Used Staircase Formwork for sale (89)

Condition: new, axle configuration: 3 axles, Year of construction: 2022, Equipment: ABS, Technical Data for EBERT TLS 43 ATV Special Low Loader: Permissible king pin load: 19,000 kg Permissible axle load: 36,000 kg Gross vehicle weight: 55,000 kg Unladen weight (per DIN): approx. 15,500 kg Lower deck length i.L.: approx. 6,650 mm + 4,000 mm Axle table length: 3,550 mm External width: 2,550 mm Loading edge/lower deck: approx. 200 mm – 350 mm Sliding table length: 500 mm Lower deck widening to: 3,050 mm Lower deck extendable by: 4,000 mm B-dimension: 13,300 mm Entire vehicle flame-sprayed galvanized, with epoxy primer and 2K paint finish Oversize warning signs front and rear, with red/white panels Wheels: 13 x Michelin 245 / 70 R 17.5 X MULTI T VB 143J/146F Steering: TRIDEC DLS with Tritronic Iiodpjyfu N Aefx Apnjb Axles: 12,000 kg – DLS single wheel suspension, hydraulic steering and hydraulic suspension Front high-bed: Side panels 600 mm high Corners at front of high-bed angled Exterior-access doors in front corners (left and right) Lockable storage box with lid behind the front wall; height 600 mm, width 2,480 mm, depth 7,500 mm Spare wheel on high-bed, right side behind partition wall Staircase on right side for access from lower deck to front high-bed Hydraulic coupling for uncoupling on left side (6-way multi-faster coupling) 6 external lashing points, 3,000 kg each (fold-down lashing eyes) on high-bed 2 lashing points, 5,000 kg each, on upper longitudinal beams (to the rear) Lower deck: Climbing aids at the boom – pull-out Outer frame thickness 8 mm Lower deck extendable by 4,000 mm, lockable every 500 mm With sliding table, lockable every 250 mm 28 external lashing points, 10,000 kg each, on the outer frame 24 plug-in sockets 90 x 90, evenly distributed for lower deck widening to 3,050 mm Between extension beams, 50 mm hardwood planks are placed, protruding by 10 mm Rear high-bed: Front of rear high-bed sloped and perforated to allow retrofitting of ramp mount profiles (galvanized adapters) At rear: ramp mount profiles (Altec) – C rails 8 external lashing points, 10,000 kg each, on rear high-bed 6 lashing points, 5,000 kg each, in the excavator recess 10 lashing points, 5,000 kg each, for oversize loads on the outer frame Excavator recess can be closed at front and rear with insertable wooden floor plates Electrics: Use NATO spiral cable; power supplied by tractor unit Roof beacon centered at rear LED side marker lights Standard vertically mounted taillight (LC5) Work lamp on the high-bed to illuminate the lower deck Oversize warning signs front and rear, with controls for uncoupling, safety sensor, and suspension pressure switch Air: Aluminum air reservoir 80 l TEBS modulator Slide-out lock left and right (valve located at rear high-bed sides) Double release valve Hydraulics: Hydraulic system on high-bed for steering, suspension, and detachable gooseneck Accessories: 2 x 4 pieces hardwood planks for lower deck widening and intermediate table 2 wheel chocks for uncoupling 4 wheel chocks On request, we can provide a leasing or financing offer. Mr. Ebert (phone...) will be happy to assist you. Further information can be found on our homepage. Subject to errors and prior sale.

Condition: good (used), functionality: fully functional, machine/vehicle number: 804, roller length: 2,550 mm, working width: 2,500 mm, sheet thickness (max.): 16 mm, sheet thickness steel (max.): 16 mm, overall weight: 12,500 kg, 3-roll hydraulic plate bending machine 2500 x 16 mm Manufacturer: KUMLA Iisdpfx Aevxbm Rjpneb Type: PV 7 H Serial no.: 804, overhauled in 1987 The machine is of a very robust design and has only been used in single-shift operation. Max. bending length: 2500 mm Max. sheet thickness: 16 mm Cone bending device Top roll diameter: 324 mm Bottom roll diameter: 305 mm Hydraulic roll adjustment Dimensions: L x W x H = 5000 x 1600 x H 1900 mm Working height: 1000 mm Additionally, a staircase platform around the machine can be purchased.

