm, Heavy duty double column bandsaw sawing cap: dia 1100 mm autofeed with stroke of 500 mm (with unlimited repositioning) enlarged height of sawblade: 67 mm chipconveyor equipped with fully motorized Weisshaupt rollerconveyors: Ibjdpfx Agexpggae Nsc - 6 meter in-feed rollerconveyor (outside) with 1 manual clamp for aligning workpiece - 3 meter in-feed rollerconveyor (inside) with 2 manual clamps for aligning workpiece - max workpiece width: 1100 mm - each roll is motorized - cap of one roll is 4 ton - 2 meter out-feed rollerconveyor - one rollerconveyor is equipped with scales to weigh workpiece after cutting (Sartorius system) Max height of workpiece: 1100 mm Length of band saw: 11400 x 67 x 1,6 mm

Year of construction: 2000, condition: ready for operation (used), functionality: fully functional, AVAILABLE ONLY DUE TO FACTORY CLOSURE An excellent condition very powerful 75Kw granulator, with a special blade configuration ( HOG) to manage large lump materials without in most cases, need for cutting or a shredder. Maintained by Owner / engineer to high standard and was considered one of the best granulators in his factory. This offer comes with a large bandsaw to pre-cut any oversize, rare earth magnet on the output, followed by a fines separator, electronic s+s metal detection and removal equipment. Kongskilde fan, cyclones and pipework complete the running system. Spare screens and spare Blades enable immediate start up for buyer. Electric mains isolators and control panel included so only needs one conenction into the board to commence operation. Truly a "plug and play" granulation line. Price includes loading to buyers transport. delivery can be arranged at cost. Iodowqxwcspfx Ag Njbc

Condition: used, Year of construction: 1988, turning diameter over bed 2000 mm turning diameter over slide rest / mm turning length / mm - Type 1 K 671 320 F3 - Year of manufacture 1988 (first commissioned in 1998) - Turning length 10,000 mm - Turning diameter over bed 2,000 mm (modified) - Faceplate diameter 1,950 mm - Faceplate clamping range 400 - 1,350 mm - Speeds 1.00 - 140 rpm - Torque 125,000 Nm - Main cutting force 130 kN max. - Automatic swiveling tailstock - Max. workpiece weight 70 tonnes - Max. workpiece weight with steady rest 100 tonnes - Drive power 100 kW - Number of bed ways 4 - Dimensions 22,000 x 6,200 x 2,900 mm - CNC control SIEMENS 840D (2010 for €220,000.00) - Support feed X-Z 0.3 - 4,000 mm/min. Ibodpfjxn Tz Iex Ag Nsc - Support rapid traverse X-Z 4,000 mm/min. - Inner cone dimensions 140 x 1:7 - The machine complies with CE guidelines - Includes 2 steady rests, 1 roller block, 4 jaws, boring device - Condition: very good condition

Condition: good (used), 19 heavy-duty conveyor rollers 238 mm Ø x 600 mm roller shell length with 40 mm Ø shaft and 2 pedestal bearings, with chain wheel 16 B1/Z= 17, 1 geared motor drive with fluid coupling, if required also 6 spiral rollers for right-hand discharge 238/266 mm Ø x 900 mm Ibedpfx Aewb A Hveg Nsc

Condition: like new (used), Stow pallet racking system. Frame height: 11 meters. Beam length: 3.60 meters. Number of frames: 144. Number of beams: 1,944. Racking depth: 1.10 meters. Various impact protections included, locking pins / safety pins for the beams, complete set. The racking is currently still assembled but can be delivered dismantled, or you can dismantle it yourself by arrangement. The racking is AS NEW – no scratches, dents, or damages. For more information, please call or email! Iodpfx Agsxn A A Is Nsbc

