Used punches for sale (64)

Condition: used, Year of construction: 2001, functionality: fully functional, machine/vehicle number: 578 034 05, Bobst Autoplatine SP 104 ER Year: 2001 Serial Number: 0578 034 05 / 0531 021 05 Automatic die cutter for paper and cardboard converting, processing sheets up to 1,040 x 740 mm at up to 8,000 sheets per hour. The press is fully equipped with a waste stripping station and a blank stack delivery station with automatic non-stop and pallet changing device. Operation is controlled via the Bobst C.U.B.E. control system with an additional panel at the feeder, supported by Bernoulli sheet braking at the stripping and delivery stations. Equipment Machine Platform with safety barrier Centerline system for quick job changeovers Electronic sheet travel control Adjustable centerings at stripping and delivery stations Anti-static stainless steel plate Sheet synchronization with machine stopped 4 front lays, adjustable in pairs, with front register control Pull guide (OS) with side register control Pull guide (OOS) with side register control Double sheet detector Feed belt slow-down device Support plates at platen entry Sheet hold-down device Upper frame with manual lifting device Upper transport for paper, paperboard and corrugated board up to 4 mm 4 laterally guided transport belts Platen Press Gripper reopening device Die cutting without gripper margin Equipment centering and locking Locking of the chase against the upper beam Cutting force measurement with strain gauge Synthetic supporting plate, 22.5 mm Upper chase with quick locking, fixed bottom plate Compensating plate, 4 mm ground steel Adjustable supporting plate centerings, ±0.9 mm Lowering of the chain guides Waste Stripping Station System with 3 pull-out frames 2x upper pull-out frame 2x lower pull-out frame Central quick locking pull-out frame Blank Stack Delivery Station Automatic binder sheet inserter Gripper opening device for full sheet stacks Automatic non-stop device Special non-stop rack for small boxes below 140 mm Pile raising security Waste / skeleton removal apron Braking brush of the waste skeleton Front trim ejection control by photocells 2x upper pull-out frame Lower pull-out frame Pallet changing device with conveyor Technical Details Parameter Value Production Rate 8,000 sheets/hour Max Sheet Size 1,040 x 740 mm Min Sheet Size 400 x 350 mm Max Die-Cutting Size (with gripper margin) 1,040 x 725 mm Prodpfx Abs Afwrvsujc Max Cutting Die Size 1,050 x 746 mm Convertible Stock Paper from 80 g/m², board up to 2,000 g/m², corrugated up to 4 mm Parameter Value Max Platen Pressure 2.5 MN (250 t) Max Pile Height Feeder 1,815 mm (non-stop 1,515 mm), delivery 1,430 mm Max Pallet Size 1,200 x 800 mm Compressed Air min. 6 bar; without central supply, a compressor of 80 m³/h with 500 l tank is required Net Weight 20,000 kg Electricity Main motor 11 kW, total connected load max. 25 kVA still connected to power

