Condenser

Güntner GVH 090.2A/2x5-N(D)

Condition: good (used), Auriol M500VBEX cooking kettle Serial: 3429 Stainless, 500l capacity, steam jacketed, emulsifier with bottom mounted motor, emulsifier diameter 120mm, variable speed, auto tilt to discharge, on load cells, 3Ph Fsdpfx Aenbd S Tohpepi

Condition: excellent (used), Year of construction: 2004, functionality: fully functional, cooling capacity: 680 kW (924.54 HP), Equipment: cooling unit, condenser Manufacturer: Güntner GVH 090.1.D/5-M(D) Year of manufacture:2004 Nominal power 680.4 /579.2 kw Refrigerant:R404 Refrigerant content:218.9+25 liters Flow rate: Temperature range: -50°C- +100°C Max pressure: Operating pressure: 28bar/-1bar (performance depends on usage parameters) Number of fans: 5 pcs, diameter 900 mm, Air flow:162500 /131000 m3/h Motor power consumption:17.60/11.50 Kw Heat exchanger aream2 Operating noise 52 dB Length: mm Height: mm Width: mm Weight: ca kg Fpjdpsvllxdjfx Ahpei The radiator has been technically inspected, fully functional

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: ELB0109, cooling capacity: 720 kW (978.93 HP), type of input current: three-phase, type of cooling: air, overall weight: 4,500 kg, ambient temperature (max.): 46 °C, ambient temperature (min.): -10 °C, input voltage: 400 V, pressure: 15 bar, volume flow: 65 m³/h, total width: 406,000 mm, total length: 225,000 mm, total height: 247,000 mm, noise level: 72 dB, input frequency: 50 Hz, Trane Air-Cooled Chiller GVUF205 X XLN – 2018 Manufacturer: Trane (France) Model: GVAF 205 X XLN Year of Manufacture: 2018 Serial Number: ELB0109 Type of Cooling: Air-cooled (screw chiller) Cooling Capacity: ~720 kW, 620kcal/h Refrigerant: R134a (2 independent circuits – 75/70 kg, GWP 1430) Power Supply: 400 V / 50 Hz / 3-phase Maximum Current (A max): 506 A Starting Current: 596 A Short-Circuit Protection (ICC-LRA): 35 kA Design Pressure: Refrigerant circuit: LP 15 bar / HP 18.8 bar Water side: 10 bar Operating Conditions: Ambient Temperature Range: –10 °C … +46 °C (optional Low Ambient Kit: up to –25 °C) Water Flow Rate: ~65 – 108 m³/h Evaporator water content: ~120 L Dimensions & Weight: Overall Weight: 4 414 kg Dimensions (L × W × H): 4 060 × 2 250 × 2 470 mm Key Features: High-efficiency air-cooled screw chiller. Two independent refrigerant circuits ensure reliability. Uses R134a refrigerant, environmentally compliant. Extra-Low-Noise (XLN) version – optimized for reduced sound emissions. Fpodpfx Aew R Ualehpsi Suitable for industrial and commercial cooling applications. Condition: ✔️ Good working condition ✔️ Regularly maintained ✔️ Immediately available

Condition: new, Year of construction: 2025, functionality: fully functional, turning height: 1,400 mm, workpiece weight (max.): 8,000 kg, turning diameter: 1,600 mm, faceplate diameter: 1,250 mm, total height: 5,190 mm, total width: 4,875 mm, total length: 3,885 mm, rotational speed (max.): 360 rpm, torque: 17,880 Nm, table load: 8,000 kg, overall weight: 30,000 kg, Equipment: rotational speed infinitely variable, Vertical turret lathe in flat-guided design with extensive full equipment: WITH MILLING FUNCTION - Milling spindle 2000rpm SK50 22 KW - C - axis 0.001 degrees - Complete housing - Chip conveyor - Internal coolant supply - Fanuc control - 24 tools - 12 milling tools - Manual Guide I - Tool holder package Fpedpfsvtzc Iex Ahpei - Electronic handwheel - Signal light - Manual 3-jaw faceplate 1250mm - Renishaw tool measurement - Renishaw workpiece measurement - Glass scales in X and Z axes - 24 month guarantee

Year of construction: 2016, condition: as good as new (ex-display), Axial fan condenser, air ccoler Manufacturer: Güntner Model: GCVC RD 035.1/12-42-0007305P Year of c.: 2016 2 fans Volume: 4,6 l Fjdpfxonbff Ae Ahpopi Comressed air: 32,5 bar

Condition: good (used), Auriol cooking kettle Stainless, 400l capacity, steam jacketed, emulsifier with bottom mounted motor, emulsifier diameter 120mm, variable speed, auto tilt to discharge, on load cells, 3Ph Fpodpfonbd Rysx Ahpoi

