Condition: excellent (used), Year of construction: 2019, HSM V Press 1160 plus Pressing force 532 kN, opening width 1,195 m, opening height 0.65 m, drive power 4 kW, press type BP, dead weight 2.43 t, transport length 1.78 m, transport width 1.568 m, transport height 2.995 m, press type baler. Cedpfx Ajl Uvukefleaa Press immediately ready for use.

Condition: excellent (used), functionality: fully functional, pressing force: 31 t, bale length: 1,200 mm, bale width: 700 mm, bale height: 800 mm, bale weight: 400 kg, overall weight: 6,200 kg, empty load weight: 6,200 kg, Equipment: documentation/manual, Baler, channel baling press. Automatic 4-wire tying. Very good condition. Serviced by the manufacturer since new. The press has undergone a complete overhaul. Adjustable bale length: 600–1200 mm. Perfect for baling paper trimmings, waste paper, film, textiles, and more. Codpfx Asxzizqofljaa

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Codpou Thbxjfx Afloaa Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2011, machine/vehicle number: 340000674, The HSM V-Press 403 baler is a compact solution for the efficient compaction of waste and recycling materials. This used baler offers excellent performance and is ideal for companies looking to optimize their waste management and save space. With its robust design and user-friendly operation, it is perfect for use in various industries. Technical details: Machine no. 6113.114 Serial number 340000674 Pressing force: 33 kN Power supply: 400 V / 50 Hz Caodpfx Ajunzn Noflea Dimensions: approx. 1,200 x 800 x 1,500 mm (L x W x H) Output: 1.1 kW Rated current: 2.6 AMP Year of construction: 2011 Weight: approx. 300 kg

Condition: ready for operation (used), Manufacturer: HSM Model: VL 155.2 Dimensions (WxDxH): 1450 x 926 x 2400 mm Cedsv Ai Tgopfx Afloaa Pressure: 16 t Filling opening: 1100 - 590 mm Filling space - 1100 - 700 x 1130 mm Bale size: 1100x700x950 mm Bale weight: 110 - 200 kg Connection: 400 V / 50 Hz Drive power: 4 kW Rated current: 8.5A Binding: 4-fold vertically Vertical capacity: 4 - 8 bales/hour Machine weight: 940 kg Year 2001-2005

Condition: good (used), Technical specifications: Briquetting press in good condition Year of manufacture: 2007 Technically inspected in 06 / 2025 Cylindrical briquette: 80 mm Throughput up to max. 150 kg/h *only approx. 3,949 operating hours Caedpfxewtdk Tj Afloa - Hydraulic press: briquetting press with discharge chute - Hydraulic unit: 4 kW - Pressure: max. 300 bar - Transport dimensions: 1585/2140/H1940 mm - Weight: 1,370 kg Functional guarantee upon handover We are happy to arrange a free test run!

Condition: used, Year of construction: 2003, Technical details: pressure: 40 t box opening: 1200 x 730 mm material: Pappe,Plaste - cardboard bottles voltage: 400 / 50 V / Hz total power requirement: 16,4 kW transport measurements machine: 6,5 x 6,2 x 2,7 m Fully automatic hydraulic CHANNEL BALL PRESS for recycling with conveyor unit/conveyor belt LxW: 4500x1000mm motor driven with automatic binding unit 3-fold bale count display/counter bale chamber LxWxH: 1800x800x800mm with 1,2m³ volume bale size LxWxH: 800x800x300-1600mm Filling opening LxW: 1200x730mm: Filling height 1200mm Hopper size LxWxH: 1200x1200x1400mm; filling height 2500mm * Cajdpfsu Nw Ezsx Aflea

