Year of construction: 1946, Condition: used, Vats - Installation of 4 concrete vats (building) including: - Agitators - Pumps - Valves - Piping - Installation of 1 concrete vat with: - Agitator - Pumps - WACO filter - Piping ----- Purification - 5 purifiers + KADANT BLACK CLAWSON Fibernet Duehxzv Eswbg Svsqjt - Tank - Sand removal screw - Conical stainless steel pulp chest - LAMORT purifier (partially dismantled, as is) ----- Supply - ALLIBE stainless steel vat - Pumps - Regulator - Control system ----- Starch water pumps - 2 MORET motor pump units - Stainless steel tank - Equipment for concrete vat (building) - Pumps - Piping ----- Paper Machine No.2 Brand: NEYRET-CORDEBART-THIRY – Year: 1946 Width: 2450 mm Hood and steam installation: BELLMER 1) Wet section - Natural drying: - 6 stainless steel suction boxes for paper dewatering - Mechanical drying: - 7 suction boxes with ceramic and plastic linings - Suction cylinder 2) Press section - Press No.1 with 2 cylinders (pneumatic tightening, LAMORT doctor blade) - Press No.2 with 2 cylinders (pneumatic tightening, LAMORT doctor blade) - Press No.3 with 2 cylinders (pneumatic tightening, LAMORT doctor blade) - Press No.4 "OFFSET Press" with 2 cylinders (hydraulic tightening) 3) Dryer section Installed in a large BELLMER suction cabin with automatic doors – humidity control system - Pre-dryer section: - 24 drying drums - 5 felt dryers - 23 doctor blades - Size press: - 2 cylinders - Pneumatic tightening - Reducer - 2 doctor blades - Post-dryer section: - 14 drying drums - Drying system: LANG (steam-based) 4) End of line - Rewinder with multiple cylinders - Sheet cutter: IBS RCS 5000 - Pneumatic equipment ----- MAP 2 Control Room - Digital control desks - Electronic installation - Paper monitoring scanner - Small furniture: coffee machine, top refrigerator, hot oven THERMOS SR1000 - Insect destroyer - Workbenches, vise, small rack ----- MAP 2 Sauce Kitchen - Remote-controlled sauce distribution network - Stainless steel storage - Agitator - Pumps - Valves - Filters ----- Sauce Preparation Kitchen (similar to MAP 1 and MAP 2) - 100T starch silo (old) with: - Valves - Dispenser - 2 pumps - Milk preparation tank - 2 dosing units for retention products (old) - Suspended milk cooker with digital control including: - Agitator - Pump - Double-jacket delumper - Steam extraction system - Tanks, pumps, mixers - Piping - Colorant installation ----- Vacuum Production Installation - 8 ALLIMAND vacuum pumps ----- Sauce Distribution Network

Condition: used, Year of construction: 1988, BOBST Printing Machine with 4 bottom colors anilox cilinders 120l/cm and 80l/cm TRANSFER BOBST FLATBED DIE CUTTER BOBST AUTOPLATINE SPO 1600, max format 1100 mm x 1600 mm / 43.3" x 63" with 4 Bottom Printing unit and transfer Bobst * Vacuum feeder * Die cutting section * Waste elimination section * Centerline II * High pile delivery with two lifting tables * Max sheet format: 1100 mm x 1600 mm / 43.3" x 63" * Min sheet format: 520mm x 600mm / 20.5" x 23.6" * Cutting force: 400 t * Materials: E, B, C, CB, BE flutes * Max speed: 6,000 sheets/hour Possibility to sell them separately Dohxjv Ifpuozv Eqjut

Condition: excellent (used), Iijima EFC-1600 die-cutting machine with break-out section and leading edge edging device for package delivery onto conveyor belt. Dshev Nzpgoxzv Eqeut

Year of construction: 2007, Condition: ready for operation (used), Functionality: fully functional, Wook il Machinery co ltd Automatic die cutter for corrugated boards Max. Sheet size 1100mm x 1500mm Min. Sheet size 550mm x 750mm Dujhxzjv R E Atev Eqet Max. Cutting Pressure 350 T Max. Cutting Speed 6000 S/H

Condition: excellent (used), Year of construction: 2001, working width: 2,800 mm, a) Martin Prefeeder b) Martin DRO 1628 GT Belt feeder introduction N. 4 colors from the bottom Vacuum transport between the groups Posilock die cutting tool lockind system Vacuum Stacker Ball rotary table c) N. 1 Bobst Breaker Ball rotary table Batch turner d) Martin palletizer Computer MPC2 Dohxswdvrdozv Eqjut Max size 1600x2800 mm.