Year of construction: 2025, condition: new, functionality: fully functional, rotor diameter: 660 mm, rotor width: 1,600 mm, Genox GXC1600T Series - Heavy Duty Granulator suitable for processing various materials including plastics, wood, rubber etc. 110kW Drive Motor with outboard rotor bearings (132kW & 160kW drive options are available), heavy duty precision machined rotor, and 480rpm operating speed as standard. 1,600mm wide x 660mm diameter cutting chamber with a choice of either a 5 row or 7 row V Cutting Rotor. Two rows of counter knives are mounted in the chamber and as an option a third row can be mounted in the throat of the machine to increase cutting efficiency. All knives are manufactured from Vacuum Heat Treated D2 Tool Steel. Hydraulic assisted chamber and screen access with integrated safety interlocks, and a setting jig is supplied for pre-setting of knives off the machine to enable quick, simplified knife changes. Output size is controlled by replaceable screens mounted beneath the rotor shaft - sizes supplied as required (4mm-50mm). A sound attenuation enclosure is available as an option to minimise operational noise if required. We can provide infeed conveyors and product conveying systems as required to transfer product in to bulk storage bags if required. Iodpoxnaqiofx Ag Nebc

Condition: ready for operation (used), total height: 3,340 mm, total length: 4,500 mm, total width: 1,950 mm, throat depth: 660 mm, Type: ONL 660x700 ACN Heavy duty double column bandsaw specific for high-alloy steels CNC touch control with saw parameters for various types of high-alloy steels cap round: dia 660 mm cap square: 660 x 700 mm bundle cap: 555 x 700 mm autofeed with stroke of 500 mm (with unlimited repositioning) sawing power: 18,5 kW the in-feed and sawing speeds are frecquency controlled enlarged height of sawblade: 67 mm chipconveyor equipped with fully motorized Weisshaupt rollerconveyors: - 10,3 meter in-feed rollerconveyor (outside) with 2 hydraulic clamps for aligning workpiece Iedpfx Agoxpgggs Njbc - 9 meter in-feed rollerconveyor (inside) with 2 hydraulic clamps for aligning workpiece - max workpiece width: 900 mm - each roll is motorized - cap of one roll is 4 ton - 4 meter out-feed rollerconveyor: one rollerconveyor is equipped with scales to weigh workpiece after cutting (Sartorius system) Max height of workpiece: 700 mm Sawspeed: 10 > 120 m/min Length of band saw: 8660 x 67 x 1,6 mm Power needed: 27 kW (58 amp) Weight: 8,5 ton (only machine)

Year of construction: 2003, condition: refurbished (used), functionality: fully functional, machine/vehicle number: BF 030003, This heavy duty 1200mm Granulator was refurbished fully in 2020 . Since then it has done only a very few tonnes of light weight containers after the refurbishment. New fixed and fly blades were fitted recently and it has not run since. 4 Rotating blades and 2 Stator blades. The semi solid rotor is water cooled if needed. Single step Belt drive from 110Kw Motor. Up to 1500 kgs per hour depending on the type of materials and feed rate. Air extractio to cyclone and bagging tower for big bags (FIBC) included. Loading conveyor with metal detection tunnel also included. Capable of grinding rubber also as fitted with the water cooled rotor. Two hoppers included , a standard one as shown in pictures and also included is a top entry completely enclosed hopper (not shown) suitable to received pre-shredded plastics or rubber. Ijdpfx Agov Su A Ej Nebc

Condition: good (used), Platform trolley, transport trolley, heavy-duty trolley, table trolley, assembly trolley, industrial trailer, container dolly, double turntable steering, heavy-duty trailer -Heavy-duty transport vehicle: Industrial trailer with 2-axle turntable steering -Platform: 4490/1450/H660 mm, dimensions see photo technical drawing -Load capacity: 13.5 t Iedpfjl Sr A Tjx Ag Nebc -Tires: solid rubber -Transport dimensions: 5960/1700/H1450 mm -Weight: 1340 kg

