Feeder line

Coiltech Feeder line

Condition: good (used), Year of construction: 2002, Manufacturer: BRÜCK Tip: 12/1600 Load capacity: 12000 kg Max sheet width: 1600mm Coil diameter: 1800mm Weight : cca 14 t Nlodpfx Ahshrnbko Uek Without control cabinet!

Condition: reconditioned (used), Year of construction: 1983, Power: 2.000 kN Frequency: 60 rpm Stroke, adjustable: 20 - 120 mm Daylight: 450mm (max. stroke up) Ram adjustement: 100mm Size of bolster: 850 x 810mm Opening in bolster: 00 x 50mm Ram area: 750 x 810mm Motor power: 22 kW equipped by: - 1pc. con rod - 6pc. guideways - hydraulic overload - motorized oil lubrication - motorized ram adjustment - manuel stroke adjustment - pneumatic ram balancing cylinder - anti vibration machine feet Nsdjgpxc Sspfx Ah Uolk

Condition: used, Year of construction: 1980, machine/vehicle number: A-07/471A, sheet width - max.:130 mm straightening roll diameter:40 mm :5 :2+2 sheet thickness - min.:0,4 mm sheet thickness - max.:3,5 mm weight:0,4 t Njdpscxxx Rjfx Ah Uelk dimensions of the machine ca.:0,6x0,65x1,15 m with integrated, stepless adjustable Vari-drive, reversing, operating-mode switch for manual and automatic operation, introduction roller cage, position indicator of straightening rolls via analogue display, adjustment of straightening rollers via hand wheels, automatic swivel arm control, very good condition

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load Nlsdpohlnzkefx Ah Ujk - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Year of construction: 1971, condition: good (used), decoiler - expansion mandrel with coil lifting table strip width: 1.200 mm strip thickness: 0,3 - 5 mm coil weight: 10 t Nlodped Ha E Sjfx Ah Ujk mandrel Ø: 508 mm

Condition: new, pressure: 600bending length: 6050column width: 5100daylight: 680stroke lenght (max.): 455column throat depth: 450messurements (LxWxH): 7100x3275x3910weight approx.: 50.2004 axes (Y1, Y2, X, R): Ja alle Achsen über die Esa S630 (2D Grafik Steuerung)CNC crowning system by control: ja über die Esa S630 (2D Grafik Steuerung)motor power: 45Standard Equipment:KK Kletzer Europa We have developed a high-quality model specifically for the European market:The CNC press brake by KK Industries, made in Turkey. Model: KK Kletzer EUROPA XL The powerful EUROPA XL press brake stands out for its high precision, accuracy, and versatile offers a very large open height, resulting in a long cylinder stroke, and an extra-large throat depth to provide maximum flexibility during operations. We focus on delivering quality—reflected also in the control system:As standard, the machine comes equipped with the ESA S640 2D graphic controller. Additionally, the KKI EUROPA XL is equipped with CNC-controlled Y1, Y2, X, and R axes via the wning is also included and fully CNC-controlled through the same ESA S640. When it comes to tooling, we make no machine is fitted with premium top tools and dies from EUROSTAMP Italy. Naturally, a machine is only as good as the service behind t’s why we rely on highly qualified staff with many years of experience in CNC sheet metal processing. Nlsdpsd Ehh Refx Ah Usk Technical Highlights: CNC axes: Y1, Y2, X, and R Controller: ESA S640 (2D graphical interface) Backgauge with double linear guides and ballscrews Motorized CNC-controlled crowning system Heavy-duty height adjustment with handwheel(from 175 tons: on linear guides) Laser safety system on the upper beam CE-compliant safety equipment Various options available Optional Controllers: ESA S640 – 15” 2D Touchscreen: ¤ 4,520.00 ESA 675 W – 21” 3D Touchscreen (Windows-based): ¤ 6,485.00 DELEM DA-66T – 17” 2D Touchscreen (Windows-based): ¤ 10,165.00 DELEM DA-69T – 17” 3D Touchscreen (Windows-based): ¤ 16,350.00

Year of construction: 2003, condition: used, pressure 100 t stroke 10-130 mm no. of strokes 30-90 Hub/min throat 330 mm ram - range of adjustment 100 mm table surface area 950x660 mm ram surface 540x440 mm hole in the table Ø 230 mm table height 1000 mm Nodpfx Ahora Rr Eo Uelk tool hole in ram Ø 50 mm total power requirement 7,5 kW weight of the machine ca. 7 t

