Condition: used, EKOMAL powder painting line Maximal dimension 1200 x 700 x 100, floor dimension 1800 x 1200 List of equipment: 1. three-speed spray washer with exhaust fan electrically heated. First zone of the line: - Detail washing, tub capacity of about 2 thousand liters. Electric heating. In addition, reheating was installed from the plant co. Second zone pre-rinse bath capacity of about 1 thousand liters. Gas dryer after washing with air curtains and heater. Second zone of the line - drying of the detail, heating medium propane technical or propane-butane. Riello gas burner Third zone of the line-powder booth with manipulators adapted for automatic spraying, detachable blotting paper filter blocks Third zone - painting of the workpiece, booth equipped with two manipulators and a station for manual painting. ESB control cabinet. 4th gas furnace Fourth zone - firing, gas furnace with two heaters on the upper level, siphoned. 5. continuous motion overhead conveyor with tensioning and driving station Fifth zone -Suspended conveyor with loading and unloading zone. The length of the transport chain is 112 mb. In addition, it is equipped with crossheads to facilitate loading. 112 pcs. Maximum travel speed 1m/min, adjustable from 0.3 m/min. Includes chain, drive, chain tensioning unit, control. Allows reverse gear, length 77m Cgob Hn Sjiqgkcexdst

Condition: good (used), Year of construction: 2011, Functionality: fully functional, total height: 4,000 mm, inner dimension width: 1,500 mm, inner dimension length: 6,500 mm, inner dimension height: 2,200 mm, workpiece height (max.): 2,200 mm, workpiece length (max.): 6,500 mm, Equipment: cabin, Powder coating system with workpiece size L6500mm, W1500mm, H2200mm Cgeb Hn Sxjvdlfzodot New price approx. €800 000.

Year of construction: 2025, Condition: new, Functionality: fully functional, Industrial Powder Coating Plant (Riga / LATVIA) Cgjbju Dau Ie Hn Sxdst The plant you see in the example moves with a Webb type conveyor system. The material to be powder coated is hung on the line, the system automatically follows the steps below and powder coats the material after cleaning it. After all these processes, the material is delivered from the end of the line ready for packaging. 1- Chemical Washing and Rinsing Line 2- Drying Oven 3- Powder Coating Booth with Cyclone Filter (Integrated with Robotic Painting System) 4- Curing / Polymerization Oven Each facility that is manufactured is specially designed. The evaluation is made according to the dimensions and surface types of the materials to be painted by our customer and the application project is prepared on the existing site plan. You can contact us for detailed information and offers.

Condition: ready for operation (used), Year of construction: 1997, Functionality: fully functional, Vertical painting line for aluminum profiles. It's in full operation and ready for use. It's available for inspection while it's working until early December 2024, afterwards it will be turned off for dismantling. Cgobjuzihrj Hn Sxdot

Year of construction: 2020, Condition: new, ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual.The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out. The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction.The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore. ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual. Csb Hn Sofzkzhexdjgt Filter clogging sensor The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out Automatic filter cleaning The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore.Low volume Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction. Broach through the cabin The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore.Automatic filter cleansing ROMER's cabins are equipped with an electronic automatic filter cleaning system. Booth has an adjusted range of cleaning interval, time of the impulse. Each filter can be cleaned individually by using control buttons. We know from experience that it's hard to expect from an operator to clean every single filter entirely. Thanks to this system operator won't have to worry about it anymore. Booth drive-through chain Thanks to installed drive-through chain there is no need for an operator to drag every element into the booth himself.Elements drive through the booth all on their own which improves the efficiency and allows operator to focus just on the painting part.Regulated air suction In our booths we install an anti-static plate that covers filters. It protects filters from a first wave of a powder. In a well designed booth it also improves the velocity of air moving across the painted element that reaches filters. It improves suction and makes painting easier.

Condition: new, Year of construction: 2025, Functionality: fully functional, - Box Type Electric Oven: Length:300cm, Width:150cm, Height:250cm - Powder Coating Booth with Cartridge Filter: Length:250, Width:120, Height:250cm (Internal net usage area.) - Electrostatic Powder Coating Equipment: Model: SPACESTAR MULTICOLOR, Type of Use: Manual Cgjb Hnouw T Syj Sxdst Oven 380V - 28.5 kW Powder Coating Booth: 380 - 3 kW