Year of construction: 2001, condition: used, functionality: fully functional, Bobst Autoplatine SP 104-ER (2001) Automatic die-cutting machine for paper and cardboard converting, processing sheets up to 1,040 x 740 mm at up to 8,000 sheets per hour. The machine is fully equipped with a waste stripping station and a blank stack delivery station with automatic non-stop operation and a pallet changing device. Operation is controlled via the Bobst C.U.B.E. control system, with an additional panel at the feeder, supported by Bernoulli sheet braking at the stripping and delivery stations. Equipment ### Machine Platform with safety barrier Centerline system for quick job changeovers Electronic sheet travel control Adjustable centering at stripping and delivery stations Control cabinet cooling unit Gripper bars Bobst C.U.B.E. electronic machine operating system Additional C.U.B.E. control panel at the feeder Bernoulli sheet braking device at the stripping station Bernoulli sheet braking device at the delivery station Motor with frequency converter control ### Feeder Pile tray with handle for lateral adjustment during production Pile height adjustment with front photocell Rear pile guides (OS and OOS) Side blowers adjustable with Centerline marks Suction unit with multiple adjustments Vertical adjustment of the suction head Automatic lateral pile correction Manual non-stop device Synchronization of sheet arrival against the front lays Safety system for lowering the pile tray ### Feed Table Anti-static stainless steel plate Sheet synchronization with machine stopped 4 front lays, adjustable in pairs, with front register control Pull guide (OS) with side register control Pull guide (OOS) with side register control Double sheet detector Feed belt slow-down device Support plates at platen entry Sheet hold-down device Upper frame with manual lifting device Upper transport for paper, paperboard, and corrugated board up to 4 mm 4 laterally guided transport belts ### Platen Press Gripper reopening device Die cutting without gripper margin Equipment centering and locking Locking of the chase against the upper beam Cutting force measurement with strain gauge Synthetic supporting plate, 22.5 mm 3x upper chase with quick locking, fixed bottom plate Compensating plate, 4 mm ground steel Adjustable supporting plate centering, ±0.9 mm Lowering of the chain guides ### Technical Details Production Rate: 8,000 sheets/hour Max Sheet Size: 1,040 x 740 mm Prodpfx Abs Afv Szjuoc Min Sheet Size: 400 x 350 mm Max Die-Cutting Size (with gripper margin): 1,040 x 725 mm Max Cutting Die Size: 1,050 x 746 mm Convertible Stock: Paper from 80 g/m², board up to 2,000 g/m², corrugated up to 4 mm Max Platen Pressure: 2.5 MN (250 t) Max Pile Height: Feeder 1,815 mm (non-stop 1,515 mm), delivery 1,430 mm Max Pallet Size: 1,200 x 800 mm ### Net Weight 20,000 kg ### Electricity Main motor 11 kW, total connected load max. 25 kVA ### Note The buyer is responsible for disassembly; no tools are provided. Still connected to power.

Condition: ready for operation (used), Year of construction: 1992, functionality: fully functional, machine/vehicle number: 76-1302, overall weight: 7,900 kg, input voltage: 380 V, input frequency: 50 Hz, Schneider CNC die-cutting machine, Type 2032, with vibrating table, Type 3041 For sale is a high-performance CNC die-cutting machine from the Swiss quality manufacturer Schneider Maschinenbau AG, including a vibrating table, Type 3041. Prjdpfx Asz R Dncebuoc The system is ideally suited for processing and die-cutting cardboard, corrugated cardboard, and packaging materials. Thanks to its robust industrial design, the precise NUM-750 CNC control system, and the automatic material handling, the machine still offers an economical solution for many packaging and display applications today. Technical data, Schneider Type 2032 Year of construction: 1992 CNC control: NUM 750 Power: 28 kW Voltage: 380 V / 50 Hz Operating pressure: 100–240 bar Machine weight: approx. 7,900 kg Swiss Made Vibrating table, Type 3041 Year of construction: 1986 Power: 3 kW Weight: approx. 1,600 kg Equipment CNC-controlled die-cutting system Hydraulic clamping system Automatic material feed Pneumatic hold-down devices Includes vibrating table Extensive conveying and feeding system Condition The machine comes from industrial use and can be inspected by appointment. Sale includes all existing system components as shown in the photos. Total weight of the system: approx. 9.5 tons Inspection possible at any time by arrangement. Loading and transport are the responsibility of the buyer.

