Band saw

GEORGE CY270N

Condition: new, capacity 90 degrees: round 240 mm capacity 90 degrees: square 240 mm 165 x 310 mm saw band length 2725 x 27 x 0,9 mm mm table height 890 mm band speed 35 / 70 m/min total power requirement 1,1 kW weight of the machine ca. 0,35 t Dimensions (LxWxH) 1,7 x 0,75 x 1,8 m The Z252/DG has the following equipment: - hydraulic cylinder, - emulsion pump, - eccentric clamp, - base, - saw blade, Iiedpfxohpktvo Apneb - 400V plug -16A- The machine is delivered fully assembled and ready for immediate use.

Condition: new, Year of construction: 2026, CORMAK HBS275 band saw, equipped with a hydraulic cylinder, a cooling system and an arm swivelling up to 60º, together with blades from renowned German company Röntgen, is used commonly in ironworking, where precision, quality and cutting speed are essential. Horizontal band saw with a swivelling arm for cutting metals, allows for cutting in plane perpendicular to the axis of material cut and at any angle from 0 to 60º. Material for cutting can be fed manually or with any mechanical feeding device, with automatic tool feed. Band guides are equipped with dedicated carbide plates and bearings. This has a huge impact on band guiding, its durability, cut straightness, cutting accuracy and quality. Carbide guiding drastically reduces the wear of the machine and blades. Machine's arm made of uniform cast iron as well as a 27 mm wide cutting band are capable of low and high quantity cutting of profiles and other materials. The vice is located in an adjustable bed, equipped with a quick clamp. Blade guides have cemented carbide plates and roller bearings. Its these cemented carbide guides that provide cut precision and straightness. The arm, positioned at an angle of 25º, thus increasing blade durability. To the bottom of the arm a brush wire is attached, ensuring clean and functional brush. Machine's drive is transmitted through a worm drive. A 3-phase motor with 2 cutting speeds and motor thermal protection. This cutting machine also has a strain gauge - a band tension sensor and an automatic switch-off in case the cutting band breaks. Upper part of the base constitutes a tank for flood coolant draining and chips produced during cutting. A cast iron workbench is attached to the base, with a swivel arm and control panel on separate arm. The main cutting move in the cutting process is moving the cutting band and the arm lowering feed. The arm lowering speed (the cutting speed) is adjusted with the hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds to choose from: 37.5 and 75 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Total power 1.5 kW Power supply 400V 50Hz Arm lowering control hydraulic cylinder Band dimensions 2455 x 27 x 0.9 mm Iodpfsudi Unjx Apnjib Band speed 37.5/75 m/min Vice base height 900 mm Weight 215 kg Angle 0º ø220 260 x 140 200 x 200 45º R ø160 160 x 140 160 x 160 60º R ø100 120 x 100 100 x 100

