Used Debut Press Hydraulic for sale (37,451)

Condition: good (used), Code: 0136 Brand: ITALPRESSE Model: FORMATIC 20.9 Hydraulic fluid membrane press Two sided lamination of veneer to panels shaped or profiled on one face and flat on the other to produce cabinet door raised panels, drawer fronts, desk tops, table tops, kitchen tops, etc. 3-D lamination of plastic foils (PVC, PPE, ABS, Transfer foil ) to panels sheped or profiled on one face to produce: cabinet doors, drawer fronts, desk tops, table tops, kitchen tops, store fixture components, room doors, etc. Platen dimensions mm 2000 x 900 Daylight mm 325 Cylinder stroke mm 325 Heating electric boiler Kw 27 Thrust ton 300 ton N° 3 thrust cylinders Hydraulic unit power Kw 5,5 Pressure control manometer Automatic pressure reset Opening timer Iodpepbvqvjfx Ag Notn Overall dimensions mm 3300 x 1400 x 2400 h Weight kg 8100

Condition: used, machine/vehicle number: 72004250751, table width: 900 mm, table length: 2,000 mm, OMET Press, 250T capacity Table 900x2,000mm Strokes per minute: 30-60 Iedpfx Agjxnzd Rs Notn Travel: 18-200mm

Condition: used, Year of construction: 1995, functionality: fully functional, pressing force: 250 t, table width: 1,600 mm, table length: 2,650 mm, overall weight: 55,000 kg, die cushion stroke: 235 mm, Hydraulic deep drawing press Wanzke GTA 250 year of construction 1995 used Technical data: Pressing force 2,500 kN ram stroke 600 mm ram speed working stroke 25 mm/s Die cushion 1,600 kN Die cushion stroke 235 mm Table clamping surface 2,650 x 1,600 mm Stroke limiting spindles 2 pcs. Damping cylinders 2 pcs. Drive power 75 kW Press dimensions approx. width 4,250 mm (without cladding) depth 2,000 mm height 5,150 mm Weight 55 to. Iodpfeup Skwox Ag Netn Table: Holes for quills in the center of the press table. From there, the other holes holes have a distance of 150 mm to the right and left There is also a hole in the middle of the press table. The hole spacing is also 150 mm. A maximum of 15 quills are possible lengthwise and 7 widthwise. possible. Quill diameter: 30 mm

Condition: used, Hydraulic Synchronizing Press, Spotting Press AGEO Type GHP 200 H6 4-Column Hydraulic Press, Tool Trial Press, Spotting Press Serial No. 21169 Year of manufacture: 1993 Pressing force: 200 tons Clearance between uprights (front): 1200 mm Upright opening (side): 650 mm Table surface: 1560 x 1010 mm Ram surface: 1560 x 1010 mm Ram stroke: 575 mm Draw cushion stroke: 300 mm Draw cushion holding force: 63 tons Draw cushion ejector force: 30 tons Max. installation height: 775 mm Table height above floor: 1000 mm Guide column Ø: 140 mm Clamping pin bore in ram: 64 mm Pressing speed: 0 to 10 mm/s, stepless Itsdpfxewva I Hs Ag Nsn Return speed: 0 to 20 mm/s, stepless Main motor power: 22 kW Control pump motor power: 5.5 kW Connection: 400 Volts, 50 Hz - Table and ram with 22 mm T-slots - Two pressure cylinders with electronic precision synchronization control - Stepless electronic stroke limitation (top and bottom with digital travel measurement and position display) - Mechanical safety support device (prevents ram from dropping due to dead weight) - Single-hand and two-hand operation - Electrical tool safety via signal contact - Pressure presetting independent of stroke (via keypad, digital pressure display) - Travel measurement system right and left via rotary encoders - Electrical control: MS-DOS PC with Ageo H v2.23 control software - Operator panel with swiveling display - Stroke movement and press force adjustable via joystick - Adjacent hydraulic power unit with electrical cabinet - Hydraulic draw cushion under the press table - Draw cushion with ejector function - Continuous stroke control - Floor-level installation - Electrical oil temperature monitoring - Operating manual with circuit diagrams Space required by press (upright) L x W x H: 1800 x 1010 x 3470 mm Space required for horizontal transport L x W x H: 3500 x 1800 x 1200 mm Net weight press: 13 tons Space for hydraulic power unit L x W x H: 1000 x 800 x 3040 mm Net weight hydraulic power unit: approx. 1 ton The machine was used as a tool trial press in a toolmaking workshop. Very good condition.