Year of construction: 1998, condition: used, functionality: fully functional, Automatic die cutter for paper and carton converting, processing sheets up to 1,040 x 740 mm at up to 8,000 sheets per hour. The press is equipped with an automatic waste stripping station and a pile delivery with manual non-stop rack and front waste removal device. Operation is controlled via the Bobst C.U.B.E. control system with an additional panel at the feeder, supported by Bernoulli sheet braking at the stripping station. Psde Afvruopfx Abusrc Equipment ###Machine Platform with safety barrier Machine elevated by 415 mm, including platform elevation Centerline system for off-press tool preparation, quick registration, and fast setting of adjustable elements Electrical cabinet with air conditioner Light beam indicator for machine state Sheet passage control unit with infrared cells 4 auxiliary control panels C.U.B.E. centralized microprocessor control unit with LCD display and keyboard for sheet counting, cutting force with adjustable overload limiter, speed setting, and synoptic status display Additional C.U.B.E. control panel at the feeder Bernoulli sheet braking device at stripping station Three-phase asynchronous main motor with frequency converter control ###Feeder Floating pallet tray with manual handle for lateral adjustment during production Suction unit with multiple adjustments Pile height control with front photocell Side blowers laterally adjustable with Centerline marks Automatic vertical compensation of the suction head Manual non-stop device Sheet synchronization device adjustable during operation ###Feed Table Anti-static stainless steel plate Upper transport for paper, carton, and corrugated board up to 4 mm Upper frame with manual lifting device 4 fixed position lower feed belts 4 paired adjustable front lays Pull guide (OS) adjustable with Centerline marks Sheet presence control and double sheet detector Sheet synchronization device with manual adjustment, machine stopped ###Platen Press 3x upper chase with quick locking, fixed bottom plate Lower ground steel cutting plate, 5 mm Lower supporting plate of synthetic material, 22.5 mm Device for die-cutting without gripper margin Gripper bar reopening device Compensation plate, 4 mm ground steel Adjustable centerings for the lower supporting plate, ±0.9 mm ###Waste Stripping Station 2x upper pull-out frame 2x lower pull-out frame Central quick lock pull-out frame ###Technical Details Production Rate: 8,000 sheets/hour Max Sheet Size: 1,040 x 740 mm Min Sheet Size: 400 x 350 mm Max Die-Cutting Size: (with gripper margin) 1,040 x 725 mm Max Cutting Die Size: 1,050 x 746 mm Convertible Stock: Paper from 80 g/m², board up to 2,000 g/m², corrugated up to 4 mm Max Platen Pressure: 2.5 MN (250 t) Max Pile Height: Feeder 1,400 mm (non-stop 1,100 mm), delivery 1,120 mm Max Pallet Size: 1,200 x 800 mm ###Compressed Air min. 6 bar; without a central supply, a compressor of 7.5 m³/h with a 110 l tank is required ###Net Weight 15,000 kg ###Electricity Main motor 11 kW, total connected load max. 25 kVA Note The buyer is responsible for disassembly; no tools are provided. Still connected to power.

Year of construction: 2006, condition: used, We offer this used Unigraphica Unicut 740 and S-74-3 Unigraphica Unicut 740 cutting machine, manufactured in 2006. Type: S-74-3 Version: S-74-3 Number: 006 Year of manufacture: 2007 Predpfx Abey N Rcboujc Fuse: 16 A Rated current: 5.0 A Power consumption: 3.0 kW Power supply: 3 x 400/230 V 50/60 Hz Formats: 7"-27" Format divisions: 1/6" and 1/8" Paper weight: 60-250 g/m2 Maximum paper width: 740 mm. GUK K72/4 KTL-F4 folding machine Year of manufacture: 1996. Equipment: 4 standard cassettes (pockets), 1 blanking cassette, 1 electric cassette for performing special folds, cassette stand. The machine is operational but incomplete. Missing the controller and optical sensor for triggering the electric cassette, missing the reciprocating knife section. Modified sheet feed control. The machine can be switched on and tested. If you have any questions or require additional information, please send us a message.

Year of construction: 1966, operating hours: 10,000 h, condition: excellent (used), functionality: fully functional, outer diameter: 420 mm, machine/vehicle number: 58256, Nebiolo Saturnia in very good condition. From first owner, at first used as a letterpress in the upcoming market with offset in the 70's. The company always produced with it's offset to maxima 50/70 size. Situated as a local printer in a village, the Nebiolo was sometimes used for rilling, slitting, scoring some offset jobs. very good machine, low noise, excellent condition of al mechanical parts. Airpump for feeder and delivery is for a later make = Becker dry-pump 100m3 with low noise. All parts necessary for the machine come with the machine, even as the original operational book and spare-parts book. The cylinder has a 6 cm larger diameter than a KBA Condor and it weights 800kgs, only 200 kgs less of that of a heidelberg SBB/SBD. The delivery is different and for carton better that that of its competitors: a triple drum delivery, turning the front side up again on the belts which transport it to the pile. Best is to replace the individual belts for one large belt and make some extra attention for laying the sheets down when coming from the belt with better air facilities. Of course we can arrange that for you either. Then you have a faster, very easy to operate and maintain with better productivity and at least the same durability (with lower noise-level due to less moving parts) than an heidelberg SBD with approx the same size for more than double the money. Really a nice product from Nebiolo even as it big brother Urania. Podpfetyyvwjx Abuorc They have pull-lays but can easily turn over to push side lays. Some specs: Max paper size 650 x 950 mm Min paper size 300 x 420 mm Speed 1500 - 4000 imp/hour Feeder pile height 550 mm Delivery pile height 650 mm Impression force approx. 35000 N (not adjustable in lighter or heavier, only one value) Bearer height 24,85 mm; machines needs "normal - Bobst standard" 23,80 diecut forms/lines with a hardened steel plate under the form so that small compensations could be made with thin band and paper under this hardened plate. This is the only and best method. A 45 to 47 HRC plate will be delivered with the machine, even as a new cylinder jacket. Feeder and delivery use an additional extern pump, Becker, 100m3, 2kW Size of the machine (approx, with steps) L x W x H = 330 x 220 x 190 cm Weight net 4,800 kgs

