Used lowboy semi-trailers / low loaders for sale (187)

Condition: new, maximum load weight: 45,250 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. The following is an excerpt of the equipment. Complete equipment details are available upon request. Chassis, gooseneck: Special steel frame made of high-strength fine-grained steels, electrically welded at the connection points, well-dimensioned outer frame. 4-axle arrangement. Wheel arches above the axles with spray mist suppression. All steel parts are sandblasted. Lateral impact protection made of anodized aluminum installed. Increased point load of approximately 30,000 kg over approximately 4,000 mm. Special design in the gooseneck area for maximum low-bed length in combination with AluLeg support legs instead of telescopic support winches, maximum rear swivel radius of the tractor unit approximately 2,100 mm. Special superstructure with rear beam widening: DINKEL – special superstructure. Self-supporting aluminum roof beam/profile approximately 120 x 100 mm, sliding cover with plastic flaps. Rear beams can be widened to approximately 4,200 mm (only for loading and unloading). Three sliding beams per side with rubber strap relief. Additional center beam locking mechanisms in the roof beam and parking position, using a pull cable and spring latch. DINKEL – lifting roof mechanically height-adjustable. Lifting roof height approximately 400 mm, operable on both or one side, without opening the opposite side and the doors. Additional height adjustment of approximately 480 mm in approximately 40 mm increments with height adjustment in the beams. Front overhang on the front wall for operation under a tarpaulin up to a total height of approximately 4,400 mm. Four rows of stackable approximately 150 mm aluminum slats on the sides, with 450 mm pockets at the bottom and 4 rows of single pockets above. In the upper bed, only 3 rows of insertable slats. Spacing between slats evenly distributed. Floor: Approximately 27 mm special water-resistant glued beech plywood, rough surface. Steel sheet in the wheel arch area. Forklift drivable according to DIN standard. Outer frame flush with the surface. Brakes: WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve). Spring-loaded brake cylinders as parking brake. Wabco Smart Board with odometer and unit load indicator. Includes WABCO tire pressure monitoring system. Axles: 4 x 10,000 kg SAF/Sauer with drum brakes in low-bed design. Air suspension with lifting and lowering device, total lift approximately 230 mm. Third and fourth axles as friction-jointed trailing axles with electrical and mechanical lock. Twin tires: 235/75 R 17.5, -16-ply. Manufacturer of our choice, including E-wheel holder. Without E-wheel. Lighting: according to EC standard including side lights in LED design. Position lights in LED design. 2 additional reversing lights. 2 work lights on the front wall inside, at the top. Painting: Chassis and superstructure in a single color in the RAL color of your choice. Center beams, axles coated with KTL (cathodic electrodeposition) in black. Corner beams in hot-dip galvanized design. Plastic parts in black. Hot-dip galvanized parts unpainted. Rims in factory silver. Special equipment included: - E-supply cable 15-pin - Air suspension in ECAS design, operated on the semi-trailer - Overwidth signage at the front and rear in zinc-plated, continuously telescopic design with attached boundary lights including so Dsdjz Dmn Rjpfx Apmocp

Condition: new, maximum load weight: 47,300 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment list. Full specifications available on request. Gooseneck: * Gooseneck with beveled front corners (approx. 45°) and rear bevel (approx. 750 mm x 10°) * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Extendable loading platform with rear bevel (approx. 1,000 mm x 8°) * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hooking tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick; over the axles, diamond plate surface Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Tyres: * 235/75 R 17.5 3PMSF tyres, brand at our discretion Axles: * BPW axles, two rigid axles, two trailing steering axles, air-suspended, with drum brakes, lifting/lowering function * Steering axles with electromagnetically-activated reverse lock (via reverse gear or manually) * Axle tools Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit Steel structure: * Steel construction from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield 355 MPa) S690QL/S700MC (yield 690 MPa) Electrical system: * Electrical system compliant with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets (ISO standard: 24N - ISO 1185, 24S - ISO 3731, 15-pin - ISO 12098) Paintwork: * Premium and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc-rich primer Dsdpfx Ajyvnfgopmocp * High-quality 2-component (2K) single-color topcoat RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the bulkhead (without spare wheel) * 2 inch kingpin * Galvanized steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanized front connection bar * Receptacle at the rear of the gooseneck for ALU loading ramps * Galvanized drop-down supports under the loading area bevel * Bracket for a revolving beacon at the rear of the trailer * Brackets left and right on the gooseneck and rear plate for warning signs including socket * TPMS tire pressure monitoring system compliant with ECE R 141 * Removable ALU sideboards and rear wall on the gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized insert posts are removable (body length approx. 2,560 mm) * Galvanized toolbox integrated in the beveled gooseneck * 3 pairs of WADER container locks in the loading platform for one 20' (30') or one 40' container * Sliding hook-in rails for ALU loading ramps at the rear of the vehicle * 6 pairs of pockets for plug-in posts, approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with TEBS E control based on current axle load and load status * 2 LED reversing lights mounted on the rear plate * 2 pairs of ferry-

Condition: new, empty load weight: 7,200 kg, maximum load weight: 31,800 kg, overall weight: 39,000 kg, axle configuration: 3 axles, suspension: air, tire size: 235/75 R 17,5, color: other, gearing type: other, front tire size: 235/75 R 17,5, rear tire size: 235/75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Length high bed approx. 4,180 mm, length low bed approx. 9,400 mm, front wall approx. 800 mm high, 14 x stanchion pockets in the outer frame, 8 x stanchions, 3 x cross stanchion rails, 24 x lashing eyes, 4 pairs of container locks, , , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Dcodpj Aazggofx Apmjp