Condition: new, functionality: fully functional, machine/vehicle number: 8153336470, overall weight: 616 kg, volume flow: 399 m³/h, pressure (min.): 4 bar, pressure (max.): 13 bar, noise level: 67 dB, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, We are a company specializing in the compressed air industry for over 20 years. Professional level of service and high quality goods offered by our company - "proven" on the market - guarantee successful cooperation with you. We offer NEW screw compressor Atlas Copco GA37VSDs FF (variable speed with built-in dryer) Machine equipped with frequency converter (inverter), manufactured based on the latest technologies, which translates into greater efficiency and performance: On average 20% lower unit energy consumption (SER) than in previous models of the GA VSD series. Ecological and efficient VSD+ variable speed drive system reduces energy consumption by an average of 50% compared to models that operate at idle speed. Regardless of energy savings, efficiency (FAD) increases by up to 12%. Efficient fan motor (compliant with the ERP 2015 directive) reduces energy consumption and noise level. Superior Motor Efficiency (iPM) up to 94.5% exceeding IE3 efficiency levels. Built to work hard for your success. The industry-leading GA Series oil-injected rotary screw compressor delivers unmatched efficiency, high productivity and low cost of ownership – even in the harshest conditions. Technical data: capacity at 4 bar: 15.69- 13.75 l/s / 0.94-7.85 m3/min capacity at 7 bar: 15.67-129.35 l/s / 0.94-7.76 m3/min capacity at 10 bar: 15.68-110.79 l/s / 0.94-6.65 m3/min Max pressure 10 bar (13 Bar variant on request) Voltage 400 V Motor 37 kW Noise 67 dB(A) Weight 616 kg Motor with internal permanent magnets (IPM) Compression element Fpsdpfswlp Hdjx Ahpei Direct drive Innovative fan Separator/oil filter with durable construction Electronic water drain valve that does not cause compressed air losses Controller Elektronikon Inlet valve VSDs module Manufacturer code: 8153336470 If you are not sure whether the device is right for you, you have not found the right compressor, CALL! We will advise you on the right choice of device. We invite you to familiarize yourself with our full offer.

Condition: used, Year of construction: 1991, pressure 400 t stroke 300 mm table surface area 1200 x 700 mm ram surface 1200 x 700 mm dayligth 500 mm adjustment of stroke 300 mm return capacity 348 kN capacity of ejector 100 kN ejector stroke 100 mm control SIEMENS Simatic S 5 total power requirement 65 kW weight of the machine ca. 28 t dimensions of machine L x W x H 4,4 x 2,75 x 4,0 m = hydr. punching and embossing press Accessories: tool changing table Fjdpfx Astqqlcshpopi - with cutting shock absorption damping force 4000 kN damping stroke 5 mm spindle adjustment 200 m

Condition: like new (used), Year of construction: 2018, Complete Aerzen D17L and D28L units are for sale. Manufactured in 2018, they are in excellent condition and equipped with 15 kW and 22 kW motors. Warranty included. For more information, please contact me by phone or email. Fpjdpfx Ahjlnlr Eopji

Condition: new, Year of construction: 2025, functionality: fully functional, turning height: 1,600 mm, turning diameter: 2,000 mm, CNC Vertical Turning Center Model: VTC-16/20R with Fanuc 31i-B Table Diameter: Ø1,600 mm Max. Swing Diameter: Ø2,000 mm Max. Turning Height: 1,600 mm Table Speed: Max. 250 rpm Table Load Capacity: 8,000 kg Table Indexing Speed: 720°/min Table Indexing Accuracy: 0.001° X-Axis (Ram horizontal): -100 mm to 1,170 mm Z-Axis (Ram vertical): 900 mm Drive Spindle Speed: Max. 2,000 rpm Ram Size: 240 mm x 240 mm Milling Spindle Taper: ISO 50 Tool Shank Size: 40 mm x 40 mm Crossrail (vertical travel): 250 mm x 3 stages (hydraulic) Table Drive Motor: AC 37/45 kW (continuous/30 min. duty) Milling Spindle Drive Power ISO 50: 15/18.5 kW (continuous/30 min. duty) Control System: Fanuc 31i-B Display Unit: 15-inch TFT-LCD Fedpfsxp Nb Tjx Ahpepi Memory Capacity: 1 MB Automatic Tool Changer: 24 positions (for 7 turning tools + 1 cover + 16 milling tools) Standard Tool Holders: New 240 TCR-01 (2 pcs) Splash Guard: Table version (R-Type standard design) External Coolant System: 3 bar (80 l/min) Chip Conveyor: Hinged belt type Table Bearing Cooling Device 4-Jaw Independent Manual Chuck Foundation Anchor Bolts / Base Plates Maintenance Tools and Toolbox Hydraulic Power Unit Work Area Lighting Signal Lamp: 3 colors (green, red, yellow) Operating Manuals (English): 1 CD with Fanuc manuals and 3 books with mechanical/electrical manuals Power Supply: 220 V, 60 Hz, 3-phase Machine Color: Manufacturer standard OPTIONAL ACCESSORIES (#1) Turning Tool Holder: Type 240TCR, 4x included Rigid Tapping: 1x included OPTIONAL ACCESSORIES (#2) Automatic power-off for N.C. - on request Turning tool holder type 240TCR - on request Through-spindle coolant supply: 30 bar (pump pressure) - on request Transformer 415 V, 50 Hz, 3-phase - on request Linear scales X-, Z-axis (Fagor, Spain) - on request Workpiece measuring device - on request Tool measurement TS27R, Renishaw - on request Other information: INSTALLATION, COMMISSIONING, TEST OPERATION, AND TRAINING - not included in the price INSURANCE AND FREIGHT - not included in the price Image shows machine with pallet changer. The offered machine DOES NOT INCLUDE A PALLET CHANGER! Errors in technical data excepted. The scope of accessories is as described in the text of this article only. There is no entitlement to any other accessories, such as those shown for illustration purposes. The general terms and conditions of JS-Werkzeugmaschinen GmbH apply.