Painting chain of approximately 280 linear meters, complete with tracks, chain and towing motor.

Condition: ready for operation (used), Year of construction: 2009, machine/vehicle number: 19500648, functionality: fully functional, workpiece length (max.): 3,500 mm, workpiece width (max.): 130 mm, workpiece height (max.): 120 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Bdedpfx Ajzln D Eem Tsf Max. profile length: 3,500 mm Max. profile width: 130 mm Max. profile height: 120 mm MACHINE DETAILS Number of milling and drilling units: 7 Max. Friedrichs motor speed: 18,000 rpm Max. machine motor speed: 1,500 rpm Electrical operating voltage: 400 V, 50 Hz Required network voltage: 20 kW Cable connections: 400 V NPE Operating height of the control cabinet: 1,050 mm Pneumatic operating pressure: 6 - 7 bar Pressure consumption per cycle: Approx. 3,500 NI Pneumatic line pressure at 70 °C: Approx. 15 bar EQUIPMENT Automatic screw feeder Arrangement of the units: On a wheel, which enables machining at different angles.

Condition: new, Year of construction: 2026, functionality: fully functional, total length: 30,000 mm, total height: 4,300 mm, total width: 6,500 mm, workpiece weight (max.): 100 kg, temperature: 220 °C, heating capacity: 80 kW (108.77 HP), workpiece height (max.): 1,200 mm, workpiece length (max.): 2,500 mm, insulation material: Mineralwolle 75 kg/m³, insulation thickness: 150 mm, workpiece width (max.): 800 mm, The continuous system consists of the following components: Chemical pre-treatment by spraying Bodpfx Amsum Ufls Tedf Dryer Powder coating system Powder curing oven Conveying technology (cycle process) Electrical control system

Condition: ready for operation (used), Year of construction: 2006, machine/vehicle number: 19500624, functionality: fully functional, operating pressure: 7 bar, rotational speed (max.): 18,000 rpm, working height: 1,000 mm, No minimum price – guaranteed sale to the highest bidder! The new price of the machine was €950,000! TECHNICAL DETAILS Milling units / Motor power Bsdezlnxijpfx Am Tsdf Motor power, small milling cutter: 0.27 kW Frequency, small milling cutter: 300 Hz Speed, small milling cutter: 18,000 rpm Motor power, large milling cutter: 1.1 kW Frequency, large milling cutter: 200 Hz Speed, large milling cutter: 12,000 rpm Tool data / Milling cutter data Collet diameter, small milling cutter: max. 8 mm Milling cutter diameter, small milling cutter: max. 8 mm Collet diameter, large milling cutter: max. 10 mm Milling cutter diameter, large milling cutter: max. 14 mm Electrical data Operating voltage: AC 400 V 3 N/PE Frequency: 50 Hz Rated current: 35 A Control voltage: 24 V Pneumatic data Working pressure: 0.7 / 1 MPa (7 / 10 bar) Compressed air consumption: 170 l/min Load limit of pneumatic lines at 70 °C: approx. 15 bar Working height Working height: 1,000 mm EQUIPMENT Clamping units Vertical clamping Maintenance unit with filter pressure regulator Control cabinet / Saw with lockable main switch Cutting unit: Allows cutting angles of 45 degrees and 90 degrees Machining units: Includes machining units and profile bearings Tools: Two screwdrivers, three cut-off wheels

Year of construction: 2005, condition: ready for operation (used), functionality: fully functional, power: 14 kW (19.03 HP), input current: 80 A, workpiece length (max.): 4,000 mm, machine/vehicle number: 6080008129, TECHNICAL DETAILS Maximum profile width: 130 mm Maximum profile height: 205 mm Maximum workpiece/profile length: 4,000 mm Processing capacity: 80 units MACHINE DETAILS Connection: 3 N/PE 400 V Frequency: 50 Hz Current: 80 A Power: 14 kW Bjdpfszlnvuox Am Tedf EQUIPMENT Powered, continuously adjustable gripper Lifting function for smooth feeding Profile guidance on rollers Internal gripper to prevent damage to the profiles Integrated measuring sensors for workpiece length control Workpiece removal via outfeed table Portal design for high profile cross-sections Industrial PC with Windows operating system Barcode scanner