Condition: used, maximum load weight: 36,515 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 05/2023, next inspection (TÜV): 05/2027, Equipment: ABS, Excerpt from Equipment List: Gooseneck: Gooseneck with front corners angled approximately 45° and rear taper of approximately 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood decking approximately 30 mm thick. Extendable Loading Platform: Extendable loading platform with rear taper of approximately 1,000 mm x 8°. 5 pairs of lashing rings that fold outwards (LC 5,000 daN). 3 pairs of lashing rings that fold outwards (LC 10,000 daN). 1 pair of lashing rings lying horizontally at the front of the loading platform (LC 10,000 daN). Hardwood decking approximately 48 mm thick, with diamond plate decking over the axles. Axles: BPW axles and suspension, all axles with hydro-mechanical forced steering. Technical axle load: 12,000 kg each. Air suspension with lifting and lowering valve. Axle tool. Tires: Tires 245/70 R 17.5 3PMSF, load index (146/146 F) - manufacturer of our choice. Kingpin: JOST kingpins (mechanical) with 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load). Braking System: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Paintwork: First-class and durable corrosion protection of the standard shot-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) topcoat, solid color in RAL 3002 carmine red. Rear section metallized and painted in RAL 9010 (pure white). Metallic paint is not possible. Steel Structure: Steel structure made of high-strength fine-grain steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical System: Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the connection bar at the front with sockets 24N, 24S & 15-pin. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Includes the following additional equipment: - 2-inch kingpin - One galvanized steel front wall, approximately 400 mm high. - Yellow-red air couplings on the galvanized connection bar at the front. - 4 wheel chocks with holder on the front wall (± 5kg) - One spare wheel holder in front of the front wall. - Electro-hydraulic unit (± 45kg) - Steering from the front and rear by means of a cable remote control with push buttons, with single-axle steering control (without installation in the tractor unit) - Mounting in the rear area of the gooseneck for aluminum loading ramps. - European reflector signs (red-yellow) on the rear of the trailer. - Yellow reflector tape according to EU regulations on the side, on the extendable section and at the rear of the trailer. - On the gooseneck and on the rear panel, one holder on the left and right for warning signs including socket. - One holder for a rotating beacon on the rear of the trailer. Dcodpfx Apozqiiajmep - Galvanized folding supports under the taper of the loading platform. - One mud flap on the rear of the trailer. - Manual and description on a USB stick. - Speed stickers 80 km/h on the rear and on both sides. - Load measuring device for determining the axle loads including load chart.

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, removable, approx. 400 mm high * ASPÖCK-UNIBOX Dedpfx Aoy Auh Ijpmocp * 3 kW electro-hydraulic power unit for hydraulic functions, excluding hydraulic winches * Approx. 40 mm thick hardwood decking above the gooseneck * 2-inch kingpin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Bracket at the rear of the gooseneck for ALU loading ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the front wall * 1 pair of stake pockets recessed on the gooseneck for plug-in stakes approx. 100 x 50 mm (located on the inside of the chassis rail) EQUIPMENT: * Loading platform length approx. 8,800 mm, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * A recess in the loading platform, extending into the tapered section to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adapt to the selected loading platform length * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: each 12,000 kg with air suspension and raise/lower valve * 235/75 R 17.5 3PMSF twin tires. Manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Module B – static test load = approx. 50,000 kg * Throughout the loading platform and between the axles, interrupted approx. 50 mm thick hardwood decking (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the telescopic tube with large cross-section. Intermediate table with offset loading platform and extendable mounting rails for aluminum bridging elements * Platform locking with conically welded locking profiles every approx. 250 mm. Includes pre-tensioning plate * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck cross member, approx. 700 x 410 mm (W x D) * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom (in case vehicle is equipped with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the platform between 1st and 2nd axle * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, which can also be used as widening planks (if vehicle is equipped with extendable widenings) * Lockable aluminum elements installed on the extension tubes of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasting painted...

Condition: new, suspension: other, color: other, gearing type: other, driver cabin: other, emission class: none, fuel: biodiesel, Storage compartment for aluminum ramps, price per storage compartment, length approx. 2.48 m, width approx. 1 m, height approx. 27 cm, , --  Misprints, errors and changes reserved, sample images --, More information at: !, More details: ! Dcjdpfe Aa N R Hsx Apmop

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: Dcsdpfxsxf Silo Apmep - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: new, maximum load weight: 73,540 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Hydraulically extendable/retractable and lowerable gooseneck, length ± 3,650 mm * 2 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the middle section of the gooseneck (LC 10,600 daN) * Suitable for 6 x 4 or 8 x 4 tandem axle vehicles Compact front axle: * Hook receiver at the front and rear, length: approx. 2,200 mm * Axle width: approx. 2,850 mm Excavator bridge: * Telescopic excavator bridge with traversable bridge hooks at the front and pin-and-plate coupling at the rear * Overall width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance approx. 150 mm 4-axle rear axle: * Mechanical pin-and-plate coupling for mounting a low-bed trailer at the front * End crossbeam at the rear, axle width: approx. 2,850 mm * Axle length: approx. 5,480 mm Swivel axles, all axles hydro-mechanically force-locked * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle suspension Tires: * Front axle: * 8 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Rear axle tires: * 16 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Load index 150/148J Painting: * Complete steel construction automatically blasted with a shot blasting system after welding. Second blasting with corundum for optimal adhesion of the coating system. * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection. * Final painting with 2 layers of 2K topcoat, single-color in RAL 3002 carmine red, according to the RAL 841GL system. Including the following accessories: * Steel front panel, approx. 400 mm high * Aluminum side and rear walls, pluggable on the gooseneck, approx. 400 mm high, in anodized finish * 3.5-inch kingpin * Truck hydraulic connection with flow control (20 l/min) * Gantry for suspending the supply lines; the SZM tank must have a minimum capacity of 80 liters. * With MAX Trailer coupling parts; otherwise, coupling parts must be supplied by the customer. * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Tool kit, type No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front axle with a separate air connection for air suspension * BEKA-MAX central lubrication for a 2-axle axle with standard grease NLGI-2 * One 7-pole socket on the left and right at the rear of the front axle for warning signs * Screw-in option (approx. 40 mm diameter) every approx. 500 mm on the outside of the top chord of the outer beam of the excavator bridge for screw rings (LC 16,000 daN) * Foldable wideners with steel mats, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX central lubrication for a 4-axle axle with standard grease NLGI-2 * On the rear axle, a socket for the cable remote control of the trailing axle * Rear axle with tipper body * Two INOX toolboxes, approx. 855 x 340 x 390 mm, on the gooseneck, left and right * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the power pack, start/stop of the diesel engine Dedjxbmplspfx Apmscp

