Monzesi Rossi Monza 500

Monzesi Rossi Monza 500

Condition: refurbished (used), Year of construction: 2025, operating hours: 50 h, machine/vehicle number: 3018-04, Country of manufacture: Switzerland Voltage: 380/50/3 Net weight: 3100 kg Overall dimensions: 230x155x170 cm Installed power: 13 kVA Customs tariff position: 8460.2920 TECHNICAL SPECIFICATIONS MAIN DIMENSIONS Distance between centers: 650 mm Grinding capacity SpW+bs: -80 Stroke: 700 LONGITUDINAL SLIDE Max stroke: SpW+50 mm Minimum automatic feed: 1.5 mm Speed: 50-5500 mm/min Reversal delay: 0-6 sec Maximum table swivel: 12°/10°/8.5°/6° Pneumatic relief for table and workhead CROSS SLIDE Max stroke: 300 mm Rapid traverse: 60 mm Plunge grinding depth in diameter: 3.4 mm Feed 1: 0.012-6 mm/min Feed 2: 0.012-1.2 mm/min Feed per pulse: 0.001-0.05 mm GRINDING WHEEL HEADSTOCK Left-side wheel, external grinding: 400x80x127 mm Drive power: 5.5 kW Peripheral speed: 35 m/s RPM: 1670/2110 min-1 Internal grinding device for belt-driven spindles, including drive unit: 1.5 kW WORKHEAD Swivel range: 0-90° Continuously variable RPM: 30-1000 min-1 Hedpfx Aasw T Sd Tsdofc Internal taper: Morse 5 Collets: W-25 Drive power: 0.55 kW Maximum workpiece weight between centers: 130 kg Grinding load between centers: 100 Nm TAILSTOCK Internal taper: Morse 3 Quill stroke: 35 mm Fine adjustment for cylindricity correction: ± 40 μm TECHNICAL CHARACTERISTICS: GUARANTEED WORKING ACCURACY Straightness of the generator over 630 mm: 0.003 mm Roundness during chuck grinding: 0.0003 mm CONNECTION VALUES Maximum absorbed power: 13 kVA Maximum permitted voltage fluctuation: -15%/+10% Maximum permitted frequency variation: ± 3% Required compressed air pressure: 5 bar Unless otherwise stated or in case of error or omission, these technical details are provided without engagement.

Condition: good (used), Year of construction: 2001, functionality: fully functional, Grinding wheel 508x254 (305) mm, regulating wheel 330x254 (305) mm, regulating wheel speed 0-115 rpm, grinding wheel rotation speed 45 m/sec, grinding diameter 2-150 mm, grinding wheel drive 45 kW, machine weight 6.5 tons, space requirement approx. 3.0x1.5 m The machine will be equipped with a new Siemens S7 control system with new control panel, dressing quill SS electrically controlled via servo motor. Machine will be completely checked, defective parts repaired or replaced. Hfjdpfjuy Ifgjx Aadsc Various options possible (KM system, infeed/outfeed, workpiece rulers etc.)

Condition: excellent (used), pressure 0,5 - 20 t max. workpiece diameter 5 - 75 mm threading length 2000 mm pitch in mm 8 mm diameter of roll spindle taper 69,85 tool diameter 200 mm roll spindle turning speed range 20 - 90 U/min stroke 0 - 20 mm total power requirement 7,5 kW Hsdpfx Aaevpaa Redjfc weight of the machine ca. 3,1 t dimensions of the machine ca. 1,9 x 1,1 x 1,2 m

Condition: used, Tool presetter EZSET EZ400 Hjdpfsuhb Stex Aadefc

Condition: new, Year of construction: 2024, == Exhibition machine == ALZMETALL column drilling machine ALZSTAR 40 SV with coolant unit B (option 25) (consisting of separate tank (33l), pump with motor protection switch, complete fitting) Hsdpfx Aaod Hy Elodefc and LED machine light Standard equipment: Mushroom pushbutton, reversing switch (for clockwise and anticlockwise rotation), motor protection switch Infinitely variable speed adjustment, digital speed display, feed overload protection, protection class IP54, connection plug Spindle protection with electrical fuse Technical data: Drilling capacity steel E335 (St 60) 40 mm Thread cutting: Steel E335 (St 60) M 24 Cast iron EN-GJL-200 (GG20) M 30 Short spindle MK 3 Spindle stroke 120 mm Projection 293 mm Column diameter 115 mm Machine table, usable support 514 x 360 mm T-slots, number x width x distance 2 x 14 x 224 mm Spindle-to-table distance min./max. 117/701 mm Feed rate 0.10 + 0.20 mm/rev Machine height without options approx. 1840 mm Net weight approx. 285 kg Drive stepless Motor 1500 / 3000 rpm Power 1.45 / 1.9 kW Spindle speed 160-2250 rpm