Condition: good (used), Technical Data for the Pallet Racking System: Racking System: Arestant Type: AS Setup Details: Number of rack rows: 01 unit Length per rack row: 19,575 mm Number of bays per rack row: 07 units Number of levels incl. ground level: 02 units Volume Data: Pallet locations per bay: 09 units Pallet locations per rack row: 63 units Total pallet locations: 63 units Based on: Load carrier: Euro pallet EN 13698-1 Dimensions: 1,200 x 800 x 150 mm Total height incl. pallet: n/a Weight per pallet (max.): n/a Scope of delivery includes: 08x pallet rack uprights, used Colour: blue Frame type: 878 Profile dimensions: 80 x 77 x 1.8 mm Incl. horizontal and diagonal bracing, base plates Uprights are pre-assembled (bolted lattice structure) 4,000 mm high 1,100 mm deep 28x pallet rack beams, used Colour: orange Box profile: 120 x 50 mm Connector: 4 HK (hooks) Clear width: 2,705 mm 56x safety pins, used Finish: sendzimir galvanized Ibsdpfsw Ud U Hex Ag Noc For securing beams against unintentional lifting 32x anchor bolts, new Manufacturer: Hilti Model: HST2 M12x105/10 Material: carbon steel, galvanized Approved for: cracked concrete 16x leveling plates, used Finish: fully galvanized For leveling uprights on uneven floors 01x load sign With specifications for bay and shelf loads, manufacturer and commission number Dimensions: 420 x 297 x 3 mm Your contact persons in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General Information about the Item: This item is offered for collection only. If you require shipping or transport, additional costs will apply. These can be requested separately depending on destination and scope of delivery.

Condition: excellent (used), mileage: 70,972 km, gearing type: automatic, fuel type: diesel, fuel tank capacity: 400 l, color: beige, axle configuration: 10x4, first registration: 10/2017, emission class: euro6, brakes: engine braking, Year of construction: 2017, Equipment: ABS, air conditioning, cruise control, soot filter, = Additional Options and Equipment = - Aluminum fuel tank - Leaf suspension - Power brake booster - Electric windows - Electrically adjustable exterior mirrors - High beam - Low noise - Speed limiter - LED lights - Air suspension - Air horn - Navigation system - Fog lights - Particulate filter - Sun visor - Spoiler - Stability control - Power take-off (PTO) - Central lubrication system - Central locking = Further Information = General Information Cab: Day cab Technical Information Number of cylinders: 6 Engine displacement: 12,777 cc Drivetrain AdBlue system: Yes Transmission Transmission: I-SHIFT, automatic Axle Configuration Front axle 1: Steered Front axle 2: Steered Rear axle 1: Twin tires Rear axle 2: Twin tires Rear axle 3: Twin tires; lift axle; steered Dimensions and Weights Ibodpjuxwcfjfx Ag Nsc Unladen weight: 22,680 kg Wheelbase: 430 cm Functional Body manufacturer: KH-KIPPER W1MV Tipping body: Rear tipper Condition Technical condition: Very good Optical condition: Very good Financial Information Price: On request VOLVO FMX 540 10X4 HEAVY DUTY TIPPER TRUCK EURO 6 L PACKAGE 540 HP 10X4 DRIVE, LAST AXLE LIFT AND STEERABLE AXLE WHEELBASE 430 CM HUB REDUCTION AXLE LEAF SPRING SUSPENSION I-SHIFT AUTOMATED TRANSMISSION WITH CREEPER GEAR VEB+ FMX CAB WITH AIR CONDITIONING, HEATING, CAMERA, NAVIGATION EU REGISTRATION KH-KIPPER TYPE: M1MV LOAD CAPACITY: 27 M3 HYDRAULIC TAILGATE TIPPER BODY MADE OF HARDOX STEEL OIL COOLER FOR HYDRAULICS CENTRAL LUBRICATION SYSTEM TECHNICAL GROSS WEIGHT: 68,000 KG CE CERTIFICATION FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPAÑOL WE SPEAK ENGLISH