Year of construction: 2001, operating hours: 27,400 h, condition: good (used), functionality: fully functional, Die-cutting machine with stripping station, foundation tilting table (third-party manufacturer), tilting table/preparation table, waste stripper, electronic double-sheet detection, pull marks BS + AS, machine height increased by 300 mm, 1 die-cutting frame, various stripping frames and stripping pins (including cart), quick centering device for sheet stacks, manual non-stop feed, manual non-stop delivery, price ex works, dismantling and loading can be arranged for an additional charge! Video available upon request! In May 2026, a PLATEN CONDITIONING was carried out by BOBST on the die-cutting machine. All deposits were removed from the upper and lower tables, and the die was polished. The sector was opened and assessed as being in "like-new" condition. Photos, video, or invoice available upon request! Note: The platform must be adapted by the buyer! Longitudinal handrail missing! Technical main data: Maximum sheet size: 720 × 1020 mm, Minimum sheet size: 350 × 400 mm, Maximum die-cutting force: 250 tons (2.5 MN), Maximum production speed: 7,500 sheets per hour, Processable materials: Paper / solid board: from 80 g/m² up to 2000 g/m², corrugated board: up to 4.0 mm thick Podpfx Abszmyfdeuerc Dimensions and weight: Machine length: approx. 6,000 mm Machine width: approx. 2,000 mm Machine height: approx. 2,500 mm Total weight: approx. 19,500 kg Features of the Series II: C.U.B.E. system: Electronic Bobst machine control system Centerline system: Micrometric adjustment for fast set-up times and precise tool alignment Stripping station: Integrated double-round stripping unit for waste removal Non-stop system: Continuous sheet feeding and delivery Ultrasonic double-sheet detection

Condition: ready for operation (used), Year of construction: 2015, operating hours: 10 h, functionality: fully functional, machine/vehicle number: 2015101, Size 60 x 76 cm, die-cutting machine with automatic registration and camera system. Prodpfx Abezxf Hdjusc

Year of construction: 1990, operating hours: 21,834 h, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 059700605, Bobst SP 142-CER from 1990 for sale – Reason for sale: replacement investment made. The machine can be inspected in production. Dismantling and transport at buyer's expense. Prjdpfx Abey Htxgsuec

Condition: good (used), Year of construction: 2015, functionality: fully functional, punching force: 330 t, Machine for punching, embossing, waste removal, and separating waste sheets - as is - System equipped with a high-performance sheet feeder for automatic NON-STOP operation ⦁ For fully automatic punching, scoring, and embossing with or without gripper edges ⦁ For removing the inner waste as well as the side and rear sheet edges ⦁ For stacking the punched and removed sheets with the attached gripper edges, or ⦁ For separating the gripper edges and subsequently stacking the remaining sheets ⦁ With a patented gripper carriage register system for maximum registration accuracy ⦁ With a package stacking machine that enables fully automatic feeder operation and NON-STOP stacking, and does not need to be reconfigured even for the smallest cut sizes. (Rotary table with comb structure) ⦁ Separator magazine with electric stock control, can be refilled during production ⦁ With centerline equipment ⦁ With automatic pallet changing device in the stacker Specification Sheet format max. 760 x 1060 mm Sheet format min. 350 x 400 mm Maximum punching force 3.3 MN (330t) Speed 9,000 sheets/h Podpfx Absz H Smwjujrc Processable materials: Paper min. 80 g/m² Cardboard up to 2000 g/m² Corrugated board up to 3 mm (max. sheet curvature 4 %) Machine configuration Feeder • Fully automatic non-stop feeder with logistics for processing Euro pallets, system pallets and disposable pallets • Preset function for W4 feeder • Automatic format adjustment of the suction head • Automatic stack side limitation in the feeder System • Dyset Pro bar system • Lateral sheet alignment based on registration marks or sheet edge, max. ±10 mm • Optical side mark Punching station • Vacuum punching plate for the use of 1 mm punching plates • Pneumatic closing frame with quick-release function • Motorized punching plate fine adjustment via touchscreen, adjustment range ±1.5 mm • Motorized punching pressure adjustment Waste removal • Quick-release frame for fixed tools • Sheet guiding device • Integrated quick-release system with fine adjustment for accommodating waste removal frames with fixed tools Stacker • Quick-release frame for fixed tools • Brake brush stacker • Integrated quick-release system with fine adjustment for accommodating separating frames with fixed tools

