Gear Grinding Machine

HÖFLER H 1500

Condition: used, Year of construction: 1984, functionality: fully functional, travel distance X-axis: 1,800 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 2,000 mm, table load: 5,000 kg, spindle diameter: 110 mm, total height: 3,800 mm, total length: 5,000 mm, total width: 3,000 mm, table length: 1,520 mm, table width: 1,225 mm, feed length X-axis: 1,800 mm, feed length Y-axis: 1,500 mm, feed length Z-axis: 2,000 mm, Tool holder SK50, Heidenhain control, machine is ready for collection and immediately operational. Nledpsxga Tnefx Aazsg

Condition: good (used), Year of construction: 2000, gear diameter: 449 mm, Equipped with: Fanuc 150MB CNC Control Dry Cutting Cutter Shroud Chip Evacuation System Auto Doors Hydraulic System Lubrication System Work light Stack Light Specifications: Largest Speed Ratio: 10:01 Work Area (Continuous): Largest Depth of Teeth: 15.24 mm Largest Width of Tooth Face: 50.8 mm Work Area Axis: Horizontal Movement X Axis: -114 - 178 mm Vertical Movement Y Axis: -178 - 190 mm Movement of the Carriage Baseplate Z-Axis: -10.16 - 500 mm Workpiece Headstock Swiveling Range B-Axis: -3 - 90 Degree Maximum Distance Machine Center to Spindle Side: 165 mm Number of Teeth: 5-200 Inclusive Max. Gear Pitch Dia. of Typical 35 Deg. Spiral Angle Gear Using Max. Cutter Dia. 12" Cutter at the Following Ratios: Face Milling 1 x 1 - 13.5" - 342.9mm Nsdpfx Aajruakgezslg 2 x 1 - 16.0" - 406.4mm 5 x 1 - 17.7" - 450.0mm Face Hobbing (210mm Dia. Cutter) 1 x 1 - 10.560" - 268.22mm 2 x 1 - 10.286" - 275.00mm 5 x 1 - 11.810" - 300.00mm Milling Head Diameter: Helixact: 100,125,169,200,250,320mm Continuous Gumption Procedure, Teichloroethylene: 102 - 210 mm Workpiece Spindle: Drilling of Large Diameters: 5 3/64" Cone Upward Gradient on 304.8 mm (1 Foot): 21/32" Deep One of the Cone: 5.29" Diameter of the Whole Spindle Perforating: 3.35" Speeds: B-Axle Workpiece Headstock Drag Axis: 30 Degrees A-Axle Workpiece Spindle Number of Revolutions: 0 83 min-1 X-Axis Horizontal: 80 mm/sec Y-Axis Vertically: 80 mm/sec Z-Axis Carriage Baseplate: 80 mm/sec Space Requirement L x W x H (Approximate): 4.75 x 3.40 x 2.54m / 188" x 134" x 100" Machine Weight (Approximate): 10980 kg / 24,156#

Condition: good (used), Year of construction: 2009, max. wheel diameter 1200 mm gear width 260 mm max. module 16 min. module 0,5 stroke 270 mm Nlodpfxjwzmpze Aazsg distance between table/spindle 920 mm taper of shaper cutter SK control Bosch MTX table diameter 900 mm min. workpiece diameter-at internal hobbing 1200 mm strokes - infinitely variable 50-1000 Hub/min spindle diameter 125 mm table hole 320 mm Distance of shafts Min/Max 0-820 power capacity Stosskopf 30 KW total power requirement 72 KVA weight of the machine ca. 24 t dimensions of the machine ca. 6,5x2,9x4 m Liebherr LH 90 control, 9 axis CNC, top condition.