Condition: good (used), Functionality: fully functional, machine/vehicle number: 30.61 472, Paper cutter. Cutting paper from rolls into sheets. Max sheet size: 1400 x 1600 mm. The machine has 8 paper roll unwinders. It is possible to cut several paper rolls at the same time. Djhxowfpifjzv Eqsut

Condition: used, Heidelberg platen press Dehjwbqilsxzv Eqout Size 34x46 Original manual included Ready for use

Condition: good (used), Year of construction: 2003, total width: 1,320 mm, Machine type: Roll-to-roll laminating machine for solvent-free adhesives, 1K or 2K. Manufacturer: NORDMECCANICA Type: Super Simplex SL Model: L 1300 Year of manufacture: 2003 Web width: 450 to 1,320 mm Laminating width: 430 to 1,300 mm Speed: Mechanical up to 200 m/min. For materials: BOPP: 12-80 µm Dohxov E D Udozv Eqout BOPP metallized: 12-80 µm PET: 8-30 µm LDPE, LLDPE: 20-200 µm COEX: 25-200 µm ALUMINUM: 6.35-40 µm BOPA: 8-25 µm NYLON CAST: 15-80 µm PP CAST: 25-150 µm EVOH: 12-20 µm PVC: 20-500 µm COATED PAPER: 30-80 g/m2 Composites of the above materials up to 250 µm Unwind 1: Roll weight up to 1,000 kg Roll diameter up to 1,000 mm Core diameter 76 / 152 mm Side edge control Pretreatment Corona AFS AVE 150 D Unwinder 2: Roll weight up to 1,000 kg Roll diameter up to 1,000 mm Core diameter 76 / 152 mm Side edge control Corona AFS AVE 150 D pretreatment Rewinder: Roll weight up to 1,000 kg Roll diameter up to 1,000 mm Core diameter 152 mm Material thickness up to 550 µm Approx. 10 pneumatic clamping heads Approx. 10 cones Web tension: 40 to 550 N Web break monitoring Machine dimensions: Approx. 6 x 3 x 4 m high Cooling unit Infeed carriage Various coating cylinders Various spare parts Condition: Used. Now installed and in production. In good condition, according to current operators. The original price in 2003 was CHF 620,000. Availability: Approx. April 2025, or by mutual agreement. Prices are in euros, ex works, excluding Swiss VAT; no Swiss VAT and no Swiss customs duties for exports from Switzerland. The specifications are provided by the current operators and manufacturers of the systems, to the best of our knowledge, without guarantee; the goods are sold in their current condition without warranty. Payment is due 50% upon order and 50% before dismantling by the buyer; bank transfer fees are borne by the buyer. Severability clause: If individual provisions of this contract become invalid or unenforceable, the remaining provisions of this contract shall remain in effect. This contract is governed by Swiss law; the Vienna Sales Convention (CISG) is excluded. The place of jurisdiction is Pfäffikon, Zurich, Switzerland.

