Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Itjdpfx Agezdn H Re Ueh Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), year of last overhaul: 2025, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Itsdpszdny Rjfx Ag Uoh Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2025, volume flow: 410 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Ijdpfx Agjzdnxgs Ujth Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), Year of construction: 2009, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 x 65 cm Condition: very good! Itsdpfxozdpctj Ag Ujh Video of machine in operation available on request.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: Ijdpfozbxwiex Ag Usth 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, year of last overhaul: 2025, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: Iedjzbxvlopfx Ag Ueth The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2015, functionality: fully functional, machine/vehicle number: PBA363313, power: 4 kW (5.44 HP), Bramidan B30 W baling press, manufactured in 2015, with nameplate data for 3×230/440 V, 50/60 Hz and 4.0 kW. Specifications: Brand: Bramidan Model: B30 W Serial number: PBA363313 Year of manufacture: 2015 Voltage: 3×230/440 V Frequency: 50/60 Hz Power: 4.0 kW Current: 25/16 A Noise level: 62/64 dB Weight: 1,670 kg Iedpezd Euxjfx Ag Usth Features: Color: yellow Hydraulic unit with oil tank (designation: Q8 Handel 32 or equivalent; 32 liters) Condition: Used

Condition: good (used), Year of construction: 2015, operating hours: 1,932 h, functionality: fully functional, Bale press Presto CC 50 M, year of manufacture 2015, with lifting and tilting device. Technical data: Manufacturer: Presto Type: CC 50 M Year of manufacture: 2015 Operating hours: 1932 Pressing force: 50 t Cycle time: 52 s Drive power: 7.5 kW Feed opening: 1030 x 1100 mm Feed volume: 0.85 m³ Tying: 3-wire, manually Throughput at a bulk density of: 35 kg/m³ - 1.3 t 60 kg/m³ - 1.7 t 100 kg/m³ - 2.2 t Bale dimensions: 750 x 1100 mm Itjdpfxezc Hz Ej Ag Ujh Bale weight: 300 kg Dimensions: 4705 x 1680 x 2540 mm (L x W x H) Machine weight: approx. 4000 kg Materials: Paper, cardboard, film The operating manual is available in German. Note: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video on our website or our YouTube channel. Please note: All technical data refers to the manufacturer's specifications. We assume no liability for the information provided or any errors. This offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Baler Presto CC 40 M, Year of manufacture: 2017 Technical Specifications: Manufacturer: Presto Model: CC 40 M Year of manufacture: 2017 Pressing force: 40 t Cycle time: 34 s Drive power: 15 kW Feed opening: 1080 x 1100 mm Feed volume: 0.85 m³ Binding: 4-fold, polyester strapping, manual Throughput rate at bulk density of: 35 kg/m³ - 1.8 t/h Itsdpfx Agezc Hy Ue Ush 60 kg/m³ - 2.5 t/h 100 kg/m³ - 3.1 t/h Bale size: 750 x 1100 mm Bale weight: 400 kg Dimensions: 3650 x 1590 x 2010 mm (LxWxH) Machine weight: approx. 3,800 kg Materials: Paper, cardboard, film The baler is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Operating instructions and CE declaration are available. Note: Channel discharge is fully automatic and regulated. Please note: All technical data is based on the manufacturer's information. We do not accept liability for the information provided or any possible errors. This offer is non-binding, subject to prior sale, and may be revoked at any time. Inspections are possible by appointment. Sale is ex-works, prepayment required, without warranty or guarantee.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Strautmann bale press, type BaleTainer, pressing force 60 t, year of manufacture 2012 Technical data: Manufacturer: Strautmann Umwelttechnik Type: BaleTainer Year of manufacture: 2012 Pressing force 60 t Total connected power 30 kW Bale dimensions 1,100 x 1,100 x 800 mm (W x D x H), 3 straps Bale weight up to 400 kg (3 straps) Binding: 4-fold vertical Dimensions: 5,348 x 2,113 x 2,752 mm (L x W x H) Weight approx. 7,280 kg Materials: Paper, cardboard, PET bottles, film Note: The press is in good working order and has been inspected and tested. A video can be found on our website or YouTube channel. Itedpfxjzcuz Ts Ag Ujh Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any errors that may occur. The offer is subject to change, subject to prior sale, and may be withdrawn at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: as good as new (ex-display), Year of construction: 2026, The BTS-MF450HD special waste baler is the ideal baler for compacting difficult materials such as PET bottles, food cans and metal containers, big bags, plastic canisters and plastic packaging, but also scrap tyres and car bumpers can be reduced to a minimum of volume with the baler. The special baling press impresses with its ease of use, safe operation and its spacious filling chamber, it is ideal for medium to large amounts of material. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 30 Ton Bale weight: up to 450 kg (material depending) Bale size: 1000 H (var.) x 1200 W x 800 D mm Machine size: 3343 H x 1781 W x 1196 D mm Machine weight: 1600 kg Transport height: 2300 mm Loading aperture: 1200 W x 680 H mm Cycle times: 40 seconds Motor: 5.5 kW 16 Amp Power supply: 380 - 400 V (3 phase) Noise level: 68 dB Extra-long dual cylinders for even and early compaction of the material User-friendly lever control Bale kicker for easy eject the bales Extra retainer for reducing the material spring back Reel holder for 4 rolls of strapping A quality product “Made in Europe” Suitable for compacting PET bottles Food cans and sheet metal containers Canisters and plastic containers / packaging Scrap tyres and car bumpers Big bags Cardboard and plastic film / foils Other difficult valuable materials Optional extras Machine colour RAL PLC auto compaction cycles with bale full light and E-stop with locking key Sliding top door Ijdpfx Agovug Dyj Uoth Strapping rolls / bale wire Motor 11 kW 32 Amp Demo-Video shows BTS-MF550HD Special Waste Baler. Can Baler, Can Waste Baler, PET Baler, PET Compactor, Tyre Baler, Tire Baler, Scrap Tyre Baler, Scrap Tire Baler, Tyre Compactor, Tire Compactor, Can Baler, Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: fully functional, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating instructions, CE, electrical and hydraulic circuit diagram) is available. Iodpfxeu Thh Es Ag Usth Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), Year of construction: 1994, Brand: HSM Isdezc Hhxspfx Ag Ueth Model: 155 VL Year of construction: 1994 Pressing force: 157 kN Voltage: 400 Max. bale weight: 250 kg Bale dimensions: 110 x 70 x 95 cm Machine weight: 950 kg Machine dimensions: 144 x 100 x 234 cm Feed opening dimensions: 110 x 59 cm

