Used Residual Ozone Destroyer for sale (876)

Condition: used, Year of construction: 2007, Prominent water treatment plant, consisting of: 1. Softening: The raw water is fed into the double softener. Only one bottle is ever in operation and the other is in regeneration or stand-by. In the softener, calcium and magnesium are replaced by sodium. The system has a volume counter that switches to the other bottle when the preset quantity is reached. Regeneration takes place with saline solution from the brine tank. The value at the outlet is 0°dH. 2. reverse osmosis: Reverse osmosis fills the permeate tank with demineralised water, so-called permeate. Depending on the raw water quality, water temperature, condition of the membrane and correct setting, different conductance values and operating pressures result. The following flow rates are set during commissioning: Permeate 600 l/h, concentrate 200 l/h, corresponding to a yield of 75%. 3. permeate tank and ozonisation: The unpressurised 500 l permeate tank has an adjustable level control. For treatment with ozone, the water in the permeate tank is circulated via an adjustable ozone feed point. The ozone is generated from air in the ozone generation system by means of a silent electrical discharge and is available as an ozone-air mixture. The air and the undissolved ozone rise upwards in the permeate tank and are discharged via the residual ozone destroyer. A redox potential and ozone measurement is carried out after the centrifugal pump for monitoring purposes. The ozone dosage is set via the touch panel. You can choose between regulation via the redox potential or the ozone concentration. Additional title: Water softening, reverse osmosis system, ozone sterilisation Permeate output: 600 l/h Concentrate output: 200 l/h Ozone output: 5 g/h Max. working pressure: 16 bar Iijdpfx Ajw Uvdgjm Dsh Current: 2 A Voltage: 230 V Frequency: 50 Hz Water: < 5 bar (cooling water) Compressed air: 5,5 - 6,5 bar (max. 10 bar); max. 0,37 Nm³/h Operation / Control: Simatic S7-300, Touch Panel Position: free standing Base construction: Fully mounted on tubular frame with spherical feet Features: Reverse osmosis unit, reaction tank complete with residual ozone destroyer, ozone generator, ozone gas warning device, ozone and redox sensor, switch cabinets with control unit

Condition: used, Little used European Spraydry Technologies model 8 - 19 Tall Form Spray 304 stainless steel ATEX rated spray dryer system. Mass balance design capabilities approximately 246kgs feed @ 10% solids with 26kgs Powder @ 5% residual moisture + 220kg/h water evaporated based on Potato Proteins. Inlet temperature 190 deg.c. with exhaust temperature 90 deg.c. Mass flowrate of drying air rated 6,895kg/hr. System includes the following parts: (1) Airco model CHP inlet fan driven by 11kw motor. (1) Lanemark model DB07 propane burner with control panel. (1) Tall form spray dryer chamber with conical base fitted with dislodging hammers fitted to cylinder and cone. Access/inspection doors. Explosion suppression bottles. (1) Stainless steel feed lance with pressure nozzle. (1) 304 Stainless steel product cyclone with explosion suppression bottles. Includes DMN Westinghouse type AL250DairyMZC-11 APS rotary lock value with motor. (1) Exhaust air chamber with explosion suppression bottle. (1) Gough type GBS550 stainless steel vibratory sifter/screen, mounted on stainless steel mobile frame. (1) Feed balance stainless steel vertical vessel. (1) FBF Italia model FBF2004/P High pressure plunger pump. (1) Mettler Toledo type V4-REM industrial flow-though metal detector with Piab conveying system. (1) Airco type CHP825 exhaust fan driven by 30kw motor. (1) Robbe model Atlas filling machine for bags with controls. Various small scale circulation pumps, pipework, instrumentation and ducting available. System has now been removed from installed production position and ready for loading Specifications: Material Of Construction: 304 Stainless Steel Type Of Spray: Nozzle Iodez D Efnopfx Am Deih

Condition: used, Year of construction: 2019, functionality: fully functional, color: other, Wood shredder in good condition. Immediately ready for use. Iiedez R I S Hopfx Am Doh The shredder was purchased from a bankruptcy estate and is now available for resale. Approximate dimensions: 110/240/285 cm, year of manufacture 2019.