Condition: like new (used), Year of construction: 2022, operating hours: 20 h, functionality: fully functional, machine/vehicle number: 90L1201, Polar Mohr DC-M Punching Machine – As-new condition machine in top shape! Sales price: €69,000 (plus VAT) Ex works: 2325 Himberg near Vienna, Austria Condition: Hardly used – almost as-new Availability: Immediately available Description: For sale is a Polar Mohr DC-M punching machine in excellent condition – barely used and virtually as-new. This machine is ideal for precise punching of labels, tags, and packaging components, excelling in reliability and efficiency in daily production operations. The DC-M is renowned for its user-friendly operation, compact design, and seamless integration into existing production workflows – a true quality product "Made in Germany". Technical highlights: • Precise punching quality with high productivity Prsdpswuq Afsfx Abujc • Ideal for label production and small formats • Robust construction for long-term use • Compact footprint – also suited to smaller production areas • Operator-friendly interface Viewing by appointment possible. Sale ex works (EXW) 2325 Himberg near Vienna, transport and loading available on request. 👉 Inquire now and secure an almost new Polar Mohr DC-M at an attractive price!

Year of construction: 1971, condition: excellent (used), Bobst Autoplatine 126 E Year: 1977 Maximum speed: 5500 sheets/hour Maximum size: 1260 x 920 mm Minimum size: 350 x 500 mm Maximum force: 500 tons Die-cutting Prsds Aa Ivbspfx Abusc In production Available immediately

Year of construction: 1996, condition: ready for operation (used), machine/vehicle number: 960606 (= tevens de dag dat machine fabriekspoort verlaat), PRICE LOWERED for quick deal ! Prodpfx Aexz Ncbebuec

Year of construction: 2022, condition: like new (used), functionality: fully functional, WOOKIL MEGACUT MC-2500 Die Cutter MAX. SHEET SIZE: 1800x2600 mm MAX. CUTTING SIZE: 1700x2500 mm MAX. CUTTING PRESSURE: 550 tons Pedpfoz Suafex Abusrc

Year of construction: 1997, condition: excellent (used), functionality: fully functional, machine/vehicle number: 052302303, Bobst Easypress 142, for the format 102x142cm to carry out models, test punching, preparation work for the production machine. excellent condition, year of construction 1997 Pjdpjuk I Nxofx Abuerc

Condition: refurbished (used), Year of construction: 1986, functionality: fully functional, machine/vehicle number: 86053, total width: 1,950 mm, total length: 4,000 mm, total height: 1,800 mm, overall weight: 7,500 kg, type of input current: three-phase, input voltage: 380 V, working range: 48 mm, power: 9.56 kW (13.00 HP), control voltage: 24 V, paper weight (min.): 80 g/m², paper weight (max.): 2,000 g/m², paper width (min.): 350 mm, paper width (max.): 910 mm, paper height (min.): 290 mm, paper height (max.): 670 mm, Equipment: documentation/manual, lighting, Refurbished high quality flatbed die cutting machine from Italy with Spiess insert with steel insert plate with lateral adjustment, a left and right pull attachment (Spiess), double sheet detection, moving upper platen (WUPA system or Kama) with central pressure adjustment as with KAMA, but with the conventional intermittent pull gripper bar system with closing upper grippers. In other words: the sheet moves almost in a straight path through the machine; that is why this machine is ideally suited for lighter paper and cardboard types and is definitely an excellent intermediate step between a Heidelberg SBD and a medium format 40" die-cutting machine from Bobst, for example. No break-out, sheets are laid out directly on the pallet output after die-cutting. The output contains forks to place small format pallets on. Guaranteed pressure force is 200 tons. Stroke of the moving upper platen is 48 mm. Hardened die-cutting plate and device plate. This machine has hardly been used and is in excellent condition, however we have made modifications to further increase the ergonomics and operational reliability. Pjdov Nwwaopfx Abusrc Can be tested at our company and can be delivered with installation and warranty. The asking price is based on this. For all information in various languages, please open the PDF containing the original folder with explanation and specifications. Some specs: Maximum paper-cardboard size 67 x 91 cm Minimum paper-cardboard size 29 x 35 cm Gripper margin 6 to 14 mm Minimum paper weight approx. 80 -100 grs Maximum cardboard thickness 3 mm or 1.5 mm solid cardboard Stroke of the upper platen 48 mm Maximum rotation speed 4500 per hour Minimum rotation speed 1500 per hour Pressure force 200 tons Total power consumption incl. 80 m3 air pump 10 kW (13Hp) Total weight 7,500 kg The die-cutting section is transported separately from the Spiess insert and must be assembled. The electrical switch cabinet is fully plugged in with the components.