Year of construction: 1980, condition: used, pressure 80 t throat - mm stroke 50 mm table surface area 875 x 695 mm ram surface 350 x 355 mm ram adjustment 71 mm no. of strokes 30 - 90 Hub/min distance between columns 450 mm weight of the machine ca. 6,2 t dimensions of the machine ca. 2,0 x 2,1 x 3,2 m daylight (stroke down, ram adjustment above) 480 mm Further information: - the machine is currently being a partially overhauled - the machine was re-equipped with the following components: * separate control cabinet with touchscreen including cabling * new painting of the individual components in the dismantled state After the partial overhaul, the machine is safe for manual insertion open tool, a current UVV test is carried out before delivery and Nlsdpedlcy Hjfx Ah Ujk braking time measurement.

Condition: used, Double column eccentric punching press BLEMA Gotha type PEZ 160-50 MHSY-ES Eccentric press with roller feed ALBA Machine no. No. 88151005 Year of construction 1988 / 92 Pressure force 160 ton. Frame width 970 mm Stand width sideways 560 mm Table size 900 x 900 mm ram surface 900 x 700 mm Tool installation height 560 mm, max. 700 mm Stroke adjustment 8-160 mm Ram adjustment travel 125 mm Stroke rate 25 to 70 strokes/min. Belt width in roller feed max. 400 mm Motor power approx. 15 kW Mains connection 380 Volt, 50 Hz - Infinitely variable stroke rate via frequency control - Automatic stroke adjustment - ram weight compensation cylinder with compressed air - Hydraulic overload protection in the ram - Pneumatic clutch/brake combination - Central oil lubrication - Precisely guided press ram with oil-lubricated guides - UNIDOR press control - Swiveling control panel - Press and feed control cabinets, together on one platform, adjacent Platform dimensions 3400 x 2250 mm, height without feet 2950 mm Nlodpfxjdzqlvs Ah Uek Width of the press without feed 2100 mm Depth of the press with drive motor 2300 mm Overall height of the press 4150 mm Weight of punching press approx. 18 tons. For transportation, the drive motor is removed and the machine is placed on its face. In addition: NC roll feed straightening machine ALBA type GGVHY400 Apparatus no. 1405 and 1406, order no. 910708 (year of manufacture 1992) - ALBA PSS 300 feed control - Feed length infinitely programmable from 0.1 to 6500 mm per stroke - Belt thickness at 400 mm width max. 3 mm - Belt thickness for 300 mm width max. 4 mm - Belt cross-section max. 1200 mm2 - Roller drive hydraulically controlled by the feed - Height-adjustable feed unit on the press to adjust the material infeed height - Hydraulic unit opposite - Drag straightener with hydraulic opening and closing Weight of the complete system approx. 24 tons Space required for transport a mega trailer with an internal height of 3 meters and a loading length of 13.6 meters good condition

Year of construction: 2021, condition: new, Cantilever rack, one-sided, 3.70m height, 1.20m arms, 500kg per arm - new -: Price ex location including loading! Nlsdsf Tv T Njpfx Ah Ujk 1 shelf unit with 4 stands € 2.255 (net)! Price for transport within Germany (excluding islands): € 490 (net)! Of course, you can also build longer or shorter shelving units from them by omitting or buying additional frames (or by using different center distances), this example with 4 frames is only the most common shelving solution! A cantilever racking system, hot-dip galvanized, consisting of: Arms: IPE 80 Frame: IPE 180 Shelf stand on one side approx. 3,700mm high, hot-dip galvanized Leg and arm depth 1200 mm with 3 height-adjustable shelf arms each Load capacity at a load center of 600 mm 500 kg per arm / 2,700 kg per stand with 4 stands per arm level 4 x 500 kg = 2,000 kg with longitudinal and diagonal bracing e = 1300 mm, the standard is 1.30 m - so if you do not have any deviating information, we will deliver the rack with a center distance of 1.30 m. Other center distances possible e.g. 1m, 1.25m for a small surcharge also 1.50m or special dimensions! As a standard delivery, the length of a row of shelves with 4 uprights is approx. 4000 mm. Delivery with all screws and nuts, without ground anchors. Other configurations (frame height, arm lengths, arm types etc.) can be selected! Please contact us!