Condition: refurbished (used), Year of construction: 1986, Functionality: fully functional, machine/vehicle number: 86053, total width: 1,950 mm, total length: 4,000 mm, total height: 1,800 mm, overall weight: 7,500 kg, type of input current: three-phase, input voltage: 380 V, working range: 48 mm, power: 9.56 kW (13.00 HP), control voltage: 24 V, paper weight (min.): 80 g/m², paper weight (max.): 2,000 g/m², paper width (min.): 350 mm, paper width (max.): 910 mm, paper height (min.): 290 mm, paper height (max.): 670 mm, Equipment: documentation/manual, lighting, Refurbished high quality flatbed die cutting machine from Italy with Spiess insert with steel insert plate with lateral adjustment, a left and right pull attachment (Spiess), double sheet detection, moving upper platen (WUPA system or Kama) with central pressure adjustment as with KAMA, but with the conventional intermittent pull gripper bar system with closing upper grippers. In other words: the sheet moves almost in a straight path through the machine; that is why this machine is ideally suited for lighter paper and cardboard types and is definitely an excellent intermediate step between a Heidelberg SBD and a medium format 40" die-cutting machine from Bobst, for example. No break-out, sheets are laid out directly on the pallet output after die-cutting. The output contains forks to place small format pallets on. Guaranteed pressure force is 200 tons. Stroke of the moving upper platen is 48 mm. Hardened die-cutting plate and device plate. This machine has hardly been used and is in excellent condition, however we have made modifications to further increase the ergonomics and operational reliability. Can be tested at our company and can be delivered with installation and warranty. The asking price is based on this. For all information in various languages, please open the PDF containing the original folder with explanation and specifications. Some specs: Maximum paper-cardboard size 67 x 91 cm Minimum paper-cardboard size 29 x 35 cm Gripper margin 6 to 14 mm Dshxzev Nwwasv Eqsut Minimum paper weight approx. 80 -100 grs Maximum cardboard thickness 3 mm or 1.5 mm solid cardboard Stroke of the upper platen 48 mm Maximum rotation speed 4500 per hour Minimum rotation speed 1500 per hour Pressure force 200 tons Total power consumption incl. 80 m3 air pump 10 kW (13Hp) Total weight 7,500 kg The die-cutting section is transported separately from the Spiess insert and must be assembled. The electrical switch cabinet is fully plugged in with the components.

Year of construction: 1998, Condition: like new (used), Round pile feeder, first folding unit TD78/4-1 4 pockets, second unit TD66/4-2,4 pockets, 3 unit knife Stahl EF63 (1984), SBP 80 press delivery, no pump machine was on in house air supply Dohxzjd Tnxlev Eqjut

Condition: excellent (used), Year of construction: 2008, Ref: 10908 . 2008 Cauhe GH260 Guillotine Very heavy duty, large format 2.6m guillotine Equipped with: Microcut+ Flat screen colour digital programming with CIP3/4 compatibility Retractable side gauges for rear loading Infrared front table safety guard Fully enclosed rear guarding Designed to meet EN1010 Part 3 “ Cutting Machines” safety standards Double-pull down knife action, giving more power and precision cutting. Pneumatic failsafe clutch and brake system. Variable pressure hydraulic clamping. Simple and safe knife change system. Stainless steel machine table. Monitored pneumatic safety latch. Twin precision rotating ball screw back-gauge drive system. Extra cut buttons, to enable cutting from left, centre and right hand side of machine. Heavy duty - weighing in at 22,000kg Material: Paper: Bible Stock Double wax Printing Photographic Felt Duplex Bank Gummed Carbon Blotting Chromolux Parchment Writing Tissue Tracing Card Bristol Art Board: Dohxzvevmf Arj Eqsut Duplex Finish News Hardboard Straw Multiplex Wood pulp Wood/other: Veneers sandpaper felt raw rubber Leather Emery cloth Linoleum Lead foil Hard rubber cork Plastics/textiles: Acetate film Cellophane PVC Celluloid Textile fabrics Transparent film Specification: Max. cutting width: 2600mm Max. pile height: 160mm Cutting length:2600mm Front table length: 800mm Table height: 940mm Machine length: 4700mm Machine width: 4600mm Machine height: 1800mm Clamp width (min cut): 145mm Cycles per minute: 22 RPM Back-gauge speed: 150 M/s

Condition: ready for operation (used), Year of construction: 2006, A machine for the production of plastic bags is available, working width: 2x 80-550mm, working width over coupling: 1100mm, cut-off lengths: 85-800mm, max. web speed (without additional device): approx. 50m, max. working cycles: 160/min, control: Panel PC 12.1 inch TFT 800x600. With documentation, on-site inspection is possible, but not under power, was dismantled 4-5 years ago, has been regularly serviced. Dohxzev Ubqzev Eqjut

