Used Falling Film Evaporators for sale (2,089)

Condition: as good as new (ex-display), Falling-film evaporator – unused – Fsdpod Hb Acofx Aanepp The machine consists of three units that need to be connected in series: - Evaporator (58 pipes), Length: 12.000 mm - Condenser (19 pipes), Length: 15.000 mm - Condenser (48 pipes), Length: ca. 15.000 mm All units are unused and made of stainless steel (AISI 304 / 1.4301). The evaporator was designed for the production of protein powder (dairy industry) and represents the final element of a drying chain. It evaporates the remaining water in the dryer and thus leads to a high concentration of the end product. Since the units have never been in use, they are in excellent quality. Sale without electrical components or control panel.

Condition: used, Used Pfaudler Balfour approximately 4.64 m2 stainless steel wiped film evaporator. Evaporator body approximately 700mm diameter X 2100mm straight side. Internal 1460 litre capacity rated full vacuum/1 bar design pressure at 0-160 °C. Jacket 250 litre capacity rated full vacuum/6 bar (5 bar with full vacuum) design pressure at 0-160 °C. Rotor belt driven by 5.5 kw 415 volt 3/50 1440 rpm motor via Flender model ZF80A gearbox rated 10.29/1 reduction ratio. Fjdpfxoyh Na Ej Aanopp

Condition: new, functionality: fully functional, For sale: Huatai 1.5 TPD lecithin drying line with thin film evaporator and vacuum system. New / unused lecithin drying line for soybean lecithin processing, supplied by Huatai. The line is designed for vacuum drying of crude / wet lecithin and reduction of moisture under controlled temperature and vacuum conditions. Main equipment includes: Thin film evaporator / lecithin dryer Lecithin conditioning tank Finished product tank Hot water tank Lecithin cooler Vacuum pre-condenser Vacuum liquid seal tank Receiving / collection tanks Steam separator / steam distribution vessel Pumps, piping, valves and auxiliary equipment Electrical control cabinet / MCC Fedjzivkbspfx Aanjpp Technical data: Capacity: approx. 1.5 TPD lecithin Process: vacuum drying / thin film evaporation Installed power: approx. 25.2 kW Product contact parts according to manufacturer specification Equipment finish: carbon steel vessels, painted industrial finish; stainless steel parts where required by process design Typical application: soybean lecithin drying crude lecithin moisture reduction vegetable oil refinery lecithin processing lecithin concentration after degumming food / feed / industrial lecithin processing The line is suitable for small and medium vegetable oil processors who want to add lecithin drying and value-added lecithin production to an existing degumming / oil refining process. The equipment is new and unused. Manufacturer: Huatai. EU seller: Leonagra s.r.o. EU invoice possible. Delivery to Europe can be arranged. The listing includes a process schematic and a realistic visual representation of the complete line. Final layout and painting colour can be coordinated before delivery. Inspection / video call with manufacturer can be arranged on request. Price: FCA / delivered EU by agreement, plus VAT where applicable. Zu verkaufen: Huatai 1,5 TPD Lecithin-Trocknungslinie mit Dünnschichtverdampfer und Vakuumsystem. Neue / unbenutzte Anlage zur Vakuumtrocknung von Sojalecithin. Die Anlage ist für die Trocknung von Rohlecithin bzw. feuchtem Lecithin unter kontrollierten Vakuum- und Temperaturbedingungen ausgelegt. Hauptkomponenten: Dünnschichtverdampfer / Lecithin-Trockner Lecithin-Konditionierungstank Fertigprodukttank Heißwassertank Lecithin-Kühler Vakuum-Vorkondensator Vakuum-Flüssigkeitsverschlussbehälter Auffang- / Sammeltanks Dampfverteiler Pumpen, Rohrleitungen, Ventile und Zubehör Schaltschrank / MCC Technische Daten: Kapazität: ca. 1,5 TPD Lecithin Verfahren: Vakuumtrocknung / Dünnschichtverdampfung Installierte Leistung: ca. 25,2 kW Industrieausführung mit lackierten Kohlenstoffstahlbehältern; Edelstahlteile dort, wo prozesstechnisch erforderlich Geeignet für Sojalecithin, Pflanzenölraffination, Lecithin-Trocknung nach Degumming und kleinere bis mittlere Ölmühlen / Raffinerien. Hersteller: Huatai. Verkäufer in der EU: Leonagra s.r.o. EU-Rechnung möglich. Lieferung nach Europa kann organisiert werden. Besichtigung / Videocall mit dem Hersteller auf Anfrage möglich. Preis: nach Vereinbarung, zzgl. MwSt.