Condition: good (used), functionality: fully functional, throat depth: 500 mm, pressing force: 160 t, table width: 1,250 mm, Output 160 tonnes --- Working length 1250 mm --- Stroke 250 mm Thrust 500 mm Installation height max. 480 mm Ijdpfxoxfwdho Ag Nstn Weight approx. 11.2 tonnes Output 30 kW Area of application: universally applicable machine: Straightening / bending / pressing / folding etc. --- Was previously used as a folding press with system tool holder + tools .

Condition: good (used), functionality: fully functional, total height: 2,700 mm, pressing force: 25 t, table width: 500 mm, table length: 500 mm, overall weight: 2,000 kg, distance table to ram: 800 mm, stroke length: 500 mm, Equipment: documentation/manual, Available for sale: 1 used hydraulic press Manufacturer: VEB Werkzeugfabrik Zeulenroda WMW Model: PYE25/1 Total weight: 2 t Nominal pressing force: 25 MP Ram stroke: 500 mm Itsdpjxfzdlsfx Ag Njn Maximum distance between table and ram: 800 mm Table: 500 x 500 mm Documentation included

Condition: like new (used), Year of construction: 2023, functionality: fully functional, pressing force: 40 t, table width: 1,500 mm, table length: 1,000 mm, reverse speed: 10 mm/s, ram plate width: 1,500 mm, ram plate length: 1,000 mm, type of input current: AC, travel distance X-axis: 1,200 mm, power: 9 kW (12.24 HP), Equipment: safety light barrier, If the press does not exactly meet your requirements, please click here to request a customized quotation tailored to your needs: HIDROBRASIL manufactures presses to your exact specifications at surprisingly competitive prices! ##### Mould opener-closer with 40 tons pressing force Table and ram size: 1500 x 1000 mm for heated tools Technical data: Pressing force: 40 tons Maximum open height: 1800 mm Ram travel: 1500 mm Oil temperature monitoring: Electric air cooling Lubrication: Manual via grease nipple Travel of the extending table: 1200 mm Speed of the extending table: 30 mm/sec. Electrically steplessly rotatable ram: 180 degrees T-slots: According to customer requirements Pressure setting: From 10 tons to 40 tons Monitor: 10" on the control cabinet for pressure setting and warning messages Two-hand operation Itsdpfxstwmp Ss Ag Nsn Special features: Insulation of the clamping plates towards the ram: With resin insulation plate and special ventilation plate Hydraulic system: With BOSCHREXROTHPARKERATOS components Safety components: From SICK Control system: SIEMENS Remote maintenance unit: SECOMEA - Ethernet Installation and operating conditions: Maximum ambient temperature: 40 °C Height above floor (overall height): Approx. 3800 mm Total weight of the press without operating materials: Approx. 13 tons This machine is supplied in the colors requested by the customer and complies with all EU legal requirements and standards. ##### Are you looking for a customized machine? Contact us for a customized offer.

Condition: excellent (used), Year of construction: 1984, functionality: fully functional, Hydraulic frame press The machine is complete and fully operational Working range 3000 x 2000 mm Itodexmr Spopfx Ag Nen

Condition: used, Year of construction: 1992, functionality: fully functional, installation height: 700 mm, pressing force: 250 t, table width: 1,250 mm, table length: 1,150 mm, die cushion stroke: 150 mm, stroke length: 400 mm, Hydraulic double column press DUNKES HDS 250/10 Year of construction 1992 Technical data: Pressing force at 260 bar: 250 tons Rapid lowering speed: 365 mm/s Table clamping area approx.: 1150 x 1250 mm Ram clamping area approx.: 1150 x 1250 mm Die cushion area approx.: 800 x 1000 mm Die cushion pressing force (200 bar): 100t Die cushion stroke: 150mm Power requirement: 45 kw Installation height: 700 mm Isdpfxoup Si Hj Ag Notn ram stroke: 400 mm Conversion of the control system to SIEMENS (in 2005) Machine height approx. 5,400 mm TP language currently Polish

