Faceplate 2013/13

700 mm KKG 8

Condition: new, Year of construction: 2024, Electro hydraulic press 110 Ton Made in Italy The P110 MR is equipped with: 400 V 50-60 Hz immersed motor control unit. Pump for fast approach and return in 20 bar calibration. Adjustable pressure pump with handwheel to obtain the required power. Pressure relief valve with mechanical block to prevent overpressure. Pressure gauge (standard) that allows to calibrate with extreme precision the delivered power. The P110 MR is the only hydraulic press consisting of 2 laser-cut FE 510 monolithic structure uprights. without welding in the places of greatest stress This feature gives it extraordinary robustness. It is non-deformable and guarantees tight working tolerances. The P110 MR is equipped with a 30-litre tank and has a rapid descent speed of 1,400 mm/min. Weight : kg 1,100 Max pressure : bar 350 Max. flow rate : t. 110 Rapid flow rate :l/min 34 Slow flow rate : l/min 5 Inside shoulders : mm 1004 Rapid rod feed : mm/min 1.400 Hsdpfsfh R N Djx Addsng Slow rod feed : mm/min : 130 Voltage : V 400 Frequency :Hz 50-60 Power : kW 3 Max. absorbed current : A 7,3 Cylinder stroke : mm 300 Cylinder diameter : mm 200 Stem diameter : mm 110 Piston descent speed : mm/sec 23 Tank capacity : litres 30

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 450x320 saw band length 4250x34x1,1 mm band speed 40 + 80 m/min table height 845 mm saw band width 34 mm total power requirement 2,2 kW weight of the machine ca. 0,985 t dimensions of the machine ca. 1,4 x 2,0 x 2,2 m Double miter band saw, hydraulic semi-automatic, DGS 350/450 HA-I · miter left + right 60° without machine conversion · 34 mm saw blade width · Large material support turntable, ball bearings · To position the saw blade guides using a very wide linear guide · Strong, robust transmission · Large chipboards · Infeed and outfeed roller Hjdofgyicepfx Addong Removable chip tray (disinfection) · Free-standing control panel, safe and ergonomic · Storage space for tapes, consumables · Cutting pressure regulator Feed regulator · Fully hydraulic vise Preload super fast (front loading) · Material height sensor (automatic cut start detection) Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise Optimum, material-independent cutting result through fine adjustment of the saw frame by means of: *Pressure Control Valve (Cutting Pressure Force) *Feed Control Valve (Speed) *Switch with pictogram, easy and clear to use

Condition: good (used), Year of construction: 2004, Comm. no.: Lg 34522 high performance punching press HAULICK+ROOS ROS 500 - 1250 used, in good condition year of construction 2004 (without sound insulation cabin) with Hnodpfx Ajip Uqmeddjg - infinitely variable drive - 2 connecting rods power unit - pneum. Clutch-brake combination - stroke adjustment - screen control Siemens PC 670 - oil circulation lubrication Technical data Pressing force max. 500 KN Stroke rate 30 to 900 min.-1 stroke 12 to 60 mm Installation height (max, stroke un U.T.) 320 mm column width 1.250 mm Table area 1.250 x 730 mm Drop-through opening in table 1,160 x 140 mm ram area 1.250 x 450 mm ram adjustment 60 mm Drive power 26 kW Weight approx. 11,000 kg Dimensions (L x W x H) approx. 2,800 x 1,300 x 3,250 mm Equipment and accessories: Servo roll feeder VAMCO SP 150 Year of manufacture 2014 Passage width max. 150 mm Material thickness max. 3.0 mm

Condition: new, 900 mm 900 mm 900x900 mm Hsdpsfg E Hpsfx Addeng saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Year of construction: 2020, condition: refurbished (used), Dear customers! Our experience has shown that the communication by e-mail usually drags out everything unnecessarily. We would like to help you quickly, but it is better to spend three minutes on the phone than three days writing e-mails back and forth. T.S.W.C. 30.20 Hnedpofn Nddefx Addog Dry bulkhead Dimensions: 3000 x 2000 mm W X H + Fan in the height Air capacity: 10.800 m³ / h Motor: 2,20 kW ex-proof Exhaust air pipe: 500 Ø mm depth: 900 mm Double filtration: paper filter + Paintstop filter mat over Terminal strip (+180,- EUR net) Options/additional price for: Paintstop filter mat terminal strip: 180,- EUR net side baffle plates with hinge: 590,- EUR net Pictures may vary. We can also offer you complete spraying rooms with supply air system, heat exchanger, supply air ceiling, piping etc. Just contact us.

Condition: used, 5tSWF Krantechnik GmbH Hedpfx Adjdc A R Todong

Condition: used, Year of construction: 1998, machine/vehicle number: 10870, Press capacity: 50 ton Ram stroke adjustable: 16 - 51 mm Slide adjustment: 64 mm Free frontal opening L-R: 1100 mm Free lateral opening F-B: 250 mm Table surface area : 1080 x 650 mm Slide area: 980 x 420 mm Hole in table: 1060 x 200 mm Number of strokes: 100 - 750 s.p.m. Required power: 22 kW Working hours machine: 16850 h Height over floor approx.: 2471 x 1278 x 3150 mm Weight of machine approx.: 9 ton Standard configuration Hodpfxsuqd Abe Addeng BRUDERER precision roller feed BBV 205 / 120

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, Initial commissioning: 2000 Control system: Heidenhain TNC 430 M Machine hours: 111,500 h X-axis: approx. 4,000 mm Y-axis: approx. 2,360 mm Z-axis: approx. 1,250 mm A-axis: ±110° C-axis: ±300° Clamping table Clamping surface: approx. 6,000 x 2,000 x 420 mm T-slot spacing: 18H12 / 250 mm Max. table load: 30,000 kg/m² 2-axis milling head AC3 Spindle power: 25 kW Spindle speed: max. 15,000 rpm Torque: 80 Nm Tool holder: HSK 63A Tool clamping: hydraulic Hodpfx Aow Rl S Seddeng Spindle freshly overhauled at the end of 2024! Linear axis drives Feed rate X, Y axis: up to 20 m/min Feed rate Z axis: up to 20 m/min Axis acceleration X, Y, Z: up to 1.5 m/s² Connection data Connected load: 40 kW Main fuse: approx. 80 A Dimensions & weights Machine footprint with peripherals: approx. 8,500 x 5,600 x 4,945 mm Total weight: approx. 18,000 kg Colour Enclosure, gantry, control cabinet: light grey Milling head and applications: green Additional equipment - 3-sided enclosure, without extraction ducts - The additional clamping table shown is not included in the scope of supply Condition of the machine Fully functional, in very good condition. Machine remains connected and is available immediately.

Condition: used, Clamping plate, marking-out plate, measuring plate, measuring table, welding table, welding table, straightening plate -Clamping plate comes: from a measuring machine -Width: 1335mm -Length: 3000mm -Height: 250mm -Plate thickness: 40 mm Hnodsfc T Tqepfx Addjg -Plate is with: support ribs -with: 4x adjustable feet -Number: 1 piece available -Transport dimensions: 3000/1335/H750 mm -Weight: 2749 kg

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m Hedpfod Iipmox Addong PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens