Used Bundle Press for sale (28,045)

Condition: new, Year of construction: 2025, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Hedpow Sgnkjfx Ag Nofn Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice

Year of construction: 2009, condition: used, comprising: 1 vacuum press with heating BÜRKLE type: M8, year of manufacture: 2009, serial no.: , dimensions (WxHxD): approx. 300x180x200 cm, 2 loading tables dimensions (WxHxD): approx. 300x100x180 cm, for alternating loading, 2 film cutters, dimensions (WxHxD): approx. 50x100x200 cm, 2 paternoster racks, dimensions (WxHxD): approx. 100x250x200 cm, with mandrels for film rolls, 1 vacuum pump Hfsdpfxexnam Rs Ag Nsn

Condition: used, Year of construction: 1987, With this roll press, you can press different materials together in a single pass. Application example: Previously, sandwich panels were bonded and pressed with this machine. Technical data: - Manufacturer: Bürkle - Type: AM - Year of manufacture: 1987 - Working width: 1,600 mm - Working height: 880 + - 20 mm - Part height 20 - 160 mm - Operating side left - Pressure cylinder from above, rubberised - Counterpressure cylinder from below, rubberised - Width of counterpressure cylinder 1,700 mm - Feed 3 m/min. - Total electrical connection - Volt/Hz 400/50 - Location in warehouse in Blomberg Hfjdpewd Nx Defx Ag Nen

Condition: ready for operation (used), Met elektrische achteraanslag Ponscapaciteit: 70 ton Dia x plaatdikte: Ø 28 x 20 mm Maximale slag: 80 mm Hfsdpfx Agoxgv E Ts Nsn 40 str / min Keeldiepte: 300 mm Werkhoogte: 1065 mm Maximale snijdikte in plaat: 20 mm Bladlengte: 455 mm 90°-snede: 130 x 130 x 13 mm 45°-snede: 90 x 90 x 10 mm Op maat gesneden rond/vierkant: 45 mm Elektromotor (vermogen): 7,5 kW Lengte: 1800 mm Diepte: 1200 mm Hoogte: 2000 mm Gewicht: 1650 kg

Condition: used, Year of construction: 1964, pressure 10 t throat 235 mm stroke ca. 400 mm stroke speed - idle stroke downwards 4,5 m/min stroke speed - idle stroke upwards 10 m/min dayligth ca. 500/600 mm table-size ca. 450 x 400 mm ram hole 32 mm total power requirement 2,2 kW weight of the machine ca. 1,5 t dimensions of the machine ca. 0,95 x 0,45 x 2,1 m Hydraulic single-column press - from a training workshop, no guarantee on UVV, with two-hand control via separate control panel. Work only with safe tools or solid shields! Machine only works in full stroke, the stroke limiter of the ram cannot be regulated because the adjustment chain needs to be repaired, so it is sold at a special price. Machine dealer with own stock of 1600 m². Hsdpfx Asvgnqfog Nsfn

Condition: good (used), functionality: fully functional, Year of construction: 2010, Used 4-meter CNC press brake from Bystronic Model: Xpert 200 4100 Year of manufacture: 2010 Capacity: 4100 x 200 tons Cybelec VisiTouch PAC CNC control (latest model) CNC controlled axes: Y1, Y2, X1, X2, R1, R2, Z1 and Z2 Hjdpfx Aexgngisg Njfn CNC hydraulic crowning Hydraulic upper clamping (RFA) Hydraulic lower clamping (WILA - 13 mm) Hydraulic flat die in lower table Automatically adjustable AKAS Fiesller laser safety system