Condition: new, Year of construction: 2026, functionality: fully functional, power: 88 kW (119.65 HP), temperature: 220 °C, heating capacity: 30 kW (40.79 HP), workpiece height (max.): 1,500 mm, workpiece length (max.): 500 mm, insulation material: Steinwolle, insulation thickness: 150 mm, workpiece width (max.): 500 mm, Scope of delivery: Bdodpfeulwg Njx Am Tsf 1. chemical pre-treatment by spraying (in cycle process) 2. dryer 3. powder coating system 4. single powder oven 5. conveyor technology, semi-automatic 6. electrical control system Hall/ floor space Floor area of the system max. 12,000 x 6,500 mm Hall floor Industrial floor Workpiece sizes Max. Part dimensions L= 500mm, H= 1,500mm, W= 500mm Range of steel parts Conveyor technology P&F chain conveyor in cycle mode, semi-automatic Pre-treatment Chemical Power supply Electricity On-site power (max. 88 kW) Gas On-site power Compressed air On-site power Water On-site power Calculation Type of system Cycle system Conveying speed 3.2 meters / min Length per cycle L = 1,600 mm Time for cycle movement: Tm = 1.6 meters : 3.2 meters/min = 0.5 minute Time for cycle standstill: Ts = 8.5-12 minutes Total time for cycle Tt = Tm + Ts = 9-12.5 min Electrical energy: Total power 88 kW min. Average consumption 60 kWh max. average consumption 70 kWh

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2015, operating hours: 4,125 h, load capacity: 8,000 kg, lifting height: 3,600 mm, mast type: duplex, fork length: 2,050 mm, overall weight: 13,948 kg, An oil change was performed before the sale. Only the hydraulic oil was not changed. The filters have been replaced. TECHNICAL DETAILS Load capacity: 8,000 kg with load center at 900 mm Residual load capacity with Kaup 10T160 fork positioner: 7,320 kg with load center at 900 mm Tractive force with/without load: 45.6 kN Lifting height: approx. 3,600 mm Fork length: approx. 2,050 mm MACHINE DETAILS Engine: LPG GM 5.7L V8 Cylinders: 8 Displacement: 5,700 cm³ Rated speed: 2,200 rpm Power: 85 kW Operating hours according to display: approx. 4,125 h Operation: Solo-Pilot with multi-function display Dimensions & Weight Overall length including forks: approx. 5,950 mm Overall width: approx. 2,150 mm Height with mast retracted: approx. 3,160 mm Height with mast extended: approx. 4,960 mm Height above protective roof: approx. 2,705 mm Self-weight: approx. 13,948 kg EQUIPMENT Kaup 10T160 fork positioner Duplex mast 3rd + 4th control circuit Side shifter Bdjdozlhnqopfx Am Tsf Solo-Pilot Single pedal control Work lights front and rear Full cabin with heater Note: The two tires on the steering axle, as well as the fork tines, should be replaced. This can be requested and carried out by the seller. Fork tine length would be selectable.

Condition: used, Year of construction: 2007, operating hours: 39,023 h, machine/vehicle number: 1315318, laser power: 5,000 W, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, workpiece weight (max.): 900 kg, No minimum price – guaranteed sale to the highest bidder! The machine has not been powered on for approximately one year. TECHNICAL DETAILS Laser power: 5,000 W Working area (X x Y x Z): 3,000 mm x 1,500 mm x 115 mm Sheet metal thickness, structural steel max.: 25 mm Sheet metal thickness, stainless steel max.: 20 mm Sheet metal thickness, aluminum max.: 12 mm Maximum workpiece weight: 900 kg Positioning speed max.: 300 m/min Bdjdpozlhcnefx Am Tof Positioning accuracy: +/- 0.1 mm MACHINE DETAILS Control system: CNC Siemens Sinumerik 840 D Operating hours, laser on: 77,107 h Operating hours, beam on: 39,023 h Dimensions & Weight Machine dimensions (L x W x H): 11,100 mm x 4,600 mm x 2,400 mm Machine weight: 12,000 kg EQUIPMENT Automatic pallet changer NitroLine FocusLine PlasmaLine SprintLine ContourLine

