Used Die Forging Press for sale (37,527)

Condition: excellent (used), Year of construction: 2016, operating hours: 27 h, SBL 1060 SE Year: 2016 Sheet feeder: Manual non-stop pile feeder Material range: Paper and board from 470 × 350 mm to 1060 × 760 mm Max cutting format: 1050 × 740 mm Min sheet size: 470 × 350 mm Max sheet size: 1060 × 760 mm Max cutting pressure: 300 tons Material thickness: 0.1 – 2 mm (corrugated/laminated max 4 mm) Min gripper margin: 9.5 mm Max inside chase size: 1155 × 852 mm Cutting plate size: 1076 × 756 mm Max speed: 8,000 sheets/hour Power consumption: Total 32 kW (22 kW + 10 kW for lower plate heating) Machine dimensions (L×W×H): 5,900 × 5,700 × 2,615 mm Max pile height – feeder (with pallet): 1,750 mm Max pile height – delivery (with pallet): 1,450 mm Feeder Section - Pneumatic feeder table - Non-stop manual feeder system Iiodpfx Aewypp Ieg Neh - Anti-static system - Pre-pile device - Manual suction group adjustment - Micrometric suction adjustment - Motorized side pile adjustment - Suction belt feeder table - High-pressure lubrication pump - 2 pneumatic side register guides - Electronic control of front and side register Cutting/Embossing Section - Automatic pressure adjustment up to 300 tons - Preparation and introduction table for die frames in platen - 2 quick-lock die chase frames with bottom plate - Pneumatic locking of the chase and lower supporting plate - Centerline System - Micrometric system - Heated lower support plate (24 mm) - Cutting plate: 4 mm - Compensation plate: 3 mm - Archiveable 1 mm thin cutting plate Stripping Section - Quick lock for upper and central stripper frames - 2 standard upper stripper frames - 2 standard lower stripper frames - Double accessory kit for lower stripper prep (pins, bars, clamps, etc.) Delivery Section - High-pile automatic non-stop delivery with conveyor - Guillotine for automatic removal of gripper margin waste - Sheet deceleration device - Tab insertion device

Condition: new, Year of construction: 2025, functionality: fully functional, stroke length: 1,750 mm, input voltage: 380 V, table width: 1,500 mm, table length: 2,000 mm, clamping force: 3,000 kN, table load: 14,600 kg, 300T Die Spotting Press Clamping Force:300T Lifting Force:82T Worktable Size:2000*1500mm Max. Daylight:1750mm Min Daylight:0mm Stroke of Bolster:3000mm Overturn capacity:7.3T Ijdpfxeug Ugho Ag Njih Overturn Degree:180° Motor Power:30Kw

Year of construction: 2005, condition: excellent (used), machine/vehicle number: 47885/05, pneumatic punching of window profiles Iiodpfx Agoff Apio Njh Stroke 20 mm

