Automatic powder coating line

AABO-IDEAL + GEMA

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney Lasdpfx Ahsfzb Nie Uek The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Condition: good (used), Year of construction: 2003, Main spindle: Speed range - main spindle max. 6,000 min/-1 Drive power - main spindle 16 kW Max. torque 155 Nm C-axis 360 ° Tool turret: Number of tool positions 12 pos. Number of driven tool stations 12 pos. Speed range - driven tools max. 5,000 min -1 Drive power - driven Tools 10 kW Lasdjv Drigopfx Ah Usk Tool holder (VDI 30) Tool shaft 20 x 20 mm Travel paths: x-axis 160 mm z-axis 450 mm Feed rates: Rapid traverse X: 60 m/min Rapid traverse Z: 45 m/min Feed force X: 2.5 kN Feed force Z: 4 kN Rapid traverse C: 200 1/min Max. torque C: 155 Nm Total power requirement Machine weight approx. 3.7 t Space requirement approx. 4.5 x 2.5 x 2.5 m Heidenhain control Hollow clamping cylinder C-axis and tool drive a Chip conveyor Oil and emulsion mist separator with electrostatic filter

Year of construction: 2017, operating hours: 30 h, condition: as good as new (ex-display), Belt thickness max.4 mm Strip width 300 mm Laodpfxsb Nbglo Ah Ujk Repeatability +/- 0,05 mm NC drive with compact control Feed force 3000 N (300 kg) Belt pressure max. 1,2 to

Condition: used, Year of construction: 2022, clamping force: 320 kN, displacement volume: 1,068 cm³, injection pressure: 2,120 bar, overall weight: 14,000 kg, load hours: 2,907 h, screw conveyor diameter: 65 mm, terms of delivery: FCA Pegnitz Lajdpfxjxluk Se Ah Usk delivery time: on request terms of payment: 100% prior to delivery

Year of construction: 2019, condition: as good as new (ex-display), Komplette Anlage - sofort lieferbar Pulverkabine KPZ-4 PSN Automatische Waschanlage (2-Zonen) Ledofnukljpfx Ah Usak Gas-Ofen mit Umluft SGS-80O Handschiebebahn Preis ab 99.999,00 € Netto

Condition: new, Year of construction: 2025, functionality: fully functional, As a leading manufacturer of systems for surface technology, we offer you an almost limitless portfolio for powder coating applications. At our site in 47669 Wachtendonk, we turn your individual requirements into reality and produce your desired concept. Thanks to our in-house production for almost all components, we are flexible and can respond specifically to your requirements. We not only provide you with your ideal powder coating system - we are also on hand with comprehensive user expertise to support you in all matters relating to surface technology. Every item offered here is manufactured especially for you. Whether large or small projects - we supply complete systems from a single source, tailored to your requirements. Ledstxcpwspfx Ah Uoak We look forward to hearing from you and implementing your ideas together! Example: KM Pro KM Pro electric chamber oven Heating type electric Air circulation Heating capacity 30kW Circulating air motor 3kW Insulated up to 250°C Connected load 380-400V, 34kW Floor insulation 100mm Insulation walls 150mm (highly compressed) External dimensions : 3400mm (L) x 1800mm (W) x 2550 (H) without fan motor on top and switch cabinet on the side Working dimension (inside) 3100mm (L) x 1200mm (W) x 1880m (H) Height due to the low-lying rails ≠ 2000mm Equipment - Double-wing door, incl. door bolt and handle - Adjustable air slats (optimum air circulation regulation) - 2 pcs. Heating coil - 2 PT 100 temperature sensors (top and bottom) - Exhaust air throttle flap, manual adjustment (exhaust air regulation) - 2 rails on the oven ceiling - Walls made of galvanized sheet steel Control system : - Rittal control cabinet - Hitachi panel 7 inch (touch operation) - Control via Hitachi PLC - Speed control of the air circulation motor via frequency converter, with braking resistor - Emergency off - Adjustable control power of the heating coil (if current peaks are reached, you can regulate the oven down) - GELLING function for stoving different colors in one oven (air circulation motor is throttled over a period of time) - OPEN-DOOR function regulates the air circulation downwards when the door is opened. So you have less heat loss - Traffic light to indicate the respective status. - STAY-HOME-WARM-UP is a time-controlled switch-on of the oven. This allows you to start the oven before starting work. - SEE-TEMP shows the temperature curve of the oven. This allows you to check the temperature. - GO-HOME-LEAN-BACK switches the oven off via a time control.