Year of construction: 2025, condition: new, functionality: fully functional, rotor diameter: 660 mm, rotor width: 1,200 mm, Genox GXC1200T Series - Heavy Duty Granulator suitable for processing various materials including plastics, wood, rubber etc. 90kW Drive Motor with outboard rotor bearings (110kW & 132kW drive options are available), heavy duty precision machined rotor, and 480rpm operating speed as standard. 1,200mm wide x 660mm diameter cutting chamber with a choice of either a 10 knife/5 row or 14 knife/7 row V Cutting Rotor, or our heavy duty, high inertia Cascade Rotor with 60 x rotor knives. Two rows of counter knives are mounted in the chamber and as an option a third row can be mounted in the throat of the machine to increase cutting efficiency. All knives are manufactured from Vacuum Heat Treated D2 Tool Steel. Hydraulic assisted chamber and screen access with integrated safety interlocks, and a setting jig is supplied for pre-setting of knives off the machine to enable quick, simplified knife changes. Output size is controlled by replaceable screens mounted beneath the rotor shaft - sizes supplied as required (4mm-50mm). A sound attenuation enclosure is available as an option to minimise operational noise if required. We can provide infeed conveyors and product conveying systems as required to transfer product in to bulk storage bags if required. Iodpfexnaqcex Ag Njbc

Condition: used, Diesel - forklift truck, compact forklift MORA type M80CS make no. 20087 year of construction 2006 Rated capacity 8 ton. Lifting height 3800 mm fork length 1800 mm fork carriage width 1460 mm overall height 3030 mm Total width 1460 mm Total length without forks 3350 mm Ibedpfx Aoitv Rdeg Nsc Dead weight 12740 kg - Duplex mast with 1950 mm free stroke - 4 cylinder PERKINS diesel engine - completely closed cab with heating - electro-hydraulic tipping device for the driver's cab - hydraulic auxiliary steering - 2 pieces working lights in front, 1 piece working light in the rear - yellow warning-flashing light on the protective roof - solid rubber tires (front 28 x 10 x 22) (rear 250/70 - 16) - 9646 operating hours read off - UVV-TÜV acceptance new good condition Renting on request

Condition: used, Technical specifications for the pallet racking system: Racking system: Bito Type: PL38 Technical specifications for installation: Number of racking rows: 01 pcs Length per racking row: approx. 2,380 mm Number of bays per racking row: 01 pcs, each 2,200 mm Number of levels incl. ground level: 03 pcs Scope of delivery includes: 02x Pallet rack uprights, used Material finish: Sendzimir galvanized Frame type: P20 Profile dimensions: 90 x 65 x 2.0 mm Including cross and diagonal bracing, base plates Uprights supplied pre-assembled (bolted lattice frame) 2,480 mm high 600 mm deep 06x Pallet rack beams, used Material finish: black Box section: 104|80 x 50 mm Beam type: PST22.104 Connector: 3 HK (hooks) Clear span: approx. 2,200 mm 12x Locking pins, used Material finish: Sendzimir galvanized For securing the longitudinal beams against accidental lifting 08x Through bolts, new Manufacturer: Hilti Type designation: HST2 M12x105/10 Version: carbon steel, galvanized Approved for: cracked concrete 04x Shims, used Version: fully galvanized For leveling the rack uprights when installed on uneven floors 15x Steel panels, used Total depth: approx. 585 mm Ijdpfx Aew Edxzjg Nebc Total width: approx. 455 mm Material finish: Sendzimir galvanized 01x Load sign With information on bay and shelf loads, manufacturer, and order number Dimensions: 420 x 297 x 3 mm Your contacts at our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is offered for collection only. Should transport or shipping of this item be required, additional costs will be incurred, which can be provided on request depending on delivery location and order volume.

Condition: excellent (used), mileage: 279,179 km, first registration: 02/2009, fuel type: diesel, color: white, axle configuration: 8x6, fuel: diesel, wheelbase: 4,200 mm, brakes: retarder, driver cabin: sleeper cab, gearing type: mechanical, emission class: euro5, Year of construction: 2009, Equipment: ABS, air conditioning, cruise control, soot filter, spoiler, trailer coupling, = Additional Options and Accessories = - Aluminum fuel tank - Leaf spring suspension - Roof spoiler - Electric windows - Electrically adjustable exterior mirrors - Low-noise operation - Speed limiter - Air horn - Fog lights - Particulate filter - Sleeper cab - Sun visor - Stability control - Toolbox - Power take-off (PTO) - Central locking - Towing hitch = Further Information = Iedpouxutnjfx Ag Nebc Technical Information Number of cylinders: 8 Engine displacement: 15,928 cc Unladen weight: 15,000 kg Drivetrain Fuel tank: 1,000 liters Axle Configuration Front axle: Steered Rear axle 1: Steered Rear axle 2: Twin tires Rear axle 3: Twin tires Condition Technical condition: very good Visual condition: very good Financial Information Price: On request MERCEDES-BENZ ACTROS 4360 V8 SLT 8X6 TITAN HEAVY DUTY TRACTOR UNIT PUSH AND PULL POWER 250 TON EURO 5 L PACKAGE (CAN BE CONVERTED TO EURO 3 FOR EXPORT) V8 ENGINE 600 HP 8X6 DRIVE WHEELBASE 420 CM DIFF LOCKS FIFTH WHEEL + TRAILER COUPLING HYDRAULICS FOR LOWBED TRAILER LARGE 1,000 LITER FUEL TANK BEHIND THE CAB TRANSMISSION WSK 440 RETARDER PUSH AND PULL CAPACITY 250 TONNES !!!! FRONT PUSH BUMPER EXTRA COOLING PACKAGE OIL AND AIR VALVES FRONT AND REAR TOOLBOXES CAB WITH ALL OPTIONS FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPAÑOL WE SPEAK ENGLISH

Condition: new, Year of construction: 2025, functionality: fully functional, overall weight: 15,500 kg, rotor diameter: 800 mm, rotor width: 2,000 mm, power: 250 kW (339.91 HP), rotational speed (max.): 480 rpm, Equipment: rotational speed infinitely variable, Genox GXC2000G Series - Heavy Duty Granulator suitable for processing various materials including plastics, wood, rubber etc. 250kW Drive Motor with outboard rotor bearings (200kW - 315kW drive options are available), heavy duty precision machined rotor, and 480rpm operating speed as standard. 2,000mm wide x 800mm diameter cutting chamber with a choice of either a 5, 7 or 9 row V Cutting Rotor. Two rows of counter knives are mounted in the chamber and as an option a third row can be mounted in the throat of the machine to increase cutting efficiency. All knives are manufactured from Vacuum Heat Treated D2 Tool Steel. Hydraulic assisted chamber and screen access with integrated safety interlocks, and a setting jig is supplied for pre-setting of knives off the machine to enable quick, simplified knife changes. Output size is controlled by replaceable screens mounted beneath the rotor shaft - sizes supplied as required (4mm-50mm). A sound attenuation enclosure is available as an option to minimise operational noise if required. We can provide infeed conveyors and product conveying systems as required to transfer product in to bulk storage bags if required. Ibsdpfxoxnap Ss Ag Nsc

Condition: good (used), Technical Data for the Pallet Racking System: Racking System: META Rack Technical Details for Installation: Number of rack rows: 01 unit Length per rack row: 13,890 mm Number of bays per row: 06 units Scope of Delivery: - 07x Pallet rack uprights, used Material finish: Sendzimir galvanized Profile dimensions: P 90 x 65 x 1.50 mm Upright type: PN-15 Including transverse and diagonal braces, footplates Uprights are pre-assembled (bolted truss design) Height: 4,500 mm Depth: 1,100 mm - 36x Pallet racking beams, used Material finish: Orange Box profile: 95 x 50 mm Beam type: 95|55 Connector: 4-hook Clear span: 2,210 mm Max. load per pair of beams: 2,400 kg (with evenly distributed load) - 07x Upright protectors, used Material finish: hot-dip galvanized Overall height: approx. 970 mm Total width: approx. 98 mm Internal width: approx. 92 mm Total depth: approx. 40 mm Material thickness: approx. 3.00 mm Bore diameter: approx. 11 mm Number of bores: 04 units - 72x Safety pins, used Material finish: Sendzimir galvanized For securing the beams against accidental lifting - 28x Anchor bolts, new Manufacturer: Hilti Model: HST2 M12x105/10 Material: carbon steel, galvanized Approved for cracked concrete - 14x Shims, used Finish: fully galvanized For leveling uprights on uneven floors - 01x Load capacity sign With specifications for bay and shelf loads, manufacturer, and order number Dimensions: 420 x 297 x 3 mm Your contact persons at our company: Mr. Andre Evering Ijdpfow T Sipjx Ag Nsbc Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is offered for collection only. Any requested transport or shipping of this item will incur additional costs, which can be requested separately from us depending on the place of delivery and scope of delivery.