Condition: new, ⭐⭐⭐⭐⭐ (5.0) 42 ratings ✈️shipping : 45-day delivery ✈️ ✅✅✅Energy class A+++✅✅✅ ⚡️ Top service ⚡️ Fast delivery ⚡️ Great support! ⭐€10,850 EXCL.VAT & SHIPPING⭐ ►►Buy It Now◄◄ ✳️Keep your liquidity! We offer a variety of financing models to ensure your investment has the best chance of success. Contact us today to learn more about our hire-purchase, warranty or lease programs. ✳️ ➖➖➖➖➖ ►►►⌛⏰ FASTEST delivery time❗ ⌛⏰►►► ✨✨Buy directly from the manufacturer and secure the price and quality advantage!✨✨ Benefit from Proton's 40 years of experience in surface coating technologies. ➖➖➖➖➖ ☘️Eco-Friendly☘️⚡️Green Energy⚡️☘️ ⭐ Paint Booth – WETLINE-SP-1500 ✔️ Internal dimensions: 1390 mm L * 1500 mm W * 1400 mm H ✔️Pool height : 561 [mm] ✔️Filter system : double layer water curtain ✔️Filtering material : city water, plate filter and mechanical separator with backwash ✔️Filter material cleaning : thin and thick grid ✔️ Pump output : 1.5 [kw/h] 940 [d/d] x 1 piece ✔️Number of fans : 1 piece Bdedoc Uthdopfx Am Tof ✔️Fan performance : 5,400 m3/h x 1 ✔️Fan motor power : 3 kw/h ⭐The cabins can be made of galvanized sheet metal or stainless steel. They can be designed to be integrated into the automatic and manual systems. ⭐At the pool there is a platform for material and personal safety. The platform covers the entire pool. ⭐In the Filterline wet painting booth, environmental pollution is prevented by the simultaneous use of 3 different filter systems. ⭐Wet paint particles, sucked in the air by a suction fan, are caught by the water curtain at the back of the cabin and transported into the pool. ⭐Wet paint particles in the trace amount that are not caught by the water curtain are caught by the separators on the suction ducts on the back of the water curtain, and the fresh air outlet is from the flue. ⭐The backwash system is applied in the separator section to help the process of retaining the wet paint particles of the separators. The filtration efficiency, whose contact area is increased by spraying wash water through the nozzles, is maximized. ⭐While paint dirty water accumulated in the basin enters the pump suction chamber, it goes through a coarse and a fine mesh to prevent clogging of the pump spray water, thus ensuring paint particles are retained. ⭐When the dirty water in the pool becomes unusable, it can be disposed of from the waste water valve located behind the grates in the suction department. ⭐By using a paint separator system, the water in the pool is cleaned from the paint and used continuously. ⭐The separated paint residues are drained by a filter press and must be disposed of properly. ⭐Price quoted is for the smallest standard size in stainless steel. All devices/machines are new, not used. Do you want a special configuration ❗ Call us now❗ ☀️ 2 YEAR WARRANTY ☀️ ☀️We have CE certificates for all our machines and ATEX certificates for the necessary machines.☀️

Year of construction: 2010, condition: ready for operation (used), functionality: fully functional, working length: 7,600 mm, machine/vehicle number: 1400040505, number of axes: 4, TECHNICAL DETAILS Max. machining length with end face machining: 7,600 mm Max. machining length without end face machining: 7,720 mm EQUIPMENT 12 pneumatic collet chucks 2 work areas 4-axis profile machining center; stepless machining between -90° and +90° with each available tool Automatic clamping position adjustment with absolute measuring system Two separate machining zones for tandem operation 4-axis control 18.5" color monitor, USB ports, and network connection Windows operating system EluCam software Automatic profile length measurement (on both sides) Bdjdezhuyfopfx Am Tjf Barcode scanner The traversing tool magazine ensures short tool change times and thus optimal machining cycles; the magazine can be equipped with eight tools. 8x tool holders with collet chucks