Condition: used, Year of construction: 2000, operating hours: 28,155 h, Baler Paal Konti 200 D, year of manufacture 2000, optionally available with matching Paal KEM-1400 conveyor belt Technical data: Manufacturer: Paal Cjdpexgp Ibsfx Afleaa Model: Paal Konti 200 D Year of manufacture: 2000 Operating hours: 28,155 Pressing force: 60 t Drive power: 45 kW Total connected load: 60 kW Feed opening: 1020 x 1400 mm Bale dimensions: 750 x 1100 mm, variable length Binding: 4-fold automatic Throughput at 35 kg/m³: approx. 9.5 t/h 60 kg/m³: approx. 16.5 t/h 100 kg/m³: approx. 26 t/h Bale weight: 450 to 650 kg Transport dimensions: approx. 10,123 x 2,152 x 2,720 mm (LxWxH) Machine weight: approx. 15,000 kg Materials: Paper, cardboard, film The baler was dismantled from running operation. Complete documentation available. Please note: All technical data is based on information provided by the manufacturer. We do not accept liability for the details provided or for any possible errors. Subject to prior sale; the offer is non-binding and may be withdrawn at any time. Inspections are possible by prior arrangement. Sale is on a prepayment basis, ex works, without warranty or guarantee.

Condition: good (used), Year of construction: 2019, operating hours: 673 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 720 mm, bale height: 1,100 mm, overall weight: 12,500 kg, oil tank capacity: 800 l, power: 37 kW (50.31 HP), Technical data baler: Manufacturer Riko Ekos d.o.o Type S-60K (5) Year of construction 2019 Operating hours 673 hours, as of August 24 Number of pressed bales 1,127 bales, as of August 24 Pressing force main press 60 tonnes Dimensions of feed chute 1,100 x 1,400 mm Filling volume / pressing cycle 2.1 m³ Bale dimensions 720 x 1,100 mm (W x H), the length is variable Drive power 37 kW Connected load, total 47 kW Tying 4-fold horizontal, fully automatic Throughput capacity with a bulk density of 30 kg/cbm approx. 5 - 6 tonnes/hour Bulk weight of 50 kg/cbm approx. 9 - 11 tonnes/hour Bulk weight of 100 kg/cbm approx. 15 - 19 tonnes/hour Filling volume of hydraulic oil tank 800 litres PLC control Siemens SIMATIC S7-1200 Siemens SIMATIC HMI control panel Press dimensions assembled without hopper and chute 12,220 x 3,654 x 2,685 mm (L x W x H) Effective transport dimensions excluding press, with dismantled tying system 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight press 12.5 tonnes Condition of the baler: The machine is part of a sorting line and was only partially used for pressing individual material flows. The machine is now no longer needed and has therefore been sold. However, the baler is regularly put into operation once a week for two to three bales so that the machine remains in working order. Due to the extremely low operating hours, the baler is in good condition and ready for immediate use. Scope of delivery for the baler: 1 piece baler without conveyor belt, hopper and chute 8 pieces wire pulling stations, without wire 1 piece bale chute 1 set of machine documentation Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Caedpfx Aou Thicsfloa

Condition: reconditioned (used), Year of construction: 2011, functionality: fully functional, Wet waste press press container Bergmann MPB405 SN/10 for skip loader Csdpsxql Dgofx Afleaa 10cbm usable volume tested, serviced, fully functional Painting in desired RAL color possible We would be happy to make you an offer including delivery.

Year of construction: 1982, condition: good (used), machine/vehicle number: 14320, Vertical Baling Press Caodpfx Ajiuky Ijflea

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. Caedjtvau Aopfx Aflja General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: new, Year of construction: 2025, functionality: fully functional, Place: Austria Available immediately Casdpfx Aexy Nkpjflja

Condition: ready for operation (used), Baler Hsm 155 VL Bale dimensions L x W x H: 1100 x 700 x 700 - 950 mm Bale weight: 2000 - 250 kg (Cardboard) Technical data: L x W x H: 1470 x 940 x 2259 / 2439 mm Weight: 950 kg Pressure force 16 tons Power supply: 400 V (three phases) Motor power: 4 kW Bale ejector Caedpfera Nrmex Afloa Hsm 155.1 VL baler pressure force 18 tons Price of Hsm 155.1 VL baler - 2600eur Hsm 155.2 vl baler pressure force 16 tons Price of hsm 155.2 vl baler - 2800eur

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2024, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with whirlulator, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Cjdpfxju Th D Ro Aflsaa Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Caedpfx Aotvat Tjflsa After refurbishment, this baler is sold with a 2-year warranty.