Condition: used, Year of construction: 1998, Functionality: fully functional, pressing force: 400 t, The machine is currently in production and is sold "as is." QTM converted the machine to a Siemens S7 control system in 2019. The machine will be available from May 2025. The machine can be viewed in production upon request. • For fully automatic die-cutting, creasing, and embossing with or without a gripper edge • For stripping inner waste as well as the side and rear sheet edges • For stacking the die-cut and stripped sheets with the attached gripper edges or Duehxzvsv Ubbao Eqot • For separating the gripper edges and subsequently stacking the remaining sheets • For blanking • With a patented gripper carriage register system for maximum registration accuracy • With a stack stacker that enables fully automatic separator sheet feeding and non-stop stacking and does not require conversion, even for the smallest blanks. (Shuttle table with comb structure) • Separator sheet magazine with electronic stock control, refillable during production • With Centerline equipment Processable materials Depending on material properties and sheet layout: * Paper with a basis weight of at least 80 g/m² * Cardboard or solid board up to a basis weight of 2000 g/m² * Corrugated board up to a total thickness of 4 mm (max. sheet curvature 4%) Performance data: Sheet format max. 820 x 1,130 mm min. 350 x 400 mm Max. cutting force (400 t) 4.0 MN Max. machine speed 9000 sheets/h

Year of construction: 2014, Condition: excellent (used), Offer for the Sale of a Used Technological Line for the Production of Corrugated Cardboard 1. Subject of the Offer A technological line for the production of corrugated cardboard, model WJ150-1600-3, and a cardboard drying line, model WJ150-1600/250m/min, manufactured by Techcut e.K. The machines are located in Poland and are currently in continuous operation. 2.Key Technical Data Model: WJ150-1600-3 Working width: 1600 mm Maximum speed: 250 m/min Flute types: B, C, E Optimal speed: 180-200 m/min (single wall) Dshxzsvntdaev Eqeut 100-140 m/min (double wall) The technological line includes the following components: Automatic Dry-End System Double-sided heating section: 15 heating plates x 600 mm Tension system: two sets of cotton belts Power: 31 kW Condition: very good Rotary Guillotine for Waste Rotational knives Power: 21 kW Condition: very good Cutting Knives (Single Spiral Knife) Power: 23 kW Weight: 11.2 tons Computer-controlled for precise cutting Bottom Layer Stacker Double stacker and output conveyor Power: 17 kW Steam System (Preheater) Moisture control for cardboard Power: 32 kW Waste Removal System Pressurized pipes to the shredder Waste Shredder Power: 15 kW Capacity: 1500 kg/h Knife System (Baler) Maximum pressure: 40 kN Power: 12 kW Cardboard Drying Line Includes: Single Facer (Flute B/C) Roller diameter: Ø360 mm Power: 19 kW Double Facer (Flute B/C) Roller diameter: Ø360 mm Power: 19 kW Slitter-Scorer (Longitudinal Cutter) Knives: 4, Scorers: 6 Minimum cutting width: 100 mm 3. Technical Condition The machines have been regularly serviced, are fully operational, and ready for immediate production. The technical condition is rated as "very good" under a restoration-based approach. Technical documentation and photos are available upon request. 4. Price New line price: Over €2,000,000 Used line price: €620,000 EXW, Poland 5. Benefits of the Purchase Attractive price compared to a new set. High-quality construction and reliable performance. Immediate production readiness. If interested, please contact us. Technical documentation and details regarding transport and assembly are available upon request.