Condition: excellent (used), Year of construction: 2013, LAMELLAR - CASE CLAMP GANNOMAT "CONCEPT 70 ECO" Hodpow Tdymefx Ag Nofn Complete in standard configuration with: Case joints. - Counter-pressure surfaces (side pressure wall, base) are 40 mm thick, coated, continuous support plates - Electrically operated adjustment of both press beams via precision trapezoidal-thread spindles (with increased lead and concentricity accuracy) and high-performance running nuts with grease reservoir. - Clamping is performed electrically using two separate worm gear motors (2 x 0.75 kW) - Pressing force: 2000 daN (kg) per press beam. - The pressing force of the press beam is electronically regulated and set via frequency converter, thus torque transmission is completely wear-free. - Pressing and adjustment speed: 25 mm/sec. - Very simple operation via 6 separate push buttons; 6 movement operations can be selected via the controller. - Freely adjustable pressing time preselection with automatic opening: 0-30 min (switchable to seconds or hours). - Working height/feeding height: 300 mm - Working dimensions: Length min: 150 mm, max: 2550 mm; Height min: 150 mm, max: 1400 mm. Depth: 700 mm 1 selector switch for variable pressing force: 1000 / 1500 / 2000 daN (kg) Machine No. 380.324 400V, 3Ph, 50Hz (2.5 kVA, 16 A) Set of machine feet for working height 500 mm Machine used: Year of construction: 2013, fully overhauled by Ganner, 6-month parts warranty Special price: ex-stock 54634 Bitburg - immediately available -

Year of construction: 2007, condition: used, comprising: 1 heated vacuum press BÜRKLE Type: BTF 1528-1400 Year of manufacture: 2007 Serial No.: 11507-20, dimensions (WxHxD): approx. 350x200x200 cm, table surface approx. 280x170 cm; 1 lifting platen table BÜRKLE Serial No.: 11507-30, with 2 support plates, dimensions (WxHxD): approx. 300x140x200 cm; 1 turning table BÜRKLE, for support plates, Serial No.: 11507-10, dimensions (WxHxD): approx. 400x320x200 cm; 1 BÜRKLE film unwinder Serial No.: 8669-71 with cutting device; 1 KRAFT paternoster storage rack Type: 810-41-00001 Year: 1991 Serial No.: 19603016, dimensions (WxHxD): approx. 220x380x150 cm; 1 BÜRKLE panel table for shaped parts, dimensions (WxHxD): approx. 350x120x180 cm; 1 film unwinder stand; 2 safety light barriers; control cabinets; 1 pressure/vacuum tank approx. 1,500 ltr.; 1 BÜRKLE terminal; 1 HP flat screen, keyboard and mouse. Supply does not include stock of coating film, the remaining material stock is to be properly decommissioned by the buyer as instructed. Hedpfx Agjxnam Do Njfn

Condition: used, Single-column hydraulic press SCHULZ Type SES 250 . 04.86.3511/3 Year of manufacture: 1986 Pressing force: 25 tons Return force: 10 tons Throat depth: 360 mm Table size: 600 x 720 mm Ram area: 500 x 500 mm Clear hole in table: Ø 100 mm Clamping pin bore: Ø 40 mm Ram stroke: 400 mm Maximum installation height: 600 mm Table height above floor: 935 / 775 mm Hydraulic tank capacity: 380 liters Drive power: 7.5 kW Power connection: 380 Volt, 50 Hz - Adjustable fixed stop in the press cylinder 180 mm, with hand crank adjustment - SICK light barrier Hedohl Npqjpfx Ag Nofn - Two-hand operation - Base made of 160 mm U-steel Space requirement (L x W x H): 1900 x 1300 x 3100 / 3260 mm Weight: 3.6 tons Good condition

Condition: used, functionality: fully functional, Year of construction: 2003, control type: NC control, controller manufacturer: Robosoft, controller model: ATS 560 NC., bending force (max.): 200 t, working width: 3,600 mm, stroke length: 200 mm, throat depth: 300 mm, distance between stands: 3,150 mm, type of crowning: manual, overall weight: 12,500 kg, power: 18.7 kW (25.42 HP), Capacity: 3600 x 200 tn. Distance between frames: 3150 mm. Stroke: 200 mm. Throat: 300 mm. Control: Robosoft ATS 560 NC. Tools: 1 set. Full length. Motor: 18,7 kW. Year: 2003 Hfsdpfjxn Shtox Ag Non Country of origin: Belgium. Size (L x W x H): 4900 x 2200 x 2650 mm. Weight: 12.500 kg. With Lazersafe ligth guard and manual crowning table.

Condition: used, pressure 6 t dayligth 180 mm spindle diameter 32 mm throat 115 mm ram stroke 90 mm table surface area 300x270 mm weight of the machine ca. 70 kg dimensions of the machine ca. 800 x 1350 mm 6 t (estimaeted) hand-operated spindle press. The machine is professionally and durably lashed. Machine dealer with own stock of 1600 m². Hfsdpfx Agjvgnnwo Nsn

Condition: excellent (used), functionality: fully functional, Year of construction: 2005, control type: CNC control, controller manufacturer: Cybelec, bending force (max.): 60 t, working width: 2,550 mm, number of axes: 8, type of crowning: CNC-controlled, pressing force: 60 t, working range: 2,550 mm, Equipment: CE marking, documentation/manual, lower tooling, safety light barrier, upper tooling, Used quality 2005 BYSTRONIC EDWARDS PEARSON PR60 x 2550 8axis cnc Press Brake for sale High specification and highly accurate Cnc downstroke pressbrake for sale – Video at the bottom of the listing running in our stock Bed length 2.5metre Year / new: 2005 Hfedpfx Aowihk Aeg Njn Model: PR60x2550 Capacity / tonnage: 60ton / 600KN Complete with quality Swiss made Cybelec MODEVA 12 CNC Control 8axis in total – Y1,Y2,X1,X2,R1,R2,Z1,Z2 – 6axis back gauge Max stroke 215mm Hydraulic crowning Hydraulic tool clamping system FIESSLER Light Guard System Associated Tooling – per photographs Fully serviced with Bystronic uk

Condition: new, Year of construction: 2025, AL-KO POWER UNIT® 300 P-BP 30 -50 Intake port : 300 mm nominal motor power : 7,5 kW / 3 Ph Voltage: 400 V / 50 Hz Maximum volume flow : 6000 m³ / h Nominal volume flow : 5.089 m³ / h Negative pressure 2.587 Pa Filter area 30 m² Dimensions (L x W x H) in mm 3.000 x 1.361 x 2.817 Briquetting capacity 30 - 50 kg / h Briquette diameter: 50 mm Weight: 1570 kg Hsdpjh D If Hjfx Ag Nsfn Machine is brand new in our STOCK - IMMEDIATELY AVAILABLE - subject to prior sale Location: 54634 Bitburg

Condition: used, Year of construction: 2016, Assembly in 2017, consisting of: unwinding and rewinding unit (unwinder/rewinder), each with SIEMENS control system including touch panel, FANUC R2000ic 210f loading robot, control unit (for print unit setup), 8 color printing units (left tower, central tower, right tower). Weight: 16/35/18 t, BST edge guiding system, AHLBRANDT surface treatment (corona station), extraction unit, 5 web tension units, web break sensor, inspection table, BST eltromat register control, serial no.: WA18911, RITTAL control cabinet, PSI electron beam unit with switching and cooling system, pressure vessel, oxygen analysis, BST eltromat web monitoring system, BST eltromat visual defect detection system, year of manufacture: 2017, platform, staircase, mounted control cabinet (for corona station), serial no.: 513783, power: 8 kW, control center (container design), various MITSUBISHI climate control units, specialized media supply (water, electricity, nitrogen, compressed air), central SIEMENS control system, safety fencing, light barriers, total weight approx. 110 t. Hedoxnafaopfx Ag Njfn