Condition: used, Year of construction: 1989, functionality: fully functional, machine/vehicle number: 89A 2664, power: 18.5 kW (25.15 HP), overall weight: 1,950 kg, fuel type: electric, loading space volume: 1.6 m³, loading space width: 800 mm, loading space length: 1,000 mm, loading space height: 2,000 mm, Description For sale is a robust ZENO wood waste shredder / single-shaft shredder, type ZTLL 800 × 1000, manufactured in 1989. The machine is in good working order and was used in a wood processing facility. The shredder features an 18.5 kW main drive and a hydraulic pusher floor. The feed hopper measures 1,000 × 800 mm, and the height is approximately 2,000 mm. The rotor diameter is approximately 300 mm (type-specific), and the rotor speed is approximately 140 rpm. The machine weight is approximately 1,950 kg (type-specific). The rotor is equipped with cutting plates / individual teeth mounted on tool holders. The blades or cutting teeth are in good used condition. The rotor also shows a well-maintained condition with no significant damage visible in the provided images. It is fitted with a sturdy, reinforced perforated screen basket with a 20 mm hole diameter. The perforated screen is in very good condition. The 20 mm screening is suitable for producing a correspondingly fine, uniform shredded material. The complete electrical control system, including the control cabinet, is included in the scope of delivery. This includes, among other things, a main switch, system on/off, operating and fault indicators, forward/reverse, and control for the hydraulic pump. The control cabinet is fully present and will be sold together with the machine. The offer also includes a powerful transport fan for pneumatic transport of the shredded material. The fan motor has 18.5 kW / 25 hp, 380/660 V, 36.5/21 A, 1,455 rpm, 50 Hz, cos φ 0.86, and protection class IP54. The motor weight is 136 kg. Existing pipes and fittings belonging to the system can be taken over after inspection. This means that not only the shredder itself is offered, but a largely complete combination of wood waste shredding, control, and pneumatic material transport. The machine is particularly suitable for wood waste and production residues from carpentry shops, interior design, timber construction, joineries, and comparable wood processing companies. Inspections are possible by appointment. The location of the system is 3608 Thun, Switzerland. Sale from the location. Dismantling, loading, and transport, as well as any export and customs costs, are the responsibility of the buyer, unless otherwise agreed in writing. The machine is sold in its existing used condition as inspected. Technical specifications are provided to the best of our knowledge; errors and prior sale are reserved. Iodpfjz Ikz Ajx Am Djih Selling price: 12,500.00 EUR Price net, plus any applicable statutory taxes and duties. Export, customs clearance, and import duties are the responsibility of the buyer. Technical specifications in brief Manufacturer: ZENO Zerkleinerungsmaschinenbau Norken GmbH · Type: ZTLL 800 × 1000 · Year of manufacture: 1989 · Machine No.: 89A 2664 · Feed hopper: 1,000 × 800 mm · Height: approx. 2,000 mm · Main drive: 18.5 kW · hydraulic pusher floor · Perforated screen: Ø 20 mm, very good condition · Blades/cutting teeth: good condition · Rotor diameter: approx. 300 mm* · Rotor speed: approx. 140 rpm* · Machine weight: approx. 1,950 kg* · complete control cabinet included · Transport fan: 18.5 kW / 25 hp. * Type-specific comparison data ZENO ZTLL 800 × 1000. The specifications and condition of the offered machine are binding.

Condition: used, Year of construction: 2018, Sander Multizon ozone generator with a rated output of 120 g of ozone per hour. Technical data according to the nameplate: - Manufacturer: Erwin Sander Elektroapparatbau GmbH - Machine: Multizon ozone generator, 120 g/h - Type: - Machine no.: 2582 - Year of manufacture: 2018 - Rated output: 120 g ozone/h - Ozone concentration: 20 g ozone/m³ - Permissible operating pressure: -0.05 bar Isdoz Ri S Topfx Am Dsih - Air flow rate: 6.0 m³/h - Electrical connection: 400 V – N – PE, 50 Hz - Power requirement: 12 kVA (excluding injector pump) - Current consumption: L1 13 A; L2 5.4 A; L3 10 A - Weight: 330 kg - CE marking

Year of construction: 2012, operating hours: 4,000 h, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 363/15862010, The rotary bed dryer WB-T (model 1.00 / 3.00) from Allgaier Process Technology GmbH is a specialized industrial plant for the continuous, uniform, and gentle drying of bulk materials and biomass. In process engineering, the model designation (1.00 / 3.00) typically refers to the dimensions of the drying area, i.e., a bed width of 1.00 meter and a bed length of 3.00 meters. The heating capacity is 250 kW and is powered by electricity. Typical applications: • Biofuels & wood industry: Drying of wood chips, sawdust, and bark for pellet production. • Waste management • Agricultural & recycling industry: Processing of fermentation residues (from biogas plants), green waste, sugar beet pulp, or bagasse. Ijdpfx Amez Rz Dns Doih Operating principle: The technology combines the process engineering advantages of a drum dryer with those of a fluidized bed dryer: • Rotary bed mechanism: The wet product lies inside on a perforated flow bed (perforated sheet). A targeted mechanical movement or tumbling in combination with the airflow creates a rotating or rolling product movement ("rotary bed"). • Counter-current or cross-current ventilation: The drying air is blown from below through the sieve bed and flows intensively through the tumbling product. This ensures an optimal heat and mass exchange. Main features & advantages: • Low-temperature drying: The plant is ideally designed for operation with waste heat or low-temperature heat sources (e.g., from combined heat and power plants/CHP or industrial residual energy). • Long residence time: This enables particularly gentle dewatering of the material while simultaneously ensuring high homogeneity of the residual moisture. • Robust particle processing: In contrast to pure fluidized beds, large, irregular, or sticky particles can also be processed economically. • Integrated screening: The flow effectively reduces fine dust and sand content during the process.

