Used Rollover Plate for sale (12,618)

Condition: used, Bed plate 10ft x 5 ft x 4000kgs (approx) - Matched Pair Ljdeywziuspfx Ac Aohh

Condition: used, functionality: fully functional, machine/vehicle number: 2550X10.14MM, control type: manual, degree of automation: manual, actuation type: mechanical, number of rollers: 3, roller (top) diameter: 300 mm, side roll diameter: 280 mm, roller diameter: 400 mm, roller length: 2,550 mm, working width: 2,500 mm, working height: 800 mm, sheet thickness (max.): 14 mm, sheet thickness stainless steel (max.): 10 mm, input voltage: 380 V, input frequency: 50 Hz, Equipment: centralized greasing system, cone bending device, emergency stop, swiveling upper roller, 3 roll 2500x14 mm Plate bending machine Model OMCCA ITALY CAPACITY plate width 2500 mm plate thickness 14 mm pre-bending 10 mm --- Useful rollers width 2550 mm Top roll d 300 mm Side rollers D 280 mm hard surface of the 3 rolls centralized gear unit side rolls driven Opening front hydraulic drop-end to unload the closed shell. Lhsdpey Aubuefx Ac Aoh Extended shafts to take installation of add-on molds for section bending Variable speed rolling up to 5 mtr/min power electric motor 20Hp on hydraulic unit console with electric push buttons commands. Dial gauge position rollers readout safety installations with emergency stop

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, roller diameter: 60 mm, working width: 1,050 mm, sheet thickness (max.): 1 mm, roll metal bending machine Isitan 1050 X 1.2mm Manual 3 roll Bending Machine, excellent condition for sale manufacturer: Isitan 1050X1.2 max sheet width: 1050mm Ljdpowk Rlxefx Ac Ajhh max sheet thickness: 1.2 mm Wire grooves at the ends of the rollers Conical bender roller diameter: 60mm Upper roller removable for easy workpiece removal machine dimensions: length: 130cm height: 100cm width: 65cm weight: 240kg

Condition: used, functionality: fully functional, machine/vehicle number: 7FBMF35-16267, Year of construction: 2013, operating hours: 6,500 h, load capacity: 3,000 kg, lifting height: 4,700 mm, fuel type: electric, mast type: triplex, Electric Forklift Truck – Toyota Year of manufacture: 2013 Technical data: • Model: Toyota 7FBMF30 • Load capacity: 3,000 kg • Drive: Electric (battery powered) • Mast type: Triplex with free lift • Lift height: approx. 4,300 – 4,800 mm • Fork length: 1,070 mm (standard) • Tyres: Solid rubber Lodpfx Acjw Hhwwj Ajhh • Cabin: Open design, optionally with driver protection roof • Condition: Used, serviced and fully functional

Condition: used, Cast iron bed Length: 2300 mm Lodpfxswtc Hgj Ac Aohh Width: 1900 mm Thickness: 200 mm Height on feet: 980 mm 5 T-slots horizontal and vertical T-slots dimensions: 60 x 35 mm Square dimensions: 365 x 365 mm Crack at a longitudinal T (see photo) Weight: approx 3 T

Condition: used, Cast iron bed 2600 x 2000 x 350 mm Length: 2600 mm Width: 2000 mm Lsdpfswlhfljx Ac Aohh Thickness: 350 mm 8 T-slots T-slots dimensions: 55 x 35 mm Slots spacing: 250 mm Equipped with 12 leveling feet Weight: approx 4,5 T

Condition: used, Cast iron bed 2600 x 2000 x 350 mm Length: 2600 mm Width: 2000 mm Ljdpjwlhd Uefx Ac Aohh Thickness: 350 mm 8 T-slots T-slots dimensions: 55 x 35 mm Slots spacing: 250 mm Equipped with 12 leveling feet Weight: approx 4,5 T

Condition: good (used), Cast iron bed - Floor Plate Lhodpfx Acsh Auahs Ash Useful surface (L x W x H): 3600 x 1200 x 300 mm 4 T-slots: width 44 x 26 mm Equipped with Levelling feet Weight: approx 3 T

Condition: used, Cast bed Length: 2410 mm Width: 1500 mm Thickness: 550 mm 8 T-slots 50 x 27 mm with 2 opening (possibility to close them) 1 opening L 560 x W 500 mm 1 opening L 480 x W 360 mm Ledpfxswnfz Nj Ac Aehh Weight: approx 5 T

Condition: good (used), Top of the range plate washing system for high throughput. Has come from Wembley Football Stadium where it was washing plates for the hospitality areas. Lovely condition and with options Ledpfxovd Eiys Ac Aehh