Condition: new, maximum load weight: 48,930 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck * with beveled front corners, approximately 45° and with rear bevel approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick Loading platform * in a double-extendable design with rear bevel approximately 500 mm x 8° * 5 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 4 pairs of lashing rings, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally at the front of the loading platform (LC 10,000 daN) * 1 intermediate table, approximately 250 mm * Recesses in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, with diamond plate flooring over the axles Axles * BPW axles, hydro-mechanically forced steering Dcsdozlwm Aspfx Apmop * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires * 245/70 R 17.5 3PMSF, load index (146/146 F) * TPMS tire pressure monitoring system according to ECE R 141 Kingpin * JOST kingpins (mechanical) with a 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Braking system * according to EU regulations with EBS-E (4S3M) Steel structure * made of high-strength fine-grained steel * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) * S690QL/S700MC (yield strength 690 MPa) Electrical system * according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the turn signal * ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Painting * Complete steel structure automatically blasted after welding using a blasting wheel system * Second blasting with corundum for optimal adhesion of the coating system * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Final coating with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system * Rims in silver. Rear part metallized and painted in RAL 9010 (pure white) * Metallic paint is not possible * Paint structure tested in the salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Including the following additional equipment 2 inch kingpin * Electro-hydraulic unit (± 45 kg) * Follow-up steering from the front and rear, controllable by means of a cable remote control via push buttons, with single-axle control (without installation in the central control unit) * One bracket for warning signs on the left and right of the gooseneck and on the rear panel, including socket * One bracket for a rotating beacon on the rear of the trailer * Aluminum side panels and rear panel on the gooseneck, pluggable, approximately 2,440 x 400 mm (L x H) * The rear galvanized stake pockets are removable. (Length of the superstructure approximately 2,560 mm) (± 46 kg) * A tool box, galvanized, integrated into the beveled gooseneck (± 47 kg) * 4 pairs of WADER container pockets in the loading platform for a 20', 2x 20', 40 or a 45' container (± 40 kg) * 7 pairs of stake pocket for stake pockets approximately 100 x 50 mm in the outer frame of the loading platform (± 21 kg) * Extensions, galvanized

Condition: new, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Technical Data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Total weight: 47,000 kg Saddle load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3750 mm Dodeizu Nwopfx Apmecp Saddle height loaded: 1200 mm Rear overhang: 2300 mm Loading area length: 6,850 mm Extendable by: 5,500 mm Loading height at max. load: 350 mm Frame length: 2,600 mm Loading height, rear frame at max. load approx.: 1,005 mm Suspension travel: -150/+450 mm Axle track: 1360 mm Overall width: 2,540 mm Total weight depends on the saddle load. Low-bed: Low-bed with external, extendable beams. "SUPER LOW" design, length approx. 6,850 mm. Low-bed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking mechanism. The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length. 5 pairs of lashing rings, foldable outwards (LC 10,000 daN). 6 pairs of threaded blocks on the inner beam for mounting screwable RUD rings. Rear frame: Rear frame with closed outer frame, diamond-plate flooring and continuous prism-shaped excavator well, approx. 1,250/700 x 505 mm, open at the rear. 2 pairs of lashing rings, foldable outwards (LC 10,000 daN). 1 pair of lashing rings lying in the well (LC 8,000 daN + 5,300 daN). 2 pairs of stake pockets for stake pockets 100 x 50 mm in the outer frame. Gooseneck: Gooseneck in SNT design for optimizing the loading area length, length approx. 3,785 mm. Gooseneck hydraulically adjustable up/down and extendable. Technical saddle load: 23,000 kg For semi-trailer tractor: 4x2, 6x2 and 6x4 PENDULUM AXLE: "PENDULUM AXLE", all axles hydro-mechanically forced steered. Hose burst valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinders with shut-off valves and quick-release coupling for securing in the raised position. Final coating of the axles with 2 layers of 2-component paint, solid color in "FAY-Gray-34-0260". Technical axle load: 12,000 kg Hydraulic axle equalization. Axle tool. Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the semi-trailer tractor. Electrical system: Electrical system according to EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S & 15-pin. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: Steel construction made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (Yield strength 355MPa) S690QL/S700MC (Yield strength 690MPa) Painting: First-class and durable corrosion protection of the standard shot-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat, solid color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (Pure White). Metallic paint not possible. Tires: Tires 245/70 R 17.5 3PMSF At the manufacturer's option. Load index (146/146F) Preparation for mounting screwable container positioning for 1 x 20' or 1 x 40' container on the outer beams. Without container locking mechanisms. i i2" Kingpin iA galvanized steel front wall, approx. 400 mm high. iA spare wheel with holder in front of the front wall. i2 pieces of wheel chocks with holder on the front wall. iYellow-red air couplings on the galvanized front connection bar. Steering from the front and rear by means of a cable remote control via push buttons, with single-axle control. (without installation in the semi-trailer tractor) i Hydrauli