Condition: good (used), Year of construction: 1998, functionality: fully functional, Stair milling machine. To be sold due to new 5-axis CNC Milling length mm 4,750 Milling width mm 900 Passage height mm 150 Table length mm 6,000 Aggregate can be rotated by ° 70 Grooving aggregate can be tilted by ° 90 Number of aggregates 1 Main motor kW 4 Version stationary machine Adjustment program control Laser aiming light single laser CE mark yes Weight approx. kg 2,250 Available at short notice, from location Absolutely functional To be sold due to new 5-axis CNC Pictures can be provided later. Instructions will be given upon collection (not difficult) Milling stair stringers for each staircase in 1 hour possible. Long stringers, up to 470cm can be milled without any problems. 4 pressure bars Adjust the bevel, adjust the step thickness, adjust the slope (1 minute total) and off you go. The machine automatically jumps from step to step. For and as an emergency milling machine, it is still absolutely top notch Isdpfxsiwa Rko Apnjib

Condition: new, mileage: 10 km, power: 132 kW (179.47 HP), fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, loading space length: 4,100 mm, loading space width: 2,100 mm, loading space height: 2,300 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, New German vehicle: Without registration * German papers * elec. Exterior mirrors/ heated * Radio with Bluetooth * Multifunction steering wheel * Electric windows * Roof spoiler incl. side spoiler * Reversing camera incl. 7" monitor Body: * Interior dimensions approx. L x W x H = 410 x 210 x 230 cm. * Loading height at the doors approx. 10 cm lower than the load compartment height * Outer walls 25 mm. * Roof 25 mm. * Double wing door at the rear Iedpfx Apjfq I Uvenoib * Floor 16 mm. Multiplex board * Furniture staircase, extendable with 5 steps Option: * Side door * Tail lift Load securing also available from us: * Tensioning and lashing straps * Locking beams * Warning vests * Transport boxes * Edge protectors * Dunnage bags * Wheel stoppers * etc. Financing and leasing possible We manufacture bodies of any size on any chassis. Tarpaulin, GRP sandwich, aluminum. visit us at: Bodies - Complete vehicles - Trailers - Advice - Financing Subject to errors and prior sale, no liability for printing and input errors.

Condition: not inspected (used), Year of construction: 1984, 1 milling unit 2.8/3.5 kW nominal current 6,4/9,3 A Iedpfx Aoga Tu Dspnjib workpiece thickness max. 130 mm Lateral table for routing work

Condition: used, functionality: fully functional, Aluminium staircase bridge Iodpfx Apsw Nhn Hensib The staircase bridge stands out with its ease of operation and sturdy construction. It ensures straightforward use and safe access both up and down. The robust design guarantees durability and reliability with every application. The staircase bridge is already packed (see pictures) and ready for shipment. Packing dimensions: 270 x 130 cm Technical specifications: • Number of steps: 5 • Material: Aluminium • Total weight: approx. 140 kg • Packing dimensions: 270 x 130 cm

Condition: used, Working width 3450 mm Working height 2000 mm Number of cylinders 5 St. loading dimensions L x W x H 3600 x 1200 x 2720 mm Hess "Multipress" Perforated Plate Press For all sloped, segmental, and round-arch windows and doors. Also for interior work or frame construction. For gluing staircase block joints and much more. Largest working area approx. 3450 x 2000 mm External dimensions approx. 3600 x 1200 x 2720 mm The vertical perforated plate press is constructed of heavy-duty, torsion-free steel. Thanks to its simple, robust, and economical design, it has a long service life. Iiedowqr R Aepfx Apnsb The perforated plate is made of 10 mm sheet steel with a 50 mm hole pattern. The pressure cylinders and abutments are self-locking. 5 plug-in hand hydraulic cylinders on a perforated plate with a built-in pump, 2000 kp pressure relief valve, 140 mm pressure plate width, 80 mm pressure plate depth, 60 mm cylinder stroke 4 fixed individual abutments (Technical specifications according to the manufacturer - no guarantee!)

