Used Big Bale Press for sale (27,907)

Condition: good (used), Year of construction: 2016, functionality: fully functional, Vertical baler HSM V-Press 1160 plus, year of manufacture 2016 Technical Data: Manufacturer: HSM Model: V-Press 1160 plus Year of manufacture: 2016 Pressing force: 55 t Drive power: 4 kW Idle cycle time: 25 s Filling height: 1115 mm Feed opening: 1195 x 650 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Dimensions: 1700 x 1800 x 2200 mm (W x D x H) Weight: 2430 kg Materials: Paper, cardboard, film Rcsdpfx Ahox Irw Re Uok The baler is in good condition. Operator's manual and CE declaration are available. Inspection can be arranged at any time, including under power. Upon request, we can also carry out test runs with your material for a handling fee. We are happy to answer your questions about the machine by phone from Monday to Thursday from 08:00 to 14:00. On Fridays we are available from 08:00 to 13:00. Please note: All technical data are based on the manufacturer's information. We do not assume liability for the given data or possible errors. Offer is subject to change, prior sale reserved, and may be revoked at any time. Inspections are possible by prior arrangement. Sale is ex works, prepayment required, without warranty or guarantee.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Rcedpfox A U Ncsx Ah Ujk Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: ready for operation (used), Year of construction: 2013, Brand: HSM Model: V-press 860 plus Year of manufacture: 2013 Pressing force: 418 kN Voltage: 400 V Max. bale weight: 430 kg (depending on material) Bale dimensions: 120 x 110 x 85 cm Rodpfjx E Skxjx Ah Ujck Machine weight: 2,083 kg Machine dimensions: 180 cm x 125 cm x 298.5 cm Filling opening dimensions: 120 cm x 65 cm x 85 cm Condition: Very good! Functionality checked. FLITS Rental & Sales Service: Each machine comes with a bundle of baling wire (120 wires). Need additional bundles of baling wire? Request a free quote. FLITS Rental & Sales is your reliable partner for the sale and rental of high-quality machinery for both businesses and private customers. We focus on providing efficient solutions for materials handling, cleaning, waste processing, and working at height. At FLITS Rental & Sales you will find a wide range of machines suitable for use in various sectors. Check our listings for: balers for efficient waste processing, electric pallet trucks/stackers for fast and safe materials handling, scrubber dryers for thorough and professional floor cleaning, forklifts in a variety of models suitable for different work environments. With FLITS Rental & Sales you choose speed, clarity, and reliability. We think along with you, respond immediately, and ensure you quickly receive the right machine. Do you have questions or would you like a free quote? Feel free to contact us. Waste baler, paper baler, cardboard baler, plastic baler, waste compactor, recycling, textile press, waste, waste processing

Condition: used, Year of construction: 2011, machine/vehicle number: 340000674, The HSM V-Press 403 baler is a compact solution for the efficient compaction of waste and recycling materials. This used baler offers excellent performance and is ideal for companies looking to optimize their waste management and save space. With its robust design and user-friendly operation, it is perfect for use in various industries. Technical details: Machine no. 6113.114 Serial number 340000674 Rcsdpfx Ahjunzn Ns Usk Pressing force: 33 kN Power supply: 400 V / 50 Hz Dimensions: approx. 1,200 x 800 x 1,500 mm (L x W x H) Output: 1.1 kW Rated current: 2.6 AMP Year of construction: 2011 Weight: approx. 300 kg

Year of construction: 2001, condition: good (used), HSM-500.1_VL PRESS PAPER PRESS FILM PRESS BALER Rcodpfxolc Du Ne Ah Uok ready to use good CONDITION used & good / see photos model: HSM 500.1 VL machine no. 6135.244.P serial no. 220109689 pressing pressure 50 tons V 400; Hz 50 KW 7,5 Amp. 15,5 Pressing force 6 tons Year of manufacture 2001 more presses in our other offers article used and good / roughly cleaned (plug in and go ) dimensions: on request !!! Other photos are for further use possibility. All items seen in photos also available from us. Price quotation net per piece for pickup from stock 47441 Moers current stock 1 piece Viewing is expressly offered. more technology in stock see photos or ask by phone General: We offer here from various acquisitions articles, which we describe as well as possible, as well as set meaningful photos. Further details about the article can not be made. We offer the possibility of Tuesday and Thursday in the time between 9 and 16 o'clock after telephone appointment to visit. If necessary, the article can be taken away immediately. Answers to this article we can offer due to time constraints only if you provide us with a phone number when you request. This offer, unless specifically described, is USED GOODS. Any packaging may be damaged. Items have been visually inspected and are as far as technically ok. All offers ex stock 47441 Moers. If you want shipping, please contact us to discuss packaging and shipping costs. Call with interest gladly by. all dimensions are approximate Errors in the description expressly reserved.