Condition: used, Hydr. differential stroke press, toggle lever hydraulic press, automatic punching press BRUDERER - LEINHAAS type AR 11-100.H Fine blanking press, knuckle-joint press Machine. No. P247 Year of construction 1991 Pressing force 100 ton (1000 kN) Installation height max. 380 mm Table surface 1100 x 700 mm Outlet hole 800 x 220 mm ram surface 690 x 315 mm Frame width 1150 mm Lateral upright width 410 mm Stroke rate 45 and 80 strokes/min. Clamping pin bore Ø 50 mm Compressed air requirement 8-10 bar Hydraulic tank capacity approx. 700 liters Motor power main drive 22 kW Mains connection 400 Volt, 50 Hz, 28 kW - 2 speed settings for the number of strokes (45 and 80 strokes/min.) - electronic cam controller BALLUFF, type Minicontroller BMC4K - electronic tool monitoring EBERLE, type PLS 509S - KISTLER press force monitoring system - table surface with 22 mm T-slots and ram surface with 14 mm T-slots - Electronic stroke counter - motorized height adjustment for the ram - central oil lubrication - Work area shielding through pneumatic opening protective screen - adjacent control cabinet and electrical cabinet - 2 oil coolers with FLUTEC cooling fan (oil-air cooling) - Electrical circuit diagram and printout of PLC program available - Two-hand operation on the machine Hsdpfjgp T Euox Ag Nefn Space requirement (control cabinet) L x W x H 700 x 700 x 2100 mm ( approx. Space requirement (electrical cabinet) L x W x H 1700 x 650 x 2100 mm Space requirement (press) L x W x H 2350 x 1700 x 3300 mm Weight of the press 8500 kg Very good condition

Condition: good (used), Year of construction: 2005, 1 used hydraulic press brake Make: Knuth Model: AHK 31160 Year of manufacture: 2005 Technical data Working length: 3000 mm Press capacity: 160 t Stroke: 175 mm Equipped with: Hfsdsxnp A Uspfx Ag Non Elgo control Foot pedal Tooling

Condition: like new (used), Year of construction: 2025, operating hours: 1 h, Super special price, as it was on display at our in-house exhibition. Operating hours: 1 Available immediately - subject to prior sale Hfodotnz Ttspfx Ag Nsn If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg

Year of construction: 2025, condition: as good as new (ex-display), Vacuum - membrane press VP - series are the ideal solution for the wood processing industry. VP 3000 is equipped with heating technology, which reduces the drying time of the adhesive so that the performance is higher. Usage possibilities: Veneers / form gluing / wrapping... Coating of different profiles (veneer, paper, plastic...) Wood bending: Production of bent and glued components The heating system is equipped with temperature control Rubber membrane 2.5 mm Table top is made of plastic 12 mm Oil-free Becker vacuum pump 25 m3/h The control system of vacuum / Tankinhalr 15 l Work surface: 3000x1500mm Heating system temperature: Max 60 degrees C Heating system: KW 4,5 Pump output: KW 0.75 Vacuum pump capacity: 25 m3/h Rubber membrane Dimensions exterior: 3100 x 1650 x 1600 mm Hfodpjdvltyjfx Ag Nsn Weight: 450 kg Location: Off the shelf 54634 Bitburg -free load-

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Lamella - carcass press with rapid traverse Technical data: Lamella carcass press from our showroom; Working range: width from 150 - 2.500mm , height from 150 - 1.400mm; depth 700mm; - lamella press beam top with 6 elements, lamella press beam side with 5 elements - lamella press beam with practice-proven tolerance compensation for tightly pressed carcass joints - Counterpressure surfaces are 40 mm thick, coated continuous support plates - The pressing force of the pressing bars is infinitely variable electronically controlled by 2 potentiometers and adjusted via frequency converter, therefore the torque transmission is absolutely wear-free. - Pressing force for horizontal press bars min. 500 daN (kg) to infinitely variable max. 2200 daN (kg) Hfodpfx Ageiidm Nj Njn - Pressing force for vertical press bars min. 300 daN (kg) to stepless max. 2200 daN (kg) - Including option: Rapid traverse speed for fast positioning of the press bars, controlled by automatic workpiece recognition with sensors in the press bars, press speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Jog mode for precise positioning of the two pressing beams e.g. for low pressing forces, drawers and carcasses 45 degrees. Simple operation via 6 separate pushbuttons, freely adjustable pressing time preselection with automatic opening, loading height 300 mm. Machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2024, Weima Briquetting Press TH 714 The TH 714 machines are designed for plants with required throughput rates of up to 150 kg/h. The stable press housing enables the production of high-strength briquettes - from materials such as wood, polystyrene, foams, light metals, paper or biomass. Numerous additional options can be implemented, e.g. oil cooling for multi-shift operation. All machines are available as left- or right-hand version. Mounting on a stable base frame ensures fast installation and makes mobile use possible. User-friendly operation thanks to Siemens PLC control In order to live up to our performance promise, we design and produce all control cabinets ourselves at our Ilsfeld site and equip them with well-known international components. This guarantees highest quality with compact design. The used PLC-control from Siemens is perfectly adapted to the requirements of the briquetting process. Hfodpfxeil Hggs Ag Nsn Impurity-resistant screw conveyor due to cardanic suspension The screw conveyor, which transports the material into the pre-compressor of the briquetting press, is suspended on a cardan joint. This prevents interfering materials from causing damage to the screw conveyor. As is so often the case, however, it always depends on the specific application which suspension is chosen. For metal applications, for example, we often recommend rigidly mounted screws. Briquette diameter (mm): 70 Throughput capacity up to (kg/h): 150*1 Hydraulic motor (kW): 11 Oil quantity (liters): 250 Weight (approx. kg): 1100 Location: Ex stock 54634 Bitburg - immediately available - subject to prior sale