Year of construction: 2023, condition: new, Machine equipped with complete formworks (rotating hade, 5 steel rings, outer formwork) for pipe with diameters: Dint=1000mm si Dint=800mm; - The equipment can manufacture unreinforced concrete pipes with connection sockets: Dint=1000mm; Dint=800mm; Dint=600mm; Dint=500mm; Dint=400mm; Dint=300mm; - Maximum height of pipe: 1000mm; minimum height of pipe: 250mm - Vertical translation of the rotating head – electric engine - Variable revolution of the rotating head (frequency converter) - Sizes: 2.0x2.0x4.2 meters - Mass≈2000 kilograms - Power: 16 kW (supply voltage: 380V) Iisdpfjiy Dl Hsx Apneb - Average productivity: 1 pipe / 6 minutes - Loading of the machine with concrete: manual; (optional – by conveyor belt) - Manipulating the formwork with the concrete pipe inside: with the forklift; - Recovery of the formwork: immediately. - Recovery of the ring: after 2-3 days, depending on the ambient temperature. - The frequency converter allows adjustment of speed according to the inside diameter of the pipe. - Changing the rotating head is simple and fast. - Rotating heads are lined with interchangeable wear resistant steel sheets. EQUIPMENT REQUIRED: - MX500L Concrete Mixer with aggregate loader: concrete preparation - Conveyor: transport of concrete from the mixer to the formwork. Steel rings for the lower plug - The production surface must be perfectly flat!

Condition: good (used), Year of construction: 2013, L-shaped platform with staircase, handrail and transfer station, stainless steel – used – : Price ex location: only €2,500 (net), dismantled, packed and loaded! Manufacturer: unknown Type: unknown Year of manufacture: 2013 Iodpswxv Dcsfx Apnsib Stair width: approx. 70 cm Step width: 60 cm, step depth: approx. 17 cm Platform height: approx. 1.16 m Platform dimensions: Depth of narrow side: approx. 87 cm – plus staircase Staircase depth: approx. 1.18 m Total depth incl. staircase: approx. 2.05 m Width: approx. 2.28 m Width at staircase location: approx. 77 cm 1 staircase Handrail on 3 sides, handrail height approx. 1.10 m Incl. folding opening / transfer station Opening width: approx. 1.27 m Condition: good Available: immediately Location: Warehouse Frankenberg (Saxony)

Year of construction: 2013, condition: good (used), Crossover / Platform / Staircase, Günzburger – used – Ex-works price: only €1,795 (net), dismantled, packed and loaded! Manufacturer: Günzburger Steigtechnik GmbH Type: unknown Year of manufacture: 2013 Permissible load: 200 kg Platform / crossover height: approx. 1.25 m Platform dimensions: approx. L: 80 cm, W: 80 cm step width Total width: approx. 86 cm Steps: width approx. 80 cm Railing height: approx. 1.12 m Total height (with railing): approx. 2.35 m 2 x 6 steps Railing on both sides Original price: over €3,000 (net) Condition: good Available: immediately Iisdpswxv Eysfx Apnob Location: Frankenberg warehouse