Condition: excellent (used), Year of construction: 2017, Functionality: fully functional, machine/vehicle number: W400-RM-016, type of input current: three-phase, overall weight: 1,700 kg, Zemat W-18-200 Roll Die Cutting Machine Djhxjwcm Tijzv Eqsut Working width 1800mm, 100mm gap between the rollers

Year of construction: 2005, Condition: excellent (used), machine/vehicle number: 16040021064, 73 x 104 cm, Hot foil stamping and embossing machine Dohsp R Hnpjxzv Eqjut

Condition: excellent (used), Year of construction: 2017, Functionality: fully functional, type of input current: three-phase, total width: 7,000 mm, total length: 10,000 mm, total height: 2,500 mm, input voltage: 380 V, compressed air connection: 1 bar, overall weight: 22,000 kg, Sloter with reception from stacker, maximum size in passage 3300x2500mm. The machine supports E,B,C,EB,BC waves. The machine is in very good condition, All settings are from the touch panel of the machine or it is possible to set manually. The maximum speed of the machine is 150 pieces per minute. The controls and inverter of the machine are Siemens. The reason for selling is to replace the machine with a larger model. Dujhxju Dhzcezv Eqot Delivery at the expense of the buyer. I will answer all additional questions in a private message.

Condition: ready for operation (used), Year of construction: 2011, Functionality: fully functional, type of input current: three-phase, overall weight: 1,000 kg, total width: 4,300 mm, total length: 3,800 mm, input voltage: 230 V, year of last overhaul: 2024, worktable width: 1,700 mm, Gluejet 17.25 2PI. Year of production: 2011/03. The machine is almost ready for sale. All that remains is to install the gluing system at the client's request. Can be used with hot & cold glue systems. We give a warranty on all equipment we sell. Installing by our highly qualified engineers in any country in the world is possible. Dushsrq Dfcexzv Eqet

Condition: ready for operation (used), Year of construction: 1984, Minimum sheet size: 210mm/300mm, maximum sheet size: 1180mm/1600mm, production speed: 45m/min, paper weight range: 80g-600g/m², total machine length: 11000mm, total machine width: 3500mm. An on-site inspection is possible. Dohxzov T Apvev Eqeut

Condition: good (used), continuous welding machine, film welding machine -Manufacturer: Rische, continuous welding machine film welding machine Polystar -Type: Polystar 350/5 DSM-TE -Voltage: 220 V -Technical data: see photo type plate Djhxzv Eevyq Dusqout -Dimensions: 520/250/H5600 mm -Weight: 12.1 kg

Condition: used, Year of construction: 2003, Functionality: limited functionality, machine/vehicle number: 0 278 06 1192, film width: 700 mm, roll diameter: 700 mm, Used Friz rotary cutter. 1 set of blades has been resharpened. The machine is used and is sold without warranty. Inspection is possible and welcome. Djhxov Radxozv Eqeut Loading facilities available.

Year of construction: 1991, Condition: excellent (used), machine/vehicle number: 61861201, Flatpile, Vaculift, Vacubelt, DV Pump, Shingle belt delivery, MCC1 counter Machine nr: 61861201 Duohxjhqhg Aezv Eqet

Condition: ready for operation (used), Year of construction: 2000, Application: Dispersion adhesive and thermal film lamination, min. sheet size: 210mm/210mm, max. sheet size: 1000mm/1420mm, max. pile weight: 900kg, paper weight range: 50g-600g/m², film thickness range: 12µm-70µm, film type: BOPP/acetate, adhesive quantity: approx. 8g-30g/m², lamination speed: 50m/min. Including sheet feeder A-20 with Mabeg suction head, powder removal, smoothing calender, sheet separator TM-3 and pile delivery S-4. Documentation available. On-site inspection is possible. Djhjv T Ap Ajxzv Eqsut

Year of construction: 1998, Condition: excellent (used), machine/vehicle number: 66000102, Pallet feeder, Vaculift, Vacubelt, DV Pump, MBO MPC Control, ASP 66 Shingle belt press delivery Machine nr: 66000102 Duohxshqhgqezv Eqet

Condition: excellent (used), Year of construction: 2007, machine/vehicle number: 705537, infeed width: 660 mm, Maximum sheet size 660 x 1280 mm, Pallet feeder, 4 buckles first unit, First cross knife (8 pages) Second cross knife ( 16 pages) parallel buckle to the first cross knife. SB-46/MP.D Press delivery. Noise hoods, Pump, Technical documentation, Standard tools. Intergrated counter Dushxzvoqgcy Is Eqot