Condition: excellent (used), mileage: 577,458 km, first registration: 01/2013, fuel type: diesel, color: yellow, axle configuration: 8x4, fuel: diesel, wheelbase: 3,900 mm, brakes: retarder, driver cabin: sleeper cab, gearing type: automatic, emission class: euro5, Year of construction: 2013, Equipment: ABS, air conditioning, cruise control, soot filter, spoiler, trailer coupling, = Additional Options and Accessories = Ibjdpfouxrwdex Ag Noc - Aluminium fuel tank - Leaf suspension - Roof spoiler - Electric windows - Electrically adjustable exterior mirrors - Low noise emissions - Speed limiter - Refrigerator - Air horn - Fog lights - Particulate filter - Reversing camera - Sleeper cab - Sun visor - Stability control - Toolbox - Power take-off (PTO) - Towing jaw = Additional Information = Technical Information Number of cylinders: 8 Engine displacement: 15,928 cc Axle Configuration Front axle: Steering Rear axle 1: Steering Rear axle 2: Twin tyres Rear axle 3: Twin tyres Dimensions and Weights Unladen weight: 13,689 kg Dimensions (L x W): 763 x 250 cm Condition Technical condition: very good Visual condition: very good Financial Information Price: On request Identification Registration: 27-BBL-9 MERCEDES-BENZ 4165 V8 8X4 SLT TITAN HEAVY-DUTY TRACTOR UNIT EURO 5 L PACKAGE (CAN BE ADAPTED TO EURO 3 FOR EXPORT) V8 ENGINE 650 HP 8X4 DRIVE LEAF SPRING SUSPENSION WHEELBASE 390 CM DIFFERENTIAL LOCKS ADJUSTABLE 3.5 INCH FIFTH WHEEL + TRAILER COUPLING HYDRAULICS FOR TRAILER LARGE 900 LITRE TANK BEHIND CAB AUTOMATIC GEARBOX WITH VIAB TURBO RETARDER CLUTCH (TORQUE CONVERTER TURBO CLUTCH) RETARDER PUSH AND PULL 250,000 KG FRONT PLATE FOR HEAVY-DUTY COUPLING EXTRA COOLING PACKAGE FOR VIAB TURBO RETARDER CLUTCH EXTRA OIL AND AIR CONNECTIONS FRONT AND REAR MULTIPLE TOOLBOXES CAB FULLY EQUIPPED: AIR CONDITIONING, FRIDGE, CAMERA FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPAÑOL WE SPEAK ENGLISH

Year of construction: 2025, condition: new, functionality: fully functional, rotor diameter: 520 mm, rotor width: 1,200 mm, Genox GXC1200 Series - Heavy Duty Granulator suitable for processing various materials including plastics, wood, rubber etc. 75kW Drive Motor with outboard rotor bearings (90kW & 110kW drive options are available), heavy duty precision machined rotor, and 520rpm operating speed as standard. 1,200mm wide x 520mm diameter cutting chamber with a choice of either a 10 knife, 5 row V Cutting Rotor, or our heavy duty, high inertia Cascade Rotor with 60 x rotor knives. Two rows of counter knives are mounted in the chamber and as an option a third row can be mounted in the throat of the machine to increase cutting efficiency. Iedpsxnapxjfx Ag Nebc All knives are manufactured from Vacuum Heat Treated D2 Tool Steel. Hydraulic assisted chamber and screen access with integrated safety interlocks, and a setting jig is supplied for pre-setting of knives off the machine to enable quick, simplified knife changes. Output size is controlled by replaceable screens mounted beneath the rotor shaft - sizes supplied as required (4mm-50mm). A sound attenuation enclosure is available as an option to minimise operational noise if required. We can provide infeed conveyors and product conveying systems as required to transfer product in to bulk storage bags if required.