Year of construction: 2012, condition: ready for operation (used), MFK DR 426 Edge milling cutter, deburring tool, chamfering tool Compressed air connection: 6 - 10 bar Turning rest diameter: max. 3 mm steel Shearing force: at 8 bar, 450 kp Dimensions: 330 mm x 300 mm x 320 mm (L x W x H) Weight: approx. 20 kg You are welcome to visit us for a demonstration. We can also arrange cost-effective shipping for you! You will receive a proper invoice. For international customers, a net invoice can also be issued. A valid VAT identification number is required. Isdpfx Amjz E U Tqs Djih Subject to prior sale. Visit our shop and browse our other offers. The company names and trademarks mentioned are the property of their respective owners and are used only for identification and description of the products. Deviations from technical data and errors in the description of the article may occur and are subject to change.

Condition: used, Year of construction: 2017, functionality: fully functional, machine/vehicle number: 1146401-001, tank capacity: 200 l, year of last overhaul: 2017, We are offering a used drum melter, model RobaDrum 200, from the manufacturer Robatech. The machine is no longer needed in our operations but was in daily use until a week ago, in conjunction with a wrapping machine (applying adhesive to foil on MDF/particleboard). The machine functions properly and is ready for immediate use. It shows some external signs of wear and has some adhesive residue, which is typical for normal industrial use, but this does not affect its operation. The machine underwent its annual maintenance by the manufacturer last summer. Isdpez Sy Smjfx Am Doih The machine was controlled via a control panel (see photo), which is included in the sale. Technical data: Manufacturer: Robatech Model: RobaDrum 200 Year of manufacture: 2017 Condition: Used, fully operational Application: Hotmelt and PUR adhesives Drum capacity: 200 liters Available for inspection in Winterswijk.

Condition: ready for operation (used), Year of construction: 2021, A stationary Brabender residual moisture and moisture content measuring device is offered. Relative measuring range: 0.0001%H₂O-15%H₂O, absolute measuring range: 0.01mgH₂O-15mgH₂O, moisture content resolution: 0.01mg, resolution: 1ppm, relative resolution: 0.0001%H₂O, measuring temperature range: 30°C-160°C, temperature setting: in 1°C increments, sample weight: approx. 0.05g-20g, max. sample volume: approx. 50cm³, accuracy: better than approx. 0.6mg, ambient temperature: +10°C to +45°C, relative humidity: 5%-95%, storage temperature: -20°C to +55°C, relative humidity: 5%-95%, measuring distance: approx. 1m, measuring height: approx. 1.6m. Dimensions X/Y/Z: 562mm/420mm/275mm, weight: 27.6kg. Documentation available. Inspection possible by appointment. Iedpszli Ursfx Am Deih

Year of construction: 2018, condition: used, This listing is for a Solaris Biotech Solution Jupiter 3.0 Fermentor. The unit is in full working condition and is ready for immediate release. The Solaris Biotech Solution Jupiter 3.0 Fermentor is a highly versatile and configurable bioreactor system, ideal for laboratory-scale applications. With advanced automation and robust design, it caters to a wide range of research and development needs, as well as small-scale production. Key Features: Autoclavable and Sterilizable Design: Ensures ease of cleaning, sterility, and reliable operation for contamination-free processes. Flexible Vessel Options: Available in various aspect ratios and thermoregulation designs, with total volumes ranging from 2.0 L to 10.0 L. Pressure Control: Handles pressures up to 1.6 bar in the 2 L and 4 L jacketed vessels, with continuous gas-in and gas-out flux. Innovative SCADA Software (LEONARDO 3.0): Provides automated management of fermentation and cultivation processes, ensuring precision and ease of operation. Parallel Management: Supports simultaneous operation of up to 24 units via a single HMI with a 24” display, streamlining complex workflows. Remote Access: Enables monitoring and control via PC, tablet, or smartphone, using QR code scanning or a dedicated web portal for remote convenience. Applications: Process Development and Optimization: Facilitates experimentation and optimization of bioprocesses for scale-up and scale-down studies. Education and Research: Suitable for educational purposes and basic research in bioprocessing. Small-Scale Production: Supports small-batch manufacturing and pilot-scale processes. Benefits: Cost-Effective Performance: Combines advanced features with affordability for laboratory and production environments. High Level of Automation: Simplifies management of fermentation and cultivation with LEONARDO 3.0 software, reducing operator workload. Versatility and Configurability: Adaptable to a wide variety of applications, ensuring compliance with validated GMP regulations. Technical Specifications: Material: VALOX resin (external) and silicone (internal) Ijdpfsxxz T Hjx Am Djih Autoclavable: 121-133°C for up to 30 minutes Residual Volume: 0.04 mL Flow Rate: 65 mL/min

