Used Blow Moulding Machine for sale (65,721)

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams Lhodpfxog Ailcs Ah Son 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: used, Stretch blow molding machine by Etek ISBM line = Injection stretch blow molding Stretch blow molding machine for single-use PET bottles made from PET preforms Stretch blow molding machine for production using the rotary process Manufacturer: ETEK / GF-Industries, Type Supra 800 sv 1 Lhedpskucxljfx Ah Son Serial number: 22000225 Year of manufacture: 2012 Power: 90 kW Mains connection: 400 volts, 50 Hz Weight: approximately 6000 kg In like-new condition

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, ID BYP01 We sell a used Chinese - PP melt-blown fabric extrusion line for melt blown, make: Zhangjiagang Sevenstars Machinery Co., Ltd., MFG 2020. It was used for a short time. excellent condition. All EU import duties have been paid. Output max 400 kg per 24 hours. General description: 1. Product size: PP melt blown fabric with width at 600mm (after trimming 17m*3) 2. Main Material: PP compounding material 3. Extruder type: SJ65/33 single screw extruder 4. Output capacity: 350-400kg/24hour 5. Electric power supply: 3phase, 380V; 50Hz 6. Additional equipment: • Vacuum feeder • Raw material dryer • Mesh manual filter • T-mould for melt blown fabric • Static electrical discharge equipment • Belt type forming 850mm • Collecting device • Winder and slitting Model L/D Output Speed of Screw Rotationl Power Center Height SJ-65 10-33 80-150kg/h 20-120r/min 18.5kw 1000mm This line contains the following machines: Automacic vacuum loader ZJ-400 and hopper dryer make RHONG model RDM-25, MFG 2020; Single screw extruder, model SJ65/33, MFG 2020; Heating oven for hot air, model HJGF101-4, MFG 2020; Extrusion T-mold, model: SUS630, made in Japan, MFG 2020; Forming device, MFG 2020; Winder & slitting system, MFG 2020; Oil free air compressor, MFG 2020; The PP melt blown nonwoven production line is a polymer melt extruded from a screw extruder. The polymer is extremely stretched by high-speed hot air or other means to form very fine short fibers, which are aggregated to A web is formed on a roller or a screen curtain, and is finally reinforced by self-adhesion or thermal bonding. Its unique properties are widely used in mask filter materials, thermal insulation filling materials, medical health materials, wiping materials, etc. The finished product can pass the N95 standard as the core material of the mask. Process of melt blown nonwoven production line Polymer preparation --- Melt extrusion --- Metering pump --- Melt blown die head assembly --- Solution thin-flow drawing --- Fibber cooling --- Auxiliary network --- Electrostatic electret --- Reinforced finished product. Melt-blown cloth is produced by melt-blown process. The equipment mainly includes: screw extruder, melt pump, screen changer, melt-blown device, winding device, air system (hot air blower and heater), etc. The function of the screw extruder is to melt the slice material; the role of the melt pump is to accurately measure, control the output and the fineness of the fiber, and continuously and evenly transfer the melt to the spinneret. The function of the screen changer is to filter out impurities in the melt so as not to block the spinneret holes. The function of the winding device is to pack the melt blown cloth into rolls. The function of the air system (hot air blower and heater) is to provide the temperature and pressure of the hot air used in the drawing of the spinning air stream. Ljdpfxouiq Dhs Ah Sjhn Price Euro 39.200 Euro + VAT, negotiable, FCA: Oradea / Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment AC ARCOR - multiBlow2 - 2017 Speed: 1,5L - 6000 Lhjdpsquuvrofx Ah Sen Cavities: 4 Formats: 0,1 - 3,0L AUXILARY EQUIP 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw 3. Receiver tank - Low pressure - MAX 16Bar 4. Receiver tank - High pressure - MAX 45Bar

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 13-13, The BLOMAX 4 Blowmoulding machine is of the model 13-13. The machine has no defects and operates in excellent condition with full functionality. Power : 400V/150A/60000W Ljdpfet Akgwsx Ah Sohn Year of construction : 2000