Condition: ready for operation (used), Year of construction: 2015, Make: HSM Model: V-press 860 plus Year of manufacture: 2015 Press force: 418 kN Voltage: 400 Max. bale weight: 480 kg (depending on the material) Bale dimensions: 120 x 120 x 78 cm Iodpfx Agjzcrhkj Usth Machine weight: 2083 kg Machine dimensions: 180 cm x 125 cm x 298.5 cm Feed opening dimensions: 120 cm x 65 cm Video of the machine in operation available upon request. Fast delivery possible.

Condition: good (used), Year of construction: 1990, Roll compactor, Bergmann – used: Price ex works: only €950 (net) Manufacturer: Bergmann Type: PS 8100E Year of manufacture: 1990 Serial number: 05 3658 2845/90 Pressing pressure: to Weight: 750 kg Itodpfx Agozbygrj Ujh 400V, 5.5 kW Condition: good Available: from Q4/2026 Location: Hamburg Efficient waste compaction: A special steel drum enables effective collection, shredding and compaction of the waste, reducing its volume up to ninefold. Continuous filling: The machine allows for continuous filling by all users. The feed shaft can also remain open during the working process, which facilitates and accelerates waste compaction.

Condition: good (used), Year of construction: 1999, Baling presses, HSM, 30-ton pressing force – used: Price ex works: only €2,950 (net) Manufacturer: HSM Type: 225.1 VL Year of manufacture: 1999 Machine number: 6124.834. N Serial number: 200014505 Pressing force: 30 tons 400V, 5.5kW Condition: good Available: from Q4/2026 Iodpfx Agozbygfo Ujth Location: Hamburg

Condition: good (used), Year of construction: 2014, Large waste compactor / cardboard press, Höma, – used: Price at location: only €18,950 (net) for self-dismantling! Iodpfx Agezbyf Ij Ujth Manufacturer: Höma Type: PB4000 Year of manufacture: 2014 Machine number: 140409 Weight: 1,200 kg Pressing force: not specified, but we estimate 40 tons. The press has a second discharge chute. Price includes a small crane with trolley. 30 kW Condition: good Available: from Q4/2026 Location: Hamburg For an additional charge, a conveyor system for empty cardboard boxes, over 100 m long, is available! Photos at the end of the advertisement!