Condition: excellent (used), Year of construction: 2022, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: SN210551, overall weight: 14,000 kg, type of input current: AC, input voltage: 400 V, power: 400 kW (543.85 HP), Equipment: type plate available, A MIXACO heating/cooling mixer is a combined system consisting of a heating mixer and a downstream cooling mixer, specifically designed for the processing of powders, granules, and compounds (e.g., PVC dry blends, WPC, or masterbatches). Technical specifications – summary (details can be found in the documents): Hot mixer: • Volume: 3500 liters – Usable volume: 2500 liters • Tip speed: 5-50 m/s • Made of duplex steel – 1.4462 stainless steel • Power drive with 400 kW FC controlled • Vacuum up to 150 mbar abs. Cold mixer: • Volume: 9000 liters – Usable volume: 7650 liters • Tip speed: 3.5 – 7 m/s • Made of 1.4541 stainless steel • Power drive with 90 kW FC controlled The operating principle is divided into two physically and apparatus-wise separate process phases: 1. The heating mixer phase (heating and homogenizing) • Mechanical friction: In the heating mixer, a modular mixing tool rotates at a high circumferential speed (approx. 10–40 m/s). The intense flow and vortex formation (mixing vortex) causes the particles of the mixture to rub intensely against each other. • Heating: This mechanical friction generates the necessary thermal energy directly in the product, quickly and evenly heating the material to the desired target temperature (sometimes exceeding 100 °C). • Recipe component addition: At the same time, all recipe components, such as additives, dyes, or liquids, are perfectly homogeneously distributed. An integrated aspiration system also ensures the dehumidification of the mixture. 2. The transfer • Once the target temperature defined in the process program is reached, a contoured, dead-space-free outlet opens on the heating mixer. • The hot, homogeneous mixture is transferred with minimal residue and quickly to the cooling mixer, which is located directly below or next to it. The heating mixer is then immediately available for the next batch. 3. The cooling mixer phase (gentle cooling) • Heat exchange: In the cooling mixer (available in vertical or horizontal design), the hot material is passed over cooled surfaces. Iodpsz Iww Rsfx Am Dsih • Water cooling: A targeted cooling water circuit in the double jacket (bottom and side walls) efficiently removes thermal energy from the dry blend. • Agglomeration prevention: A slow, material-friendly stirring mechanism keeps the mixture in motion until the final storage temperature is reached. This prevents caking (compaction) due to residual heat before the material is transferred to silos or further processing. Summary created with AI. The units can be inspected in operation in the Netherlands. The system for sale was used in the R&D center of UBQ for development purposes. This explains the very good condition for the low number of production hours. We also have a steel structure available for the setup. This is not included in the price. If there is interest, it can be negotiated separately. Currently, the system is located outside of Europe – we need to determine whether direct transport is feasible or whether import to Europe by UBQ is more sensible (which would allow for a sale within Europe with a reverse-charge mechanism).

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, total height: 2,000 mm, total length: 1,600 mm, total width: 1,600 mm, type of input current: three-phase, controller manufacturer: Union Dialog electronic control, compressed air connection: 6 bar, water pressure: 2 bar, Used 2018 Union MDMV 1 closed-circuit vacuum solvent degreaser, 50kg basket, Dialog control, Industrial Frigo chiller and 2 Safechem units. Manufacturer: Union Model: MDMV 1 Machine Type: Closed-circuit vacuum solvent metal degreasing / component cleaning machine Year: 2018 Condition: Excellent Includes: Industrial Frigo GR2A 30/Z industrial water chiller & 2 x SAFECHEM SAFE-TAINER chemical storage/handling units Iedpfx Ajz Itlwom Dsih Machine Description Used 2018 Union MDMV 1 industrial metal degreasing and component cleaning machine, designed for precision cleaning of small and complex metal components using super-stabilised perchloroethylene (PCE / PER / tetrachloroethylene). This is a closed-circuit hermetic vacuum solvent cleaning system incorporating washing, rinsing, vapour degreasing, solvent recovery/distillation and vacuum drying within an enclosed process. Technical Specifications Maximum Basket Capacity: 50 kg Solvent Type: Perchloroethylene / PCE / PER / Tetrachloroethylene – C₂Cl₄ Solvent Load: Approx. 397 kg / 248 litres Main Electrical Supply: 400 V / 3 Phase / 50 Hz Installed Power: Approx. 23 kW Rated Current: Approx. 46 A Steam Pressure Requirement: Approx. 4–5 bar Compressed Air Requirement: Approx. 6–8 bar Water Pressure Requirement: Approx. 2–3 bar Floor / Ground Loading: Approx. 549 kg/m² Control: Union Dialog electronic control This particular machine also has a substantial integrated solvent-management system incorporating working and recovery tanks, solvent pump, fine filtration, swarf filtration, still/distillation system, condenser, heat exchanger, separator, decanter, vacuum pump and active-carbon treatment. Continuous Solvent Recovery A particularly useful feature of the MDMV design is the continuous solvent distillation/recovery system. Union states that MDMV machines operate under vacuum for rapid washing cycles and use continuous vacuum distillation with automatic final stripping of residues, allowing contaminated solvent to be regenerated and reused during production. Industrial Frigo GR2A 30/Z Chiller Included The machine is supplied with a 2018 Industrial Frigo GR2A 30/Z air-cooled industrial water chiller. Refrigerant: R407C Refrigerant Charge: Approx. 5 kg Electrical Supply: 400 V / 3 Phase / 50 Hz Rated Current: Approx. 23 A Nominal Water Pressure: Approx. 3.2 bar Temperature Set-Point Range: -10°C to +25°C Weight: Approx. 390 kg The complete installation includes: 2018 Union MDMV 1 metal degreasing machine 50 kg maximum basket capacity Union Dialog control Closed-circuit solvent cleaning system Vacuum cleaning/drying system Rotating / oscillating basket system Spray cleaning capability Immersion cleaning capability Solvent vapour degreasing Integral solvent distillation and recovery Working solvent tank Recovered-solvent / waiting tank Solvent circulation pump Fine solvent filtration Swarf filtration Vacuum pump Condenser Heat exchanger Water / solvent separation Decanter Active-carbon vapour treatment system Floor safety / spill-containment tank 2018 Industrial Frigo GR2A 30/Z industrial chiller 2 x SAFECHEM SAFE-TAINER chemical handling/storage units Stainless steel containment trays Use and maintenance handbook Electrical documentation Please Note: All specifications, dimensions, capacities and descriptions are approximate and provided in good faith.