Condition: new, Year of construction: 2026, The CORMAK HBS260 band saw for cutting pipes, profiles and bars is widely used in all locksmith workshops where precision, quality and cutting speed are important. The model is equipped with a 0-60° swiveling arm. The frame design ensures accurate and quiet operation. It has a removable filing tray for easy cleaning! Machine characteristics A horizontal metal band cutter with a swiveling arm allows cutting in a plane perpendicular to the axis of the material being cut and at any angle ranging from 0 to 60°. The material to be cut can be fed manually or with any mechanical device, and the tool feed is automatic. The tape guides are equipped with special carbide plates and bearings. This has a huge impact on the belt guidance, its life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and saw blade. The machine is equipped with an efficient cooling pump with a closed coolant circuit. The cutter's arm made of uniform cast iron together with the 27 mm wide cutting band used in this cutter allows it to fully perform multi-series cuts of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The saw blade guides are equipped with hard metal plates - sintered carbides and a rolling bearing system. It is the CENTRED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The shape of the upper part of the base constitutes a bathtub for draining coolant and catching chips generated while cutting the material. A cast iron work table with a swivel arm and a control panel on a separate arm is attached to the base. In the cutting process, the main cutting movement is the movement of the cutting band and the falling feed of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic actuator. The feed speed is regulated on the cutter's control panel. We can choose from two cutting band speeds: 35 and 70 m/min. In the lower position of the arm (after cutting the material), the cutting belt drive is turned off automatically. Safety is ensured by the cutting band covers and micro switches that stop the engine after the cutting cycle is completed or any of the covers are opened. Additional protection consists in automatic shutdown of the cutter in the event of the cutting band breaking. Cutting band size [mm] 2520 x 27 x 0.9 Tape tension mechanical (manual) Belt speeds [m/min] 35, 70 Adjustable arm drop stepless - hydraulic actuator Vice base height [mm] 860 Saw wheel diameter [mm] 300 Saw frame tilt [°] 0-60 Power supply 3 phases 400V Main engine power [kW] 1.1/1.5 Cooling pump motor power [kW] 0.05 Dimensions with base [cm] 150x80x140 Weight [kg] gross/net - 210 / 180 kg Additionally 2 M42 saw blades Iedpfx Asudi Uzopneib 5L Emulsol ZW580 magnetic chip collector

Condition: new, capacity 90 degrees: round 255 mm capacity 90 degrees: square 240 mm 300 x 180 saw band length 2.765 x 27 x 0,9 mm mm table height 950 mm band speed 35 + 70 m/min total power requirement 1,5/1,8 kW weight of the machine ca. 0,42 t dimensions of the machine ca. 1,23 x 1,7 x 1,75 m Iodeurc S Ropfx Apneib Double miter metal band saw, GBS 250 Super AutoCut (20413) - Miter cuts up to 60° left and 45° right - Ball bearing rotary table Quick clamping device Solid, large material support Automatic cooling

Condition: new, Year of construction: 2026, Powerful, reliable and modern semi-automatic band saw for metal with automatic arm raising and lowering. The arm is rotational in both ways. The machine is fantastic for ironworking, e.g. cutting tubes and profiles. Product features CORMAK S-200RH band saw is by default equipped with automatic arm lowering and raising as well as with a precise arm height regulator. Due to an automatic hydraulic damper, the manual handling of the machine has been simplified to feed and clamping the cut material in a vice. The arm made of uniform iron casting, together with a refined, solid and stable construction, ensure S-200R's exceptional rigidity, resulting in failure-free handling and high cutting precision. The innovativeness and production of semi-automatic and automatic series "CORMAK-PREMIUM LINE" band saws, compliant with the norms and standards consistent with ISO:910001 and ISO:140001 certificates, warrant safety, quality and reliability of the product. M3V motors from ABB, a renowned worldwide manufacturer, warrant long-term reliability. As an official and the only representative on the Polish market, we assure that the product is original and provide professional, customised warranty and post-warranty services. Technical data Type - semi-automatic Arm raising and lowering - hydraulic with smooth arm lowering control Band speed - 36/70 mm/min Angled cutting - left to 45°, right to 60° Vice - hydraulic Minimum cutting diameter - Ø 5 mm Minimum material length in vice - 30 mm Vice base height - 780 mm Cutting band dimensions - 27×0.9×2910 mm Total power - 2.1 kW Dimensions (LxWxH) - 1600×800×1400 mm Weight - 530 kg Angle 0º -----ø250 320×240 240×240 45º L ø200 220×120 190×190 45º P ø220 235×120 210×210 Ijdpfxsi D D A Se Apnoib 60º P ø110 155×110 100×100 Default equipment Control panel on separate component Built-in hydraulic unit Hydraulic control of arm motion (up – down) with possibility of smooth lowering speed control Arm position memory function (arm returns to a defined height after cutting) Cutting at angles of L/R 45° - 0° - 45° - 60° Brush for cleaning band Cooling system Bi-metal band saw EC Declaration of Conformity User manual The price is a net price. Price does not include shipping costs. For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website.