Four rolls Bending roll 3000 x 70 mm

FACCIN 4HEP 3163

Condition: good (used), total width: 3,500 mm, total length: 19,000 mm, total height: 2,100 mm, workpiece weight (max.): 6,000 kg, grinding diameter: 850 mm, grinding length: 6,000 mm, center height: 425 mm, Cylindrical grinder Schmaltz - RM 82/6000 MACH-ID 9492 Make: Schmaltz Type: RM 82/6000 Centre height: 425mm Grinding Ø: 850mm Grinding length: 6000mm Grinding stone dimensions:1100 x 80 x 560mm Grinding stone speeds: 700Rpm Table inclasement: -5 to +5° Psdpfx Ajy Dr Easm Tjgp Tailstock: 160 x 100Mk Length: 19000mm Width: 3500mm Height: 2100mm Weight: 31000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, Year of construction: 2025, tube diameter 48,3 mm wall strength 3,25 mm bending radius min. max. 180 mm Bending speed 20 °/sec total power requirement 2,4 kW weight of the machine ca. 700 t dimensions of the machine ca. 3880 x 800 x 1250 m Description: Round tube steel (S235): 60.0 x 6.0 mm Round tube stainless steel (S 355): 60.0 x 4.0 mm Square tube steel: 50 x 50 x 4.0 mm Pedpfxoxcuico Am Tjgp Rectangular tube steel: 60 x 40 x 2.0 mm max. usable length: 3048 mm Bending speed: 10°/sec including tools (see photos) Mandrel is no longer available, can be retrofitted

Condition: excellent (used), Motorized 3x3 welding column with movement control by pushbutton panel. Useful capacity: 3x3m Wire spool dispenser Pgjdpfxju Aftto Am Tsp Lincoln Idealarc DC-1000 submerged arc equipment with torch and flux holder + Lincoln NA-3N Amps and Volts regulation panel. Submerged arc duty factor: 1000 Amps at 100%. Idealarc® DC-1000 Submerged Arc Welder Input voltage: 230/460 Input current: 193/96.5A Input Hertz: 60 Input phase: 3 Input power: 230/460/3/60 Mode icon: DC/DC Output range: 150-1300A DC,16-46V Polarity: DC Nominal output: 1000A/44V/100%

Condition: ready for operation (used), Year of construction: 1970, Gear hobber ZFWZ 6300x40 Manufacturer: WMW-MODUL Model: ZFWZ 6300x40/1 Pgsdpfx Aexln Iwjm Tsp Year of manufacture: 1970 Max. workpiece diameter: 7100 mm Gear width: 1500 mm Max. module: 45 Table diameter: 5300 mm Cutter diameter x width: 400x500 mm Max. helical angle: 45 degrees Hob diameter: 500 mm Hob speeds: 9–63 rpm Total power requirement: 47 kW Machine weight: 160 tons Equipped with standard hobbing head, tangential hobbing head, internal milling head, change gears, supports. Video available.

Condition: used, travel distance X-axis: 7,000 mm, travel distance Y-axis: 4,000 mm, travel distance Z-axis: 900 mm, spindle speed (max.): 1,200 rpm, feed rate X-axis: 900 m/min, Ø quill: mm. 140 Spindle taper : ISO 50 travel X : mm. 7000 Pgjdpfx Amst Rkcuo Top travel Y: mm. 4000 Cross travel Z RAM: mm. 900 Quill travel W: mm. 900 Rotary table: mm. 1800x1800 load admitted on table: Ton. 10 Table rotation: °.pos. Table long.travel (AxisV): mm. 1500 Spindle speed : RPM. 1200 Spindle motor: Kw. 70 CNC ECS 2101 N°2 milling square heads N.2 Floor plate 6000x2000