Condition: like new (used), functionality: fully functional, Z1015201800 Csdsxy I D Uspfx Aflsaa Z1010880270 etc.

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: limited functionality, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), empty load weight: 4,000 kg, volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Cjdpfsu Thh Esx Afloaa Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating ins3.641tructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2008, operating hours: 23,000 h, machine/vehicle number: 00834, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,315 mm, bale width: 1,100 mm, bale height: 720 mm, warranty duration: 3 months, power: 30 kW (40.79 HP), year of last overhaul: 2025, Equipment: documentation/manual, Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler, hereby offers the following machine(s) A repaired HBC60 (30kw) Repaired – in very good technical condition Year of construction: 2008 Volume capacity m3/hr max. 365 334 321 301 Volume weight kg/m3 max. 15 30 50 80 Weight capacity T/hr max. 5.5 10 16 24 Bale weight 400 – 800 kg, depending on S.G. of material and bale length Bale length - adjustable Bale height - 720 mm Bale width - 1100 m Filling opening - 1100 mm x 1320 mm Max. size supply - 1500 mm x 1200 mm Pressure force ram - max 60 tonf. Pressure force pre-press flap - max 25 tonnes Cycle time - 18 seconds Motor - 45 kW Motor Twistomat - 2.2 kW Motor counter pressure pump - 1.1 kW Following repairs have been done in our official Bollegraaf OEM Refurbishment Workshop: * Safety doors needle installation replaced with new * Ram wheels behind replaced with new * Bronze strip above ram replaced with new * Movable beam position switch ram replaced with new * Scraper above ram replaced with new * Sealing pre press cylinders replaced with new Caedpfx Afsxck U Ueloa * New steel beams channel cylinder * nieuwe buisjes oplassen en wielen gangbaar maken * New pusher cylinder underneath vertical tying unit * Safety hatch behind needle installation replaced with new * Several cables and asi modules replaced with new * New air filter * New oil filters