Condition: good (used), Year of construction: 2008, total height: 5,400 mm, installation height: 500 mm, table length: 2,000 mm, table width: 1,100 mm, pressing force: 250 t, overall weight: 57,000 kg, product height (max.): 4 mm, sheet thickness steel (max.): 4 mm, space requirement length: 4,800 mm, space requirement width: 2,750 mm, controller manufacturer: SIEMENS, controller model: S7 300, power: 95 kW (129.16 HP), load capacity: 2,000 kg, coil outer diameter: 2,000 mm, coil weight: 2,000 kg, coil width: 300 mm, number of straightening rollers: 7, product width (max.): 300 mm, sheet thickness (max.): 4 mm, tool height: 500 mm, CONTROLS .. electronic controls SIEMENS S7 300 PRESS DESIGN .. drive system: eccentric / crank .. openings in uprights: yes .. number of suspensions: 2 .. table cushion: no .. quick die change system: yes PRESS FORCES .. total force (nominal): 250 to PRESS TABLE .. table surface (left-right): 2000 mm .. table surface (front-back): 1100 mm .. height above floor level: 1105 mm .. opening in bed (left-right): 1700 mm .. opening in bed (front-back): 305 mm SLIDE .. table surface (left-right): 2080 mm .. table surface (front-back): 1000 mm .. stroke rate (max.): 120 /min SLIDE (MECHAN. PRESS) .. slide adjustment: 120 mm .. stroke adjustment: yes .. stroke min.: 20 mm .. stroke max.: 180 mm TOOL ASSEMBLY DIMENSIONS .. shut height (stroke down, adjustment up), BDC: 500 mm .. distance between columns (H-frame): 2055 mm .. passline opening (free passage in side columns): 810 mm DECOILER .. sheet width max.: 300 mm .. coil weight max.: 2 to .. max. diameter of coil: 2000 mm .. mandrel expansion range up to: 550 mm LEVELLER UNIT .. sheet width max.: 310 mm .. number of leveller rolls: 7 .. diameter of leveller rolls: 80 mm STRIP-FEEDER .. feeder type: roll feeder .. sheet width max.: 200 mm .. sheet thickness max.: 4 mm .. speed max.: 120 m/min ELECTRICAL SPECIFICATIONS .. total power consumption: 95 kW .. mains voltage: 400 V .. mains frequency: 50 Hz DIMENSIONS / WEIGHTS .. space requirements -left/right-: 4800 mm .. space requirements -front/back-: 2750 mm .. total height: 5400 mm .. total weight approx.: 57000 kg ATTACHMENTS (PRESSES) .. decoiler: yes .. leveller unit: yes .. European CE standards: yes Machine hours: 20,391 h (operating hours) Adjustment strokes: 20, 39, 69, 99, 125, 148, 165, 175, 180 mm Equipment: - External connecting rods for high tilt stability - Hydraulic overload protection - Press force monitoring - Temperature sensors at the bearing points - ABS AHM 2.0T decoiler (1999) Ijdpfx Agoxnwabj Noih - PBK RSD 8/6/300 straightener (2010) - Loop belt control - LW-060-02 roller feed (2008) - Advanced central lubrication system - Press force monitoring - Temperature sensors at the bearing points - Hydraulic tool clamps - Spring-loaded machine feet - Optional: Bilz air springs for an additional €7,000

Year of construction: 2022, condition: new, Pressure: 400 t table length: 3000 mm table width: 2000 mm table load max .: 50 t distance between the work tables : min. 400 / max. 2800 mm top tool foldable: 180 degrees Isdpjfn Efpjfx Ag Neih Dimensions L x W x H: 7600 × 5670 × 7850 mm Total weight (without operating materials): 85 t Motor power: 44 kW

Condition: used, CNC Press Brake AMADA Type HFBO 50 x 2000 Serial No. HFBO 50 20 S60906 Year of manufacture: 1996 Press brake with 8 axes - CNC control Operator II Iedpfjw Iq Ugox Ag Nsih Pressing force: 50 tons Working length: 2090 mm Stroke: 200 mm Frame depth: 420 mm Distance between side frames: 1660 mm Max. tool installation height: 460 mm Table width: 60 mm Table height above floor: 910 mm Motor power: 4.5 kW Mains connection: 400 Volt, 50 Hz, 20 Amp. - 8-axis CNC control Operator II (Y1-Y2 / X1-X2 / Z1-Z2 / R1-R2) - 2 freely programmable backgauge fingers, movable laterally and in height (Z1+Z2+R1+R2) - Press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and/or two-hand control panel - Mechanical lever-style tool clamping for the upper tool (5 AMADA Expert, 5 UKB 50.667 H=120 mm) - Tool holder for lower tool, 60 mm wide - 11-piece upper tool set, 30°, total length 1675 mm - consisting of: 1x 835 / 1x 300 / 1x 165 / 1x 50 / 1x 45 / 1x 35 / 1x 20 / 1x 15 / 1x 10 / 2x 100 mm (end pieces) in length - 2-piece lower tool, 88° - V8, total length 1250 mm - consisting of: 1x 835 / 1x 415 mm in length - Indicated operating hours: 30,537 h - Operating manual, electrical diagram, spare parts book included Weight: 4,700 kg Good condition