Condition: used, Year of construction: 2022, functionality: fully functional, For sale, starting from our location in 45888 Gelsenkirchen, are two Inject Star P-60 residual meat recovery systems, including bone crushers and accessories. These systems are used, manufactured in 2019 and 2022, and come from a business liquidation. Currently, both systems are still operational and can be inspected on-site by appointment. Iiedpfx Asz Iz Tcsm Doh Disassembly, loading, and transport are the responsibility of the buyer.

Year of construction: 2020, condition: excellent (used), The Moba CTW6500 automatic industrial machine designed to denest, wash, stack, and dry plastic egg trays at a capacity of up to 6,500 trays per hour. High Capacity: Processes up to 6,500 plastic egg trays per hour to keep up with large egg grading and processing facilities. Full Automation Cycle: Automatically performs the entire handling and cleaning sequence, including de-nesting (separating stacked trays), washing with water and detergent, drying, and stacking clean trays for reuse. Iijdoz D Uurepfx Am Doh Hygienic Design: Built for poultry farms and packing stations to meet strict biosecurity and food safety standards by removing dirt, egg residue, and contaminants Complete and in good working condition Shipping can be arranged

Condition: used, Year of construction: 2000, machine/vehicle number: 000909 / 2000, functionality: fully functional, power: 15 kW (20.39 HP), volume flow: 10,500 m³/h, filter area: 61.5 m², overall weight: 1,950 kg, For sale is a complete, stationary AL-KO PROFI-JET BG 2 dust extraction and filtration system for wood dust, manufactured in 2000. The system was used in a wood processing production facility and is fully equipped with a fan, automatic filter cleaning system, rotary airlock, silencer, frequency converter, control cabinet/controller, and extensive ductwork. The dust extraction system was operated inside the production hall, and the filtered return air was returned to the production area. The filter system has an H1 rating and, according to the label, is suitable for separating wood dust with a residual dust content of ≤ 0.2 mg/m³. Technical data of the filter system: Manufacturer: AL-KO THERM GmbH Type: PROFI-JET BG 2 Year of manufacture: 2000 Serial number: 000909 Volume flow rate: 10,500 m³/h Filter area: 62.5 m² Weight of filter system: approx. 1,600 kg Filtration: Surface filtration Filter cleaning: automatic compressed air cleaning Compressed air connection: max. 6.0 bar Filter elements: approx. Ø 120 mm × 2,500 mm length Height of filter housing: approx. 2,600 mm H1 wood dust rating: residual dust content ≤ 0.2 mg/m³ Dimensions: Length: approx. 2,400 mm Width: approx. 1,620 mm Overall height: approx. 4,500 mm Fan: Manufacturer: JKF Industri Type: JK-40 MTD L Power: 15 kW Speed: approx. 2,900 rpm Fan year of manufacture: 2000 The installed 15 kW drive motor is rated separately with 2,920 rpm at 50 Hz and protection class IP55. Frequency control and controller: The dust extraction system is equipped with a Danfoss VLT 6000 HVAC frequency converter. Complete control cabinet with Siemens controller and Siemens TD 200 operating panel included. Iodez Ikzpjpfx Am Dsih The automatic filter cleaning is carried out pneumatically via individually controlled valves. Rotary airlock: Manufacturer: AL-KO Type: ZRS 960 Rotary valve: Ø 320 mm Number of vanes: 7 Inlet: 250 × 960 mm Outlet: 208 × 960 mm Delivery rate: 47,450 l/h Motor power: 0.55 kW Speed: 12 rpm Protection class: IP54 Additional equipment: Included with the system: - Silencer, connection Ø 400 mm - Return air ducting to the production hall - Complete system control - Danfoss frequency converter - Automatic pneumatic filter cleaning - Rotary airlock - Extensive galvanized dust extraction and return air ducting Large parts of the existing ductwork can be taken over after consultation. The system is still in its assembled condition. This allows the layout, duct routing, and existing components to be inspected and documented before purchase. Location / Sale: Location: 3608 Thun, Switzerland Available: immediately Dismantling no later than: 07/31/2027 The system will be sold in its currently assembled condition. Dismantling, removal, loading, and transportation will be carried out entirely by the buyer at their own expense and responsibility. In the event of a sale to a foreign country, transportation, export/import, and customs duties will also be borne by the buyer. Inspection possible by appointment. Sold as is, without warranty. Selling price: 12,500.00 EUR Price net, any applicable taxes and duties will be added. Export, customs duties and import duties are the responsibility of the buyer.