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. Ijdpfevq Rtkex Ag Netn The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Year of construction: 1989, condition: ready for operation (used), General Data Machine weight 32000 kg Main Drive Spindle motor power 11 kW This HYDRAP HPDB 400 hydraulic press was manufactured in 1989. It is a robust and reliable piece of equipment, ideal for various pressing applications. Consider the opportunity to buy this HYDRAP HPDB 400 hydraulic press. Contact us for more information. Application Types Itedpfoxizg Iox Ag Nen Bending

Condition: good (used), functionality: fully functional, total height: 2,950 mm, throat depth: 360 mm, pressing force: 100 t, table width: 560 mm, table length: 750 mm, overall weight: 5,000 kg, distance table to ram: 630 mm, Equipment: documentation/manual, For sale: 1 used hydraulic press Manufacturer: VEB WEMA Zeulenroda WMW Model: PYE100SS Total weight: 5 t Nominal pressing force: 100 MP Ram stroke: 500 mm Maximum distance between table and ram: 630 mm Table: 750 x 560 mm Isdpfexfzc Isx Ag Netn Two-hand operation and closed hydraulic system

Condition: as good as new (ex-display), Year of construction: 2020, Hydraulic 400 to column press suitable for continuous shift operation, with these basic data: a) Closing speed 100 - 450 mm/sec. b) Opening speed 50 - 250 mm/sec ( adjustable via touch screen ) c) Pressing speed 5 - 60 mm/sec ( adjustable via touch screen ) d) Piston accumulator with approx. 4 nitrogen bottles e) Table size (clamping surface) 2700 x 1700mm ( seen from the front, between the columns ) f) Total table size 3400 x 1700mm g) 28 T-slots according to customer requirements h) Table, ram and press head are annealed stress-free. i) column diameter 250 mm j) slide size 3400 x 1700mm (clamping surface 2700 x 1700mm ) k) Total size of the machine approx. 3900 x 2200 ( at the bottom ) x 5700 mm height l) Oil temperature monitoring ( adjustable via touch screen ) m) Automatic lubrication ( adjustable via touch screen ) n) Free positioning of the ram ( adjustable via touch screen ) o) KEYENCE light barriers 14 mm on front and rear side p) Circuit oil cooling ( adjustable via touch screen ) q) Pressure holding valve 0 to 600 sec. ( adjustable via touch screen ) r) Table top size 3400 x 1700mm, plane milled s) Laterally monitored doors, 1200mm high, 1000mm wide t) RITTAL control cabinet, 2200 mm wide, up to 20 m from the press u) Pressure setting from 50 to 400 tons ( adjustable via touch screen ) v) Travel limitation optionally via pressure or position w) Programming mode, set-up mode, single stroke + continuous stroke (adjustable via rotary switch ) x) Swivelling control panel with 15 inch touch screen monitor y) Two-hand operation on both sides z) Prepared for automatic material feed ( SIEMENS S 7 1500 ) aa) Machine body primed and painted bb) assembly, commissioning, instruction against separate charge The hydraulics of the presses we offer are completely based on BOSCH-REXROTH/Parker/HAWE components. In the switch cabinet only components are used (SIEMENS) which are easily available in Germany. The safety technology comes completely from SICK except for the light barriers. The control system is supplied by SIEMENS. ( S 7 1500 ) as well as the touch screen monitor with 15 inch. The SIEMENS remote maintenance unit SECOME -Ethernet is included in the scope of delivery. SPECIAL FEATURE: the design chosen by us with two press cylinders and the piston accumulator make it possible to supply the full power with a main motor of 90 kW. Below under 1.3 the technical details Technical data Press design Press design Column press Thermally neutral 80 - 120 °C Number of operating sides 2 sides Isdpjg Iihwefx Ag Nstn Forces Pressing force max. 4,000 kN Free ripping force max. 600 kN Pressure build-up time Closed tool steel to steel Max. 2 sec. Dimensions - intended minimum tool height 600 mm Max. Opening width 1600 mm Stroke and min. opening 1000/600 mm Table height above floor 820 mm Height above floor (headroom) approx. 5700 mm Hall height min. 7000 mm Parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.17 mm/m Weight Total weight of the press without operating materials approx. 52 To Speeds ( see attached cycle diagram ) Fast closing 100 - 450 mm/s Pressing speed At F max.

Condition: excellent (used), Year of construction: 1985, functionality: fully functional, The machine is fully operational and in good condition. Working dimensions: 3200 x 2200 mm Dimension adjustment is electrically controlled from the control panel. Ijdpexmr Rxjfx Ag Nstn Powered by a hydraulic unit.