Condition: excellent (used), Year of construction: 1976, functionality: fully functional, Multi-stage cold press with a shearing device and four successive press stations Iiodep Au Ayspfx Ag Noh

Condition: used, Year of construction: 1981, stroke 610 mm strokes per minute 12 daylight - vertical 1450 mm Ijdpfxjw Sya He Ag Noih adjustment des Stößels vorhanden mm table size 2400 mm x 1370 mm die cushion Nicht vorhanden oder nich Mp 1500 unter Strom bis Oktober

Condition: used, Year of construction: 1983, nominal force 2500 t stroke 600 mm cycle time 13 - 18 s distance between columns 1720 mm Distance table/ram, max. stroke up, adjustment up 2600 mm table surface area 1720 x 1800 mm allowed max. force 4000 t blow die to die 5000 t ram surface 2100 x 1320 mm capacity of ejector in table 40 t ejector stroke in table 250 mm ejector surface area in table 900 x 820 mm capacity of ejector in ram 6 t Iiedpfx Agewmf Tvs Nsh ejector stroke in ram 40 mm spindle diameter 425 mm power requirement 900,0 kW weight 335,0 t Dimensions (WxDxH) 3,4 x 4,6 x 9,7 m height over floor 8,3 m fully automated forging line / spindle press with automation for the production of flanged shafts for hot forming only with reversible AC motor, pneumatic brake, plate ejector in table (40 t / 250 mm), ejector in ram (6 t / 40 mm), lifting device for repositioning, marking, tool change, insertion device, tilting device, loading and unloading arm, rotary table, circular oil lubrication, centralised grease lubrication cycle time approx. 13 - 18 s as is where is, WITHOUT putting into operation

Condition: good (used), Various press brake tools, punches, dies Iiedew Emf Dspfx Ag Noh Bending length 2500 + 3050 mm Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: good (used), pressing force: 150 t, Hammer weight: 150 kg Ijdpfx Agoubb Stj Neih Stroke: 480 mm Strokes: 168 p/min. Throat: 375 mm Ram diameter: 180 mm Country of origin: UK Motor power: 11 kW Machine LxWxH: 200 x 180 x 240 cm Machine weight: 6000 kg

Condition: used, Frame die-cutter - Swivel frame die-cutter - Flatbed die-cutter - Platen die-cutter - Eccentric press Punch + feed for the use of bandknife punching tools Flatbed die cutter HELMERDING type PSH 25 Com. No. EP 97784 Machine. No. 6073 Year of construction 1998 Compressive force 25 ton. Clearance between the tie rods 700 mm Table surface = installation space 800 x 670 mm Table surface = installation frame width 510 x depth 440 mm, plate thickness 20 mm Plunger surface 800 x 670 mm Hole in the table 490 x 420 mm Plunger stroke 45 mm Ram adjustment travel 10 mm Installation height = tool height 100 mm Stroke rate up to 250 strokes/min. Motor power 15 kW Mains connection 400 Volt, 50 Hz - Controlled drive for infinitely variable stroke rate - Pneumatic clutch-brake combination - ram compensation cylinder - VOGEL automatic central lubrication system - solid base plate with 4 swinging elements under the machine Iedpfx Aodzqmzeg Neih Space requirement L x W x H approx. 3000 x 2000 x 3000 mm Weight 4.5 tons good condition The machine was formerly used for cutting out cardboard blanks. Ideal for cutting out non-woven fabrics or similar for breathing masks.

Condition: ready for operation (used), Year of construction: 1955, An Eumuco screw forging press (Screw-Press) is available. Forming stages: 2, press force: 1250kN, hold-down force: 2500kN, stroke rate: 80rpm, ram stroke: 140mm, hold-down stroke + punch: 100mm, table dimensions X/Y: 680mm/680mm, ram dimensions X/Y: 680mm/680mm, drive power: 35kW. On-site inspection is possible. Isdpfjwm Nm Tex Ag Nsih