Condition: good (used), Year of construction: 1999, CNC PUNCH / DRILL / SHEARING LINE for angle and plates. TECHNICAL DATA. PUNCH INSTALLATION. MATERIAL SPECIFICATION material sample steel 52 plate size (MM) X (MM) max 300 x 25 material sample steel 37 plate dimension (MM) X (MM) min 60 x 6 max 400 x 20 angle line dimension min 50 x 50 x 5 max 150 x 150 x 5 Punch information TYPE P2- XXX-XX number 2 TYPE P3-XXX-XX number 3 Lodpfxovkphge Ac Ashh TYPE P5-XXX-XX number 5 punching capacity tonnage 110 punching diameter (mm) x thickness (mm) max 32 x 20 Shear UNIT Shear tonnage 180 Capacity max 400 x 20 Stamping UNIT Total number of characters number 40 Maximum number of characters per operation 12 CONNECTION VALUES Voltage 3 phase + Neutral + Earth V 3 X 400 Fuse A 63 slow Power KW 25 Frequency HZ 50 Permitted m-axis tolerance mains voltage % +/- 10 Field rotation Right Air pressure bar 6-8 Air capacity m2 / hour 250

Condition: good (used), Year of construction: 2017, Sahinler 4R HSS 20-280 Hydraulic 4-roll plate bending machine – Year 2017. Lhodpfx Acexau D Ij Aoh Bending length 2050 mm Max. bending capacity - mild steel 20. Upper roll diameter 280 mm Lower roll diameter 280 mm Lateral roll diameter 220 mm Bending speed 1,5 / 5 m/min. Motor power 16 kW

Year of construction: 2012, condition: good (used), Ficep Gemini HD36 GANTRY PLATE PROCESSING CENTRE, AUTOMATIC CNC DRILLING, MILLING AND THERMAL CUTTING SYSTEM, serial no. 33275, year of manufacture 2012, 127mm max. thickness, 520N/mm² tensile strength, with fitted eight head tool holder, Hypertherm HyPerformance plasma HPR260XD power supply unit, galvanised steel ducting, Autchazioni AVV.2KW fume extraction unit, approx. 3.5m x 1.75m x 3.9m high, machine bed approx. Lsdpeivfc Rsfx Ac Ashh 9.4m x 3.8m wide

Condition: excellent (used), Year of construction: 2012, · V200 Plate drilling machine (executed with a VD40 drilling unit and an X-Y coordinate table). · VTC 8/40 tool changer (8 places). Ljdpfowphgdsx Ac Ajhh · Hydraulic numbering unit VN 1/16 · Deburring unit VDB 2 (each hole is automatically deburred). Max. length 1.400 mm* Max. width : 1.000 mm Min/max. thickness : 3 - 60 mm Capacity : : 600 kg * Longer lengths (max. 2 400mm) possible by automatic repositioning.

Condition: used, functionality: fully functional, Year of construction: 2008, Peddinghaus FDB 1000/3 – CNC Plate Drilling & Profiling System– Year 2008 6 metres x 1 metres Capacity. Maximum workpiece width 1000 mm. Maximum workpiece thickness 50 mm. 3 x drilling spindles. Maximum drilling diameter 40 mm. Oxy‐Fuel. Ljdpfx Ajy E N Hdoc Aohh Hypertherm Plasma. Kemper Extraction Unit

Condition: used, (8) Angle plates as detailed. 112779 600mm x 500mm 1800mm Angle Plate 112780 600mm x 500mm 1800mm Angle Plate 112781 600mm x 500mm 1800mm Angle Plate 112782 910mm x 700mm x 1800mm Angle Plate 112783 840mm x 690mm x 3370mm Angle Plate Lhjdpfsyi Tbfjx Ac Ash Fitted with cranked riser block allowing movement of top angle plate. 112787 1020mm x 1010mm x 4280mm Angle Plate 112789 800mm x 750mm x 1190mm Angle Plate 112791 600mm x 500mm 1800mm Angle Plate

Condition: excellent (used), Year of construction: 2009, roller diameter: 1,000 mm, overall weight: 800 kg, total length: 1,880 mm, total width: 1,100 mm, total height: 1,640 mm, HIGH Output of round shaped metal parts Can be used rolling bend segments, T-Pieces, Nipples, Tubes Automatic feeding tab;le Cutting speed 2 - 10 M/Min Max. out side diameter 1000 mm Rolling width: 1000mm Rolling thickness prebending:1mm Ljdpfxjzgugvo Ac Ashh Length: 1880mm Width: 1100mm Height: 1640mm Weight: 800kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 2004, Number of T slots: 8 + 3 Jump from T to T: 280mm T size: 22mm Lsdpfxewu D Afj Ac Aohh Number of matching pieces:5 Length: 1250mm Width: 750mm Height: 2500mm Weight: 2900kg