Condition: good (used), Year of construction: 2019, operating hours: 2,320 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 720 mm, bale height: 1,100 mm, overall weight: 12,500 kg, oil tank capacity: 800 l, power: 37 kW (50.31 HP), Technical data baler: Manufacturer Riko Ekos d.o.o Type S-60K (6) Year of construction 2019 Operating hours 2,320 hours, as of August 24 Number of pressed bales 4,359 bales, as of August 24 Pressing force main press 60 tonnes Casdpfxsu Thipe Afloa Dimensions of feed chute 1,100 x 1,400 mm Filling volume / pressing cycle 2.1 m³ Bale dimensions 720 x 1,100 mm (W x H), the length is variable Drive power 37 kW Connected load, total 47 kW Tying 4-fold horizontal, fully automatic Throughput capacity with a bulk density of 30 kg/cbm approx. 5 - 6 tonnes/hour Bulk weight of 50 kg/cbm approx. 9 - 11 tonnes/hour Bulk weight of 100 kg/cbm approx. 15 - 19 tonnes/hour Filling volume of hydraulic oil tank 800 litres PLC control Siemens SIMATIC S7-1200 Siemens SIMATIC HMI control panel Press dimensions assembled without hopper and chute 12,220 x 3,654 x 2,685 mm (L x W x H) Effective transport dimensions excluding press, with dismantled tying system 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight press 12.5 tonnes Condition of the baler: The machine is part of a sorting line and was only partially used for pressing individual material flows. The machine is now no longer needed and has therefore been sold. However, the baler is regularly put into operation once a week for two to three bales so that the machine remains in working order. Due to the extremely low operating hours, the baler is in good condition and ready for immediate use. Scope of delivery for the baler: 1 piece baler without conveyor belt, hopper and chute 8 pieces wire pulling stations, without wire 1 piece bale chute 1 set of machine documentation Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), operating hours: 2,658 h, functionality: fully functional, pressing force: 71 t, filling opening width: 1,000 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, input current: 200 A, oil tank capacity: 1,250 l, empty load weight: 29,000 kg, Technical data baler: Manufacturer BOA Recycling Systems B.V. Type M75-45-A-5-1.6 Ecoline Year of construction 2021 Casdpfxsu Thcvo Afloa Hours of operation 2,658 hours (as of May 2024) Number of pressed bales 42,212 pieces (as of May 2024) Press power main press 71,2 kN (71 t) Specific press capacity 9 kg/cm² Operating pressure 280 bar Cylinder stroke 2,200 mm Feed channel 1,620 x 1,000 mm Capacity per cycle time 2,4 m³ Theoretic cycle time 21 seconds Theoretic throughput rate 450 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Connected load 100 kW Current consumption 200 A Tying system 5-fold vertical, fully automatic, the press stamp is prepared for an additional 3-fold horizontal binding Throughput rate at a bulk weight of 30 kg/cbm approx. 13,6 tons/hour bulk weight of 50 kg/cbm approx. 24,2 tons/hour bulk weight of 100 kg/cbm approx. 36,4 tons/hour bulk weight of 150 kg/cbm approx. 54,7 tons/hour Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,250 l SPS controller Siemens S7 1500 Operating panel Siemens SIMATIC HMI TOUCH Transport dimensions of press 10,000 x 2,800 x 3,385 mm (l x w x h) Press height set up with feed chute 4,743 mm Press height with conveyor belt 7,123 mm Machine weight baler approx. 29 tons Noise level <85 dB (A) Condition of the baler: With 2,658 operating hours, the press is almost as good as new and in very good condition, has hardly any signs of wear and is ready for immediate use. Due to larger material input quantities, the pressing force and throughput of the machine no longer meet the customer's current requirements and is therefore being replaced by a new 120 tonne baler. Only the baler is for sale, without conveyor belt and wire drawing stations. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Cjdpfx Asvf E Avefloaa Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: refurbished (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Caedpfx Aeu Th S Sofloa Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The can press was completely overhauled in our workshop. The press is in a very good condition and is sold with the 12 months OBM parts warranty. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Csdpfx Aeu Thkaofleaa Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2006, operating hours: 54,050 h, pressing force: 80 t, filling opening width: 1,020 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, oil tank capacity: 2,100 l, power: 94 kW (127.80 HP), empty load weight: 21,000 kg, Technical data baler: Manufacturer Paal Typ Konti 275 E Year of construction 2006 Hours of operation in total 54,050 hours Press power main press 80 tons at 300 bar Specific press capacity 9,7 kg/cm² Feed channel 1,600 x 1.020 mm (l x w) Throughput capacity under operating conditions 350 m³/hour Bale size 750 x 1,100 mm, length variable Driving motor 75 kW Connected load 94 kW Rated current 180 A Tying system 4-fold vertical, fully automatic Bale weight up to 750 kg, depends on material Volume hydraulic oil tank 2,100 l Caedpfxsxcxm Eo Aflsa SPS controller (manuf., type) Siemens Simatic S7-300 Operating panel (manuf., type) Siemens Multi Panel Transport dimensions only baler 11,152 x 2,152 x 3,000 mm (l x w x h) Machine weight baler approx. 21 tons Condition of the baler: The press and conveyor belt are in satisfactory working condition, see photo documentation. Further technical data and dimensions for the conveyor belt are not currently available. The plant is currently still in operation and is to be replaced by a larger press plant in the coming months. Scope of delivery: Bale press, bale chute, conveyor belt and machine documentation. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Dismantling and loading is the responsibility of the buyer. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.