Condition: ready for operation (used), Year of construction: 2012, pressing force: 40 t, Manufacturer: HSM Redpfox D U N Sox Ah Usck Model: HL 4010 Year of manufacture: 2012

Condition: good (used), Year of construction: 2019, operating hours: 492 h, functionality: fully functional, Vertical baler HSM V-Press 1160 plus, year of manufacture 2019 Technical Data: Redex E S Anepfx Ah Ueck Manufacturer: HSM Model: V-Press 1160 plus Stock No.: 9969 Year of manufacture: 2019 Operating hours: 492 Pressing force: 55 t Drive power: 4 kW Idle cycle time: 25 s Filling height: 1115 mm Filling opening: 1195 x 650 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Dimensions: 1700 x 1800 x 2200 mm (W x D x H) Weight: 2430 kg Materials: Paper, cardboard, film The baler is in good condition. Operating manual is available. Please note: All technical data is based on manufacturer's information. We do not accept any liability for the details provided or for possible errors. All offers are subject to change, prior sale reserved, and can be revoked at any time. Inspections are possible upon prior arrangement. Sale is ex works, without warranty or guarantee. Our payment terms: 100% advance payment.

Condition: used, Year of construction: 2006, Bale size 400x400 mm Force 1 Step 850 KN Force 2 Step 850 KN Force 3 Step 850 KN Steel < 8 to/h Aluminium < 4 kg/h Driving Power 50 KW Arrangement Surface 7,5 x 7,2 m x m Machine weight 29 to Press box aperture1,9 x 0,95 mxm Rcedoltinwspfx Ah Uok Place: Germany Available immediately

Condition: ready for operation (used), Year of construction: 2012, Brand: DIXI Model: 60 Sh Year of manufacture: 2012 Pressing force: 60 tons Voltage: 400V Maximum bale weight: 340-500 kg Bale dimensions: approx. 120 x 80 x 80-110 cm Machine weight: 2,400 kg Machine dimensions: 190 cm wide x 140 cm deep x 230 cm high Filling opening dimensions: 115 cm x 80 cm deep x 55 cm high Condition: Very good! Functionality checked. FLITS Rental & Sales service: With every machine, we supply a bundle of binding wire (120 wires). Need more bundles of binding wire? Request a quote with no obligation. FLITS Rental & Sales is your reliable partner for the sale and rental of high-quality machines for both businesses and private individuals. We focus on delivering efficient solutions in the areas of internal transportation, cleaning, waste processing, and working at height. At FLITS Rental & Sales, you will find a wide range of machines suitable for deployment in various sectors. See our advertisements for: waste balers for efficient waste management, electric pallet trucks/stackers for fast and safe internal transport, scrubbers for thorough and professional floor cleaning, forklifts in various designs suitable for different working environments. Rsdex Af Ntjpfx Ah Usck With FLITS Rental & Sales, you choose speed, clarity, and reliability. We think along with you, respond immediately, and ensure that you quickly have the right machine at your disposal. Visit our location You are very welcome to view the machines at our premises. We are located at: Schoterlandseweg 94, 8413NE Oudehorne, Netherlands. Visits are possible by appointment, so we can take the time to inform you thoroughly and show you the right machines. Contact Do you have questions or would you like to receive a no-obligation quote? Please feel free to contact us: We are happy to help you further. Waste baler Paper baler Cardboard baler Plastic baler Waste compactor Recycling Textile baler Waste Waste processing DIXI

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Redpfx Aevq Rtksh Uock Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Rcedju Thhrepfx Ah Usk Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2008, power: 3 kW (4.08 HP), The HSM V-Press 610 is a powerful baler designed for medium to large volumes of waste, making it ideal for commercial and industrial use. This model combines high capacity, efficiency, and reliability, allowing for the effective compaction of a wide range of waste materials. Pressing force: 120 kN Drive power: 3 kW Filling height: 655 mm Filling opening (width x height): 800 x 495 mm Bale length x bale width x bale height: 800 x 600 x 600 mm Bale weight: 100 kg Dimensions (W x D x H): 1198 x 823 x 1986 mm Rodpfox Dk Tgjx Ah Uock Weight: 540 kg Related product line: V-Press Consumables: Strapping Compression materials: Plastic film, mixed paper, cardboard, punching waste! PRICE ON REQUEST!