Condition: used, sheet width 2540 mm plate thickness 2.00 mm thickness at "Niro-steel" 1.25 mm no. of strokes max. 63 Hub/min cutting angle 1.13 Grad table height 750 mm table width 320 mm distance between columns 2620 mm back stop - adjustable 5.0 - 550 mm Control konv. engine output 3.0 kW weight of the machine ca. 1600 kg range L-W-H 3100 x 1980 x 1400 mm Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - manual back stop, with analogue display Lsdpoxacftefx Ac Aehh * adjustable from the front * stepless adjustment over the entire travel range - recessed grips in the support table - 1x hold-down bar - 1x side stop - 3x support arms - 1x freely movable foot switch - operating instructions (PDF) Special accessories included: - sheet metal holding device for thin sheet metal cuts

Condition: ready for operation (used), Year of construction: 2021, sheet width 6020 mm plate thickness 6.0 mm thickness at "Niro-steel" 4.0 mm Ljdexaa Dgopfx Ac Ajhh back stop - adjustable max. 1000 mm work height max. 1030 mm no. of strokes 5 - 10 Hub/min cutting angle 0.5 - 3.0 ° down holder 33 Stück Control SC 100 T engine output 11.0 kW weight of the machine ca. ca. 27000 kg range L-W-H 7650 x 2400 x 2885 mm New price in 2021 ~ 160.000 Euro Special price upon request - in checked conditions - machinevideo - ?v=qH3uqGNZZp8 Equipment: - Robust electro-hydraulic guillotine shear * Design: Guide rail - HACO CNC control model SC 100 T, pivoting at the front left * Control unit with LCD display * Pre-selected positioning of the backgauge * Digital display of actual position * Electro-hydraulic cutting angle adjustment * Electro-hydraulic cutting gap adjustment * Programmable retraction from the backgauge * Programmable cutting length limitation * Automatic + manual programming mode * Emergency stop switch - CNC electro-motor-driven material/backgauge * On recirculating ball screws * Continuous adjustment up to max. 1,000 mm - CNC electro-hydraulic cutting gap adjustment - CNC electro-hydraulic cutting angle adjustment - Hydraulically operated Material/sheet metal clamp - Front finger guard - Front support table with recessed grips - 1x side stop with mm scale - 1x freely movable foot switch - Rear safety device (light barrier) - Operating instructions (PDF) Optional accessories included: - Sheet metal holding device for thin sheet metal blanks * Optimal positioning of thin sheet metal

Condition: good (used), Clamping plate, marking-spotting plate, measuring plate, measuring table, welding table, welding table, straightening plate, marking plate, straightening table -Clamping plate: on a solid base frame, with vice -Clamping surface: 2000 x 1000 mm -Table height: 925 mm -Plate thickness: 115 mm -Vice: clamping jaws: 150 x 30 mm clamping width 250 mm -Transport dimensions: 2480/1000/H1110 mm Lhodoxm Sagepfx Ac Ajh -Weight: 1850 kg

Condition: good (used), functionality: fully functional, Year of construction: 2012, MG SRL MH 316 C 4 Roll Plate Rolling Machine- Year 2012. Lhsdpfx Aezc Rkwec Aeh 4-roll plate bending machine. 3000 mm up to 16 mm. Upper roll diameter 340 mm. Lower and lateral rolls 310 mm.

Condition: used, functionality: fully functional, Year of construction: 2013, MG SRL AR 140 Profile Bending Ring Rollers- Year 2013. Specifications Shaft Ø140 mm Number of rolls 3 Resistance moment 130 CM³ Capacity flat 220 x 50 x R=2000 mm Horizontal and vertical Yes, Horizontal + Vertical . Stroke X-Axis 400 mm Capacity Tube 180 x 4 x R=4000 Ø x mm Capacity bar 80 x 80 x R=1000 mm Capacity HEA-Profile 180 x R=1800 mm. Lhodjzc N Rcepfx Ac Aeh Dimensions Length 2100 mm Width 1900 mm Height 2100 mm Weight 6500 kg

Condition: used, Year of construction: 1997, sheet width 0610 mm plate thickness 1,5 mm distance between columns 650 mm front stop - adjustable 0- 300 mm angle stop 45-90 Grad operating pressure 6 bar strokes per minute 60 total power requirement 3 kW weight of the machine ca. 0,27 t Ljdpexu Nrpofx Ac Ashh dimensions of the machine ca. 1 x 1 x 1,5 m

Condition: used, Year of construction: 1971, sheet width 2000 mm plate thickness 16 bei St 42 mm passage width 2250 mm impact length 1000 mm blade length 2005 mm throat 600 mm cutting gap adjustment 0,05 - 0,95 mm cutting angle 1° 40' ° down holder 10 Stück back stop - adjustable 10 - 1000 mm Ledpfeww Nccex Ac Ajhh table: 2500 x 700 table height over floor 800 mm quantity of oil 900 l weight of the machine ca. 10 t dimensions of the machine ca. 3 x 2,3 x 2,3 m voltage 380 V Food switch, material support beams, spare knifes.