Condition: good (used), Year of construction: 1998, operating hours: 89,340 h, functionality: fully functional, screw diameter: 90 mm, overall weight: 16,000 kg, clamping force: 650 kN, total width: 2,750 mm, total length: 5,600 mm, total height: 3,200 mm, Manufacturer: Sterling Model: 15 LBS Year of manufacture: 1998 Operating hours: 89,340 h Closing force: 650 kN Screw diameter: 90 mm Lodezfxwispfx Ah Sshn BM Sterling APV, year of manufacture 1998 Complete control system replacement in 2008 with MACO-sys 6000, carried out by Davies-Standard LTD PRICE REDUCTION OF 30%!!! Net price: from 45,000 EUR to 31,500 EUR!!!

Condition: like new (used), Year of construction: 2022, operating hours: 200 h, functionality: fully functional, screw diameter: 70 mm, overall weight: 600 kg, clamping force: 80 kN, total width: 2,800 mm, total length: 4,000 mm, total height: 2,260 mm, Main Features: 1. Computer Control System (PLC) – Japanese Mitsubishi PLC 2. Electrical Cabinet – All electrical components are sourced from globally renowned brands, ensuring quality and stability. 3. Touch Screen – Innovation computer control system 4. Advanced Hydraulic Cylinder from Germany 5. Linear Guideway 6. ABB Inverter from Switzerland & Rexroth from Germany 7. Large Diameter Galvanized Steel Pipes 8. Electric Lifting Platform 9. Ceramic Heater 10. Hydraulic System & Valve Connections – From Yuken Industry Technical Specifications: • Suitable Material: PE, PP, and others • Max Volume: 6 L • Production Capacity: 170-260 pcs/h • Dimensions: 4.0 × 2.26 × 2.8 m • Weight: 6T Plasticization System: • Reducer: Hard finishing, high strength, low noise • Screw: Ø 70 mm, L/D ratio 24, 38CrMoALA, cooling system available • Plasticization Capacity: 100 kg/h (HDPE) • Heating Zones: 3-4 aluminum heaters, automatic heating • Heating Power: 12 kW/h • Extruder Motor: Three-phase asynchronous motor (380V, 50HZ) • Cooling Fan: 4 zones, automatic cooling Extrusion System: • Material: High-grade alloy steel, central feeding • Number of Die Heads: 1 • Max Die Mouth Diameter: Ø 160 mm • Heating Zones: 4, stainless steel heating cycle • Heating Power: 5-7 kW Clamping System: • Features: High strength, rigidity, central mold locking, stable mold opening & closing • Clamping Force: 80KN • Template Distance Adjustment: 170-520 mm • Max Mold Size: 380 × 420 mm Electric System: Lhjdpfx Ahsv Iflpo Son • Automatic Monitoring, Fault Alarms, Auto Counting, Auxiliary Functions • Control Interface: Touchscreen with self-diagnosis alarm system • Temperature Control: Automatic temperature control module • Motion Control: Inovance (Chinese/English version) Hydraulic System: • Features: Multi-functional integrated hydraulic block, proportional control, high efficiency • Oil Pump Motor: Three-phase asynchronous motor (380V/220V, 50/60HZ) • Oil Pump: Imported double pump • Valves: Imported oil pump valves and connections • Oil Pipes: Double-layer wear-resistant • System Pressure: 60 kg/cm² • Cooling System: Separate water cooling cycle, oil cooler Pneumatic System: • Brand: Taiwan AIRTAC pneumatic system • Air Pressure: 0.6 MPa • Air Displacement: 0.8 m³/min • Electromagnetic Valve: Taiwan AIRTAC Main Components: Electronic Parts: • PLC Control System: MITSUBISHI from Japan • Touch Screen: INOVANCE • Temperature Controller: HUICHUAN • Auxiliary Relay: OMRON • Contactor: Schneider from France • Electric Motor: Three-phase 380V • Power Source: TAIWAN MEANWELL • Transducer: ABB from SWITZERLAND Hydraulic Parts: • Oil Pump: TAIWAN HIGH-TECH • Valve: YUKEN • Oil Pump and Connection: YUKEN • Sealed Part: HALLITE Air Control System: • Cylinder: AIRTAC • Air Valve: AIRTAC This blow molding injection machine was purchased directly from a factory in China for a specific project that was never realized. The machine was used for only one month. Location: Siemianowice Slaskie, Poland We also have peripheral equipment available for sale, such as: • 5 HP AIR COOLING SYSTEM • Auto Loading • 150 kg Color Mixer • Scraps Crusher