Condition: ready for operation (used), Year of construction: 2005, operating hours: 20,729 h, functionality: fully functional, travel distance X-axis: 980 mm, travel distance Y-axis: 630 mm, travel distance Z-axis: 630 mm, controller model: Heidenhain iTNC 530, rotational speed (max.): 18,000 rpm, TECHNICAL DETAILS Travel range X-axis: 980 mm Travel range Y-axis: 630 mm Travel range Z-axis: 630 mm Spindle speed range: 0–18,000 rpm Tool holder: HSK 63 MACHINE DETAILS Control system: Heidenhain iTNC 530 Clamping area: 1,250 × 700 mm Operating hours Machine operating hours: 46,922 h Program runtime: 20,279 h Spindle operating hours: 20,746 h Bdsdpfx Aozmry Tem Tjf EQUIPMENT Fixed angular table 3D measuring probe Heidenhain Tool measurement in the working area with BLUM laser Vertical tool changer with 32 magazine slots Full protective enclosure with sliding doors and interior lighting Electronic handwheel Operating modes 3 and 4 Chip conveyor Coolant system 3 height-adjustable machine feet Spindle cooler Control cabinet cooler from Rittal Operating manuals

Condition: new, Year of construction: 2025, ⭐⭐⭐⭐⭐ (5.0) ⚡ Top Service | Fast Delivery | Excellent Support ✈️ Delivery Time: Only 8 Weeks ✅ Energy Efficiency Class A+++ ☀️ 2-Year Warranty Buy Directly from the Manufacturer – Benefit from Over 40 Years of Experience in Surface Coating Technology! 💶 Flexible Financing Options: Maintain liquidity with our attractive hire purchase, leasing, and warranty programs. Contact us today for details! 🌀 Mono Cyclone & Jet-Pulse Filter Unit for Large Powder Coating Systems Ideal for operations that require efficient powder recovery: Powder is collected beneath the mono cyclone, sifted through a mesh, and transferred to the color station via pneumatic pumps. From there, it is automatically fed back into the powder coating guns. ✔ Key Advantages: Bdsdjdy E A Sspfx Am Tef No need for an exhaust air duct Clean and convenient powder recovery process Compatible with all automatic powder coating booths Suitable for walk-in type booths as well Optional: Use the Jet-Pulse filter unit alone for an environmentally friendly, recovery-free setup 🔄 High-Efficiency Recycling Technology Only 4% material loss Maximized powder reuse Fully compatible with Proton MA-RYC-PRO Color Station for optimized performance in automated systems 👉 More details available in our listings or on our website. 🎨 Color Options: Our standard color combinations: Yellow-White Anthracite-White Custom RAL colors are also available upon request – please note that additional charges apply. ✅ Your Benefits at a Glance: Fast delivery in 8 weeks Direct from the manufacturer Energy-efficient (A+++) Comprehensive warranty & support Flexible financing models State-of-the-art powder recovery system

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 500 mm, controller model: Heidenhain TNC 410, rotational speed (max.): 10,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Bjdozmryyspfx Am Tedf Travel range X-axis: 800 mm Travel range Y-axis: 500 mm Travel range Z-axis: 500 mm Spindle speed range: 0–10,000 rpm Spindle speed control: stepless Tool holder: SK 40 Magazine capacity: 20 MACHINE DETAILS Control system: Heidenhain TNC 410 Clamping area: 1,000 × 500 mm EQUIPMENT Fixed angular table Vertical tool changer Full enclosure with sliding doors and interior lighting Various tool holders SK 40 Electronic handwheel Coolant system with enhanced pump Coolant pressure: 20 bar Chip conveyor Operating manual