Condition: used, This listing is for the Thermo Scientific Multifuge Pro Centrifuge Series The units are in full working condition and are ready for immediate use Iisdpfx Ameyt Naxe Dsh The Thermo Scientific™ Multifuge™ Pro Centrifuge Series (including the X4R refrigerated model) is a high-performance, versatile laboratory centrifuge designed for high-capacity, general-purpose processing. Featuring a 4-liter capacity, these units are ideal for cell culture, blood separation, and microbiologyKey Features: - Auto-Lock™ Rotor Exchange: Tool-less, push-button rotor exchange for fast application changes in under 3 seconds. - Intuitive Interface: A full-color touch screen provides easy, rapid programming, with storage for up to 100 programs. - Versatility & Capacity: Compatible with up to 18 different rotors (swing-out and fixed-angle) with a maximum speed of 15,200 rpm (up to 25,830 x g). - Sample Protection: ClickSeal™ biocontainment lids provide certified, glove-friendly, snap-on sealing for safety. - Efficient Design: The X4R refrigerated model includes a powerful cooling system for temperature-sensitive samples, with a range of -10°C to +40°C. - SMARTSpin™ Technology: Advanced rotor management optimizes acceleration, braking, and residual load imbalance.

Condition: used, This listing is for a QuattroFlow QF150 Diaphragm Pump. The unit is in full working condition and is ready for immediate release. The Quattroflow 150S is a 4-piston Diaphragm pump, which is mainly used to pump water-like fluids that are typically handled in research-, pilot plant- or production facilities of the pharmaceutical, biotech,food or cosmetic research centres or plants Examples: • Solutions containing proteins (albumin, IgG, Clotting factors, monoclonal antibodies, enzymes, vaccines.) • Solutions of polymers or suspensions (silicon, latex, chromatography media) • Cell suspensions (bacteria, yeast, algae, fungi, mammalian cells) • colloidal solutions • Suspensions of viruses or phage • Dairy products • Gelatine • Supplements and ingredients for cosmetic and food Flow rate max.: Eccentric shaft 3° l/h (lpm) 100 (1.67) 100 (1.67) Eccentric shaft 5° l/h (lpm) 180 (3) 180 (3) Flow rate min.: Eccentric shaft 3° l/h (lpm) 1 (0.017) 1 (0.017) Eccentric shaft 5° l/h (lpm) 1 (0.017) 1 (0.017) Pressure: Temperature of fluid < 40°C bar (psi) 6 (87) 6 (87) Temperature of fluid > 40°C bar (psi) 4 (58) 4 (58) Temperature max.: Fluid °C (°F) 80 (176) 80 (176) CIP °C (°F) 90 (194) 90 (194) SIP °C (°F) 130 (260) 130 (260) Autoclave °C (°F) 130 (260) 130 (260) Suction lift dry at: 3000 rpm 3000 rpm Eccentric shaft 3° m (ft) 1-1,5 (3.2-4.9) 1-1,5 (3.2-4.9) Ijdpfxexx Avpe Am Doih Eccentric shaft 5° m (ft) 2-3 (6.6-9.8) 2-3 (6.6-9.8) Volume specifications: Approximated volume per revolution at free output ml 0,72 (3°) 1,2 (5°) 0,72 (3°) 1,2 (5°) Filling volume without connectors ml 15 15 Residual volume (after idle with highspeed motor) ml 1-3 1-3 Product wetted surface (approx.) cm² (inch²) 112 (17) 112 (17) Speed range pump rpm 10-3000 10-3000 Connection specification inlet (standard) Connector " 1/4" TC 1/4" TC Flange diameter mm (inch) 25 25 Internal diameter mm (inch) 4,7 4,7 Connection specification outlet (standard) Connector " 1/4" TC 1/4" TC Flange diameter mm 25 25 Internal diameter mm (inch) 4,7 (0.19) 4,7 (0.19) Position of connectors Inline Inline Number of flow directions 4 4 Diameter drive shaft mm 7 7 Product wetted materials (standard): Pump housing SS316L SS316L Valve plate SS316L SS316L Diaphragms Santoprene Santoprene Valves EPDM EPDM O-rings EPDM EPDM Non-product wetted materials (standard): Pump housing SS316L SS316L Bearing housing SS316L SS316L Base plate SS316 SS316 Hood SS316 SS316 Dimensions pump with motor and housing: Length mm (inch) 257 (10,2) 277 (10-91) Width mm (inch) 164 (6,5) 200 (7,87) Height mm (inch) 185 (7,2) 195 (7,67) Weight pump with motor and housing kg (lb) 9,8 (22) 11,2 (25) IP protection class pump IP 54 54 Operating temperature range °C (°F) 0…40 (32…104) 10…30 (50…86)

