Labelling machine

Wilux DLS 2100 / WLS-1206-LH-PA-90°

Condition: excellent (used), machine/vehicle number: 3.278-870805-1, Part No.: 42.35.53 Dodpfx Apeh Eii Tsbecn Technical data and description: see pictures

Condition: used, Year of construction: 2022, Maximum parent roll width: 1420 mm Minimum parent roll width: 600 mm Maximum parent roll diameter: 1500 mm Maximum parent roll weight: 2500 kg Maximum unwinding tension (Ø1500 mm): 600 N Minimum unwinding tension (Ø1000 mm): 40 N Minimum standard slitting width: 100 mm Maximum rewinding width: 1400 mm Maximum rewinding diameter: 1050 mm Maximum rewinding weight: • Ø76 mm shaft: 600 kg • Ø152 mm shaft: 1000 kg Maximum rewinding tension: 600 N Maximum production speed: 600 m/min Power supply: 3 x 400V 50Hz Installed power: 30 kW Compressed air: 6 bar, dry Materials to be slit: • Paper-based / liner-based packaging laminates. • Board from 80 to 300 g/m². Unwind section: A separate between-centers unwinder, type T9, 1500 mm diameter, including: • Hydraulic cylinder control for lifting parent rolls from the floor. • Two motors driving the unwinding roll, controlled by an ultrasonic diameter sensor and a tension-control dancer roller. • Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3”) cores. • Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6”) cores (mounted on the pneumatic end adapters). • Floating edge-correction roller. • Automatic web guiding system, FIFE DP20, with SE26A photoelectric sensor, ±100 mm correction via electric actuator — for controlling sheet edge or continuous printed line. • Connecting walkway allowing web threading at floor level while keeping full access to the slitting station. • All web path rollers are anodized. • Safety guarding for operator protection. Slitting section: A slitting station with individual pneumatic knives and circular counter-knives: • Shear cut performed against the counter-knives. • Counter-knife shaft driven by an independent motor; counter-knife shaft is pneumatic. • Pneumatic knife holders mounted on a beam with a dovetail guide (TIDLAND) and an air supply manifold for individual activation. • 10 slitting sets, each including: Individual TIDLAND pneumatic knife holder (25 mm width) and double-bevel circular knife Ø 90/60 mm. • Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm length. Web separation section: • A separator roller driven by the slitting motor; angle and curvature fully adjustable. Lay-on roller: • Lay-on roller made of anodized ground aluminum or polyurethane (depending on materials). • Pressure is adjustable and synchronized with winding diameter. • Roller is removable. Automatic splicing / transverse cutting system: • Hydraulically operated pivoting arm including a transverse knife with linear motion and a backing plate for securing the web onto new cores. Trim extraction system: • Trim suction unit with two width-adjustable nozzles. Dedpeyx Uy Aefx Apbocn • Turbine enclosed in a sound-insulated cabinet, conveying trim to a centralized system or container (not included). Rewinding section: • Motorized turret (two-position) supporting two rewinding shafts. • Rewinding shaft drive by an oversized asynchronous motor. • Hydraulic centering point for the active rewinding roll. • Two pneumatic expanding shafts Ø76 mm (3”), max load 600 kg each, equipped with full-width rubber strips with individual bladders. • Two pneumatic expanding shafts Ø152 mm (6”), max load 1000 kg each, also equipped with full-width rubber strips with individual bladders.