Condition: good (used), Year of construction: 2020, functionality: fully functional, type of input current: three-phase, 🔥 FOR SALE: Fiber Laser Welding Machine — XTW-1000 (2020) A professional-grade fiber laser welding machine, model XTW-1000, manufactured in June 2020, is for sale. The machine is in excellent working condition and ready for immediate use. This unit is perfectly suited for precision welding of stainless steel, carbon steel, aluminum, copper, galvanized sheet, and various metal alloys. Laser welding is 4–10 times faster than conventional TIG/MIG welding, produces clean and smooth welds with minimal heat distortion, and requires little to no post-processing work. 📋 TECHNICAL SPECIFICATIONS • Model: XTW-1000 • Laser type: Fiber laser • Output power: 1000 W • Laser wavelength: 1080 nm • Laser spot size: 1–2 mm • Rated power: 7500 W • Supply voltage: 220V / 50Hz • Current: 30 A • Laser safety class: Class 4 • Serial number: 202005145 • Manufacturing date: 2020-06-01 • Certification: CE ✅ APPLICATIONS • Sheet metal processing & manufacturing • Stainless steel product & kitchen equipment fabrication • Automotive repair & bodywork • Elevator & staircase manufacturing • Tool & hardware production • Custom metalwork & repair workshops Iiodeyzcg Nspfx Apnjb 📞 For further details and pricing — contact the seller!

Condition: good (used), Year of construction: 1999, functionality: fully functional, input voltage: 400 V, Used machine MAKA FPM 470R 5-axis CNC machining center for machining wood, plastic and aluminum. Machine in mobile portal design, with rack and pinion drive. The machine was last used in wooden staircase construction. Year of manufacture: 1999 // RETROFIT in 2019 Technical data: CNC control BWO Vector 921 for 5-axis machining. 256 MB NC memory, USB connection, mobile control panel. Working areas in 5-axis operation, with tool diameter 60 / length 160 mm: Y-axis: 5,600 mm X-axis: 1,600 mm Z-axis: approx. 380 mm / with 180 mm fixture height (OK vacuum suction cup) Working areas in 3-axis operation, with tool diameter 60 / length 160 mm: Y-axis: 6,000 mm X-axis: 1,600 mm Z-axis: approx. 380 mm / with 180 mm fixture height (vacuum suction cup) A-axis 540° (rotation axis), B-axis 196° (swivel axis +/- 98°) Rapid traverse speed: X-/Y-axis 45 m/min., Z-axis 15 m/min., A-/B-axis 10,000 °/min. Milling unit: - 1 universal unit for 5-axis milling with 50° inclined head, power max. 12.5 kW, speed continuously adjustable up to 17,000 rpm, milling spindle water-cooled. - 1 NC height-adjustable chip collection system with slat curtain. Tool magazine: - ISO 40 tool interface for automatic tool change system. - 2 chain tool magazines with 32 spaces each for tools up to D = 90 mm, with sorted storage up to max. 160 mm. (Three spaces are required for this). Machine table: - 10 support tubes on linear guides with pneumatic release device for quick positioning. - 2 control circuits for "lifting/lowering" stops - 2 control circuits for "clamping/loosening" pneumatics - 2 vacuum control circuits with button for clamping and automatic reset through CNC programming. - 2 step separators, stroke approx. 320 mm. - Various clamping devices for posts and curved parts. - 1 chip conveyor belt integrated in the base frame, for removing chips and small waste up to max. approx. 100 x 100 x 100 mm. Tools: Tools are not included in delivery! Vacuum supply: - 1 vacuum pump, including tank with 250 liter capacity for quick vacuum build-up. - approx. 20 vacuum supports with various suction cups. - 4 lifting/lowering stops for positioning components. Other: - Automatic central lubrication. - Control cabinet with air conditioning unit. - Projection laser Work safety: - Traveling protective cabin with safety bumpers. Overhaul / repairs in 2018 / 2019: - Conversion of the rotary and swivel axis to a new generation of drives (digital). - New Y- / X- / Z-axis energy chains. - Complete new cabling, all power and measuring system cables renewed. - All guide carriages new - New Z-axis ball screw and guide rails. - New X-axis guide rail. Iiodsvmpx Repfx Apnjb - Control system converted to BWO Vector 921, with V-CNC card 256 MB NC memory. - New vacuum valves and vacuum hoses. - 2 x tool magazine + tool gripper overhauled. - Swivel suction overhauled. Software: - It is possible to take over a current version of the Compass staircase construction software. Compass is the leading provider when it comes to the planning and production of wooden staircases.