Condition: used, functionality: fully functional, Year of construction: 1994, Residual concrete recycling plant Feeding with screw conveyor Pumps Iiedpfoywn U Rjx Am Doh Agitators

Condition: ready for operation (used), Year of construction: 2016, laser power: 2,000 W, travel distance X-axis: 3,070 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 100 mm, table load: 920 kg, number of axes: 3, This 3-axis AMADA LCG 3015 AJ fiber laser cutting machine was manufactured in 2016. It features a maximum continuous laser power of 2,000 Watts and an impressive X-axis travel of 3,070 mm. The machine includes an automatic palletizing system and a lightweight HS cutting head with advanced safety measures. If you are looking to get high-quality cutting capabilities, consider the AMADA LCG 3015 AJ machine we have for sale. Contact us for further details. • CNC control: AMADA AMNC-F with 15" touchscreen, 1 MB memory • Control features: Auto-diagnostic system, laser power feedback control, USB/Ethernet ports, CD drive, LAN interface, cutting data library database, part/sheet counting, logical search function, production time measurement • Max material thickness: • Mild steel (ST 1203): 10 mm • Stainless steel: 10 mm • Aluminum (AlMg3): 8 mm • Copper: 4 mm • Brass: 5 mm • Cutting speed: 0–120 m/min • Machine weight (with interchangeable table): 8,200 kg • Cutting head: Lightweight HS head with capacitive sensor for constant distance, rapid-change lens/nozzle system, 5 protective safety measures • NC focusing function: Automatic focus adjustment via CNC and optics for varying materials/thicknesses • Positioning diode laser: Assists in approaching positions and working with residual sheets/trimmings Additional equipment • Pallet changer: Automatic palletizing system with pneumatic thin-sheet clamping and roller table for easy positioning Iodpfx Ajz S Nfcjm Djih • Extraction and chiller: Multi-chamber extraction with self-cleaning filters; closed-loop cooling unit for laser, focusing mirror, lens, and drives

Condition: good (used), Year of construction: 1997, Residual oxygen measuring device for checking the gas volume in insulating glass. Iedpfx Amji Azc Aj Doih Dimensions: Depth: 270 mm Width: 204 mm Height: 180 mm Weight: 5.7 kg

Condition: used, Year of construction: 2019, operating hours: 196 h, functionality: fully functional, machine/vehicle number: W09D013KWKAD43636, operating pressure: 500 bar, total length: 2,910 mm, high-pressure hose length: 500 mm, total height: 1,770 mm, total width: 1,720 mm, pressure: 500 bar, empty load weight: 760 kg, fuel: diesel, heating capacity: 115 kW (156.36 HP), overall weight: 760 kg, water tank capacity: 300 l, fuel tank capacity: 70 l, power: 13 kW (17.68 HP), temperature: 95 °C, volume flow: 0.9 m³/h, noise level: 104 dB, pressure (max.): 500 bar, Equipment: chassis, crane, This well-maintained DYNAJET 500th 15 HELI hot and cold water high-pressure unit is available for immediate delivery. Manufactured in 2019 and having only 196 operating hours, the machine is in excellent condition and is being delivered fully serviced, fully functional, and ready for operation. Designed for demanding industrial cleaning applications, the DYNAJET 500th 15 HELI combines powerful cleaning performance with compact dimensions, low weight, and excellent mobility. With an operating pressure of up to 500 bar and hot water temperatures up to 95°C, the machine is ideally suited for removing heavy contamination, coatings, grease, and industrial residues. The unit is equipped with a reliable Kubota diesel engine, integrated hot water system, and a large 300-litre water tank for independent operation even where external water supply is limited. The trailer-mounted design ensures maximum flexibility and easy transportation between jobsites. To ensure many years of reliable operation, the machine will be supplied with a brand-new 50 m high-pressure hose. A turbo nozzle and standard flat-jet nozzle are included in the sale. Iiodpfxoz Nd Nde Am Deh Key features and advantages: * Year of manufacture: 2019 * Only 196 operating hours * Fully serviced before delivery * Fully functional and ready for operation * Maximum operating pressure: 500 bar * Flow rate: up to 15 l/min * Hot water temperature up to 95°C * Powerful Kubota 3-cylinder diesel engine * Integrated hot water system with high-performance burners * 300-litre integrated water tank * Approx. 70-litre fuel tank * Trailer-mounted unit with overrun brake * New 50 m high-pressure hose included * Turbo nozzle included * Standard nozzle included * Compact, robust and easy to transport *Ideal for industrial cleaning, surface preparation and professional service applications Please contact us if you are interested or would like to receive further information, pricing details, additional photos, or arrange a viewing of the machine. We will be pleased to assist you.