Condition: refurbished (used), Year of construction: 1988, functionality: fully functional, Löser centerless tube grinding machine - belt grinding machine - polishing machine - Cylindrical grinding machine Hfsdpfx Aepugwieadec Centerless tube grinding / polishing machine for workpieces with a minimum length of 1100mm. The machine was built in 1988 and was completely overhauled in 2012. The machine was converted for polishing and then only polished around 10,000 parts. The machine was no longer used after that. During the general overhaul, the motors, bearings and the entire control cabinet with the frequency converters were completely replaced. The machine can be used for both wet grinding and polishing. Wastewater treatment including pumps is not yet available. We can retrofit these for you free of charge according to customer requirements. The transport systems (roller conveyors) between the grinding stations must also be retrofitted to suit your workpieces. The machine can process pipe diameters from 10mm to 160mm. The grinding motors / polishing motors have an output of 7,5kW per station. The system can be viewed by appointment in our warehouse in D-63128 Dietzenbach.

Year of construction: 2002, condition: ready for operation (used), With two machining modules, X-axis: -50 to 725mm, Y-axis: -200 to 300 / -250 to 250mm, rapid traverse X-, Y-, Z-axis: 18/12/30m/min, control: Siemens Sinumerik, temperature range: 5–40°C, power type/frequency: 3 PEN / 50Hz, rated voltage: AC 400V, control voltage: DC 24V, auxiliary voltage: AC 230V, connected load: 102kVA, rated current: 148A, rated current (fast): 148A, fuse (slow): 160A, length: 8000mm, width: 3000mm, height: 4000mm, weight: approx. 17t, operating hours: approx. 80,000h. The machine is fully functional, the ball screw drive (recirculating spindle) of the Z-axis was renewed in 2024 and it has been regularly maintained. Comes with documentation, control cabinet, hydraulic unit, filter elements, and chip conveyor. An on-site inspection is possible. Hfjdpswbuyzofx Aadsc

Condition: refurbished (used), CN Centerless grinding machine ROSSI MONZA 1500 CN currently being overhauled and fully electrically/electronically retrofitted Siemens electronics with touchscreen, brushless motor on Z (workpiece diameter) and regulating wheel (adjustable RPM), step motor on grinding wheel dressing increment, auto size compensation after grinding wheel dressing Hfjdpsmmqirofx Aadec Grinding wheel 350 mm * 610 mm dia This machine can be inspected in our warehouse in Gussago BS Italy Centreless grinding is a procedure for grinding cylindrical bodies and is used for mass production of rollers cylindrical, conical rollers, jet needles, pump pistons, hydraulic sliders, crosses, drills etc. During centerless plunge grinding, the workpiece is ground in one pass thanks to the translation of the grinding wheel. For this purpose, the grinding wheels and the adjustment discs have a negative profile of the piece to work which is given to them with the aid of a tool. The through-feed grinding or also through grinding and longitudinal grinding: pieces to be worked proceed uninterruptedly with axial feed through the rectification gap. Grinding wheel width: 350 Grinding wheel diameter: 600 CNC: Siemens

Condition: good (used), Studer S30-12 cylindrical grinding machine TECHNICAL DATA Main dimensions Center height: 125 mm Center width: 400 / 700 / 1025 mm Largest longitudinal slide path: 400 / 700 / 1000 mm Longitudinal slide Table speed: 50 - 5000 mm/min Hsdpfjvca Izox Aadofc Reversing delay: 0-6 s Smallest automatic travel: 1.5 mm Max. stroke: 400 / 700 / 1020 mm Max. Table inclination: 12 / 30 / 78° Cross slide Swivel range: +- 45° Quick adjustment: 40 mm Feed path with handwheel: 20 mm Largest plunge depth: 1.7 mm Sanding headstock Grinding wheel diameter x width x bore: 450 x 80 x 203 mm Speed: 1340 / 1500 1625 / 1800 / 2000 / 2200 rpm Coarse adjustment: 210 mm Workpiece headstock Swivel range: 0 - 90 Speed range: 30 - 675 rpm Mounting cone: Morse 5 Collets: W25 Tailstock Mounting cone: Morse 3 Adjustment travel of the center: 30 mm Total power requirement: 5 / 8.25 kW No liability is assumed for the correctness, completeness and up-to-dateness of the information.

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, The positions of the rotating tools are: T01-02-03-04 / T22-23 / T34-35 - equipped with Iemca Boss 332E/32 new in 2006 - lot of collets / guide bushes - MSC-501 Control - the machine has always worked with oil. Hedpfxjwpu Eto Aadofc