Bale press

Paal Comdec 60 PFT

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h Gsdpjvf E Avofx Anljuc bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), DIXI 60SLD is a semi-automatic baling system with a pressing force of 60 tons, designed for economical volume reduction of recyclable residues in industrial and craft sectors: - Cardboard boxes - Foams Guedpfxera A E Uo Anlec - PET bottles - Insulation mats - and other pressable materials Horizontal baler, DIXI 60 SLD waste press with tipping device Technical specifications: Pressing force: 60 tons Specific pressure: 6.81 kg/cm² Power supply: 400V / 7.5kW Bale dimensions: 800 x 1100 x 1200 mm Number of ties: 3 Bale weight: approx. 370–410 kg Tying: manual Feed opening: 990 x 1110 mm Machine weight: 5,420 kg Average pressing cycle: 47 sec Year of manufacture: 2011–2016 Dixi 80SLD Baler Technical Data of the Baler Brand: Dixi Model: 80 SLD Pressing force: 80 tons Drive power: 11 kW, 400 V / 32 A Feed opening (W x H): 1040 x 1110 mm Pressing cycle: approx. 35 sec Throughput: approx. 1,000 kg/h Bale size (W x H x L): 1120 x 1120 x 1200 mm Bale weight: depending on material, approx. 500–600 kg Bale tying: triple, manual Machine dimensions: Length: 4,200 mm (+cage 1,600 mm) Width: 1,830 mm Height: 2,620 mm Machine weight: approx. 8,000 kg Automatic bale ejection Robust construction for long-term use Year of manufacture: 2016–2020 Weight: approx. 8.4 tons Condition: Used

Condition: ready for operation (used), Number of blades: 6, rotor diameter: 350mm, engine power: 50kW, with construction as steel/welded construction in reinforced design and documentation, an inspection is possible, year of construction unknown, was overhauled in 2022. Gusdpfx Anen Tpmusloc

Condition: used, Year of construction: 2014, operating hours: 18,700 h, overall weight: 27,000 kg, number of blades: 41, rotor length: 1,800 mm, power: 200 kW (271.92 HP), rotational speed (max.): 87 rpm, input voltage: 400 V, Slow-speed, robust single-shaft shredder suitable for the pre-shredding of various materials without heavy contaminants. Applications: Shredding of industrial and commercial waste, films, packaging materials, textiles, paper, rubber, demolition wood, pallets, paper rolls, cable drums, and mixed plastics for thermal recovery or material recycling, whether loose or baled. Lindner Jupiter 1800 Drive power: 1x 200 kW (ABB) Screens: SK 80 mm Control cabinet: complete with (ABB frequency inverter) Recooling unit: Yes, included Feed opening: 1790 x 1750 mm Filling volume: approx. 4 m³ Rotor length: 1770 mm Rotor diameter: 745 mm Rotor speed: 50Hz : 87 rpm Gjdpfxow Tk Ude Anlsuc Number of rotor knives: 41 pcs Knife dimensions, pointed knives: 87x87x38 mm Counter knives, lower: 5 pcs Scraper comb, upper: 5 pcs Hydraulic feed: 11 kW Weight: approx. 27 t Dimensions LxWxH mm: 4800 x 3260 x 3090 mm Hopper: included Delivery time: immediate

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Drive power: 31.5 kW Pressing force: 60 t Bale weight (depending on material): 350–600 kg Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Gusdpfx Anjv Amw Nsloc Pressing/cycle time: 13/24 s Machine weight: 7000 kg

Condition: good (used), Year of construction: 2014, operating hours: 18,520 h, Single-shaft shredder, especially suitable for secondary shredding and granulation of pre-shredded material. Application: Commercial waste for thermal or material recovery, e.g. paper, cardboard, plastics and foams, rubber, leather, textiles, floor coverings, etc. Lindner Power Komet 1800 Year of manufacture: 2014 Control cabinet; complete with ABB frequency converter, Recooler Operator panel Hopper Drive motors: 200 kW Hydraulic unit: complete Total weight approx. 21 t Gsdpjwxmb Eefx Anlsuc Dimensions approx. LxWxH mm: 5000 x 2800 x 3000 mm Inspection: possible upon arrangement. Delivery time: immediate.

Condition: excellent (used), Year of construction: 2014, operating hours: 8,900 h, machine/vehicle number: LP50VH2, 1) Technical specifications Press with conveyor Technical data baler: Gjdpfxsyrhi Ne Anlsuc Manufacturer Presona Typ LP 50 VH2 Year of construction 2014 Press power main press 50 tons Specific press force 63 N/cm2 Feed channel 1,500 x 1,100 mm Filling volume 2,7 m3 Theoretic throughput capacity 730 m3/hour Throughput capacity under operating conditions 340 m3/hour Bale size 1,100 x 720 mm, lenght variable Drive power 45 kW Tying system 5-fold, vertical, fully automatic Throughput capacity at a • bulk weight of 30 kg/cbm 8 up to 10 tons/hour • bulk weight of 50 kg/cbm 11 up to 13 tons/hour • bulk weight of 100 kg/cbm 15 up to 22 tons/hour Bale density (paper, newspaper) 400 up to 550 kg/m3 Filling volume hydraulic oil tank 600 l Weight baler 16 tons netto Scope of delivery: Press, electrical cabinet, control panel, chain conveyor The documentation (operating manual, CE declaration, electrical/hydraulic diagram) is complete. Visiting is possible by appointment. We are not responsible for technical information or any errors. Upon request, we can send video materials of the working press

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Guedjv T I Evepfx Anloc Total operating hours: 37,565 hours, as of March 2025 Main press force: 85 t Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying system: 5-fold vertical Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Your service team at Mertens & Frowein GmbH

Condition: used, Year of construction: 2024, color: green, empty load weight: 4 kg, first registration: 06/2024, fuel type: gasoline, gearing type: mechanical, TITLE: USED OPEN-TOP HOOK-UP CONTAINER FOR BULKY WARE IN HARDOX, REAR OPENING WITH TWO FOLDING DOORS + MEC CRANE WITH PANTOGRAPH FEET AND 6-BLADE GRAPPLE WITH MECHANICAL ROTOR REF: 24-U-103 TYPE: bulky goods with crane NEW: no LID: no OPENING: rear with two folding doors OVERALL DIMENSIONS Gjdpfxsv Hicio Anljuc TOTAL EXTERNAL LENGTH: 5.90 m CASE LENGTH: 4.70 m + 1.00 m crane space + 0.20 m beams CASE EXTERNAL WIDTH: 2.50 m CASE INTERNAL / EXTERNAL HEIGHT: 2.30 m / 2.50 mt MC: 25 WEIGHT: 6020 kg BOTTOM: 5 mm WALL: 4 mm COLOUR: green CRANE DATA BRAND: MEC F1211.S2 SERIAL NUMBER: 50579088 EXTRACTIONS: 2The prices shown do not include VAT. Please contact the sales representative for an updated comparison of prices and conditions. For more information: Loris: 3484773001 URL: #glispecialistidelloscarrabile SCARRABILI AURORA operates in the sector of the sale and purchase of industrial and commercial vehicles, mainly specialised in the waste sector. Specialised in trucks, trailers and hook-lift equipment. With a fleet of over 50 trucks and over 150 skip loaders, containers with and without hook-lift cranes ready for delivery. S.E.&O Given the quantity of ads and details entered, Aurora invites you to verify the accuracy of the data entered with the sales staff.

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Gujdpfxetvat Tj Anloc After refurbishment, this baler is sold with a 2-year warranty.