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: 259747, Size 516mm, roll-to-roll digital printing machine for labels, etc., Xeikon X800 front end mypress: incl. barcode and trapping software, Hunkeler unwinder, airshaft, ultrasonic webguide sensor, GEW UV dryer, 3 slitting knives, GM rewinder, Corona Plus. Dcsdoy Rywwopfx Apbjn

Condition: excellent (used), Year of construction: 2006, Single-screw extruder Battenfeld BEX 1-75-30:B with co-extruder BEX 35-30:B Application for PE, PP Year of manufacture 2006 Screw RPM 220 Screw diameter 75 mm Drive Baumüller 205 KW, RPM 2.450 Total output approx. 850 kg/h The extruder was converted to frequency drive by Battenfeld in 2014, new three-phase motor and frequency converter Gearbox was overhauled in July 2024 Condition: it is in very good condition Last application PE pipes Battenfeld co-extruder BEX 1-35-30:B Application PE PIPES Screws RPM 240 Connection value: 69 Kva Drive 35 KW Output approx. 120 kg/h Year of manufacture: 2010 Dsdpfx Apjug Edksbecn The extruder is my property Location: D-26345 Bockhorn-Grabstede, Bahnhofstr 6 Germany

Condition: used, Year of construction: 2006, working width: 520 mm, roll width: 520 mm, roll diameter: 1,000 mm, Equipment: documentation/manual, Video below We offer this used ETI Converting Equipment Cohesio ST 520 coater, die cutter, UV silicone coating, flexographic printing press 1 colour, , 11 magnetic cilinders, year of construction 2006. multifunctional equipment that allows self-adhesive materials and labels. linerless 1 flexo 2 hotmelt coating guns (roatating bar, lips + ‘Waterwall”) 3 unwinders Web width of 520 mm Dedpjyalqyefx Apbecn E + L webguides at the infeed and between hotmelt and UV printing unit 2 Corona treatments for two unwiders 2 cleaners UV Curing on 1 Flexo units (UV-Ray), which chilling rolls 2 die cutting units Chiller Working hours 9000 Year of production 2006 more information on request If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: used, Tool grinding machine, twist drill grinding machine BORA -- BI-EMME s.n.c. (Italy) Type 1/BM 40 No. 49697 Year of manufacture 1997 Grinding range Ø 3 - 40 mm Center angle 40° - 180 Motor power 1.1 kW Grinding wheel dimension max. Ø 200 mm Grinding wheel speed 2840 rpm Mains connection 400 Volt, 50 Hz - For grinding standard drills and other tools with 1, 2, 3, 4 or 6 cutting edges (step drills, taps, countersinks, drills with a thick core and drills with special grinding) - Precision six-jaw chuck Ø 125 m - pointing device (motor power 0.18 kW) - For left and right cutting drilling tools thanks to interchangeable cams - Cam disks easily interchangeable for 2 or multi-bladed tools - 4 cam disks - Centering arbor for MK1, MK2, MK3, MK4 - A white grinding wheel with a diameter of 170 mm and a width of 40 mm is installed - Metal base with door and shelf Dodpfxjnzt A Hj Apbecn - Wet grinding unit shown opposite - Operating instructions per PDF Space requirement L x W x H 900 x 850 x 1250 mm Weight 220 kg Very good condition