Condition: new, overall weight: 30,000 kg, axle configuration: 2 axles, loading space length: 13,590 mm, loading space width: 2,500 mm, loading space height: 1,820 mm, total width: 2,550 mm, total height: 4,000 mm, Year of construction: 2026, Equipment: ABS, Burgers Double Deck Trailer | 2-Axle Steered NEW More volume. Lower costs. More sustainable transport. Up to 60% more loading space compared to standard trailers. In many cases, replaces 3 trailers with 2 double deckers, reducing CO₂ emissions by up to 40%. Technical Data (Model: 2-axle steered) Chassis and Running Gear Design: 2-axle, steered * Axle system: TRIDEC TF-V02, mechanical steering without electronics * Air suspension with low-maintenance bushings, lift range +160 mm / -105 mm * Axle spacing: 1,400 mm * Axle load: 2 × 9,000 kg = 18,000 kg * Permissible gross weight: 30,000 kg (12,000 kg kingpin load + 18,000 kg axle load) * Tyres: 4 × Goodyear 385/65 R22.5 on steel rims * Wheelbase and axle position adjustable according to loading scheme * Wheel housings with wear blocks and anti-spray mudflaps * Fully hot-dip galvanized chassis to ZINQ standard Brake and Safety Systems WABCO 2-line air brake system * Drum brakes 420 × 180 mm * ABS/EBS-E with ECAS (level control), ELEX, and RSS (electronic stability control) * Visible indicator lights for ABS/EBS and ECAS Dimensions External dimensions (L × W × H): 13,820 × 2,550 × 4,045 mm * Upper deck internal dimensions: Length 13,590 mm × Width 2,500 mm × Height 1,820 mm * Lower deck internal dimensions: Length 9,940 mm × Width 2,500 mm × Height 1,820 mm * Lower deck height from ground: 320 mm Bodywork and Materials Side walls: 21 mm plywood, coated inside and out with white polyester * Front wall: 24 mm plywood, both sides polyester white * Roof: 30 mm insulated polyester panel, white, with rainwater drainage * Floors: Aluminium profiles (top and bottom), non-slip, grey coated * Stainless steel front and corner profiles, L-profiles on side flaps Access and Operation Three side flaps (battery compartment, lift/smartboard control, technical access) * Multi-deck lift Dhollandia DH-VH (2,500 kg lifting capacity, hydraulic folding tip, LED platform lighting, foldable handrails and ramps) * Lift control: external operation on the right, integrated into the fence * Spare wheel not included Electrics and Lighting LED interior lighting upper and lower deck * Complete LED exterior lighting: position, marker, reverse, and work lights * Additional LED for platform lighting * Power supply via 2 × 230 Ah batteries, charging via tractor unit * Main switch behind side flap, coupled with lift control * WABCO Smartboard: weight display, odometer, adjustable loading/unloading heights Finish and Paintwork External colour: RAL 1003 yellow (non-metallic) including wheel wells, stainless steel front and rear * Reflectors: 3M partial contour marking (white sides, red rear) * Advertising space possible (optional) Benefits 60% more loading space – replaces up to 3 standard trailers with 2 double decks * 40% lower CO₂ emissions – eco-friendly and economical * ROI often within just 1 year * Customisable (axles, cooling, dimensions) Dodpfsw I Iinex Apmecp * Suitable for long-haul and distribution transport Available Configurations at Burgers: 2-axle standard – rigid or steered, 13.60 × 2.55 × 4.00 m * 3-axle standard – rigid or with steered axle * City trailer – max. 11.50 m, always steered * Special dimensions – height up to 4.25 m depending on national regulations * Body: plywood or insulated, optionally with cooling and temperature zones * Extras: tail lift, hydraulic ramp, solar modules, cameras, aerodynamic profiles, LED packages For further information, we are happy to assist you.

Condition: new, maximum load weight: 40,017 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, Year of construction: 2026, Technical Description Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm hardwood flooring. Loading Platform: 5 pairs of folding external lashing rings (LC 5,000 daN). 3 pairs of folding external lashing rings (LC 10,000 daN). 1 pair of flat-mounted lashing rings at the front of the loading platform (LC 10,000 daN). Approx. 48 mm thick hardwood flooring, checker plate covering over the axles. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Dcedpfxjw Dl Hqe Apmjp 205/65 R17.5 tyres as per manufacturer's specification. TPMS: TPMS tyre pressure monitoring system compliant with ECE R 141. Data transmission to the tractor unit via the standardised EBS interface according to ISO 11992. To ensure correct display, the tractor unit must be capable of transmitting and displaying this data. Axles: BPW axles, two fixed axles, two self-steering axles, air-suspended, with drum brake, with lifting/lowering function. The self-steering axles can be locked electronically via reverse gear or manually using an electromagnet. Axle tools included. Brake System: WABCO brake system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit. Electrical System: Electrical system according to EU regulations, 24 volt LED lighting by ASPÖCK-NORDIK (ASS3). All LED side marker lamps flash with the turn indicators. ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. Connections conform to ISO standards: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Construction: Steel structure made from high-strength fine-grained steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Paintwork: The entire steel structure is automatically shot-blasted with a turbine system after welding. A second abrasive blasting treatment with corundum ensures optimal adhesion of the coating system. HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for superior corrosion protection. Final coating with 2 coats of 2K topcoat, single-colour in a shade of your choice according to the RAL 841GL system. Rear section metallized and painted in RAL 9010 (pure white). Metallic paint not possible. Paint system tested in salt spray test according to ISO 9227-NSS. Cavities sealed with special wax. Options included: 2" kingpin One galvanized steel bulkhead. Yellow-red air couplings on the galvanized front connection panel. 2 wheel chocks with holders on the bulkhead. Fixture at the rear of the gooseneck for ALU approach ramps. Further options upon request.

