Paint shop

Pony Luxury Coating M&K Pony 7000

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Bljdpfx Adewzmcbehjp Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Condition: new, Year of construction: 2025, Oven for the powder paint shop powered by natural gas. The furnace is designed for the polymerization of powder paint. It is equipped with the latest heat exchanger made entirely of stainless steel AISI 1.4301, characterized by very high efficiency. Working dimensions (mm): 1500 (W) x 9000 (D) x 2200 (H) Technical data: • Power supply 400V 50Hz • 2 x Riello 90kW burners • Operating temperature 210C • Maximum temperature 230C •High-class thermal insulation 150mm •Baffle in the middle of the stove allowing 50/50 Equipment: • upper transport, • Hot air circulation (Equal temperature throughout the furnace, acceleration of the heating process of details), • Safe opening and closing locks, • timer module, • Thermoregulator (controls the temperature inside and maintains it at the right level), • The stove is equipped with rails for easy transport. Cbauevig73 Bledsfktipepfx Adhep pvxg CHOOSE BUMEX SP. Z O.O. Very high quality of machines offered on the market. Professional advice and service. Guarantee. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our customers. All BUMEX SP. Z O.O. are WE certified. We offer our own transport - prices are set each time for a given offer. We issue VAT invoices. Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Feel free to contact us.

Condition: new, Year of construction: 2026, functionality: fully functional, warranty duration: 12 months, workpiece weight (max.): 100 kg, power: 88 kW (119.65 HP), temperature: 220 °C, heating capacity: 30 kW (40.79 HP), workpiece height (max.): 1,500 mm, workpiece length (max.): 500 mm, insulation material: Steinwolle, insulation thickness: 150 mm, workpiece width (max.): 500 mm, Semi-automatic powder coating system | Batch system with chemical pre-treatment & curing oven Compact, semi-/partially automatic batch powder coating system for steel components (1,500 x 500 x 500 [mm]). Complete system including 2-chamber spray tunnel (degreasing/phosphating/rinsing), flash-off oven, mobile powder spray booth, curing oven (max. 220°C), cardan chain conveyor, and PLC control. New system / project proposal – special dimensions, heating types, layouts, etc. can be individually adapted to customer requirements. System concept & customer-specific customization: Semi-automatic powder coating system in batch mode for the efficient coating of steel parts. The system combines a compact footprint with high throughput and is ideal for small to medium-sized series components. The pre-treatment process is automated in batch mode, and the coating is applied manually. Note on design: The dimensions, assemblies, and heating types listed below correspond to the indicative offer presented. All components (e.g., useful lengths, booth dimensions, chain path, gas instead of electric heating) can be fully customized to your specific component dimensions, space requirements, and process requirements. - Max. component dimensions (standard indicative offer): 1,500 x 500 x 500 [mm] (variable) - Max. load capacity per carrier: 100 kg per batch (higher load capacities on request) - Space requirement / footprint: approx. 12,000 x 6,500 [mm] (layout can be flexibly adapted) - Total connected load: approx. 88 kW (max.) - Batch cycle time / feed rate: Batch dwell time approx. 8.5 - 12 min at a chain speed of 3.2 m/min Technical data (overview of indicative project) System type: Semi-automatic batch system Max. workpiece size: 1,500 x 500 x 500 [mm] (individually scalable) Load capacity / carrier: 100 kg (higher loads can be designed) Oven temperature: max. 220/250°C; operating temperature 180-200°C Heating for dryer/oven: Gas, oil, or electric (indirect) Max. power consumption: 88 kW (depending on system size) Control: PLC (e.g. Siemens) System components overview: Chemical pre-treatment (3-zone spray cleaning): Compact 2-chamber spray tunnel made of stainless steel for degreasing/phosphating (or alternatively nanoceramic) (40 - 45°C) as well as 2-stage rinsing. Complete with stainless steel pumps, PPR nozzle bars, and extraction (4,000 m³/h). Flash-off oven & powder curing oven: Two thermally insulated chambers (100 - 150 mm rock wool) with indirect electric heating (thermoblock with 16 or 30 kW), stainless steel combustion chambers, and powerful air circulation. Dryer up to 120°C, oven up to max. 220/250°C (automatic lift-up doors optional) Mobile powder spray booth: Mobile, open coating booth (2,000 x 2,100 x 2,200 [mm] with ATEX extraction (6,000 m³/h). Integrated filter unit with 4 pulse valves for cleaning, absolute after-filter, and mobile 60 l powder container. Note: Fully enclosed powder booths are also available! Conveying technology & control: Driven cardan chain conveyor with frequency inverter and automatic lubrication unit. Bljdpjulwg Nefx Adhop Control via PLC for complete control and adjustment of all system processes (control cabinet equipped with Siemens/Schneider) Scope of supply: Complete system including customer-specific design, assembly, and on-site training.

Condition: used, Year of construction: 2006, functionality: fully functional, machine/vehicle number: GG60SB-13594, total width: 4,030 mm, total length: 7,000 mm, overall weight: 2,500 kg, input current: 11 A, type of input current: three-phase, input voltage: 400 V, input frequency: 50 Hz, feed length X-axis: 3,300 mm, feed length Y-axis: 6,100 mm, pressure: 8 bar, cutting length (max.): 6,100 mm, Bottero float cutting table (shapes) 2-19mm, max cutting size L6100x3300mm Dimensions: L7000xW4030mm, weight +/-2500Kg Blsdpfexrmpmex Adhop

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, Paint/spray booth dimensions without fan and control Panel! Extraction surface - dimensions (mm): 3000(w)x1900(h) Overall dimension(mm): 3100(w)x2350(h)x1910(d) Technical data: - Fan power 3kW (ATEX) - Fan suction capacity: 16000 m³/h (max 1100Pa) Bljdpfxjia Taus Adhsp - Lighting: 2 pcs 2x36W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: ready for operation (used), Anti-spark centrifugal extractor fan Cardboard filters “Paint-Stop” filter Electric panel with IP55 protection class Ceiling light with IP65 protection class Emergency push-button Discharge hopper Blodpfxow Rpxcs Adhsp

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. Bedofz Dubopfx Adholp This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Condition: used, System D8 brand painting chain, 94.50 linear meters, complete with towing, tracks and chain. Bledpfsm D Hcfjx Adhsp

Condition: good (used), Year of construction: 2005, Complete industrial paint booth, manufacturer Walther: 1 single booth + 1 double booth. Drawings with dimensions are available upon request. Bedsxvbdmspfx Adholp

Condition: new, Year of construction: 2027, HORIZONTAL POWDER COATING LINE FOR ALUMINUM PROFILES We are adding value to your production. * Conveyor speed up to your capacity per day Aerial conveyor - monorail or power&free type Bedpfx Adovv Nh Rehjlp Automatized powder coating booth, metal or PVC antistatic structure Reciprocated automatic powder coating equipment system Tunnel type polymerization oven - gas, diesel or electrical heating source Made in Türkiye CE Mark We offer the best technical solutions and competitive prices * Office in France and Germany, Contact us for more information and quotations