Condition: used, The Mafell HIT-M zero-joint edgebanding machine applies edging material using zero-joint technology to straight, bevelled and free-form workpiece edges. The edging is fed in automatically and bonded to the functional layer of the edging material by means of heat; the BAT-V worktable assists with the guidance and positioning of workpieces in stationary applications. Systainer labelling: HIT-M 65 Type plate labelling: HIT-M-2750 Technical data: - Edge height: 10–65 mm - Edge thickness: 0.4–3.0 mm Lsdpj Ad D Uhsfx Ah Sjhn - Inner radius: min. 22 mm

Condition: excellent (used), Year of construction: 2013, operating hours: 200 h, functionality: fully functional, screw diameter: 65 mm, overall weight: 9,000 kg, clamping force: 785 kN, total width: 1,800 mm, total length: 4,500 mm, total height: 3,000 mm, power: 0.045 kW (0.06 HP), We offer for sale a slightly used injection blow moulding machine in excellent condition. It is connected and fully operational for demonstration purposes. We can also offer several ready-made molds for canisters and lamp shades. The machine is designed for use with PMMA, PC, PP, and PE resins. Lhodethk Rzspfx Ah Ssn

Condition: good (used), Year of construction: 1994, functionality: fully functional, Manufacturer: s.p.a magic m.p. Lhedpfoxxp Tbex Ah Son Type: MGL2D This blow molding machine is in full working order. It is still in production and can be inspected after scheduling an appointment. Upon request, I can also send videos. PRICE REDUCTION OF 30%! PRICE: REDUCED FROM 19,000 TO 13,300 EUR!

Condition: ready for operation (used), Year of construction: 2010, operating hours: 55,000 h, functionality: fully functional, clamping force: 5,000 kN, screw diameter: 90 mm, Clamping force 5000 kN Lhedpfx Ahjz I Dvyo Sjn Mould opening force, max. 279 kN Travel force movable platen opening 137,1 kN Travel force movable platen closing 116,8 kN Size of mould platens (h x v) 1370 x 1200 mm Distance between tie bars (h x v) 1000 x 800 mm Mould opening stroke 1170 mm Mould height min 480 mm Max. daylight 1650 mm Hydraulic ejector - stroke 250 mm Ejector force 95 kN Injection unit: Screw diameter 90 mm Ls/D ratio 20 Injection pressure 1839 bar Stroke volume 2290 ccm Shot weight (PS) 2084 gr. Injection rate 604 ccm/s Screw speed 195 1/min Plasticising rate max. 134,2 g/s Nozzle pressure 129,4 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 44 kW Adjustable barrel heating zones 7 Reservoir capacity 1175 ltr. Dimensions and weights: Dimensions of the machine ca. 8,00 x 2,52 x 2,40 m Total machine weight 28800 kg Max. mould weight 7900 kg Accessories: - Anti vibration pads Additional Options: - 1 x air valve - 2 x core pull on fix plate - 2 x core pulls on movable plate - 8 x hotrunner controller - Robot interface according to Euromap 67

Condition: good (used), Year of construction: 2017, Traverses X Y Z: 355 x 305 x 455mm, Table 457 x 381mm, Spindle speed 50 – 6000 rpm, Spindle taper BT30, Spindle Motor 3Hp, Lhjdpfx Asz St Hwoh Ssn Prototrak TMX Control, 8 Station ATC, coolant, Low Volt light.