Condition: new, maximum load weight: 36,040 kg, overall weight: 53,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm * Gooseneck hydraulically raisable/lowerable and extendable * For tractor unit: 6 x 4 or 8 x 4 Low-bed: * Low-bed with external beams in an extendable SUPER LOW design, length approx. 8,000 mm * Low-bed with a fixed hardwood floor approx. 40 mm thick and mechanical locking system * The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length * 7 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 6 pairs of threaded blocks on the inner beam for mounting screw-on RUD rings Rear chassis: * Rear chassis with closed outer frame and diamond plate cover * Chassis with excavator bucket, which is closed in the rear half to accommodate the air tanks * 3 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 1 pair of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally, at the front and rear of the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires: * Tires 245/70 R 17.5 3PMSF - at the manufacturer's choice. Load index (146/146F) Braking system: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paint: Dcodsy Uwu Ispfx Apmjp * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Topcoat with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system Includes accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * Trailer steering, operable from the front and rear via cable remote control with push buttons, with single-axle steering control (without installation in the tractor unit) * Preparation for mounting screw-on container positioning for 1 x 20', 1 x 40' or 1 x 45' containers on the outer beams. Without container locking mechanisms * Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw couplings * Electro-hydraulic unit * Spiral cable for supplying the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with plug connection (NATO-NATO) * Yellow reflector tape according to EU regulations on the side, on the extension and at the rear of the semi-trailer * On the gooseneck and at the rear, left and right, one bracket each for the warning signs, including a socket * Manual and description on a USB stick * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pumps * 7 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD VLBG-4 rings * 2nd driving height, approx. 50 mm above the normal driving position, by means of manual operation * On the gooseneck, plug-in aluminum side panels and rear panel, approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in frames are removable (length of the superstructure

Condition: new, overall weight: 80,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, More vehicles available. Excerpt from the equipment list below. Full equipment details on request. GOOSENECK: * Gooseneck in SNT design, optimized for loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * Suitable for tractors: 4 x 2, 6 x 2, and 6 x 4 * Detachable steel front wall, approx. 400 mm high Dodpfx Apjxarmaemjcp * ASPÖCK-UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling all hydraulic functions except hydraulic winches * Gooseneck outer rail with mounting holes for screwable lashing rings. First hole approx. 200 mm from front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at rear part of gooseneck (LC 10,000 daN) * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Approx. 40 mm hardwood floor covering on gooseneck, checker plate covering over kingpin * 3.5-inch kingpin * Gooseneck guide plate for the fifth wheel, approx. 500 mm wide * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) * 2 pairs of lashing rings with retention spring hanging on the outer rails of the gooseneck (LC 5,000 daN) LOADING PLATFORM: * Extendable loading platform, length approx. 8,800 mm with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical lock bolt and reinforced locking positions; supply lines routed securely inside the extendable rails, automatically adapting to the current platform length * BPW axles and suspension; 1st axle steerable, all others force-steered via hydro-mechanics * 1st axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting/lowering valve * 235/75 R 17.5 3PMSF twin tires – brand at our discretion * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B – static test load 50,000 kg * Full-length hardwood floor, interrupted between axles, approx. 50 mm thick (increases slip resistance). – Long slots for removable and repositionable bridging elements * At the front of the platform – 1 movable intermediate table, approx. 300 mm wide, for the large-cross-section sliding tube, with checker plate covering. – Front and rear with long slots for removable and repositionable bridging elements * 1 pair of lashing rings on front cross member (LC 10,000 daN) * 7 pairs of flush-mounted, fold-out lashing rings in the outer frame of the platform (LC 10,000 daN) * Extendable (galvanized) widened sections, approx. 230 mm per side (without wooden planks) * 1 pair of mechanical rear supports * Rear steering operable from front and rear via cable remote control, with single-track control of axles, without installation on the tractor * TPMS tire pressure monitoring sensors fitted to all wheels * Deck locking with conically welded locking profiles every 500 mm * Lock monitoring left and right on the trailer * Mechanical lock for intermediate table (approx. 300 mm wide) to secure the table when extended * 5 pairs of threaded blocks mounted on the extendable rail for the installation of M20 screw-in rings (LC 5,000 daN) BRAKING SYSTEM