Condition: used, Radial drilling machine CSEPEL, Type RFh 75 / 1500 Machine no. 13704, Year of manufacture 1985 Drilling capacity in steel: Ø 75 mm Drilling capacity in cast iron: Ø 90 mm Spindle mount: MK 5 Nominal overhang: 1500 mm Maximum overhang of the spindle: 1500 mm (to the column) Minimum overhang of the spindle: 440 mm (to the column) Distance from spindle nose to clamping surface: 370 - 1700 mm Overarm vertical adjustment: 950 mm Table size / clamping surface: 1800 x 1100 mm Column diameter: 450 mm Quill stroke: 380 mm Spindle speed: 19-1900 rpm, 21 steps Feed rate: 0.047-2 mm/rev, 12 steps Motor power: 11 kW Mains connection: 380 Volts, 50 Hz, 15 kW - Right-hand and left-hand rotation of the drilling spindle via hand lever switch - Hydraulic gear change for spindle speed and feed rate - Hydro-mechanical central clamping device - Motorized overarm vertical adjustment - Without coolant system - Machine light - Operating manual Space required: Length 2720 mm x Width 1170 mm x Height max. 3770 mm Transport height with motor on the column: 3500 mm Transport height without motor on the column: 3250 mm Pjdpjlhwr Refx Am Tjgp Weight: 6.3 tons Good condition

Year of construction: 2007, condition: used, gear hobbing diameter - external 1200 mm gear hobbing diameter - internal 1200 mm gear hobbing width -max. 260 mm control Liebherr PC-NC max. workpiece diameter 1500 mm table diameter 900 mm table bore diameter 320 mm max. table load 95 kN power capacity 30 kW coolant pump 120 l/min Axial distance between thrust spindle - table 0-820 mm Shaping spindle diameter 125 mm tool taper SK 45 DIN weight of the machine ca. 26 t dimensions of the machine ca. 8,073 x 6,183 x 4,375 m Strokes: - Stroke length min./max. - 0 mm / 270 mm - Stroke length adjustability - 270 mm - Stroke rate (double strokes) - 10 to 270 DH/min Equipment/accessories: - Chip conveyor - Cutting wheel holder SK 45 DIN - Cooler Podpfxjw Rf S Ee Am Togp - Technical documentation

Condition: used, Year of construction: 1983, grinding length 8400 mm grinding width 1450 mm workpiece height 1250 mm surface area 8000 x 1250 mm table height over floor 920 mm Pgodpfx Ajvr Hgvom Tjp distance between columns 1470 mm workpiece weight max. 59700 kg weight of the machine ca. 59,7 t dimensions of the machine ca. 22 x 5 x 5 m Adjustment ranges: -Crossbeam, vertical 1250 mm -Grinding support, horizontal 3100 mm Adjustment speeds: -Machine table (X-axis) infinitely variable 1-45 m/min Table creep speed 5 m/min -Grinding support, horizontal (Y-axis) Rapid traverse 3000 mm/min Feed, step 0.001-0.099 mm Feed rate, continuous 100-3000 mm/min Creep speed 18+1 mm/min Tip infeed 0.001-0.019 mm -Crossbeam (W-axis) Rapid traverse 410 mm/min Table drive: -Oil transmission, Type Iv4 -Cylinder-Ø 185 mm -Piston rod Ø 130 mm -Drive motor 22 kW

Condition: used, Technical Data Faceplate diameter: 1580 mm Pedpfx Aswyn Ntom Tsgp Max. turning diameter: 1700 mm Max. turning height (cross rail support): 1250 mm Max. turning height (side support): 1160 mm Max. faceplate load: 12,000 kg Max. distance from faceplate to underside of cross rail: 1210 mm Max. distance from faceplate to underside of side toolholder: 980 mm Max. distance from faceplate to underside of turret head: 1420 mm 18 spindle speeds: 2.8 – 140 rpm 18 feed rates: 0.063 – 3.15 mm/rev Total power requirement: 55 kW Required floor space approx.: 5300 x 3500 x 4100 mm Control: conventional

Condition: excellent (used), Year of construction: 1987, pressure 320 t plate thickness 0 mm no. of strokes 80 Hub/min Pgodpfx Aevwgl Nsm Tep pressing capacity total 320 t stroke 30 - 80 mm table surface area unten: 630 x 740 mm table surface area oben: 630 x 630 mm total power requirement 60 kW This fineblanking press FEINTOOL HFA 320 was completely overhauled in 2019 and is in new condition with new CE mark MAIN RAM total force (nominal) 320 to stroke min. 30 mm stroke 80 mm V-RING nominal force 160 to stroke 30 mm COUNTER RAM nominal force 80 to stroke 30 mm TOOL DIMENSIONS lower table - width 630 mm lower table - depth 740 mm upper table - width 630 mm upper table - depth 630 mm daylight max. 320 mm ELECTRICAL SPECIFICATIONS total power consumption 60 kW