Condition: ready for operation (used), Year of construction: 2010, operating hours: 43,000 h, functionality: fully functional, clamping force: 6,500 kN, screw diameter: 80 mm, Clamping force 6500 kN Mould opening force, max. 346 kN Travel force movable platen opening 169 kN Travel force movable platen closing 144 kN Size of mould platens (h x v) 1510 x 1370 mm Distance between tie bars (h x v) 1000 x 930 mm Lhedpfxez N E Eys Ah Ssn Mould opening stroke 1150 mm Mould height min 600 mm Max. daylight 1750 mm Hydraulic ejector - stroke 250 mm Ejector force 95 / 48 kN Injection unit: Screw diameter 80 mm Ls/D ratio 22,5 Injection pressure 2205 bar Stroke volume 1810 ccm Shot weight (PS) 1647 gr. Injection rate 498 ccm/s Screw speed 195 1/min Plasticising rate max. 106 g/s Nozzle pressure 129 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 44 kW Adjustable barrel heating zones 7 Dimensions and weights: Dimensions of the machine ca. 8,50 x 3,00 x 2,70 m Total machine weight 35000 kg Accessories: - Anti vibration pads - 10-fold water regulator - Krauss Maffei Robot LRX250 X: 900 mm Servo Y: 1000/1000 mm Servo Z: 3500 mm Servo C: 0 - 90 ° Additional Options: - 2 x core pulls on movable plate - 2 x core pulls on fix plate - Robot interface according to Euromap 67 - 6 x hydraulic sequentional valves - 12 x hotrunner controller - 1 x Air valve

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, IN EXCELLENT CONDITION - ORIGINAL PAINTWORK XYZ SMX 3500 CNC TURRET MILL Lhsdpfx Aez Eh Egsh Sjn PROTO TRAK CONTROL 3 AXIS CONTROL TABLE SIZE 1370 X 356 MM TRAVELS - X 770 / Y AXIS 500 / Z 500 MM 40 TAPER SPINDLE QUILL DIA 100 MM AIR DRAW BAR SPINDLE SPEED 40 - 5000 RPM TABLE GUARDS WEIGHT 2.4 TONS THERE IS ONE TOOL IN THE SPINDLE THAT WILL GO WITH

Condition: good (used), Year of construction: 2016, Traverses X Y Z: 710 x 450 x 510mm, Table size 760mm x 430mm, table load 500 kgs, spindle speed 8000rpm, spindle motor power 20Hp, Siemens 828D Control with Shopmill, rapid feed XYZ axis 20m/min, Spindle taper BT40, Lhedpfx Ahoz R Rbdj Son 24 station ATC.

Condition: excellent (used), Year of construction: 2017, XYZ 2000 Turret Milling Machine (2017) (Ex College) 3 Axis Newhall DRO (X, Y & Knee) Lhsdpfx Ahoxxb Rrs Sen Spindle Taper R8 Spindle speeds to 500 – 4200 rev/min Table Size 1270 x 254mm Table Travel: X - 812mm Y - 406mm Knee Travel: Z - 406mm Quill Travel Z - 127mm For sale with Jet Machinery Ltd Jet Machinery Stock No: #79047 Machine Serial Number: 12907 Cost: £9,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: excellent (used), Year of construction: 2023, 400mm swing, 220mm max diameter, 490mm between Centres, Siemens 828 Control, 65mm bar capacity, 12 station VDI30 turret, 17kW Spindle Motor, Spindle Speed 4000rpm, 0.001 degree C axis, +/- 35mm Y axis, low volt light, coolant, Tool setter, Tailstock, swarf conveyor Lhodpjz Srv Defx Ah Sjn