Condition: used, Year of construction: 1973, spindle diameter 130 mm x-travel 3000 mm y-travel 2000 mm total power requirement 4,5 kW Nedpfxst Hwt Sj Aazjlg weight of the machine ca. 30 t Spindle Ø 130 mm Spindle taper SK 50 Working range: X = column, longitudinal 3,000 mm Y = headstock, vertical 2,000 mm Z = spindle stroke 1,000 mm Lower table 3,300 x 2.400 mm Max. weight on table 10 tons/m² Min./ max position of work spindle above table 770 / 2,770 mm Feeds 0.9 - 2,000 mm/min Quick feed for headstock and column 5,000 mm/min Quill feed 0.5 - 1,200 mm/min Speed range, partially infinitely variable 4.5 - 1,250 rpm Weight, approx. 30,000 kg Accessories / Special Features * HEIDENHAIN Digital Display for 3 axes. * Hardened guideways. * Ball screw spindles. * Infinitely variable spindle speeds and feeds. Feeds can be individually driven with motor. * Moving operating platform. * Hanging control panel. * Manual operating control. * Platform. * Hydrostatics in the column displacement. * Mounting plate 3,200 x 2,500 mm, planed, with t-slots. * Top table approx. 1,400 x 2,600 x height 900 mm, one face is handled. * Hydraulic clamping of column and slides. * Motor driven tool clamp. * Lots of accessories, including tool holders with and without tools, separate chip extractor, clamping aids, 1 angle plate, and other plates. Lots of other accessories. This is a strong machine which is very suitable for heavy cuts and therefore ideal for the machine tool industry and for tool manufacturers. Condition : Good. Machine can soon be inspected under power. Delivery : Ex stock as inspected Payment : Net, after conclusion of contract Thank you for your interest. We have other horizontal borers on stock. Please let us know what you need.

Condition: used, Year of construction: 1998, Technical details: max. module: 7 weight of the machine ca.: 5 t worm grinding diameter: 280-350 mm width of grinding worm: 84-104 mm min. number of teeth: 6 Nedozgw I Njpfx Aazolg max. number of teeth: 600 max. top circle diameter: 360 mm max. workpiece weight: 60 kg with Turbo Separator, loading unit, latest-generation balancing and dressing unit and various accessories *

Year of construction: 1997, condition: ready for operation (used), Travel X/Y/Z: 1300mm/1100mm/1000mm, table dimensions X/Y: 800mm/800mm, number of pallets: 14, max. table load: 2200kg, table indexing: 0.001°. Speed: 7000rpm, spindle power: 50hp, tool magazine: 80, dimensions X/Y/Z: approx. 7000mm/3400mm/3800mm, weight: approx. 24000kg. On-site inspection is possible. Nljdpfx Aetx Dn Ujazjg

Condition: excellent (used), Year of construction: 2011, operating hours: 2,450 h, travel distance X-axis: 6,000 mm, travel distance Y-axis: 12,001,400 mm, travel distance Z-axis: 18,001,790 mm, controller manufacturer: Heidenhain, controller model: iTNC 530, workpiece weight (max.): 3,000 kg, total height: 4,700 mm, total length: 12,700 mm, total width: 7,800 mm, rotary table diameter: 2,200 mm, rotational speed (max.): 200 rpm, overall weight: 57,000 kg, spindle speed (max.): 8,000 rpm, operating hours of spindle: 2,450 h, coolant supply: 40 bar, number of slots in tool magazine: 60, tool length: 460 mm, Equipment: chip conveyor, documentation/manual, CNC controller: Heidenhain iTNC 530 Axes X-axis travel mm: 6000 Y-axis travel mm: 1200/1400 Z-axis travel mm: 1800 (H) / 1790 (V) C-axis degrees: 360º (0,001) A-axis degrees: ±180° B-axis degrees: ±180° Rapid traverse m/min: 30 Worktable Table dimensions mm: 6000x1235 Milling/turning table nc: Table dimensions mm: Ø2200 Max. workpiece weight kg: 3000 Nlodpfxszb H Tfs Aazjg Table rotation speed rpm: 200 max. torque Nm: 4600 Spindle Spindle speed rpm: 8000 Spindle drive power kW: 33/24 (40%ED/cont) Spindle torque Nm: 382/278 (40/100%ED) Cooling Cooling through the Spindle Center bar: 40 Tank capacity: 900 Tool system Tool holder: HSK-A 100 Tool magazine slots: 60 With free neighboring places mm: 200 With occupied neighboring places mm: 104 Max. Tool Length mm: 460 Max tool weight kg: 25 Chip-to-chip time s: 9.8 Equipment Electronic Handwheel Chip conveyor Infrared probe Internal cooling lubricant supply Rinsing gun Operating mode 4 blowing air through spindle center selectable via M-function Workarea light DXF import function Paper band filter Automatic door Indexing Head Set Up for Shaft Machining Axles can be hydraulically locked using the M function Machine running times Under power: 29447 Spindle Working: 2450 Basic machine dimensions / weight Length mm: 12700 Width mm: 7800 Height mm: 4700 Weight kg: 57000