Condition: ready for operation (used), Year of construction: 2002, operating hours: 20,377 h, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 500 mm, controller model: Heidenhain iTNC 530, rotational speed (max.): 20,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 800 mm Travel range, Y-axis: 650 mm Travel range, Z-axis: 500 mm Speed range: 0–20,000 rpm Speed control: stepless Magazine capacity: 30 Tool holder: HSK 63 MACHINE DETAILS Bsdpfxszmrpuo Am Tedf Control system: Heidenhain iTNC 530 Clamping area: 900 × 600 mm Operating hours Machine operating hours: 54,796 h Spindle operating hours: 23,462 h Program run time: 20,377 h EQUIPMENT Fixed tilting table Vertical tool changer Full enclosure with sliding doors and interior lighting Electronic handwheel Tool measurement in the working area with BLUM laser 3D infrared probe Renishaw Chip conveyor Coolant system 4 height-adjustable machine feet Operating manuals

Condition: new, Year of construction: 2025, machine/vehicle number: 1018, THE POWERFUL BENDING MACHINE FOR EXTREME USE: The compact bending machine enables precise and repeatable bending up to an outer diameter of 100 mm stationary and directly at the assembly site. Transport is possible with lift trucks or the optional rollers. A powerful three-phase motor and a precision gearbox provide a powerful drive. The machine convinces with its compact and slim design as well as the very free bending range. Optimum bending accuracy is achieved by position detection directly on the bending axis. The bending angle is set easily and quickly via a convenient and menu-driven user interface in 14 languages with touchscreen control, which guarantees even more intuitive operation. For more complex bending tasks, 100 bending programs can be stored, with an angle sequence of max. 8 bends per geometry. The multifunction control allows variable adjustment of the bending speed for forward and backward travel, and a parameterizable overbending function is provided to compensate for material springback.With the help of the four material characteristics, the material is automatically overbent to the required bending angle, thus realizing an exact bending result. The principle of "stationary tube and rotating tool" ensures low space requirements during bending. Sliding shoes are used for thin-walled tubes to achieve a wrinkle-free bending result and to bend bends with minimal deformations from e.g. stainless steel and copper tubes. With the profile bending attachment PB20 flat, square and round bars can be bent without any problems. Extremely small bending radii are made possible with the KBV small bending attachment. Bdodsndk N Aopfx Am Tof POSSIBLE AREAS OF APPLICATION: - Plant engineering - Hydraulic piping - Meander bending - prototyping - Sanitary and heating engineering - shipbuilding TECHNICAL DATA 10000: Bending capacity: up to 100 x 5 mm, 55 mm solid material three-phase current 400 V - Bending radius up to 500 mm - Multifunctional machine control Bending angle adjustment (0,1°) - Maximum bending angle 240 - Safety foot switch with emergency stop - Weight 600 kg OPTIONAL ACCESSORIES: - Adapter system for tools from model series 3000/6000 with bending radius from 45 mm, incl. hexagonal shaft 40 mm - Profile bender PB20 - for bending flat and square bars up to max. 100 x 10 mm, round bars up to max. 20 mm - Small bending device KBV - Special tools according to specification - Software adaptations for special tasks OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: ready for operation (used), Year of construction: 1991, functionality: limited functionality, travel distance X-axis: 5,020 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 2,000 mm, spindle diameter: 100 mm, controller model: Heidenhain 415 B, TECHNICAL DETAILS Spindle diameter: 100 mm Travel in X-axis: 5,020 mm Travel in Y-axis: 1,000 mm Travel in Z-axis: 2,000 mm Tool holder: SK 50 MACHINE DETAILS Control system: Heidenhain 415 B Rotary table dimensions: 2,500 x 2,000 mm EQUIPMENT Indexable milling head 2.5 60-position tool changer Rotary table manufacturer: Scharmann Bedpfxszlryqj Am Tsdf Note: The rotary function of the rotary table is defective. The machine is sold without pallet changers.