Year of construction: 2020, Condition: new, ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual.The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out. The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction.The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore. Csb Hjflk Akjn Sxdjgt ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual. Filter clogging sensor The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out Automatic filter cleaning The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore.Low volume Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction. Broach through the cabin The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore.Automatic filter cleansing ROMER's cabins are equipped with an electronic automatic filter cleaning system. Booth has an adjusted range of cleaning interval, time of the impulse. Each filter can be cleaned individually by using control buttons. We know from experience that it's hard to expect from an operator to clean every single filter entirely. Thanks to this system operator won't have to worry about it anymore. Booth drive-through chain Thanks to installed drive-through chain there is no need for an operator to drag every element into the booth himself.Elements drive through the booth all on their own which improves the efficiency and allows operator to focus just on the painting part.Regulated air suction In our booths we install an anti-static plate that covers filters. It protects filters from a first wave of a powder. In a well designed booth it also improves the velocity of air moving across the painted element that reaches filters. It improves suction and makes painting easier.

Year of construction: 2020, Condition: new, ROMER manipulators are characterized by quiet operation. Bmt7r28v0e They can be widely used both with simple, Cjbef Aad Ns Hn Sxdsgt as well as complex multidimensional processes They are programmed using a PLC controller Working with long and short strokes The toothed belt transmission ensures quiet operation Maintenance-free AC motor Narrow column design for space saving. The robust construction of the manipulators ensures great possibilities and high stability. The manipulator is equipped with a 7 "touch panel or is externally controlled via the ModBus protocol with RJ45 cables

Year of construction: 2020, Condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel Cgsb Hn Sjfz U Sajxdot • Paint tank capacity 6-7 kg • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, Condition: new, DESCRIPTION The demineralized water station is used to produce the so-called demi water using ion exchange technology. The station consists of 3 columns Strongly acid cation exchanger working in the sodium cycle, Strongly basic anion exchanger working in the chloride cycle, Carbon filter Our RDI-2 / RDI-4 demineralization stations are equipped with fully automatic control heads. Cgsb Hn Sofz Nakoxdot Rouezts The columns are made of AISI316L steel

Year of construction: 2020, Condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Csbefz I Rxe Hn Sxdogt Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Year of construction: 2020, Condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Cgsb Hn Ssfz I Rmsxdet Inverter Constant air flow measurement Vacuum sensor Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, Condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. Cgjb Hn Sjflmdwsxdst In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, Condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Cgjb Hnoflrc So Sxdjt Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2020, Condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO Csb Hofz Dtton Sxdogt • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Inverter Constant air flow measurement Vacuum sensor Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, Condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper Csb Hnjfz Dkgj Sxdjgt • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, Condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. Cgeb Hn Sxofz A H Dedot the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2020, Condition: new, PLC microprocessor control • HMI operator panel • Phases changed manually or automatically - temporarily • Two separate circuits for water and chemistry, closed circuit • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible The control box is made of IP54 technology User manual, Declaration of conformity, 12 months warranty. ROMER pressure washers use metal sheet that provides protection against chemicals. The washer walls protect against splashing, thanks to the closed chemistry loop, the process can be carried out with small amounts of chemistry. Due to the small amount of refrigerant required, it is easy to heat and cheaper to buy, it also allows you to wash large dimensions impossible to wash in bath tubs. Filtration system Thanks to the filtration system, the chemistry works in a closed circuit, 3 filters of different thickness are used, which prevent garbage and grease from entering the circulation. The chemistry is stored in heated stainless steel tanks from where it is fed by a pump under pressure to the lance Washing of dimensions The pressure washer allows washing of large elements, optionally has a rotating platform that allows rotation of the cleaned element, elements can be applied to it with a forklift or crane. High pressure pumps Cgobeflpmqs Hn Sxdot The car wash has two preparation phases, both treatments have separate sets of pipes, pumps, wires and guns to minimize mixing of these agents during phase change. Drains have separate valves that manage the return of funds. The carwash is equipped with a logic controller that controls all components. The chemistry is pumped up to 20 bar using a very durable, acid-resistant AISI304 pump with several stages, 3 kW. The rinsing phase uses a high pressure piston pump with ceramic pistons with a capacity of 3kW and provides 160 - 200 bar.