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, year of last overhaul: 2023, punching force: 300 t, We offer a choice of two identical 2006 machines. 2006 IBERICA 105 SPEED Max sheet size : 750 x1050mm, Min Sheet size : 350 x 400mm, Max mechanical speed : 9000 sph, Max impression strength : 300 tons. Max Carton board : 1.5mm, Mini Paper : 90/ 100 gm2, Max Corrugated board : 3mm, Direct Pallet loading Non stop feeder, Iijdpfxsqzhr Ds Ag Noh Full complement of infeed table furniture, Left hand side pull register lay with sensor, Touch screen, Double action stripping, Automatic Non stop delivery with belt and programmable counter, Centre line, Quicklock on chase and stripping, Micrometric thin plate system, Elevated, Complement of stripping equipment PRICE: £110,000 Ex works for either

Condition: used, Year of construction: 1979, pressure 18 t diameter 250 mm stroke 150 mm distance between columns 210 mm max. distance table - ram 400 mm power capacity 5,5 kW weight of the machine ca. 1,1 t dimensions of the machine ca. 1,0 x 1,0 x 1,8 m hydraulic die-hob press with oil-hydraulic drive, controllable dependent on pressure/time Iisdpfx Asvzxp Iog Noh as is where is, WITHOUT putting into operation Price for commissioning (in given condition) on request

Year of construction: 1986, condition: repair required (used), functionality: unexamined, machine/vehicle number: 2889 / M, Used, fully functional platen die cutter, appropriate for its age. Features include a centered clamping frame for tools, hardened die plate, and single-sided die pressure adjustment (unlike most others, where the left and right arms must be adjusted separately). Please note: the die pressure adjustment is somewhat stiff. According to the manufacturer, the central bushing—which synchronizes the right and left arms—is likely worn. Estimated cost for repair including refurbishment and transport is €10,000–€15,000. According to the manufacturer (based in Spain), repairs can only be performed at the factory. The machine is operational, though increased manual effort is currently required. Moreover, the machine's safety features are not up to current standards. All safety devices are functional: the table safety bar works, as does the rear guard at the tool. A safety cage is fitted for the side, which is included in the purchase price. The platen can be operated manually or automatically, with adjustable timing settings. We are selling the machine due to a new acquisition. Machine is still in use, available for sale at the end of October 2025. We will continue working with it until then. Iodpfxjw Tifus Ag Njih A suitable forklift is available on-site for loading. Machine weight is 5–6 tons—please ensure you have appropriate heavy-duty equipment if purchasing. Current new price is €90,000 net; the hardened die plate alone currently costs €6,200 net.

Condition: used, Bending tool, die, upper knife, upper tool, straight tool -Tool for: press brake Iodec Spnbepfx Ag Neih -Tool as: die -Thickness: 25/13 mm -Drawing with the pictures -Total length: 200 mm -Total height: 188 mm -Weight: 6 kg

Condition: used, 12-piece die block for GEWA press brake Bending tool for press brake, lower tool Isdpfx Agjwbvmio Noih Type: 0255/14 V-block size: 16 mm for 90° V-block angle: 88° Die depth: approx. 8 mm Height: 120 mm Max. pressure per meter: 100 t/m Die base width: 60 mm Total length: 4175 mm Segment lengths: 4 x 835 mm, 1 x 400 mm, 1 x 200 mm, 1 x 100 mm, 1 x 50 mm, 1 x 40 mm, 1 x 20 mm, 1 x 15 mm, 1 x 10 mm Weight: 110 kg Very good condition

Condition: ready for operation (used), Year of construction: 1964, Forming stages: 3, press force: 6500kN, stroke rate: 110rpm, ram stroke: 180mm, working range X/Y: 600mm/800mm, table dimensions X/Y: 800mm/1000mm, ram adjustment: 10mm, drive power: 37kW. On-site inspection is possible. Isdpfx Aowm Nm Hsg Neih

Condition: used, Bending tool, die, upper knife, upper tool, straight tool Iedpfx Agjfcd Imj Njih -Tool for: press brake -Tool as: die -Thickness: 25/13 mm -Drawing: with the pictures -Total length: 400 mm -Total height: 108 mm -Weight: 6.5 kg