Year of construction: 1989, operating hours: 55,929 h, condition: used, functionality: fully functional, Manufacturer: BOBST SA, Switzerland Model: AUTOPLATINE SP 142-E Year of Manufacture: 1989 Machine Type: Automatic Die-Cutting Machine Technical Specifications Operating Hours: 55929 h Non Stop sheet inserter Centerline System: Yes Delivery (automatic) Predpfx Absz Tzvisuec Maximum Sheet Size: 1,020 × 1,420 mm Minimum Sheet Size: 500 × 700 mm Maximum Production Speed: 6500 sheets/hour Maximum Die-Cutting Force: 600 tons (6 MN) Suitable Materials Cardboard: 80–2,000 g/m² Corrugated Board: F, E, R, B, FF, FE, FB and EE flute types

Year of construction: 1963, condition: used, functionality: limited functionality, machine/vehicle number: 512804, 1963 Bobst SP900E with double action stripper in reasonable/good condition. Prjdpfxotyqize Abuec Well-maintained.. in recent years for example sprocket wheels, main gripper chains, counterplate under cuttingplate, cardan joints to the feeding head, have been renewed (original Bobst parts) Gripperbars have not been renewed recently, they are still in quite a good condition. The knee joints have almost no signs of wear. they were probably at some point and the machine has not been used much since then. There is hardly any screech on them. Machine is dismantled in our storage in the South of The Netherlands, dismantled and not under power. For seriously interested potential buyers we will further upgrade the machine and assemble it and give the possibility to test it inevery way they want. In that case price will be 22,000 euros, loaded on to your transport, EX SITE

Year of construction: 2020, condition: ready for operation (used), A barely used foil die-cutting and embossing machine Kama with integrated hot foil stamping is available. Die-cutting force: 165t, max. sheet format X/Y: 760mm/600mm, min. sheet format: 279mm/210mm, max. die-cutting format X/Y: 743mm/585mm, production speed: 5500sheets/h, gripper margin: 10mm, min. paper weight: 100g/m², max. cardboard weight: 1500g/m². Machine dimensions X/Y: approx. 5000mm/2700mm/2750mm, weight: approx. 6000kg, operating hours: approx. 1000h. Including Kama AutoRegister, vacuum pump, compressor and servo main drive. Documentation available. An on-site inspection is possible. Pjdpfx Ajy Nnakobusrc

Year of construction: 2011, operating hours: 13,600 h, condition: excellent (used), functionality: fully functional, Technical data: BOBST VISIONFOIL 104 Max. sheet format: 1,040 × 740 mm Min. sheet format: 400 × 350 mm Max. embossing/hot foil stamping area: 1,010 × 702 mm Production speed: up to 7,500 sheets/hour Embossing force: up to 2.6 MN (286 US tons) Foil unwinders/web advance shafts: 2 standard Foil width: 25–1,020 mm Max. roll diameter: 250 mm Heating temperature: 20–160 °C Heating zones: 12, individually adjustable Paper: from 80 g/m² Cardboard/solid board: up to 2,000 g/m² Corrugated board: up to 4 mm Machine length: approx. 6.50 m Machine width: approx. 6.00 m Machine height: approx. 2.20 m 4 honeycomb plates Foundation exchange table (third-party product) Machine raised by 300 mm Machine is equipped with a foil braking brush (not visible in the video) or, if equipped with extraction/tube cutter, with a funnel system! High-performance machine for stable foil transport, even at high speeds and with long foil unwinders! Extremely short setup times for sheet processing and foil unwinding! Not a Chinese copy or a Bobst BMA replica! Machine has only 14,000 hours of operation! Condition very good! Podpfx Ajzt Idujbuorc Bobst platen conditioning performed (die service) 5/26 Can be inspected at any time during production, and is encouraged! Available from December/January 2026/27 Videos available upon request via WhatsApp! Direct sale to a production company preferred! No dealer options will be offered! A package deal with a Bobst 102E2 is also possible (also with an exchange table and honeycomb foundation for blind embossing)!

