GUILOTINE SHEAR

ECLAIR NSH 20

Year of construction: 2008, condition: ready for operation (used), X-axis: 2500mm, Y-axis: 1270mm, positioning speed X-axis/Y-axis: 80/90m/min, simultaneous axis speed: 100m/min, punching capacity: 200kN, number of turret stations: 51, max. material thickness mild steel: 3.2mm, max. material weight at traverse speed F1/F4: 50/150kg, positioning accuracy: ±0.1mm, stroke rate X-axis: 350/min, stroke rate Y-axis: 260/min, max. stroke length: 42mm, max. feed speed X-axis/Y-axis: 80/60m/min, turret speed: 30rpm, compressed air requirement: 500l/min, operating air pressure: 5bar, connected load: 19kVA, length: 4165mm, width: 5120mm, height: 2082mm, height with mirror: 3028mm, weight: 13t, operating hours: 4531h, regularly maintained by the manufacturer, with documentation, without punching tools. An on-site inspection is possible. Pjdpfxeza E S Dj Abuerc

Condition: used, Table unit from a DROOP & REIN portal milling machine Clamping plate with T-slots made of steel cast gray iron Predpothuzpefx Abuoc Table unit with clamping plate and very robust guide rail Table clamping surface: 5500 x 2000 mm Travel of the table clamping plate: approx. 3100 mm Table height / overall height: 1050 mm Table load: max. 20 tons Ball screw: Ø 100 mm Thread pitch: 20 mm (single start) - Machining table guided very stably on the bed - Metal telescopic guide rail cover - from a DROOP & REIN portal milling machine - Table longitudinal movement via ball screw and SIEMENS servo motor - Clamping surface with 11 T-slots, 28 mm - Drive via SIEMENS servo motor 1FT6134-6AB71-1AG2 with encoder IC200448S/R (RN 000 B25) Overall length: 9500 mm Width: 2000 mm Overall height: 1050 mm Weight: 27 tons Good condition

Condition: used, pressure 160 t passage width / mm stroke / mm Pedpfoiulkqox Abuerc Working height 800 mm total power requirement 15 kW weight of the machine ca. 11,8 t - Table size: 1000x1000mm - Distance table/ram, large stroke above, gain. above: 800mm extra information Removable table

Condition: used, 72″ x .187″ x 50,000Lb Paxson Loop Slitting Line Make: Paxson Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Entry Transfer Cart Prjdpfx Abeihf Ufeuoc Entry Coil Car Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Hydraulic Peeling Table Driven Pinch Rolls

Condition: good (used), Year of construction: 2007, control 840 D x-axis 2500 mm y-axis 2500 mm z-axis 1700 mm Control system - Siemens Sinumerik 840 D Max. workpiece weight - 6000 kg Spindle diameter - 130 mm Quill stroke - 700 mm Tool holder - ISO 50 DIN 69871 - AD Predjwzyp Uopfx Abujc Max. torque at the spindle - 1847 Nm Total power requirement - 65 kW Machine weight approx. 45 t Space requirement approx. 10.9 x 9.3 x 5.7 m

Condition: ready for operation (used), Selling a well-maintained Mikron VC 1000 milling machine due to the purchase of a new machine. Psdpfxeh Tnpxj Abuerc

Year of construction: 1985, condition: reconditioned (used), Technical Details : Prjdpeh In Thofx Abujc Wire Dimeter range- 4-12mm Gscxckebw Run out table - 4m Speed -80' m/min. Reconstruction- 2022

Condition: good (used), functionality: fully functional, Year of construction: 1998, control type: NC control, degree of automation: semi-automatic, actuation type: hydraulic, controller manufacturer: Siemens, controller model: Simatic OP7, number of rollers: 4, roller (bottom) diameter: 470 mm, roller (top) diameter: 530 mm, side roll diameter: 400 mm, roller diameter: 530 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 2,000 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 65 mm, sheet thickness stainless steel (max.): 50 mm, overall weight: 40,000 kg, total length: 6,000 mm, total width: 2,900 mm, total height: 2,900 mm, power: 55 kW (74.78 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 4, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, plate bending roll capacity 3000x50 mm Davi modelMCB3053 Hydraulic 4 roll plate bending machine, year 1998 plate width 3000 mm thickness rolling 50 mm pre-bending 40 mm width on the rolls 3100 mm upper roll size 530 mm lower roll 470 mm side rolls 400 mm Power electric 70Hp on hydraulic unit voltage 380/50 - Installed configuration Hardened surface of the 4 rolls Prjdpfsy D Ngzex Abusc conical bending attachment – hardened cone bending Console electric with digital position readout of the rolls Controller Siemens Simatic OP7 NC programmer for automatic rolling Hydraulic power driven the central rolls with axial gearbox Pre-pinch pressure adjustable plate edge pre-bend. Drop-end open front for unloading closed shells Rerolling system for calibration roundness of welded shells. Safety and emergency system installed. Manuals original for operation and maintenance Dimension 6000x2900 x h 2900 mm weight 40000 kg

Condition: excellent (used), Year of construction: 1985, functionality: fully functional, pressing force: 4,000 t, 5. Forging hammer SMERAL type KJH 4 Weight of the ram, kg: 1’800 Ram impact rated energy, kgm: 4’000 Number of ram strokes,1/min: 48 Ram stroke, mm: 500 Die camping area, mm: 286 x 600 Min. Die Height, mm: 350 Output of main motor, kW: 45 Lenght of the machine, mm: 3’100 Podswbginjpfx Abuerc Widht of the machine, mm: 1’900 Height of the machine, mm: 3’900 Weight of the machine, kg: 27’000

Condition: good (used), Year of construction: 1984, max. wheel diameter 250 mm gear width 275 mm max. module 6 Pjdev T Nqaepfx Abuorc weight of the machine ca. 5,5 t The gear hobbing machine ZFWZ 250 is suitable for the economical production of all hob-processable cylindrical gear types, such a: - spur and helical gear, wormgears and worms, splined shafts, keyed shafts, serrated profiles, chain wheels and ratchet wheels,as well as conical and crowned spur and helical gears. Interchangeable wheels and milling accessories Technical data: - Workpiece diameter (max): 250 mm - Module (max): 6 mm - Axial feed travel (max): 275 mm - Tangential feed travel (max): 100 mm - Tooth helix angle (max): 45 degrees - Milling cutter diameter (max): 145 mm - Milling cutter length (max): 170 mm - Table clamping surface (min): 195 mm - Table clamping surface (max): 470 mm Power Milling cutter speeds - Stepped in 2 ranges: 56 ... 250 rpm - (Standard version): 90 ... 400 rpm - Infinitely variable in 2 ranges: 63 ... 180 rpm - (special version DC motor): 140 ... 400 rpm Weights - Machine net: approx. 5000 kg - Electrical cabinet: approx. 800 kg - Hydraulic unit + coolant tank + chip transport: approx. 700 kg Overall dimensions (with oil mist filter) - Length: Standard version: 3950 mm DC drive: 3450 mm (or 3350 mm according to table) - Width: 3300 mm - Height: Machine: 1980 mm Machine with DC drive: 2150 mm Electrical cabinet: 2200 mm