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, Soraluce model FL8000 high performance travelling column, floor type CNC milling machine TRAVEL (X) 7,500 mm TRAVEL (Y) 1,400 mm TRAVEL (Z) 1,000 mm RAPID TRAVERSE (X,Y,Z) 25,000 mm/min WORKING FEED RANGE (X,Y,Z) 1 – 10,000 mm/min ACCELERATION RATE (Instantaneous not maximum) 1 m/sec2 SPINDLE SPEED 20 - 4,000 Rpm SPINDLE TAPER ISO 50 SPINDLE POWER 28 Kw NC15C - HEIDENHAIN iTNC 530 (Flat 15.1" TFT Screen with digital drives). Single processor version. Prepared for a machine of 10 motors (9 CNC axes + spindle motor). Main push button panel with individually operated push buttons for linear axes (X+, X-, Y+, Y-, Z+, Z-) K20 option for the i530M. Independent AC. Heidenhain digital drive servomotor for each axis HEIDENHAIN HR-410 portable electronic handwheel with 5m spiral cable Automatic Indexing head 28Kw, 760Nm, 0.001°x 0.001°, 4000 Rpm. Continuous air and oil mist lubrication system for head gears. Automatic Tool Clamping device – 15,000N. Automatic hydraulic tool releasing device Spindle taper: BT50 High Torque spindle motor 28kW, 100% ED, digital motor. R10 – ZF gearbox two speed including cooling unit Spindle Speed Range 20 – 4,000Rpm Rapid Feed X-Y-Z axes 25.000mm/min Working Feed range X-Y-Z axes 0 - 10.000mm/min Acceleration rate X- Y -Z axes 1 m/s2 (instantaneous, not maximum) Hydraulic counterbalance system for head/ram assembly X axis driving system by two servomotors, two gearboxes and a double rack & pinion Preloaded ballscrews with double recirculating nuts in Y and Z axes. Automatic centralized lubrication system. Linear Guiding System with recirculating cylindrical rollers in each axis. Automatic centralized lubrication system for the guides. HEIDENHAIN Linear measuring scales in X-Y-Z axes with compressed air purge system - (Precision +/- 0,005mm) H48 – Coolant through the spindle type AD. M3 – Automatic tool changer 40 stations. M6 – Horizontal-vertical tool changing facility. M8 – Motorized tool changing device. Tool changer is driven by a servo motor Hydraulic equipment Front metallic roller blind cover to both upper and lower ram area, together with metallic protection to the lateral side of the column, between the machine table and the rear guideway support, which protects the vertical movement of the ram. CE10 - PROTECTION on the back and both lateral sides of the machine column P20 - Operator's platform fixed to the column and travels together with it in the "X" axis direction. The main operator’s panel is mounted within the operator's platform area for machines without an operator’s pendant and is accessed from the rear of the machine. D7 + D50A - Coolant system with 1000L capacity tank with two pumps providing high and low pressure providing 5 & 12bar and 50L/min flow rate. Paper and Magnetic filtering. E30A – swarf conveyor FL8000 Hinge conveyor belt. Width 350mm PW11B – Pendulum working area system. PM2 x 2 – Machine prepared by Soraluce for the inclusion of two rotary tables. Working area lighting. Electrical cabinet cooling system Electrical cabinet lighting Working methods - According to CE safety regulations Filter to assure electromagnetic compatibility. Protection to both sides of the column with security bumpers Anchoring Bolts Njdpfx Aow U Tlzeazjlg Standard Colour - Blue RAL 5005 / Grey RAL 7035 K19 – Two sets of machine documentation (One hard copy, one on CD ROM) Floor plate 8,000 x 1,500 x 300mm

Condition: used, Year of construction: 2007, x-travel 900 mm y-travel 300 mm z-travel 1000 mm control Siemens Sinumerik 840D max. workpiece diameter 1600 mm Nljdpjw Rrb Hsfx Aazog max. module 20 mm tip circle diameter 350 mm Milling arbour diameter 375 mm Total closing value 80 kVa weight of the machine ca. 33,5 t dimensions of the machine ca. 10,530 x 6,375 x 4,680 m Feed rate: - X-axis 1 to 3000 mm/min - Y-axis 1 to 3000 mm/min - Z-axis 1 to 4000 mm/min Spindle speeds in rpm: - Tool 26 to 265 - Workpiece table 0 to 8 Equipment/accessories: - M 2 motor milling head - Milling mandrels - Oil cooler - Technical documentation

Year of construction: 2006, condition: good (used), 5-axis vertical machining center fully equipped with direct-drive technology. Machine equipped with 30,000 rpm spindle, 60-place tool magazine and Heidenhain TNC 530 CNC Nlodpfx Aepkyn Roazsg