Condition: new, maximum load weight: 38,953 kg, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, MAX100-N-3B-9.30-U Technical Data Speed: 80 km/h Total weight: 49,500 kg Saddle load: 18,000 kg Axle load: 31,500 kg Unladen weight (+/- 3%): 10,547 kg Payload approx.: 38,953 kg Gooseneck length: 3850 mm Saddle height loaded: 1200 mm Loading platform length: 9300 mm Extendable by: 0 mm Axle distance: 1360 mm Rear deflection radius: 2300 mm Loading height at max. load: 860 mm Overall width: 2540 mm Suspension travel: -55 / +145 mm Technical Description Gooseneck: Gooseneck with beveled front corners at 45° and a rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Loading platform: Loading platform after the gooseneck, hydraulically raisable and lowerable, length approx. 2,800 mm, with a rear bevel of approx. 1,000 mm x 8°. 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of lashing rings that can be folded inwards on the central beam at the front (LC 10,000 daN). Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN). Hardwood flooring approx. 48 mm thick, with non-slip steel plate flooring over the axles. Ramps: Two-piece steel ramps, one pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood flooring. Ramp with hydraulically raising and folding ramp sections, hydraulic lifting mechanism and hydraulically adjustable. Maximum load per pair: 40,000 kg Kingpin: JOST kingpins (mechanical) with a 2-speed gearbox for a 24t lifting capacity (50t test load). Dsdjg Sk Tropfx Apmjcp Tires: Tires 235/75 R 17.5, as selected by the manufacturer. Axle: SAF axles, air-suspended, with drum brakes, with raising/lowering function. The last axle is steered with an electro-magnetic reverse steering lock, which can be activated via reverse gear or manually. Axle tool. Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel structure: Steel structure made of high-strength fine-grained steels. Steel qualities: S355J2+N / S355MC (yield strength 355 MPa) S690QL / S700MC (yield strength 690 MPa) Painting: First-class and durable corrosion protection of the standard bead-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) topcoat in a single color in RAL colors of your choice. Rear part metallized and painted in RAL 9010 (pure white). Metallic paint is not possible. Electrical system: Electrical system according to EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection bar at the front with 24N, 24S & 15-pin sockets. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Included accessories 2" kingpin One galvanized steel front wall, approx. 400 mm high. Yellow-red air couplings on the galvanized connection bar at the front. 4 pieces of wheel chocks with holders on the front wall. (± 5 kg) Cable for supplying the electro-hydraulic unit and/or the electric winch (35mm², 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with plug connection (ANDERSON-ANDERSON) Galvanized folding supports under the bevel of the loading platform. One bracket for a rotating beacon on the rear of the semi-trailer. Operating valves for the ramps mounted on the right side of the semi-trailer. (± 4 kg) Yellow reflector tape according to EU regulations on the side and r

Condition: new, functionality: fully functional, Year of construction: 2026, Equipment: ABS, EBS, 2+1 Axle Platform Trailer Dcedpfsyaxthjx Apmop

Condition: new, maximum load weight: 34,104 kg, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Further information here: Dedov D Abgopfx Apmocp

Condition: new, maximum load weight: 90,700 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, total width: 2,850 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Extract from the specifications. Complete equipment list available upon request. Gooseneck: Gooseneck hydraulically liftable/lowerable and detachable. Length approx. 3,650 mm. For tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at the front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * Lowbed ATX-A with telescopic longitudinal beams in low design with fixed hardwood floor approx. 50 mm thick * With drive-over bridging hooks at the front and pin-lug coupling at the rear * Base width: approx. 2,850 mm, Length: approx. 7,150 mm, Beam height: approx. 330 mm, Beam width: approx. 750 mm * Loading height approx. 480 mm with ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical pin-lug coupling for mounting a lowbed at the front, rear end traverse at the back * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendle axle 3-axle front bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position Dcedpfxow Tgp De Apmep * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Front bogie tires: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Rear bogie tires: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Final coat with 2 layers of 2-component topcoat, single color in RAL 3002 Carmine Red, according to RAL system 841GL Includes accessories: * Steel front bulkhead, approx. 400 mm high * Plug-in ALU side and rear boards on the gooseneck, approx. 400 mm high, anodized finish * 3.5 kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections at the gooseneck * Front bogie with a separate air connection for pneumatic screwdriver * BEKA-MAX central lubrication for a 3-axle bogie * Preparation for mounting of bolt-on container locks for 1 x 20' or 1 x 30' containers on the outer beams * Without container locks * Mounts for foldable extensions outside on the outer beams of the loading area * One 7-pin socket left and right, front and rear on the rear bogie for warning signs * BEKA-MAX central lubrication for a 5-axle bogie * Socket on the rear bogie for the cable remote control of the steering override * Rear bogie with trough * 2 LED reverse lights mounted on the rear panel * European reflector panels (red-yellow) at the rear * One mud flap at the rear * One LED beacon with bracket left and right on the rear traverse * Two INOX toolboxes 855 x 340 x 390 mm on the gooseneck, left and right * 1-cycle

Condition: new, maximum load weight: 48,300 kg, overall weight: 71,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available for immediate and short-term delivery, on our website. Extract from the equipment features. Full specification available on request. GOOSENECK: * Gooseneck with integrated 1-axle running gear (pendulum axle) in detachable design * Gooseneck hydraulically liftable and lowerable, including hydraulic coupling connected with the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with a front taper of approx. 60° * Saddle load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Front bulkhead made of steel, detachable, approx. 400 mm high, with chamfered design * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside on the front bulkhead of the gooseneck with lifting arm * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings in the outer frame of the front chassis, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings at the transition between chassis and loading platform (LC 10,600 daN) * On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized finish * On the gooseneck, 1 plug-in aluminium tailboard, approx. 400 mm high, anodized finish * 3.5-inch king pin * TPMS tire pressure monitoring system compliant with ECE R 141 * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 1 INOX toolbox with 1 lid, mounted on top of the gooseneck on the right in the direction of travel near the aluminium drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING AREA: * Lowbed with external main beams, designed as a telescopic loading platform in low-profile layout with front extension including a fixed approx. 50 mm hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical pin-lug coupling from the lowbed to the chassis to exchange the platform or install extension beams * 1 locking position every approx. 500 mm in the extension section * 4 pairs of recessed lashing rings arranged lengthwise on the loading area, distributed along the outer frame/main beam (LC 10,000 daN) * 1 lashing ring per side on the outside of the rear crossmember (LC 10,000 daN) * Foldable widening sections, approx. 230 mm per side (WITHOUT timber planks) * Detachable widening planks, steel-edged * Preparation for installation of bolt-on container positioning devices for 1x 20' or 1x 40' container on the main beams. Container locks not included * 6 pairs of threaded blocks between the lashing rings under the upper flange on the main beam for mounting screw-type M24 rings (LC 8,000 daN) * 2 pairs of M24 screw rings (LC 8,000 daN) included REAR RUNNING GEAR: Dedpfxeyhkqno Apmocp * Rear running gear with closed external frame, checker plate decking and continuous prism-shaped excavator recess, approx. 1,450 x 900 x 505 mm, open at rear * Pendulum axle, all axles hydro-mechanically forced steered * Hose burst valve on the axle compensation cylinders with automatic reset function * Hydraulic cylinders with shut-off cocks and pre-insertion facility for securing in raised position * Final paint on axles in 2 coats of 2-pack paint, solid colour DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF. Brand at our discretion * Remote steering from front and rear via cable-control, with axle alig