Condition: used, Year of construction: 2022, PRODUCT TYPES: • Four side seal pouches • Quad seal pouches • Side seal pouches • Transverse zipper pouches • Gusset pouches • Bottom stick hole pouches • Micro-perforated pouches • Handle hole pouches • Round corner pouches MATERIALS: • LDPE • CPP • MCPP • AL • Nylon • PP • Laminated film structures MAIN TECHNICAL INFORMATION: Material thickness: 60–250 μm Max. web width: 1300 mm Dcjdpozf Nk Tofx Apben Max. roll diameter: 800 mm Core diameter: 3” and 6” Max. pouch width, quad seal: 400 mm Max. pouch length: 1000 mm Eye mark accuracy: ±1 mm Machine speed: 15–65 pcs/min Material speed: 40 m/min Main power: 400V, 50Hz, 3 phase Installed power: 100 kW Machine weight: approx. 18,000 kg Machine size: 33,500 × 4,200 × 1,800 mm POUCH SIZE RANGE: Quad seal / side welded width: 180–400 mm Gusset depth: max. 80 mm Minimum gusset depth: 30 mm Bag length: 360–1000 mm UNWINDING SECTION: • Air shaft unwinding • Magnetic powder brake • Dancing roller tension control • Servo-driven unwind system PERFORATION SYSTEM: • Micro perforation unit • Wheel type perforation • Additional perforation holes • Same type as existing machine configuration FOLDING SYSTEM: • Four side seal / quad bag folding wheel section SEALING AND COOLING SYSTEM: Mechanical press sealing system: Quad seal longitudinal sealing: 2 groups, 1010 mm Quad seal longitudinal cooling: 2 groups, 1010 mm Cross sealing station: 6 sets No. 1: K-seal No. 2: Gusset filling sealing No. 3: Cross seal, 740 mm length / 60 mm width No. 4: Cross seal, 740 mm length / 60 mm width No. 5: Cross seal, 740 mm length / 60 mm width No. 6: Cross cooling, 740 mm length / 60 mm width Additional 5 mm sealing section, upper and bottom PUNCHING SYSTEM: Tear slit / notch puncher 3-hole handle puncher Handle puncher: 20 × 80 mm, 3 sets Hole sizes: • 3 holes Ø20 mm • 20 × 80 mm • 24 × 77 mm Round corner puncher: 2 sets Puncher supports: 3 sets Bottom stick hole puncher: • 12 mm, 8 pcs • 16 mm, 8 pcs Vacuum system for punch waste removal DRIVE SYSTEM: Main motor: 3.5 kW Back draw roller servo: 3.5 kW Front draw roller servo: 3.5 kW Middle draw roller servo: 3.5 kW Longitudinal independent sealing servo: 5 kW × 2 Unwind servo motor: 1.5 kW × 1 / 3.5 kW × 1 Tension control servo: 3.5 kW × 1 Flying knife servo: 1.5 kW × 1 Manipulator sucker drive: 0.75 kW × 1 Finished product carrier counting drive: 0.75 kW × 1 CONTROL SYSTEM: • PLC control • 10” touch screen • Suitable for printed and unprinted bags • 16 temperature control zones • Individual temperature display • Temperature tolerance: ±2°C • High-sensitive eye mark sensor • Adjustable eye mark position STACKING SYSTEM: • Simple type stacking table • Static removal system • Automatic stop when machine stops • Alarm for bag output range: 25–100 bags • Step motor belt control • Belt width: 60 mm • Adjustable batch and belt length SAFETY SYSTEM: • Safety light curtain • Emergency pulling rope • Emergency buttons every 2 meters • Individual emergency control INCLUDED OPTION: ZIPPAK transversal zipper attachment Transversal zipper unwinder and rewinder Innolock / Velcro zipper capability Tooling for 3 zipper sizes: • 180–220 mm • 230–300 mm • 310 mm Micro-perforation holes Bottom stick hole puncher Trim rewinders Chiller