Condition: excellent (used), mileage: 332,987 km, power: 478 kW (649.90 HP), first registration: 08/2010, fuel type: diesel, color: yellow, axle configuration: 8x4, fuel: diesel, brakes: retarder, driver cabin: sleeper cab, gearing type: automatic, emission class: euro5, Year of construction: 2010, Equipment: ABS, air conditioning, cruise control, parking heater, soot filter, spoiler, trailer coupling, = Additional Options and Equipment = - Aluminum fuel tank - Leaf suspension Ibedpfxouxqw As Ag Nsc - Roof spoiler - Electric windows - Electrically adjustable exterior mirrors - Low noise emission - Speed limiter - Refrigerator - Air horn - Fog lights - Particulate filter - Sleeper cab - Sun visor - Stability control - Auxiliary heater - Toolbox - Power take-off (PTO) - Towing jaw = Additional Information = Transmission: TORQ CONVERTOR TURBO CLUTCH, automatic Front axle 1: Steered Front axle 2: Steered Rear axle 1: Twin tires Rear axle 2: Twin tires Fuel tank: 1000 liters Technical condition: very good Visual condition: very good Price: On request MERCEDES-BENZ ACTROS 4165 V8 8X4 HEAVY DUTY HEAVY HAULAGE TRACTOR UNIT EURO 5 L PACKAGE (CAN ALSO BE ADJUSTED TO EURO 3 FOR EXPORT) V8 ENGINE 650 HP DRIVE 8X4 LEAF SUSPENSION WHEELBASE 390 CM DIFFERENTIAL LOCKS ADJUSTABLE FIFTH WHEEL 3.5 INCH + TRAILER COUPLING HYDRAULICS FOR TRAILER LARGE 900 LITER TANK BEHIND THE CAB AUTOMATIC GEARBOX WITH VIAB TURBO RETARDER CLUTCH (TORQ CONVERTOR TURBO CLUTCH) RETARDER PULLING CAPACITY 250,000 KG EXTRA COOLING PACKAGE FOR VIAB TURBO RETARDER CLUTCH EXTRA OIL AND AIR CONNECTIONS FRONT AND REAR TOOLBOX FULLY EQUIPPED CAB FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPAÑOL WE SPEAK ENGLISH

Condition: excellent (used), mileage: 69,000 km, power: 412 kW (560.16 HP), first registration: 10/2011, fuel type: diesel, color: red, axle configuration: 6x6, fuel: diesel, wheelbase: 3,800 mm, brakes: retarder, driver cabin: sleeper cab, gearing type: mechanical, emission class: euro5, Year of construction: 2011, Equipment: ABS, air conditioning, all wheel drive, cruise control, parking heater, soot filter, spoiler, = Additional options and equipment = - Aluminum fuel tank - Leaf suspension - Brake booster - Roof spoiler - Electric windows - Electrically adjustable exterior mirrors - Speed limiter - Fog lights - Particulate filter - Sleeper cab - Stability control Iedpfx Aeuxqf Tog Njbc - Auxiliary heater - Toolbox - PTO (Power Take-Off) = Further information = Transmission: WSK, manual gearbox Front axle: Steered Rear axle 1: Twin tires Rear axle 2: Twin tires Fuel tank: 800 liters Technical condition: very good Visual condition: very good Price: On request IVECO SIVI TRAKKER 560 6X6 HEAVY DUTY TRACTOR UNIT 275 TONS!!! EURO 6 L PACKAGE 580 HP DRIVE 6X6 LEAF SPRUNG MANUAL GEARBOX WITH WSK TORQ 440 WHEELBASE 380 CM DIFFERENTIAL LOCKS HYDRAULICS FOR TRAILERS LARGE COOLING PACKAGE BEHIND THE CAB HYDRAULICS FOR LOW-LOADER FRONT AND REAR EXTRA OIL AND AIR VALVES TWISTLOCKS FOR BALLAST FLATBED SPARE WHEEL RETARDER SLEEPER CAB WITH AIR CONDITIONING-WEBASTO PUSH AND PULLING CAPACITY 275 TONS FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPAÑOL WE SPEAK ENGLISH