Condition: used, Year of construction: 2011, operating hours: 1,000 h, functionality: fully functional, total height: 4,200 mm, table height: 700 mm, total width: 3,000 mm, total length: 2,000 mm, pressing force: 1,200 t, table width: 3,000 mm, table length: 2,000 mm, overall weight: 60,000 kg, ram plate width: 800 mm, ram plate length: 600 mm, distance table to ram: 700 mm, type of input current: three-phase, distance between stands: 2,200 mm, stroke length: 600 mm, oil tank capacity: 700 l, control cabinet width: 400 mm, input voltage: 380 V, control cabinet height: 2,000 mm, Equipment: safety light barrier, H-frame, 4 columns, daylight 700 mm, stroke 600 mm, distance between columns 2200 mm x 1260 mm, dimensions (LxWxH) 3000x2000x4200 mm, 380V-15kW, weight 60,000 kg Itodpfx Agoxn Rvcj Njn

Condition: used, Hydr. spotting press MILLUTENSIL type BV 25 PM Machine. No. 632 / 25111 Year of construction 1991 Itsdpjtx E Rdjfx Ag Njn Closing force 18 ton. Opening force 15 ton. Table surface 775 x 760 mm Clamping surface of the upper table 900 x 550 mm Frame width 900 mm Installation height max. 750 mm Installation height min. 230 mm Stroke of the upper table 520 mm Lifting speed infinitely variable 0 - 1000 mm/min. Hydraulic pressure adjustable 10 - 200 bar Tool weight on the table max. 2500 kg Tool weight on the upper table max. 800 kg Table height above floor 850 mm Motor power 4 kW Mains connection 380 Volt, 50 Hz - Upper table can be swiveled 360° by motor - Hydraulic ejector unit in the table with 120 mm stroke - M 14 threaded holes in the table - Hydraulically extendable table - Depth adjustment bar for automatic downward stroke limitation Space requirement L x W x H 1550 x 1500 x 2000 mm Weight 1900 kg

Year of construction: 1992, condition: excellent (used), Hydraulic press brake Fab. DARLEY Type. EHP 150 - 43/37 Very good condition, year 1992 Technical data Make: DARLEY Type: EHP 150 - 43/37 Year of manufacture: 1992 working length: 4300 mm power: 150 t distance machine column: 3700 mm ram stroke: 175 mm Engine power: 11 kW Dimensions: approx. L 4.7 x W 1.6 x H 3.1 m (transport height 2.85 m) Weight: approx. 16 t Equipment: - Control Delem DA 58 - Block die: V14, V60, V40, V24, V12, V30, V22, V10 - Punch straight height 195 mm, segmented - 2. punch cranked height 195 mm, segmented, length 4.000mm - controlled axes: Y1, Y2, X, R, Z - motorized crowning - 2 support arms Itjdeh U A Ibopfx Ag Nen - operating instructions + test books All data without guarantee. The machine is in a very good condition. A demonstration under power is possible at any time in our exhibition hall.

Condition: good (used), pressure 250 t passage width 700 mm stroke 850 mm table surface area 2000 x 1000 mm mould height - Max./min. 355 / 1200 mm total power requirement 30 kW weight of the machine ca. 25 t Iodexcblwopfx Ag Netn dimensions of the machine ca. 4,2 x 2,1 x 5,5 m

Condition: like new (used), Year of construction: 2019, pressure:400 t stroke:900 mm Table dimensions:1200 x 1200 mm Iedpjfh Izmjfx Ag Nstn Deep-Drawing Pillow:150 t travel away deep-drawing pillow:280 mm Daylight Opening:1100 mm

Condition: excellent (used), Max working width 9000 mm Max working height 1100 mm 6 upper pressing sections, each 1520 mm 18 front clamps Overall width 13000 mm Overall height 2200 mm Itodpfxoxnwpio Ag Nen

Condition: ready for operation (used), Year of construction: 2012, General Data Machine weight 7500 This SCHAAL SEP63N was manufactured in 2012. It is a robust hydraulic stamping press with a nominal force of 630 kN and a stroke length range of 8-80 mm. It supports tool dimensions up to 710 x 710 mm and operates at a flywheel speed of up to 500 rpm. Power consumption stands at 130 kW, and it requires a 400 V operating voltage. Consider the opportunity to buy this SCHAAL SEP63N hydraulic stamping press. Contact us for more information. Application Types Stamping Itedpsxb E Itsfx Ag Non