Year of construction: 2025, condition: as good as new (ex-display), Vacuum - membrane press VP - Series are the optimal solution for woodworking. VP 3000 is equipped with the heating technology, which shortens the drying time of the glue, so that the efficiency is higher. Possible applications: Veneer / form gluing / wrapping... Coating of different profiles (veneer,paper, plastic...) Wood bending: production of bent and layer-glued components The heating system is equipped with temperature control Rubber membrane 2,5 mm Table top is made of plastic 12 mm Oil-free Becker vacuum pump 25 m3/h The control system of the vacuum / tank capacity 15 l working area: 3000x1500mm Heating system temperature: Max. 60 degrees C heating system: KW 4,5 Pump capacity: KW 0,75 Vacuum pump flow rate: 25 m3/h Rubber membrane Dimensions outside: 3100 x 1650 x 1600 mm Hfedpfx Asdwh E Aeg Nen Weight: 450 kg Machine is equipped with a chassis. Location: From warehouse 54634 Bitburg - free on truck -

Condition: like new (used), Year of construction: 2025, operating hours: 1 h, Super special price, as it was on display at our in-house exhibition. Operating hours: 2 Available immediately - subject to prior sale If gone - then gone Hsdpfx Agstnz Hbo Nofn Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg

Year of construction: 1985, condition: excellent (used), Edge gluing press for veneer, solid wood and plastic, model HFK 2200, for trimming edges during press time. When using heat-curing glue, we achieve pressing times of 20 to 30 seconds for veneer edges. Hfedpew Apqqofx Ag Njn Maximum working size approx.: 1,400 x 2,500 mm Heating: 1.7 kW Electro-pneumatic edge press Haug HFK 2200 for pressing edging material onto wood, with heating. 3 table extensions Swiveling work table Location: ex stock 54634 Bitburg - immediately available -

Condition: used, Year of construction: 1968, Veneer press Manufacturer: Bütfering Model: 22/11 Year of manufacture: 1968 Plate size: 2.2 x 1.1 m Note: Heating plates no longer function – therefore very inexpensive Has been used as a cold press 4 cylinders Cylinder stroke: 360 mm Hydraulic Location: ex stock 54634 Bitburg Hjdpfx Agjw Nbztj Nefn - immediately available -

Condition: new, Year of construction: 2025, AL-KO POWER UNIT® 250 P-BP Intake port : 250 mm Hfedpfx Aecdr E Ajg Nen nominal motor power : 6,5 kW / 3 Ph Voltage: 400 V / 50 Hz Maximum volume flow : 4.900 m³ / h Nominal volume flow : 3.534 m³ / h Negative pressure 2.451 Pa Filter area 22,4 m² Dimensions (L x W x H) in mm 2.305 x 1.333 x 2.609 Briquetting capacity 30 - 50 kg / h Location: Comes to stock 54634 Bitburg Subject to prior sale