Condition: used, Year of construction: 2011, Web Width: 850 mm 1. Unwinding and Infeed System - Unwinder with constant web tension control - Web guiding and stabilization unit - Electronically controlled infeed system with precise tension regulation - Complete drive package for accurate web handling 2. Rewinding System - Single-shaft rewinder, max. roll diameter: 1000 mm - Constant tension control for stable winding 3. Surface Treatment & Web Cleaning - Corona treatment unit for surface energy optimization (pre-print) - ACE single-sided contact roller web cleaner for dust and particle removal 4. Printing Units Flexographic Printing Section - 8 flexo printing units with: - Central impression drum - Removable ink drawer (excl. anilox rollers) - Optional flexo features: - Explosion-proof configuration (per print station) - Drum cooling system - Lightweight anilox rollers: - 5 units (195–300 lpi) with gear - 5 units (>300 lpi) with gear - 24 print sleeves with cams - 2 additional ink drawers (tray + rubber roller) - 1 trolley for ink drawers (3 slots: 2 in use + 1 reserve) Special Flexo Units Dcjdpfx Apoy Ey Niebjn - 1 cold foil trolley - 1 movable cold foil unit (can be positioned at any print station, rail-free design) Rotogravure Printing Section - 1 rotogravure station for front- or reverse-side printing, includes: - Reversing bar for reverse-side printing - Designed for PETROCOLL cold-seal coating (2.8–3.2 g/m² at 180 m/min on paper) - Rotogravure trolley for mobile positioning - Extended hot air drying system: - “Super Hood” with 32 high-efficiency blowers - Methane gas burner for heating - Integrated cooling unit - Electrostatic assist for ink transfer - 3 rotogravure print sizes (16”–26”) - Solvent ink viscometer - Pump and ink supply tank 5. Drying and UV Curing - 8 UV curing units, 22 kW each (one per print station) - Integrated cooling for UV lamps - Drum cooling for heat-sensitive substrates 6. Die-Cutting and Finishing Units - Rotary die-cutter, working width up to 530 mm - Base unit for die station - Trim removal system (up to 530 mm wide) - Matrix waste pressure system (limit: 530 mm) 7. Slitting Section - Shear (scissor) slitting system - 6 Helios box knives with self-sharpening counter blades 8. Electronic Control & Inspection - OMET electronic register control for 8-color operation - Includes “gate” function for accurate registration - Vision system for real-time print inspection - Motorized E+L Elscan camera for high-resolution web monitoring 9. Safety and Compliance - Complete CE-compliant safety guards and emergency stop systems - Designed for ergonomic operation and rapid job changeovers

Condition: good (used), Year of construction: 2018, Xeikon CX500 Digital Label Press – (Roll-to-roll digital dry-toner press) Year of Manufacture: 2018 Print Media Handling • Roll-to-roll configuration with variable repeat length • Print width: 508 mm • Print speed: 20 m/min (65.6 ft/min), depending on substrate grammage • Media weight: 40 – 350 gsm (27 lb text to 130 lb cover) Print Engine • 5-color dry toner technology • Resolution: 1200 dpi • Color configuration: Dcjdjx Hh A Hopfx Apbjn o CMYK o Single-pass opaque white o Gamut extension o Custom spot colors _____ GM DC5V8-BX Converting & Finishing System Year of Manufacture: 2011 Web Specifications • Web width: 200 – 520 mm • Substrate thickness: 20 – 200 microns • Machine speed (semi-rotary): up to 55 m/min Main Units & Features • Unwind unit (max. diameter: 700 mm) • BST web guide with splice table • Servo-controlled flexo printing unit • UV curing unit • Laminating unit • Vetaphone corona treater • Die-cutting unit o Plate size: 50.8 mm – 520.7 mm o Magnetic cylinder: Z200 • Waste rewinder (diameter: 500 mm) • Slitting unit • Two rewind stations • Pre-installed buffer system for Xeikon digital press • Touch-screen operator control panel _____ SYSTEM BENEFITS When combined, the Xeikon digital press and GM DC5V8-BX finishing line form a complete end-to-end label production workflow, enabling: • High-quality digital printing • Inline or nearline converting • Flexo varnish, lamination, die-cutting, slitting, rewinding • Fast job changeovers • Efficient production of short, medium, and long runs Ideal for label converters seeking a compact, flexible, and fully integrated solution. _____ CONDITION OF THE MACHINES • Both machines are in good used condition • Fully operational prior to decommissioning • Offered as part of a combined setup for optimal productivity _____

Condition: ready for operation (used), A 4-color central cylinder printing system WDB Systemtechnik is available. Printing units: 4, ink type: UV, max. material width: 650mm, max. printing width: 600mm, printing length range: 300mm–800mm, max. printing speed: 250m/min, material types: PET/OPP/aluminum/laminate/composite materials, material thickness range: 20µm–150µm, max. unwind and rewind roll diameter: 1000mm, operating hours: 28h, printed length: approx. 57000m. System components: unwind and rewind unit, corona, UV dryer, drying channel, IR heater, cooling unit, and supply and exhaust air fan. Including lamination unit. Documentation available. An on-site inspection is possible. Dcjdpexmkctjfx Apbon