Used Baler for sale (229)

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,250 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, power: 22 kW (29.91 HP), year of last overhaul: 2025, volume flow: 530 m³/h, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the whirling unit replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Holhsy R Npiocdw Nenl Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 13,209 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,250 mm, filling opening length: 1,050 mm, bale width: 100 mm, bale height: 700 mm, bale weight: 500 kg, overall weight: 8,500 kg, oil tank capacity: 400 l, power: 15 kW (20.39 HP), year of last overhaul: 2026, volume flow: 108 m³/h, Technical data baler: Manufacturer according to type plate BRAMIDAN (original manufacturer Presto GmbH & Co. KG) Type HC 50 (corresponds to the Presto HPK 50) Year of manufacture 2007 Operating hours 13,209 hours, as of March 2026 Number of bales pressed: 23,379 bales Pressing force 50 tonnes Specific pressing force 650 kN/m² Feed chute dimensions 1250 x 1050 mm (L x W) Filling volume 0.96 cm³ Theoretical cycle time 32 seconds Theoretical throughput capacity 108 m³/hour Bale dimensions 1100 x 700 mm (w x h) length variable Drive power 15 kW Power consumption, total in 50 A Tying 4-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm approx. 3.1 t/hour Bulk weight of 60 kg/cbm approx. 4.5 tonnes/hour Bulk weight of 100 kg/cbm approx. 7.2 tonnes/hour Bale weights with a bale length of approx. 1.2 m up to 500 kg, depending on material Hydraulic oil tank capacity 400 litres PLC control Siemens S7-200 Effective transport dimensions excluding baler 6850 x 1950 x 2650 mm (l x w x h) Transport weight of press 8.5 tonnes Condition of the baler: The press was used in a production facility exclusively for pressing cardboard and was regularly serviced. With only 13,209 operating hours, the machine has seen little use. The press was partially overhauled in our workshop and then tested. The following overhaul work was carried out: Machine cleaned Bale retainer made operational and lubricated Helhey R Npcocdw Nsnl Light barrier replaced Twisting unit completely dismantled, broken down into individual parts, all bearings replaced, all plastic glides replaced, lubricated, chain tension adjusted Knife and counter knife dismantled, sharpened, reassembled Knife gap readjusted General maintenance work carried out and lubricated Scope of delivery: 1 baler with wire coil boxes, without wire (6850 x 1950 x 2650 mm) 1 bale chute (5100 x 1150 x 450 mm) 1 floor-mounted wire coil box (1450 x 380 x 360 mm) To transport the baler, you will need a tautliner with an effective internal height of 2700 mm. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed Hnoloy R Nnfjhcdw Njl • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Colour: Grey Empty weight: 1.250 kg Price: On request - Year: 2005 Heljym Uxtjhcdw Nsnl - Documentation available: No - CE certificate present: No - Serial number: 307 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Colour: Grey Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No - CE marking present: Yes Holhsyrtcuocdw Nenl - CE certificate present: No - Serial number: 308 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders Hnelhcsvq Rtkjdw Nsl - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. Holhcjx Dnb Usdw Nenl • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see our video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), Year of construction: 2015, bale weight: 480 kg, Brand: HSM Model: V-press 860 plus Hslhey Nizcecdw Nonl Year of manufacture: 2015 Pressing force: 418 kN Voltage: 400 V Max. bale weight: 480 kg (depending on material) Bale dimensions: 120 x 120 x 78 cm Machine weight: 2083 kg Machine dimensions: 180 x 125 x 298.5 cm Feed opening dimensions: 120 x 65 cm Condition: Very good! Function tested. Video of the machine in operation available upon request. FLITS Rental & Sales service: With every machine, we provide a bundle of tying wire (120 wires). Need more bundles? Request a quotation without obligation.

Condition: ready for operation (used), Year of construction: 2009, bale weight: 550 kg, total width: 1,570 mm, total height: 2,985 mm, overall weight: 2,403 kg, total length: 1,800 mm, filling opening width: 1,195 mm, filling opening length: 65 mm, bale width: 110 mm, bale length: 120 mm, bale height: 120 mm, transport height: 225 mm, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Holoy Iwi Eohcdw Njnl Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 x 65 cm Condition: very good! Video of machine in operation available on request.