Condition: used, 2-station notching machine and folding machine EUROMAC type Multi 220/6R Press brake, press brake, notching machine Serial no. M11941298 Year of manufacture 1998 Cutting capacity 6 mm steel at 45 kg/mm2 4 mm for stainless steel Station I (notching) Notching angle 60° to 140° (with special blade from 30° to 140°) Knife length 220 mm Table size 950 x 640 - Manual angle adjustment via hand wheels - Notching angle with built-in blade set from 60° to 140 - Hydraulic clamping of the upper and lower knives - Automatic cutting gap adjustment - sheet hold-down device - Scaled measuring tapes embedded in the table - stop rails with angle adjustment - Operation via foot switch Station II (die bending device) Pressure force 18 ton Table size 950 x 340 Working height 1100 mm - stepless lifting speed - Infinitely adjustable stroke limiter Iisdpfx Asmck Ryjg Njh - Stroke adjustment up to 30 mm working stroke - Reversible prism with 4x 90° prisms, length = 415 mm - 90° upper tool, length = 415 mm Motor power 4 kW Mains connection 400 Volt, 50 Hz Space requirement L x W x H 1150 x 1050 x 1460 mm Weight approx. 1000 kg good condition

Condition: used, Bending tool, die, upper knife, upper tool, straight tool -Tool for: press brake -Tool as: die -Thickness: 25/13 mm -Drawing: with the pictures -Total length: 400 mm -Total height: 120 mm -Price: per piece Iijdpfofcd Ilex Ag Njh -Number: 2 pieces -Weight: 13 kg

Condition: used, One-piece prism block for press brake Bending tool for press brake Reversible prism with 6 different prisms Iiedpjwbvmcjfx Ag Nsh Prism sizes: 30 mm with 3 mm radius for 90°, 40 mm with 4.5 mm radius for 90°, 50 mm with 4 mm radius for 90°, 18 mm for 90°, 10 mm for 90°, 12 mm for 45° Dimensions: 90 x 88 mm Prism length: 3000 mm Weight: 147 kg Good condition

Condition: used, Bending tool, die, upper knife, upper tool, straight tool -Tool for: press brake -Tool as: die Iiedoc Spncepfx Ag Njh -Thickness: 25 mm -Drawing with the pictures -Total length: 303 mm -Total height: 171 mm -Weight: 10 kg

Condition: used, CNC press brake FASTI type 904-125/30 serial no. 95-904-5775 year of construction 1995 Pressure capacity 125 ton. Working length 3050 mm Stroke approx. 335 mm Stand projection 300 mm Clearance between the side uprights 2550 mm Tool installation height max. 465 mm (opening width between the tool holders) Table width 90 mm (the clamping system is mounted on the table) Table height above floor 875 mm (910 mm with clamping system) Backgauge X-axis 500 mm Backgauge R-axis 115 mm Backgauge Z-axis approx. 1950 mm Lowering speed Y rapid traverse 90 mm/s Lowering speed Y-operation 8.9 mm/s Iisdpfxshmmfko Ag Nsh Return stroke speed Y-retraction 75 mm/s Oil filling approx. 160 liters Motor power 18.5 kW Mains connection 400 Volt, 50 Hz, 20 Amp. - 7-axis CNC control DELEM type DA 58 with LCD screen - 1 axis for back gauge - stop depth (X-axis) - 2 axes for back gauge - fence height (finger R1 + finger R2) - 2 axes for back gauge - stop finger, laterally movable (finger Z1 + finger Z2) - 2 axes for press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and 2-hand control panel or 2-hand control panel only - Hydraulic tool clamping for the TRUMPF upper tool system, with 20 mm clamping groove - Hydraulic tool clamping for the lower tool with 13 mm table groove, depth 21 mm (tool pin 13 x 20 mm) - FIESSLER safety light barrier, type AKAS - 2 material support arms at the front, manually movable to the side and height-adjustable - Electrical diagram, hydraulic diagram, user manual for control available - Control cabinet on the machine - without tools Space requirement L x W x H 5000 x 2500 x 3050 mm Transport dimensions L x W x H 5200 x 1900 x 2950 mm Weight 8.5 tons. Good condition