Condition: used, Single-column pneumatic press, hydraulic press PAUL ANTON type PVT 2 Pneumatic table press, embossing press No. 97148 Year of manufacture approx. 1980 Compressive force: 10 ton throat depth: 100 mm Ram stroke: approx. 25 mm Plunger surface: Ø 32 mm Table size: 250 x 220 mm Table opening: 53 x 53 mm Table height: 1060 mm Installation height: 155 mm Itedpfx Agetrpiij Nsn - Very stable construction - Hydro-pneumatic press with air to oil pressure ratio - Pneumatic foot switch - ram with M12 internal thread - Metal base Space requirement L x W x H 850 x 620 x 1560 mm Weight approx. 200 kg good condition

Condition: used, Double column hydraulic press RASTER ZEULENRODA (WALTER) type WUP S 60 Ijdsuicg Ujpfx Ag Njtn Machine. No. 136 / 7 (156-165) Year of construction 1999 Basic machine built in 1987, completely overhauled in 1999 with new control system Pressure capacity 60 ton. Stand width 1090 mm Lateral column passage 265 mm (one-sided) Ram area 650 x 300 mm Additional plate on ram 990 x 550 x 60 mm Table surface 990 x 550 mm Plunger stroke max. 320 mm Installation height 330 or 390 mm Table height above floor 980 mm Hydraulic operating pressure 320 bar Rapid traverse downwards 75 mm/s Rapid traverse upwards 100 mm/s Working speed 17 mm/s Return speed 33 mm/s Motor power 15 kW (2x 7.5 KW) Mains connection 400 Volt, 50 Hz, 15.5 kW - Press safety control PILZ PSS 3056-1 + PXT 305 Com-LC - Manually adjustable limit switch cams for stroke limitation - 2-hand operation and electric foot switch - Press force adjustment via handwheel - ram plate additionally guided by 2 lateral guide rods, Ø 50 mm - Table top with 18 mm T-slots, slot spacing 175 mm - Through-hole table top Ø 100 with insert reduction to Ø 30 mm - Plunger plate with 18 mm T-slots, slot spacing 150 mm - Additional ram plate without fastening grooves - Electrical cabinet on the side of the machine stand - Electrical circuit diagram - 2 monitored safety valves for the hydraulics - UVV for manual insertion work Space requirement L x W x H 1950 x 1000 x 2700 mm Weight 2.6 tons good condition

Condition: used, Single-column hydraulic press, straightening press, punching frame ECKOLD Press frame with hydraulic cylinder, mobile press, punching unit Type RSD 1500 - 125 Machine. No. 317 / 690 Year of construction approx. 1986 Compressive force 150 ton. throat 125 mm ram stroke 35 mm Table size 280 x 210 mm Plunger surface Ø 125 mm Installation height (ram to table) max. 265 mm Table height above floor 403 mm Hydraulic operating pressure max. 500 bar - without hydraulic unit - Plunger surface with 4 M16 threads and 20 mm guide groove, central centering hole Ø 15 mm - 1 high-pressure hydraulic hose with external thread M30x1.5 mm, hose length 4 meters - 1 high-pressure hydraulic hose with union nut M30x1.5 mm, hose length 4 meters Itedsd Swtaspfx Ag Nsn Space requirement L x W x H 700 x 300 x 1450 mm Weight 1250 kg Good condition

Condition: used, Hydraulic punch, punch frame for use with JOKA punching units type HP-S Hydraulic hole punch, hydraulic press for punching brackets Year of manufacture: approx. 1995 Pressing force: 5 tons Throat depth: 155 mm Stroke: approx. 20 mm Punching unit width: max. 54 mm Punching unit installation height: max. 220 mm Die holder: Ø 48 mm Motor output: 1.5 kW Power supply: 230 Volt, 50 Hz - Suitable for universal use with JOKA SW 20 or SWD 20 punching units - Throat depth of punching units can be larger, can be pushed through to the rear - Stroke release via electric two-hand control Itodpfjltrmuox Ag Nsn - Hydraulic power pack HAWE, type HCW 4 / 2.5-B 1/400-1 - On subframe, mobile Required space (L x W x H): 1100 x 800 x 1450 mm Weight: approx. 200 kg Good condition