Condition: used, Year of construction: 2008, functionality: fully functional, machine/vehicle number: 58900538, input voltage: 380 V, total width: 1,200 mm, total height: 2,300 mm, overall weight: 470 kg, total length: 850 mm, filling opening width: 830 mm, bale width: 830 mm, bale length: 600 mm, bale height: 650 mm, opening width: 830 mm, transport height: 2,300 mm, Machine fully functional, but the press plate is deformed and needs to be straightened (see photo). The machine is sold together with strapping bands for bundling the bales and a sack truck for transporting the bales. Pick-up only, no delivery and no warranty. Hnolhsy Hlg Njcdw Nol

Condition: good (used), Year of construction: 2002, functionality: fully functional, Vertical baler HSM VL 600, year of manufacture 2002 Technical specifications: Manufacturer: HSM Model: HSM VL 600 Year of manufacture: 2002 Pressing force: 60 t Drive power: 7.5 kW Cycle time (idle): 37 s Filling height: 1130 mm Feed opening: 1150 x 735 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Machine weight: 3575 kg Materials: Suitable for paper, cardboard, film, car tyres The baler is in good condition and has been inspected and tested. A demonstration video is available on our website or YouTube channel. Operating manual and CE declaration are included. Inspection, including under power, is possible at any time by appointment. Material tests with your own materials can be arranged on request and for a service fee. Hslhcdoyz Sa Sow Nonl Please note: All technical details are based on information provided by the manufacturer. We do not accept any liability for the specifications or possible errors. This offer is subject to change, prior sale reserved, and may be withdrawn at any time. Inspections are available by arrangement. Sale is ex works, without warranty or guarantee, and against advance payment only.

Condition: used, Year of construction: 1983, total width: 750 mm, total height: 900 mm, total length: 2,400 mm, Empty weight: 500 kg Hnolhcdsxalyyew Nel - Year: 1983 - Documentation available: No - CE certificate present: No - Transport dimensions: 2400mm x 750mm x 900mm (l x w x h) - Transport weight [kg]: 500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: PVF468787, pressing force: 30 t, input voltage: 400 V, bale weight: 300 kg, total width: 1,775 mm, total height: 3,225 mm, overall weight: 1,570 kg, total length: 1,025 mm, filling opening width: 1,200 mm, filling opening length: 560 mm, noise level: 63 dB, bale width: 1,200 mm, bale length: 800 mm, bale height: 950 mm, transport height: 2,300 mm, electrical fuse: 16 A, Used BRAMIN B30 plastic/cardboard baler in very good condition and ready for use. Baler type B30 VD/HS with sliding door and high-speed, including BRA-IN Pressing force: 30 t Feed opening (W x H): 1200 x 560 mm Electric drive: 400 V / 4.0 kW / 16 A Noise level approx.: 62-64 dB Cycle time: 35 sec. High press chamber: 1560 mm Long piston stroke: 750 mm Dimensions (W x D x H): 1775 x 1025 x 3225 mm Transport height approx.: 2770 mm Machine weight approx.: 1570 kg Bale size (W x D x H): 1200 x 800 x 950 mm Bale weight approx.: 280-400 kg (depending on material) Hnolhcjy Nncledw Nsl Sale only to commercial customers, warranty excluded.

Condition: new, Year of construction: 2022, functionality: fully functional, machine/vehicle number: Machinenummer 230067.020, pressing force: 60 t, power: 45 kW (61.18 HP), operating pressure: 250 bar, Bollegraaf Recycling Solutions, the original manufacturer of this mobile Bollegraaf baler, hereby offers the following machine(s) FOR RENT ONLY: Year of construction: 2022 Weight excl trailer: 22.000 kg Mobile Baler Volume capacity m3/hr max. 365 334 321 301 Volume weight kg/m3 max. 15 30 50 80 Weight capacity T/hr max. 5.5 10 16 24 Bale weight 400 – 800 kg, depending on S.G. of material and bale length Bale length - adjustable Bale height - 720 mm Bale width - 1100 m Filling opening - 1100 mm x 1320 mm Max. size supply - 1500 mm x 1200 mm Pressure force ram - max 60 tonf. Pressure force pre-press flap - max 25 tonnes Cycle time - 18 seconds Hnsloh I T Ibshcdw Nel Motor - 45 kW Motor Twistomat - 2.2 kW Motor counter pressure pump - 1.1 kW

Condition: good (used), Year of construction: 2001, functionality: fully functional, KAMPWERTH SHD 1600 horizontal baler, incl. 3 interchangeable containers 48000x2800x3000 Paper baler // Waste baler // Refuse baler Baler, 1 unit • Type: Kampwerth SHD 1600 • Year of manufacture: 2001 • Unladen weight: 3,500 kg • 15 kW • Dimensions: 5000x2300x3700 mm (disassembled for transport) Container box for baler, 3 units • Year of manufacture: 2001 Hjljxm Skrehcdw Nonl • Volume: 28 m³ • Unladen weight: 3,100 kg • Filling weight: 12,000 kg • Dimensions: 7000x2400 mm Location: Bielefeld