Condition: excellent (used), mileage: 401,000 km, power: 500 kW (679.81 HP), first registration: 06/2009, fuel type: diesel, color: other, axle configuration: 8x4, fuel: diesel, wheelbase: 4,050 mm, brakes: retarder, driver cabin: sleeper cab, gearing type: automatic, emission class: euro5, Year of construction: 2009, Equipment: ABS, air conditioning, cruise control, parking heater, spoiler, = Additional Options and Equipment = - Aluminium fuel tank - Roof spoiler - Electric windows - Electrically adjustable exterior mirrors - High beam - Low noise - Speed limiter - Intarder - Refrigerator - Air horn - Fog lights - Sleeper cab - Sun visor - Auxiliary heater - Stationary air conditioning Ijdpfxouu Dfde Ag Nobc - Toolbox - PTO (power take-off) - Central locking = Further Information = Transmission: WSK TORQ CONVERTOR, automatic Technical condition: very good Optical condition: very good Price: On request

Condition: excellent (used), mileage: 371,993 km, power: 471 kW (640.38 HP), first registration: 04/2017, fuel type: diesel, color: green, axle configuration: 8x4, tire size: 385/65/22.5, fuel: diesel, wheelbase: 4,100 mm, brakes: retarder, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, suspension: steel, Year of construction: 2017, Equipment: ABS, air conditioning, cruise control, differential lock, navigation system, parking heater, soot filter, trailer coupling, = Additional Options and Accessories = - Aluminum fuel tank - Leaf spring suspension - Power brake booster - Electric windows - Electrically adjustable exterior mirrors - High beams - Speed limiter - Hydraulic tilt system - Refrigerator - Alloy wheels - Fog lights - Particulate filter - Reversing camera - Sleeping cabin - Auxiliary heating - Power take-off (PTO) - Central lubrication system - Central locking system - Tow bar = Additional Information = Technical Information Number of cylinders: 6 Engine displacement: 15,256 cc Drivetrain AdBlue system: Yes Fuel tank: 1,000 liters Transmission Transmission: WSK 440, 12-speed, automatic Axle configuration Brakes: Disc brakes Suspension: Leaf spring suspension Front axle 1: Tire size: 385/65/22.5; Light alloy rims; Max. axle load: 9000 kg; Steered Front axle 2: Tire size: 385/65/22.5; Light alloy rims; Max. axle load: 8000 kg; Steered Rear axle 1: Tire size: 315/80/22.5; Dual tires; Differential lock; Light alloy rims; Max. axle load: 13400 kg Rear axle 2: Tire size: 315/80/22.5; Dual tires; Differential lock; Light alloy rims; Max. axle load: 13,400 kg Dimensions Dimensions (L x W x H): 826 x 255 x 396 cm Weights Unladen weight: 14,775 kg Payload: 28,225 kg GVW: 43,000 kg Condition Technical condition: very good Visual condition: very good MAN TGX 41.640 8X4/4 BBS HEAVY DUTY TRACTOR 500 TON PUSH PULL EURO 6 L PACKAGE TRACTION 8X4 BBS LEAF SUSPENSION WHEELBASE 410 CM SLIDING FIFTH DRIVE COUPLING FOR SEMI-TRAILER TECHNICALLY PERMISSIBLE MAX. Total weight 45,000 kg Diff-locking Push and draw couplings on the front and rear of the tractor Pulse and push force 500,000 kg Auxiliary hydraulic valves and air valves Large cooling package behind the cab WSK 440 torque converter Twislocks for ballast box Tractor is workshop-tested and ready for use Ibsdpfx Agswmnqde Nec