Condition: excellent (used), Year of construction: 2021, XYZ RMX 3500 3 Axis CNC Bed Milling Machine ProtoTRAK RMX Control YOM 2021 Spindle: 5HP – Programmable 40 – 5000rpm 2 Ranges 40 – 600 & 300 – 5000rpm ISO40 Quill Dia 105mm Table: 1370 x 355mm 4 0ff T Slots T Slot size 15.9mm Max load 600kgs Travel: X – 787mm Y – 508mm Head Vertical (Z) – 500mm Lhjdpfxjx D Tbme Ah Sen Quill (Z) 127mm Dims without travel – 1905 x 2069 x 2225mm Dim with travel – 2758 x 2869 x 2490mm Weight 2430Kgs Power Requirements 22A Air Requirements 6bar YOM 2021 For Sale with Jet Machinery Ltd Jet Machinery Stock Number: #78900 Machine Serial Number: RM310097 £35,000.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: used, Year of construction: 1998, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 16/16 S1 Year of manufacture 1998 Capacity: 16,000 for 1.5 L bottles and up to 19,000 bph for 0.5 L bottles Lsdpfx Ahoutni Re Sehn Installed power: 347 kW Includes 1.5 L moulds Preform feeder Chiller cooling unit Technical condition: used machine, functional until dismantled. The machine is currently dismantled, assembled in elements and prepared for transport. Full and original technical documentation.

Condition: reconditioned (used), Year of construction: 2002, functionality: fully functional, clamping force: 805 kN, screw diameter: 42 mm, injection weight: 172 g, Now fully refurbished by our team at STV Machinery in Wellingborough, Northamptonshire, is this high precision BOY 80M injection moulding machine. The BOY 80 is one of the most compact 80t clamp machines around, a great allrounder, fitted with the Procan 2 controller and 42mm diameter screw, which gives a shot weight of 179 (PS)g. Lhedpfx Ahewfpqce Sjn Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on request. We can take out the hassle and additional costs of purchasing machinery within the UK and EU. Contact us with a potential delivery address and we’ll do the rest.

Condition: like new (used), Year of construction: 1998, functionality: fully functional, Swivel spindle milling machine VEMA TFMS 2-4 in very good condition, like new; the machine comes from a correctional facility and has only been idle for the past few years; it has been used very little and operated by only one person. VEMA is a company from Northern Germany; the machine's design is similar to the KÖLLE F45 or the PANHANS 240. everything functions perfectly all bearings and guides are in good condition year of manufacture 1998 the machine has the control panel on top with a milling stop that can be adjusted on one side or completely in depth; this is possible with a handwheel in each case. For complete adjustment, there is a mechanical counter; the counter can be set to zero at any point by pressing a button, allowing the stop to be adjusted quickly and very precisely. both stop jaws can also be adjusted individually; there are also 2 mechanical counters, which allow for one-sided adjustment and also enable facing operations, for example, on a gluing profile. the milling stop can be rotated on the machine table the machine has an extra-powerful motor with 7500 watts with pneumatic spindle locking the chips can be removed very well, with 2 extraction ports 120mm with a 30mm spindle that can be adjusted steplessly from -10 to 45°; the spindle is adjusted by handwheel with a mechanical counter. with right/left rotation we will personally deliver and demonstrate the machine anywhere in Germany for 220.00 euros; this means you have no risk when purchasing. Shipping to Austria and the rest of the EU is also possible upon request. with a large table opening that can be reduced by means of various rings; this means that milling cutters with a very large diameter can also be used, and you can also mill safely with small milling cutters (the rings are included, but they are not visible in the pictures). with 3000, 6000, 4500, 7500 and 9000 rpm the spindle height adjustment is also done by handwheel; here too, there is a very precise mechanical counter for reading the height. the table is made of highly ribbed cast iron with an interchangeable spindle (a 40mm spindle can also be used) very robust and durable design; the machine was built for the most demanding milling operations and is suitable for all milling operations. optimal power transmission through belt drive Ljdo Afaugepfx Ah Sehn with instruction manual with 3-roller feed HOLZ HER ETX the feed has right/left rotation; the feed rollers are individually mounted and all are like new; it has 8 speeds the machine table is 1020mm wide and 980mm deep + 500mm wide extensions on the left and right the machine can be used immediately 380V, 7500W Weight: approx. 1000kg with all necessary safety devices; the machine is approved by the Holz-BG (German Wood and Furniture Employers' Accident Insurance Association). the machine weighs approx. 1000kg with motor protection switch against overload professional equipment, not cheap hardware store junk optimal, simple, fast and safe handling