Condition: used, Pressing screw REG-MAC for drying films and fibers, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw Itjdpfx Aozddrdeg Ueh

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm × 65 cm Itjdpfozaqymjx Ag Ueh Condition: very good! Video of the machine in operation available upon request. Transportation is also possible.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Iodey S Rqwspfx Ag Ujth Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: used, Year of construction: 2019, functionality: fully functional, machine/vehicle number: 39117, PRESTO screw compactor with cardboard shredder and coupled container (30 m³) Isdsy N Rp Iopfx Ag Ujth

Condition: good (used), Year of construction: 1999, operating hours: 50,702 h, functionality: fully functional, Baling press Paal Konti 325 D/SO, year of manufacture 1999 Technical data: Manufacturer: Paal Type: Paal Konti 325 D/SO Year of manufacture: 1999 Operating hours: 50,702 Itsdpjyzzgnjfx Ag Ush Pressing force: 94 t Drive power: 2 x 45 kW Total connected load: 104 kW Feed opening: 1020 x 1750 mm Bale dimensions: 750 x 1100 mm, length variable Tying: 4-wire automatic Throughput at: 35 kg/m³ approx. 14 t/h 60 kg/m³ approx. 24 t/h 100 kg/m³ approx. 38 t/h Bale weight: 525 to 800 kg Transport dimensions: approx. 12352 x 2340 x 2800 mm (LxWxH) Machine weight: approx. 28,000 kg Materials: Paper, cardboard, light waste, plastic waste The press is in good working order and has been inspected and tested by us. A video can be found on our website or YouTube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any errors that may occur. This offer is subject to change, prior sale is reserved, and it can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2015, functionality: fully functional, Baling Press Dixi 60 SLD, Year of Manufacture 2015 Manufacturer: Dixi Model: Dixi 60 SLD Year of Manufacture: 2015 Drive Power: 7.5 kW, 400 V / 32 A Feed Opening: 990 x 1,110 mm (W x L) Pressing Force: 60 t Press Cycle: approx. 47 s Bale Size: 800 x 1,100 x 1,200 mm (W x H x L) Iedoy Ni Euspfx Ag Usth Bale Weight: approx. 370–410 kg Strapping: 3-fold, manual Machine Dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine Weight: approx. 5,420 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video is available on our website or YouTube channel. The operating manual and CE declaration are included. If you have any questions about the machine, we are happy to assist you by phone from Monday to Thursday, 08:00–14:00. On Fridays, we are available from 08:00–13:00. Please note: All technical data is based on information provided by the manufacturer. We do not accept any liability for the accuracy of the details or potential errors. This offer is subject to change, prior sale reserved and may be withdrawn at any time. Viewings are possible by appointment. Sales are ex works, against advance payment, without warranty or guarantee.

Condition: excellent (used), Year of construction: 2019, operating hours: 119 h, functionality: fully functional, Vertical baler HSM V-Press 860 plus B, year of manufacture 2019 Technical data: Manufacturer: HSM Model: V-Press 860 plus B Year of manufacture: 2019 Operating hours: 119 Pressing force: 60 t Drive power: 4 kW Feeding opening: 1500 x 651 mm Feeding height: 1129 mm Bale size: approx. 1500 x 1200 x 780 mm Bale weight: 550 kg Tying: manual Theoretical cycle time (idle): 25 s Theoretical pressing capacity: 32.5 m³/h Dimensions: 2099 x 1245 x 2985 mm (W x D x H) Weight: 2340 kg Iodjy I Rnujpfx Ag Ueth Materials: film, paper, cardboard Note: The baler is in very good condition. Please note: All technical data is based on manufacturer's information. We assume no liability for the details provided or any possible errors. All offers are subject to change, prior sale reserved, and may be withdrawn at any time. Viewings are possible by appointment. Sale is ex location, without warranty or guarantee. Our payment term is 100% advance payment.

Condition: good (used), Year of construction: 2021, operating hours: 245 h, functionality: fully functional, HSM V-Press 860 plus vertical baling press, year of manufacture 2021 Technical data: Manufacturer: HSM Type: V-Press 860 plus Year of manufacture: 2021 Isdpfey Tvzdex Ag Usth Operating hours: 245 Pressing force: 60 t Drive power: 4 kW Feed opening: 1195 x 645 mm Feed height: 1114 mm Bale size: approx. 1200 x 1200 x 780 mm Bale weight: 480 kg Tying: manual Theoretical cycle time in idle mode: 25 s Theoretical pressing capacity: 12 cbm/h Dimensions: 1800 x 1253 x 2990 mm (W x D x H) Weight: 2213 kg Materials: film, paper, cardboard Note: The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any possible errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Inspections are possible by arrangement. The sale takes place at our location, without warranty. Our payment terms are 100% prepayment.