Year of construction: 2020, condition: new, ROMER manipulators are characterized by quiet operation. Bmt7r28v0e They can be widely used both with simple, as well as complex multidimensional processes They are programmed using a PLC controller Working with long and short strokes The toothed belt transmission ensures quiet operation Maintenance-free AC motor Narrow column design for space saving. The robust construction of the manipulators ensures great possibilities and high stability. The manipulator is equipped with a 7 "touch panel or is externally controlled via the ModBus protocol with RJ45 cables Ljdpof Aad Nofx Ah Uoak

Year of construction: 2013, condition: excellent (used), Lasermachine Amada FLC 3015 AJ Fiber year: 07/2013 Power: 2000 Watt (Fiber) Working hour: ca. 38.000 h / 14000h Available beginning of March 2023 Technical data machine: Working range: 3100 x 1550 x 100 mm Table loading weight: 920 kg Positioning speed (X/Y/Z): 120/120/120 m/min Drive technology (X/Y/Z): linear drives Max. acceleration: 30 m/s2 Laser principle: Flying optic Positioning tolerance: +/- 0,01 mm Positioning spread: +/- 0,005 mm Machine weight: 11.000kg Oscillator: Laser source: Laser diode-pumped fibre laser Type: AJ-2000 Laser power: 2000 Watt Laser wave length: 1,08 µm Stability: +/- 2% Pulse frequency: 1 – 10.000 Hz Duty range: 1-100% Control: Type: AMNC-F Screen: touchscreen Interfaces: network, USB Equipment: Automatic pallet changer High pressure cutting device (CleanCut) Aluminium cutting device Automatic gas pressure adjustment NC-focus control Sensor cutting head Diode for positioning Cutting process monitoring Safety device Cooling Cut Peripherical devices: Transformator Cooling unit Dust collector Pallet changer Operator panel Max. material thickness: Mild steel: 12 mm Stainless steel: 8 mm Alumino: 6 mm Brass: 4 mm Copper: 3 mm Technical data loading/unloading unit: Numbers of cutting pallets: 2 pieces Min. sheet size: 2000 x 1000 mm Max. sheet size: 3050 x 1525 mm Sheet thickness: 0.8 – 25 mm Laedpfx Aheirt Ewj Ujk Max. sheet weight: 920 kg Cycle time: 69 s Type of fork unload: single fork unload with roller chains Raw material stack height: 400 mm Unloading stack height: 300 mm Min. part size: 180 x180 mm Machine total height: 2650 mm

Condition: good (used), Year of construction: 2019, functionality: fully functional, inner dimension length: 7,400 mm, inner dimension width: 1,600 mm, inner dimension height: 2,200 mm, Powder Coating – Complete System for Large Parts – including Curing Oven 7,400 mm, year 2018–2021 Complete powder coating system for large parts, including: • OVEN (1): Vismont KWP-440/114 – Internal: 7,400 mm length – year 2018 • OVEN (2): Libra SLET40-25-20 – year 2020 • POWDER BOOTH: Vismont KNP-1500/06 – year 2018 • WASHING SYSTEM: Libra MR35-21-17 – year 2021 Lodpfx Ahsxrd A Ds Usak • MANUAL WASHING UNIT: Libra MR42 – year 2020 • AIR FILTRATION SYSTEM: Kemper 390600 – year 2016 • MANUAL POWDER COATING SYSTEM: Nordson Encore HD MPS – year 2021 • SCREW COMPRESSOR: Kaeser SM 15 – year 2013 • OVERHEAD CONVEYOR SYSTEM • FORKLIFT: Hyundai 30L-7A – year 2012 All equipment is in operation and fully functional. Price: Depending on partial or complete purchase.

Condition: used, Year of construction: 1999, Pressure 400 t stroke 800 mm distance between columns 2820 mm Side window 950 x 1100 mm distance table/ram (stroke up) 1600 mm table surface area 2800 x 1200 mm die cushion capacity in table 150 t die cushion stroke in table 200 mm Lasdpfx Ajv Sva Soh Uek die cushion area in table 2000 x 800 mm table height over floor 650 mm ram surface 2800 x 1200 mm speed down 420 mm/s speed up 300 mm/s working speed 17,5 - 29,5 mm/s oil volume 2500 l power requirement 75,0 + 22,0 kW Weight 50,0 t dimensions (WxDxH) 4,1 x 2,8 x 7,2 m height over floor 6,15 m permitted for manual loading according to the CE-norm with oil-hydraulic drive, controllable dependent on pressure/time and way, hydraulic drawing cushion in table, hydraulic ram interlocking, two-hand and four-hand operation