Condition: good (used), Year of construction: 1981, functionality: fully functional, Equipment: documentation/manual, Automatic channel baler BOA Continu 25 LB + conveyor belt. The baler is in good condition and has been regularly serviced. Recently, the Denison pump underwent a complete overhaul. Fully functional and in continuous operation. Please contact us for further information. Redpfx Ajw S Tv Ush Uock

Condition: used, Year of construction: 1988, operating hours: 1 h, machine/vehicle number: V 516, total width: 2,000 mm, total length: 7,000 mm, total height: 1,800 mm, operating pressure: 300 bar, pressing force: 90 t, sheet thickness aluminum (max.): 5 mm, power: 11 kW (14.96 HP), empty load weight: 16,000 kg, cutting force: 90 t, year of last overhaul: 2025, Bale size 400x400 mm Rodjlhqd Rspfx Ah Usck Force 1 Step 900 KN Force 2 Step 900 KN Steel max. 2500-3500 Kg/Std. Aluminium max. 2000 - 3000 Kg/Std. Driving Power 11 KW Arrangement Surface 7x2x2,5 m x m Machine weight 16 to Place: Austria Aviable: 30.01.2025

Condition: good (used), Year of construction: 2011, functionality: fully functional, Compressive force 548 kN The size of the loading opening is 1,195 x 650 mm Bale weight up to 480 kg depending on material Binding with 4 x strapping band or 4 x wire Bale size 1,200 x 780 x max. 1,200 mm Dimensions 1,797 x 1,062 x 2,985 mm Rcjdpfx Asttayteh Uek Bodhzadl7zw The weight of the equipment is 2,030 kg

Condition: used, HSM V-Press 605 waste paper baler - used The HSM baler is a compact device for reducing packaging waste by up to 95%. It is designed to compact and crush cardboard (paper sacks, waste paper, offcuts) and film (stretch film, plastic sacks). It enables them to be disposed of economically. The waste paper baler has a graphic text display informing of the machine's stage of operation and a large waste loading opening. All this contributes to the comfort of use of the baler and its easy intuitive operation. Advantages of the HSM V-Press 605 baler: - Compact size - contributes to space saving. - Crushing force of 57 kN (approx. 6 tonnes) - allows bales of up to 70 kg with dimensions of 80 x 60 x 60 cm to be formed. - Low noise level - 60.1 dB (A) - Material support claws - increases loading volume and therefore increases baling capacity. - Mechanical ejector - makes bale removal easier. - Large loading aperture - increases user comfort. - Quick and easy assembly. The offer concerns the HSM V-Press 605 waste paper baler: - Code produkt : MTP004168 - Product condition: used - Year of manufacture : 2018 - Model: V-Press 605 - Width: 119 cm Rcodswcpvaspfx Ah Uok - Depth: 81.5 cm - Height: 198 cm - Weight: 485 kg - Power: 1500 w - Voltage: 400 v Net price : €3499.00 each * I have large quantities, prices can be negotiated for larger orders. * Transport throughout Europe possible. * The above offer does not include transport costs. * Location: Chmielów/Tarnobrzeg, Poland.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Bale Size: 400mm x 400mm x... 2. Container Dimensions (Width x Length x Height): 1.000mm x 2.000mm x 800mm 3. Capacity: 4 tons/hour (Steel), 5 tons/hour (Copper), 2 tons/hour (Aluminium) 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons Rodpfodfc Iyex Ah Ueck 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 210 tons 8. Maximum Working Pressure: 300 bars 9. Electric Motor: 37 kW 10. Machine Dimensions (Width x Length x Height): 3.400 mm x 6.800 mm x 3.000 mm 11. Machine Weight: 18.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Compressive force 548 kN The size of the loading opening is 1,195 x 650 mm Bale weight up to 480 kg depending on material Binding with 4 x strapping band or 4 x wire Bale size 1,200 x 780 x max. 1,200 mm Dimensions 1,797 x 1,062 x 2,985 mm Rcedpfx Aottal Ajh Uok The weight of the equipment is 2,030 kg

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Bale Size: 500mm x 500mm x... 2. Container Dimensions (Width x Length x Height): 2.000mm x 2.500mm x 1.100mm 3. Capacity: 15-20 tons/hour (steel) 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 300 tons 8. Maximum Working Pressure: 300 bars 9. Electric Motor: 2 x 75 kW = 150 kW 10. Machine Dimensions (Width x Length x Height): 10.000 mm x 10.000 mm x 4.000 mm 11. Machine Weight: 55.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. Rodpfxogwa T Ro Ah Ueck 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects.