Condition: good (used), Year of construction: 2011, operating hours: 59,000 h, functionality: fully functional, clamping force: 250 kN, screw diameter: 30 mm, clearance between the columns: 270 mm, injection pressure: 2,000 bar, total length: 3,180 mm, total width: 1,430 mm, total height: 1,850 mm, overall weight: 2,110 kg, warehouse no.: 503725 manufacturer: ARBURG type: Allrounder 270 S 250-170 controller: SELOGICA year of construction: 2011 operation hours: 59000 h technical data clamping unit clamping force: 250 kN distance between tie-bars h x v: 270 x 270 mm size of mould plates h x v: 380 x 380 mm min. mould height: 200 mm max. open daylight: 550 mm opening stroke: 350 mm ejector stroke: 100 mm ejector force: 20 kN centering diameter of moving platen: 110 mm centering diameter of fixed platen: 110 mm technical data injection unit screw diameter: 30 mm swept volume: 85 ccm injection pressure: 2000 bar screw length: 20 l/d screw torque: 250 N injection rate into the open: 96 g/s PS number of heating zones: 4 nozzle stroke: 300 mm Lhjdpfxsz Eax Eo Ah Ssn measures & weight measures of machine l x w x h: 3.18m x 1.43m x 1.85m total weight: 2110KG equipment included incl. Spruepicker screen text german screen text german core pulling hydraulically 1x Anti vibration mounts

Condition: reconditioned (used), Year of construction: 2004, clamping force: 129 kN, ejector stroke: 30 mm, total length: 27,400 mm, total width: 810 mm, total height: 1,600 mm, overall weight: 920 kg, pump power: 5,500 W, Now fully refurbished by our team at STV Machinery in Wellingborough, Northamptonshire is this high precision BOY 12A injection moulding machine. Fitted with the Procan controller and 18mm diameter screw, which gives a shot weight of 9.64 (PS)g. Lhsdpfx Ahetpw I Uo Sjn The 12A from BOY is one of the most common small moulding machines we see, it is extremely accurate while still maintaining versatility with tooling and familiar control setup. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on request. We can take out the hassle and additional costs of purchasing machinery within the UK and EU. Contact us with a potential delivery address and we’ll do the rest.

Condition: ready for operation (used), Year of construction: 2007, operating hours: 65,000 h, functionality: fully functional, clamping force: 1,300 kN, screw diameter: 45 mm, injection weight: 289 g, Clamping force 1300 kN Mould opening force, max. 70 kN Size of mould platens (h x v) 745 x 770 mm Distance between tie bars (h x v) 470 x 470 mm Mould opening stroke 600 mm Mould height min 300 mm Max. daylight 900 mm Hydraulic ejector - stroke 150 mm Ejector force 23/10 kN Injection unit: Screw diameter 45 mm Ls/D ratio 22,4 Injection pressure 2336 bar Stroke volume 318 ccm Shot weight (PS) 289 gr. Injection rate 143 ccm/s Screw speed 265 1/min Plasticising rate max. 29,3 g/s Nozzle pressure 50 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 22 kW Installed heating capacity 15,5 kW Adjustable barrel heating zones 5 Oil Reservoir capacity 400 ltr. Dimensions and weights: Dimensions of the machine ca. 5,00 x 2,00 x 2,20 m Total machine weight 8000 kg Max. mould weight 1490 kg Accessories: Lodpfx Ajzyrudoh Sjhn - Anti vibration pads - 2 x 6-fold water regulator Additional Options: - 2 x Air valves - 1 x hydr. Core pull - 12 x hotrunner controller - Robot interface according to Euromap 67 - Accumulator - 1 x pneum. core pull

Condition: ready for operation (used), Year of construction: 1970, operating hours: 1,362 h, functionality: fully functional, machine/vehicle number: 9286, planing width: 600 mm, Planer machine Kupfermühle 5 spindles: bottom / top / right and left / bottom We have produced castle floorboards with this machine, and it was operational until the end. Lsdpfx Aoyyvuwjh Sehn The machine can be demonstrated. Due to its age, it is sold without warranty or guarantee.