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-Axle MULTIMAX "PLUS" semi-trailer, air-suspended and with hydraulically forced steering axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h (legal) Total weight: 49500 kg / 31500 kg Fifth wheel load: 18000 kg Axle load: 31500 kg / 31500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin offset to rear approx.: 2,100 mm Fifth wheel height loaded approx.: 1205 mm Platform length approx.: 9,600 mm Extendable by approx.: ? Platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55 / +145 mm Axle spacing: 1,360 mm Total weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific regulations. Technical description Gooseneck: Gooseneck in SNT design to optimize platform length, length approx. 3,900 mm, rear with a bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor-trailer combinations: 4 x 2 and 6 x 2. Platform: Platform, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6°. Platform behind the gooseneck can be hydraulically raised and lowered, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating deck. Hydraulically folding ramp ends. Ramps can be individually hydraulically shifted outwards by approx. 235 mm and inwards by approx. 365 mm. Maximum load and angle of inclination according to technical data sheet: C470319 Maximum inclination angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tool. Tires: 235/75 R 17.5 3PMSF, twin tires. Manufacturer according to our choice Load index 143/141J (144/144F) Braking system: Braking system of the brand WABCO EBS-E according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" design according to EU regulations. (ASS 3) Metallization: Complete HRM metallization (High Resistance Metallization) Complete steel structure shot-blasted, then hot-dip galvanized with ZINACOR 850 (Zinc 85% - Aluminum 15%). Painting: 6-coat finish: Complete steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion primer. Top coat with 2 coats of 2-component paint (acrylic), solid color in RAL colors of your choice, followed by sealing of the cavities with special wax. Rims in silver. Multi-color and special paint finishes available at an extra cost. Steel structure: Steel structure made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders tested according to DIN-EN 287-1. Welding process MAG according to EN ISO 4063. Protective gas M21 according to EN ISO 14175 Dedpjizu Ntefx Apmocp Front wall made of steel, plug-in, approx. 400 mm high Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the connection strip at the front with sockets 24N, 24S & 15-pole. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pole connection according to ISO-12098 If your pin assignment differs from the ISO connection standard, please inform us. "Anderson" socket on the connection strip at

Condition: new, maximum load weight: 35,800 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment. Complete equipment available upon request. Dodjz Dmnwepfx Apmscp Chassis, gooseneck: Special steel frame made of high-strength fine-grain steels, electrically welded at the connection points, well-dimensioned outer frame. 3-axle arrangement. Wheel arch above the axles with spray mist suppression. All steel parts sandblasted. Lateral impact protection made of anodized aluminum mounted. Increased point load of approx. 30,000 kg over approx. 5,000 mm. Special design in the gooseneck area for maximum possible low-bed length in combination with the AluLeg outrigger supports, instead of telescopic outrigger winches, max. rear pivoting radius of the semi-trailer tractor unit 2,100 mm. Special superstructure with rear girder widening: DINKEL - special superstructure. Self-supporting aluminum roof beam / profile approx. 100 x 100 mm, sliding tarpaulin with plastic flaps. Rear girders can be widened to approx. 4,200 mm (only for loading and unloading). Three sliding girders per side with rubber strap relief. Additional center girder locking in the roof beam and parking position, by means of a pull cable and spring latch. DINKEL - lifting roof, mechanically height-adjustable. Lifting roof height approx. 400 mm, operable on both sides or on one side. Without opening the opposite side and the doors. Additional height adjustment of approx. 480 mm in approx. 40 mm increments, with height adjustment in the girders. Front cover on the front wall for operation under a tarpaulin up to a total height of 4,400 mm. Four rows of stackable approx. 150 mm aluminum slats on the side, with 450 mm pockets at the bottom, above 4 rows of individual pockets. In the upper bed, only 3 rows of insert slats. Evenly distributed spacing. Floor: approx. 27 mm special water-resistant glued beech - screen-printing panels, rough surface. Steel sheet in the wheel arch area. Forklift-compatible according to DIN standard. Outer frame flush with the surface. Brakes: WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (parking/release safety valve). Spring brake cylinders as parking brake. Wabco Smart Board with odometer and unit load display. Including WABCO tire pressure monitoring system. Axles: 3 x 10,000 kg SAF/Sauer with drum brakes in a low-bed design. Air suspension with lifting and lowering device, total stroke approx. 230 mm. Third axle as a friction-controlled trailing axle with electric and mechanical lock. Twin tires: 235/75 R 17.5, -12-ply. Premium brand of our choice, including E-wheel chocks. Lighting: according to EC standard including side lights in LED design. Position lights in LED design. 2 additional reversing lights. 2 work lights on the front wall inside, top. Painting: Chassis with superstructure in RAL color of your choice. Center girders, axles powder-coated black. Corner girders in hot-dip galvanized design. Plastic parts black. Hot-dip galvanized parts unpainted. Rims in factory silver. Special equipment including: - E-supply line 15-pin - Air suspension in ECAS design, operation on the semi-trailer - Overwidth signs front and rear in galvanized, steplessly telescopic design with attached marker lights including sockets for flashing beacons (small signs) - Center girders with additional roof beam locking, by means of a pull cable - operation from below - Sliding tarpaulin support unlocking also from