Condition: good (used), Year of construction: 1998, Measuring device for checking the gas volume in insulating glass. Width: 204 mm Height: 180 mm Ijdpfeyll H Eox Am Dsih Depth: 270 mm Weight: 5.7 kg

Condition: used, This listing is for a Bioquell L-4 Opti Vapor Hydrogen Peroxide (VHP) Generator The unit is in full working condition and ready for immediate use This vapor hydrogen peroxide (vhp) generator is a high-quality lab instrument manufactured by Bioquell (Model: L-4). Provides highly effective, residue-free bio-decontamination of rooms and enclosures for critical life science applications. It has been sourced directly from a working facility, offering premium performance and dependability for standard laboratory applications while ensuring a cost-effective alternative to purchasing brand new equipment. Transparency Report and Technical Audit: Software and Media Disclosure: As a Direct-from-Lab asset, any original software media or accessories found with the unit are included as a courtesy. Licensing Notice: We do not provide, transfer, or guarantee software licenses or keys. The buyer is responsible for all software licensing, registration, and workstation compatibility via the manufacturer. Notice for Procurement: This unit is sold As-Is. While we verify the power-on status and physical integrity, we do not perform analytical validation, fluidic testing, or operational calibration. Ideal for labs with in-house technical expertise or existing service agreements. Sustainability Impact: Iiedszuf Umspfx Am Deh By choosing Direct Reuse, your facility avoids the carbon footprint of new manufacturing and prevents specialized materials from entering waste streams. Direct-to-Lab reuse is the most carbon-efficient way to equip a modern laboratory. Source Pedigree: Biotech / Research Facility Condition: Direct-from-Bench (Decontaminated/Original) Integrity: 100% Original Parts (Non-Refurbished)

Condition: used, This listing is for a Watson Marlow 620S/R Peristaltic Pumps The units are in full working condition and ready for immediate use Design & Functionality The 620S/R model is part of the 600 Series of cased peristaltic pumps featuring a brushless DC motor equipped with digital keypad control (620S) and a sturdy NEMA 2 / IP31 vented, wipe‑down enclosure suited for dry industrial environments ,It operates at dual voltage (100–120 V or 200–240 V, 50/60 Hz) and includes features like MemoDose for one-shot dosing and wireless guard-switching for safety The casing is chemically resistant, with powder-coated die-cast aluminium construction and an easy-to-clean membrane keypad Pump Performance Flow range: 0.00026 to ~4.23 gpm (equivalent to ~0.001 to 16 L/min) with the 620R pump head With newer 620RE LoadSure heads, the flow increases up to ~4.76 gpm (0.004–18 L/min) Pressure capability: Up to approximately 60 psi (4 bar) with the appropriate head and tubing Control accuracy: Exceptional 2,650:1 turndown ratio, fine speed control from 0.1 to 265 rpm in selectable increments (0.1, 0.5, 1, 2, 5, or 10 rpm), with 0.1% speed accuracy Pump Heads & Tubing Iijdpfx Aoxhdx Dem Djh The model supports the following interchangeable pump heads: 620R Mk II (continuous tubing, two rollers) 620RE and 620RE4 (LoadSure elements, two or four rollers) These heads are compatible with various tubing materials (e.g., Marprene™, Bioprene™, Sta‑Pure™, silicone) and sizes (typically 6.4 mm to 17 mm inner diameter) The 620RE and RE4 heads feature retractable rollers for easier cleaning (CIP/SIP) and rapid loading AFAB Lab Resources - Used Lab Equipment Physical Attributes & Construction Ingress Protection: IP31 (NEMA 2) for the standard 620S/R; there are IP66/NEMA 4X variants (e.g., 620SN/R) for environments requiring better dust and water resistance Weight: Around 19.6 kg (with 620R/RE head) to 20.1 kg (with 620RE4) Sound level: Less than 70 dB(A) at 1 m—relatively quiet for continuous industrial operation Advanced Features MemoDose: Delivers precise single-shot volumes—ideal for dosing applications Ramp function & non‑drip: Ramp improves handling of delicate fluids, preventing splashes/frothing, while non-drip minimizes residual drips at dose end (noted in related Di versions but often included in feature suites) Data export: Some models (e.g. 620S/RE) support RS‑232 export of batch records—important for GMP compliance

Condition: good (used), Year of construction: 2019, Professional automatic packaging machine, also suitable for large packages. For example, for packaging food, technical articles, printing and paper products, household and toy goods, and textiles. -Up to 10 programs can be stored via the display. -Automatic welding frame movement. -Automatic residual film winding. -Automatic product discharge via the outfeed conveyor. -Process start manually via a push button. Alternatively, automatic process start is possible by entering a time interval on the display. -Conveyor belt can be adjusted steplessly in height via a hand crank. -Welding frame approximately 870 x 620 mm. -Maximum package length approximately 850 mm. -Maximum package width approximately 600 mm. -Maximum package height approximately 300 mm. -Welding frame movement is electrically powered. -Water-cooled welding unit (closed system). -Maximum film roll diameter 300 mm. -Maximum film width approximately 800 mm. -Perforation possible via 3 adjustable needle rings. -Roll holder can be moved separately. -Product insertion can be adjusted separately. -The machine can be moved or secured via lockable castors. -Machine dimensions approximately: Length 2 m x Width 1 m x Height 1.5 m. Iisdpfez Sn Tfjx Am Doh Multilingual documentation including operating instructions, spare parts lists, and circuit diagrams is included in the scope of delivery. The machine can be demonstrated while powered.