Condition: ready for operation (used), Strautmann PP 1207 Hnslhjra Aq Decdw Nsl Pressure force 58 tons Baler weight from 400-500 kg depending on material 4KW engine Baler format (LxWxH): 1200 x 700 x 800 mm Feed opening: 1145 x 430 mm External dimensions (LxWxH): 1844 x 1067 x 2868 mm Feed opening: 1145 x 430 mm Transport height: 2500 mm baler weight approx. 2300 kg

Condition: good (used), Manufacturer: Mil-tek Model: 205 TS Machine type: Plastic press / Film press Operating pressure: 8 bar Test pressure: 11 bar Material container: 20 l Drive: pneumatic CE marking: present Hjlhcdwoyx Skrs Njnl Quantity: 4

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Drive power: 31.5 kW Pressing force: 60 t Bale weight (depending on material): 350–600 kg Hjlhov Amw Njcdw Nsnl Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Pressing/cycle time: 13/24 s Machine weight: 7000 kg

Condition: excellent (used), Manufacturer: Strautmann Model: PP 1207 Plus Bale size (LxWxH): 1200 x 1100 x 730 mm Bale weight: approx. 400 - 500 kg Hnslhov Aiymscdw Nsl External dimensions (LxWxH): 1850 x 1047 x 3079 mm Transport height: 2500 mm Filling opening: 1190 x 600 mm Pressing force: 59 tons / 580 kN Throughput: 1 - 2 bales/hour Number of ties: 4 Press weight: 2300 kg Power supply: 400 V / 50 Hz Power consumption: 4 kW Installation location: covered indoor/outdoor Noise level: less than 80 dB(A) Year of manufacture: 2003-2005 I also have Strautmann PP 1207 balers from 2009-2011, price 5,500 EUR Also available: Strautmann PP 1208 balers from 2014-2015 Strautmann AutoLoadBaler year 2018, price 7,500 EUR

Condition: excellent (used), functionality: fully functional, pressing force: 3 t, Orwak 5070 baler in perfect working condition. Fully serviced, new oil. Fully equipped – strap holders, straps, hook, bale trolley. Hnjlhcdjy Sk H Ssw Njl

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, pressing force: 26 t, Orwak 3325 baler in perfect working order. Fully serviced, new oil. Fully equipped. Comes with additional parts for wire tying. Helhjy Sk Atocdw Nenl

Condition: excellent (used), Baler Hsm V-Press 825 plus Pressing force: 250 kN Drive power: 4 kW Cycle time: 39 s Loading height: 958 mm Loading opening width x height: 1195 x 530 mm Bale length x width x height: 1200 x 780 x 700 mm Hslhcdov Akcijw Nsnl Bale length x width x height: 1200 x 780 x 700 mm Machine width x depth x height: 1700 x 1046 x 2370 mm Machine weight: 1063 kg Type of consumables: strapping tape Compressed material: foil, mixed paper, cardboard, die-cutter waste, clothing Years 2012-2014 price 6000eur Baler Hsm V- Pres 825 pro 2019-2021 costs 9,000eur

Condition: ready for operation (used), Model: HSM V-press 1160 plus baler Pressing force (kN): 532 Bale weight depending on material: up to 550 kg Max. bale size (mm): 1200x1100x1000-1200 Dimensions L x W x H (mm): 1780x1150x2985 Power (kW): 7.5 Hsljra Nyushcdw Nenl Weight (kg): 2300 Year 2007-2010, price: 5800 EUR Year 2011-2013, price: 6000 EUR YEAR 2018 COSTS 6000 EUR We also have HSM V-press 1160 max balers from 2014-2015 available.

Condition: used, Year of construction: 2006, functionality: fully functional, Baler press for bundles approx. 400 kg. Manufacturer: HSM Model: HL 3521 Year of production: 2006 Condition: good Machine has undergone major service. Oil pump replaced. Oil cylinders refurbished. After agreement, can be sold and shipped immediately. Hnslhcdey A Hu How Njl

Condition: reconditioned (used), Year of construction: 2005, functionality: fully functional, pressing force: 90 t, filling opening width: 1,620 mm, filling opening length: 972 mm, bale width: 720 mm, bale height: 1,100 mm, bale weight: 600 kg, overall weight: 32,000 kg, pressure: 300 bar, power: 110 kW (149.56 HP), BOA baler with double pre-press flaps available in fully refurbished condition. The machine is located at our workshop in Almelo and can be inspected by appointment. If required, a matching (new) conveyor belt can be produced. The machine is perfectly suited for baling various materials such as cardboard, paper, plastics, car tires, and RDF. The machine is equipped with a so-called refu-ram. This is ideal for baling materials such as plastic bottles and/or shredded RDF. Technical specifications: Drive: 2x 55 kW Pressing force: 90 tons Bale dimensions: 1100 x 720 mm Hnslhcdjxbc U Djw Nsl Bale weight: approx. 600 kg (depending on material) Number of tying wires: 5 vertical