Condition: good (used), Year of construction: 2013, Compressive force 548 kN The size of the loading opening is 1,195 x 650 mm Bale weight up to 480 kg depending on material Rcsdpfxsttav Ne Ah Ujk Binding with 4 x strapping band or 4 x wire Bale size 1,200 x 780 x max. 1,200 mm Dimensions 1,797 x 1,062 x 2,985 mm Bodhzadl7zw The weight of the equipment is 2,030 kg

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: THE MACHINE WILL BE BRAND NEW The compression chamber walls are covered with HARDOX material for long-term life-cycle and friction resistance. A hydraulic Oil Cooling system is implemented for efficiency in hot climate conditions. Cylinder Rods are induction-hardened and chrome-plated. Pumps and valves of hydraulic systems are from worldwide reputable brands such as PARKER, and BOSCH-REXROTH. The machine is fully automatic by PLC control. It is easy to use with the help of the touch screen. All electrical and electronic parts are by SCHNEIDER and SIEMENS Brands. The machine is CE-certified. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. Machine will be under Aymas Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours. SEE THE TECHNICAL DESCRIPTION BELOW Rcedpfx Asdfcqaoh Uek Bale Size 400mm x 400mm x... Bale Weight 120-180 kg (Steel), 50-80 kg (Aluminium),150-200 kg (Copper) Press Box Dimensions (Width x Length x Height): 1.000mm x 2.700mm x 900mm Loading Bunker Dimensions (Width x Length x Height): 1.650mm x 2.300mm x 800mm Feeding Opening: 1.000mm x 1.600mm Capacity*

Condition: good (used), Manufacturer: Comp Rodpfsh Eic Aox Ah Ueck Tip: SB5 Engine: 2,2 KW Cylinder stroke length: 500 mm Chamber size: 500 x 350 x 400 mm

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: THE MACHINE WILL BE BRAND NEW Rcsdpfx Aod Iya Noh Usk The compression chamber walls are covered with HARDOX material for long-term life-cycle and friction resistance. A hydraulic Oil Cooling system is implemented for efficiency in hot climate conditions. Cylinder Rods are induction-hardened and chrome-plated. Pumps and valves of hydraulic systems are from worldwide reputable brands such as PARKER, and BOSCH-REXROTH. The machine is fully automatic by PLC control. It is easy to use with the help of the touch screen. All electrical and electronic parts are by SCHNEIDER and SIEMENS Brands. The machine is CE-certified. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. Machine will be under AYMAS Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours. SEE THE TECHNICAL DESCRIPTION BELOW Bale Size 400mm x 400mm x... Bale Weight 100-180 kg (Steel), 40-100 kg (Aluminium),120-180 kg (Copper) Press Box Dimensions (Width x Length x Height): 1.000mm x 2.600mm x 900mm Loading Bunker Dimensions (Width x Length x Height): 1.500mm x 2.200mm x 650mm Feeding Opening: 1.000mm x 1.600mm Capacity*

Condition: used, mileage: 285,700 km, power: 375 kW (509.86 HP), first registration: 03/2023, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, wheelbase: 3,700 mm, next inspection (TÜV): 03/2026, brakes: retarder, gearing type: automatic, suspension: steel-air, front tire size: 315/70 R 22,5, rear tire size: 315/70 R 22,5, Equipment: air conditioning, airbag, navigation system, parking heater, Mercedes-Benz Actros 5 L-cab BigSpace, flat floor, power take-off, single auxiliary drive shaft below upper frame edge, 2 x fuel tanks 820L + 290L + 90L AdBlue, secondary oil retarder, adaptive cruise control, driver's air-suspended comfort seat with massage function, central locking, upper and lower comfort beds, leather steering wheel, driver's airbag, navigation system, auxiliary heater, electric stand air conditioning, refrigerator. Safety Package, Sight Package, Climate Package, ADR Package, Media Package, Economy Package, Driving Package, Comfort Package. V6R body type: Tank truck, hazardous goods certified. Air pressure gun, LED headlights, liquid discharge compressor with piping and pressure gauge: Gardner Denver DRUM, GD175 compressor. ATS performance warranty per terms and conditions, 3 years/450,000 km. 2 units available!! Sale exclusively to commercial customers, with all warranties excluded. Subject to errors and prior sale. Redoxwlq Hjpfx Ah Ujck

Condition: used, This listing is for the Big Neat. F3-XIT Safety Cabinet The unit is in full working condition and is ready for immediate use The Bigneat F3‑XIT is a benchtop powder weighing safety cabinet manufactured by Bigneat, tailored to protect operators from exposure to dust and particulates while handling and weighing fine powders. It features a compact footprint and excellent visibility through its acrylic enclosure, ideal for precision work. MedicalExpo DirectIndustry Rcodpexhff Sofx Ah Ujk Key Features: Compact design with great all-around visibility, available in two access styles: F3‑XIT‑D: Hinged access flap. F3‑XIT‑S: Corner “tear drop” access. Recirculating HEPA filtration, including a pre-filter and HEPA filter that removes particles down to 0.3 µm with 99.997% efficiency, returning clean air back into the lab. Balanced airflow: Pre-set to a capture velocity of approximately 0.35 m/s, proven to offer both effective containment and stable weighing condition