Condition: excellent (used), Year of construction: 1986, operating hours: 60,000 h, functionality: fully functional, This offering comprises a complete production line for manufacturing Rubber and EVA foam. The line features machinery by leading manufacturers, including German brands such as Fecken Kirfel, Boge, and Wesero; Italian companies such as Moderne Meccaniche, Mapelli, Terenzio, Vigevano, and FGB; as well as Taiwanese manufacturer Kim Ho Sheng, among others. Iedoyrbybopfx Apnsib The production line consists of several large industrial machines, each equipped with operator platforms, intuitive control panels, heavy-duty metal rollers, and exhaust hoods. Most machines have a green finish and are fitted with prominent blue motors. Elevated sections are accessible via staircases, and control panels and electrical cabinets are mounted conveniently on the right side of certain units for streamlined operation. Production line components include: - 1 Italian 40-liter Banbury mixer (Moderne Meccaniche) - 1 Italian open mixing mill (Moderne Meccaniche) - 4 Taiwanese open mixing mills (Kim Ho Sheng Industrial Co., Ltd.) - 1 Greek-built conveyor belt with integrated automatic cutting system - 1 large Italian vulcanization press (Terenzio, 6 plates) - 2 medium-sized Taiwanese vulcanization presses (DAH TYAN HYDRAULIC MACHINE INDUSTRIAL CO., LTD, 6 plates each) - 1 small Greek vulcanization press (MIEL, 2 plates) - 1 German rubber buffing machine (Wesero) - 4 German bandknife horizontal splitting machines (Fecken Kirfel: 2 x K11, 2 x G1) - 1 Greek strip cutting machine - 1 Greek granulator (MIEL) - 1 Italian thermoforming machine (Vigevano) - 2 Italian semi-automatic travelling head cutting presses (MAV-2, Vigevano) - Approximately 100 iron chrome-plated moulds suitable for rubber and EVA foam - 1 German industrial screw compressor (Boge C30) with a 1,000-liter tank and Omega dryer - 1 Greek oil steam boiler, 800 kg capacity (PROODOS) - 1 Italian burner (Riello RL70) - 1 Greek-manufactured industrial chiller, 174 kW capacity - 1 German industrial air heater (Wolf) - 1 heating chamber - 1 French PVC mixer (Lancelin) - 1 Greek floor-standing electronic weighing scale, 1,500 kg capacity (LION ENGINEERING) - 1 German industrial aluminium scaffolding (Krause, 6 meters) - 4 Italian trimming machines (FGB) - 10 assorted scales This comprehensive production line offers a turnkey solution for rubber and EVA foam processing.

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, working width: 450 mm, warranty duration: 12 months, total height: 220 mm, total width: 460 mm, total length: 880 mm, water tank capacity: 10 l, We offer for sale a BR 45/10 Esc Staircase Scrubber Condition – Very good Year of manufacture – 2014 The machine is in very good condition – both visually and technically. It has undergone a complete, thorough overhaul, making it fully functional and ready for operation. Each device we offer is presented in authentic photos – you are buying exactly the machine shown in the pictures. Iodpfxow Igrzj Apnjib All machines purchased from us come with a 12-month WARRANTY. Technical Data: Brush working width (mm): 450 Working/suction width (mm): 450 Tank capacity (l): 10 Brush rotation speed (rpm): 290 Brush motor power (W): 190 Vacuum motor power (W): 1500 Voltage (V): 220 / 240 Frequency (Hz): 50 Weight (kg): 44 Dimensions (L x W x H) (mm): 880 x 460 x 220