Condition: ready for operation (used), Year of construction: 2019, operating hours: 15 h, machine/vehicle number: MP.DBDO-00198, Size 75 x 106 cm, non-stop function in feeder and delivery, integrated fine adjustment of the cutting plate, motorized die-cutting pressure adjustment, simple operating concept. The basic model is already equipped with all functions and equipment required to start production. Short makeready times, high flexibility thanks to an extended range of materials, accommodates smaller die-cutting tools. Machine number: MP.DBDO-00198, Impressions: 15 million. Pjdpfxeyhn Uqe Abusrc

Year of construction: 1973, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 658, Available directly from our warehouse in Son; Predpfx Aexz Niujbusc heavy stamping die with electric coupling, electrical system completely renewed around 2019, original build year 1973; mechanically fully overhauled in 2015, moving die resurfaced, die pins and gears replaced with new pins of a much stronger mechanical grade than originally, as well as the bronze bearings now made from material grade 2.1061 DIN 1705; this is extremely wear-resistant with the addition of Pb (lead) for better performance and good emergency running characteristics (i.e., no lubrication), stamping plate 144 x 104 cm, thickness 5mm. Electrically upgraded with PILZ safety relays on each channel, motorized clamping of the stamping die. Maximum stamping die size with automatic clamping 900 x 1300 mm. Safety bars are much more extensive and more robust compared to the original design, 350 tons of stamping force.

Year of construction: 1968, operating hours: 35,000 h, condition: good (used), functionality: fully functional, machine/vehicle number: 7723238, 72x102cm two revolution die cutter for thin paper and light carton up to 600 grs/m2. excellent stable and very silent fast cylinder press. Locking to the floor is not necessary. Price is for each machine, NOT for the package. Package is 15% discount. Two identical machines available from the same shop, both with the same specs and the same state of maintenance. As a kind of specialist in these type of machines, I have delivered machines to this company which already had one, so at certain moment they produced with 4 machines and 6 or 7 Heidelberg Cylinder presses at half the size. maintenance always carried out by my company, so both machines have a known history, which is good. As a result of shrinking industry in The Netherlands and different types of shivering/perforating/scoring on offset presses with the cutting plates, the company went to a smaller building and only kept one Condor. In my opinion the best, fastest and strongest letterpress ever, built in this size, for sure! With less parts than a Heidelberg SBD and running much smoother. As a result of my cooperation with the KBA factory and particular Mr. Hans Bernhard Bolza-Schünemann who is the engineer responsible of the several new innovative constructions in the Condor, a small sized Condor (65x95cm) in very good original condition as a complete printing press, with some ""patina"" was donated to the Leipzig -er Museum für Printkunst (June 2002), because of its importance for the development of the printing industry in the 60's. Predpetyy Sfefx Abusc

Condition: good (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: 7555605, Max size: 60 x 41 cm, integrated feeder SE - 18.2, cross-web paper cutter ST - 18.2, die cutting unit D - 18, strapping/banding unit PB - 18.1, horizontal and vertical strapping. Paper width min. 35 x 45 mm, paper width max. 405 x 600 mm. Stacking height min. 30 mm, stacking height max. 100 mm. Machine no.: 7555605 Prsdjxc Uv Aepfx Abuec

Condition: excellent (used), functionality: fully functional, SIMPLACUTTER (CAUHE) III – 1480x1070 Machine lightly used, in very good condition Equipment: – Pneumatic clutch and brake – Control panel – Quick-mount frame (electric) + additional frame Predpfx Aoz Suarjbuec – 3 working modes: single, continuous, with time-delay on opening – Central lubrication – Additional safety covers – Service tools – Hardened pressure plate