Year of construction: 2020, Condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Cgjbefzb Rcs Hn Sxdst Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, Condition: new, ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual.The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out. The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction.The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore. ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual. Filter clogging sensor The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out Automatic filter cleaning The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. Cob Hnefy T Tbo Sxdjgt We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore.Low volume Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction. Broach through the cabin The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore.Automatic filter cleansing ROMER's cabins are equipped with an electronic automatic filter cleaning system. Booth has an adjusted range of cleaning interval, time of the impulse. Each filter can be cleaned individually by using control buttons. We know from experience that it's hard to expect from an operator to clean every single filter entirely. Thanks to this system operator won't have to worry about it anymore. Booth drive-through chain Thanks to installed drive-through chain there is no need for an operator to drag every element into the booth himself.Elements drive through the booth all on their own which improves the efficiency and allows operator to focus just on the painting part.Regulated air suction In our booths we install an anti-static plate that covers filters. It protects filters from a first wave of a powder. In a well designed booth it also improves the velocity of air moving across the painted element that reaches filters. It improves suction and makes painting easier. Location of a plate can be regulated ROMER's powder booths are fitted with professionally made tanks, which are responsible for the collection of air needed to clean the filter. Compressed air is released from the tank in a fraction of a second while passing through the ROMER JET ™ system expands in the filter at high velocity and escapes through the micro holes in the filter cleaning it, and the

Year of construction: 2020, Condition: new, Description Automatic sprinkling chamber is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic sprinkling chamber is equipped with a set of spray pumps, it was designed so that as little liquid as possible after the process migrates to subsequent processes, thus saving money and improving the quality of washing. This is very important, because apparent savings in systems made without the use of these solutions can generate in the future much higher costs associated with chemistry and waste disposal which will simply be more. Attention should also be paid to problems with maintaining the required bath parameters. Cjb Hnofy T Szs Sxdjgt Research and development work allowed us to develop a sprinkling chamber with the function of drying details (option) with hot air blown by a set of fans after the washing process. The sprinkling chamber is equipped with an advanced system for creating your own macro programs, which can consist of 10 steps each, depending on the number of tanks, processes can be repeated, their order can be changed, etc. Each tank has its own unique icon and name, enabling the operator to work intuitively. Optionally, the tanks can be equipped with bath replenishment systems, which can be performed e.g. between processes or at the end of the cycle. • Control installed on the swivel arm for better access • PLC microprocessor control • 7 "touch operator panel • Very large number of nozzles, compared to other solutions • (Option) The possibility of drying details after the washing process • The ability to create your own advanced programs • Advanced damper system made of acid-resistant sheet metal, double protected by limit switches • Tight closing and full flap opening control system • To minimize fluid mixing, separate pipelines, nozzles, tanks for each treatment • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible • Fully automatic operation/ Prices are given in the catalog

Year of construction: 2020, Condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace. Cgjb Hn Sxsfy T Sdsdjt

Year of construction: 2020, Condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. Ceb Hn Sofx Nfmjxdogt With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, Condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. Cjb Hsflk Awsn Sxdegt History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, Condition: new, Automation Use of one photocell Using one photocell in the space of workpiece allows you to measure the length of the workpiece and, consequently, gives you the opportunity to turn on the guns when the item is in range, and to switch off the gun immediately after the workpiece is finished. The photocell is included in the standard equipme Array of guns Vertical 8pcs. pistols Control - profiControl 10 " Cyclone - CK-D1250 Dust collector - OZ-8H Center - RP-01 + SV-200 MA1-23 x 2 pcs manipulator Csb Hsflq Spon Sxdsgt Os X MX-100 x2 pcs. Horizontal goal - Horizontal goal W400 x2 items Vertical gate - H2000 vertical gate The maximum painting speed is 1,65714285714286m / min 0 piece pulling machines Pow. requires 10188m3 / h to fly Required min. cabin passage W900mm H2100mm Pipe diameter 500mm - 16.9m / s minimum 16m / s Air consumption 1210 L / min + Sug. SC-20 compressor Min.current connection 28.14 kW Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus braking the energy and powder coating. Vertical detection of the detail of the workpiece. The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. The PLC counts the time at which the detail should appear in the gun space - allowing guns to be selectively switched on or off. Application of light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to manipulate the manipulators. Benefits of using gates and photocells The benefits of using photocells or light gates are primarily energy and powder savings. Eliminate painting of a zone in which there is no detail. With the use of light gates, precise control of the guns. Our lines can be optionally equipped with photocells, or light gates Using one photocell in the workpiece space allows you to measure the length of the workpiece and, consequently, gives you the ability to turn on guns when the item appears in their range, and turn off the gun immediately after the workpiece is finished. Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus saving the energy and powder. The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. The PLC counts the time in which the detail will appear in the gun space - allowing guns to be selectively switched on or off. Using of light gates with multiple sensors horizontally and vertically This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to adjusting the manipulators. The benefits of using photocells or light gates are primarily powder and energy savings Eliminate painting of a zone in which there is no detail With the use of light gates, precise control of the guns.