Condition: new, maximum load weight: 27,000 kg, overall weight: 36,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, crane, Step-frame semi-trailer in roll-off tipper design 3 axles with disc brakes SAF axles Lift axle Tires 385/55 R 22.5 Gear-driven winch LED lighting Work lights 25-ton capacity in sliding/articulated design for container lengths up to 7,500 mm Roller height approx. 1,300 mm Hydraulic internal locking Soft stop Quick release Fifth wheel as loading platform with side boards Djdpszirgxefx Apmscp 1 unit available in stock. Different equipment/design available on request. Further information available on request.

Condition: new, maximum load weight: 25,300 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment details. Full specifications available upon request. Neck (Gooseneck) * Gooseneck in SNT design to optimize loading platform length * Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2 Kessel Bridge (Tiefbett section) * Low bed designed as extendable Kessel bridge in SUPER LOW design * Approx. 6,850 mm length * With mechanical locking * Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length Rear Chassis * Short version with closed outer frame and checker plate cover * Chassis with excavator trough, closed at the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve Tires * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Brake system * Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit Paintwork * 6-Coat final treatment * All-steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver grey * Drop side color: Natural aluminum Dsdpov Sw E Asfx Apmscp Accessories included * Removable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit * Spare wheel carrier in front of the gooseneck front wall * Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN) * 2" king pin * Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly * Air connection with air gun at the gooseneck * 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Outer side beams of the loading area prepared for removable loading floor * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN) * Cut-outs above the lashing rings in the outer carrier’s upper flange * Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings * The outer carriers of the low bed coated with anti-slip sand finish for slip resistance * 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit * 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Front and rear tapers

Condition: new, maximum load weight: 36,156 kg, overall weight: 45,000 kg, axle configuration: 3 axles, Year of construction: 2026, MAX200-N-3A-13.60-19.5-2.54 Technical Data Speed: 80 km/h Total weight: 45,000 kg Fifth wheel load: 18,000 kg Axle load: 27,000 kg Unladen weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Loading area length: 13,600 mm Fifth wheel height, loaded: 950 -> 1050 mm Rear overhang: 2,300 mm Extendable by: 3,400 mm Wheelbase: 1,360/1,405 mm Overall width: 2,540 mm Technical Description Loading area: Extendable loading platform with pneumatically operated locking mechanism. 2 pairs of lashing rings (LC 5,000 daN). Dsdpfx Apsg Sk Tvjmscp 1 pair of lashing rings (LC 10,000 daN). 6 pairs of lashing rings, foldable outwards (LC 5,000 daN). 2 pairs of lashing rings, foldable outwards (LC 10,000 daN). Cutouts in the outer frame of the loading platform for attaching lashing straps (LC 2,000 daN). Fifth wheel: JOST fifth wheel (mechanical) with 2-speed gearbox for 24t Load capacity (50t test load). Axles: SAF axles: SAF CD axles, air-suspended, with disc brakes (377 mm), with lift/lower function (ET 120). The trailing axles with electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. (± 80 kg) Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel construction made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Painting: First-class and durable corrosion protection of the standard shot-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) topcoat, solid color, in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). Metallic paint is not possible. Electrical system: Electrical system according to EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Included Accessories Yellow-red air couplings on the galvanized connection strip at the front. 2 chocks with holders. 2" King Pin A galvanized steel front panel approx. 2200 mm high. (± 105 kg) EN12642-XL Yellow reflector tape according to EU regulations on the side, on the extension and at the rear of the trailer. European reflector signs (red-yellow) at the rear of the trailer. Loading area with approximately 38 mm thick hardwood floor. (± 320 kg) 10 pairs of pocket rails for plug-in rails 100 x 50 mm in the outer frame of the loading platform. (± 30 kg) 1 spare wheel holder under the loading platform on the right side, in the direction of travel. Tires 435/50 R 19.5, at the manufacturer's choice. One mudflap at the rear of the trailer. Manual and description on a USB stick. One mounting for a rotating beacon at the rear of the trailer. On the swan neck and at the rear panel, left and right, one mounting each for warning signs including socket. One INOX tool box transversely under the loading platform (1000x400x2500) (± 135 kg) 6 pairs of WADER container pockets in the loading area, for 1x20' container, 2 x 20' containers or 1 x 40' container; an additional locking point is provided in the extension for a 45' container. (± 90 kg) 4 pairs of WADER container locks. (± 60 kg) 10 pairs of galvanized plug-in rails approx. 100 x 50 mm, 1,000 mm high. (± 220 kg) 3 pairs of pocket rail strips, mounted transversely in the loading area, for plug-in rails 100 x 50 mm. (± 95 kg) S

Condition: new, maximum load weight: 44,000 kg, overall weight: 61,000 kg, axle configuration: 3 axles, Year of construction: 2026, Further information here: Djdpfxjv D Abtj Apmocp