Condition: used, Year of construction: 1996, Evaporation plant designed for concentrating milk and whey, consisting of the following components: - A pre-evaporator with : 6 stages (vertical falling-film tube bundles), approximately 15 metres high. - A finishing evaporator consisting of 1 falling-film stage. - A cooling unit. - Piping, valves, pumps and various instrumentation. The original supply did not include the electrical power and control panels, which were manufactured and connected separately from the GEA supply. The automation system and related software were also excluded from the supply. Below are some of the plant's technical specifications: - Plant capacity: 60,000 litres/hour of whey with a dry matter content of 6%. - Final product concentration: up to 60% dry matter, corresponding to an evaporation capacity of 54,000 litres/hour of water. - Saturated steam consumption at 12 bar during concentration: 6,200 kg/hour. - Saturated steam consumption at 12 bar during concentration: 6,500 kg/hour. - Installed electrical power: 130 kW. Fedo Ai Hh Uspfx Aanjpp These figures have been taken from the original purchase order. However, some modifications may have been made during the commissioning phase. The plant was purchased in 1995 and it has been put into service in 1996. It was used for whey concentration until 2021/2022, when it was replaced by a reverse osmosis concentration system. * Installed electrical power: 130 kW.

Year of construction: 2021, condition: excellent (used), functionality: fully functional, The refrigerant gas exits the compressor and flows to the air inlet connection of the ATC-E condenser. Heat from the refrigerant is transferred through the heat exchanger tubes to the water that flows downward through the tubes. Simultaneously, air is drawn into the air inlet grilles at the base of the condenser and flows upward over the heat exchanger, counter to the water flow. A small portion of the water evaporates, and heat is removed from the system. The warm, moist air is drawn by the fan to the top of the evaporative condenser and released into the atmosphere. The remaining water falls into the collection basin at the bottom of the condenser, where it is recirculated through the water distribution system and flows down over the heat exchanger. Thermal-Pak II Heat Exchanger EVAPCO's Thermal-Pak II heat exchangers, featuring a patented design, ensure maximum cooling capacity. The airflow through the heat exchanger is countercurrent to the fluid flow, resulting in the most efficient heat transfer process. A specially designed heat exchanger is used to reduce air pressure drop across the unit while maximizing the tube surface area and increasing the heat transfer capacity. Elliptical return bends provide more circuits per heat exchanger bundle and increase the maximum capacity per footprint. The heat exchanger is located in the airflow, resulting in an increase in the dry-bulb temperature. CrossCool internal tube enhancement increases fluid turbulence and provides additional evaporative capacity. Available in type 304 SS or type 316 SS construction. Drift eliminators Limit drift rate to no more than 0.001% of the recirculated water flow rate. Minimize the risk of Legionella spread. Fpedpfxj Ag Id Tj Aanep Constructed with an inert polyvinyl chloride (PVC). Superior air inlet louvers and screen design. Constructed with an inert polyvinyl chloride (PVC). Two-tier design that minimizes drift loss and the potential for algae growth in the tower. Framed in steel in easily removable sections. Pressurized water distribution system EVAPCO's zero-maintenance ZMII® spray nozzle remains clog-free, allowing for even and consistent water distribution. This makes it the best-performing, corrosion-resistant, and maintenance-free water distribution system in the industry. ZMII spray nozzles have a 1-1/4" diameter opening and a 1-1/4" transparent splash plate. Mounted in corrosion-resistant PVC water distribution piping with threaded end caps. Provides unparalleled heat exchanger coverage and scale prevention. Stainless Steel Water Basin Available in type 304 or type 316 stainless steel. Covers the entire area of the water basin, including the supporting columns and the frame of the louvers. Welded water basin seams for leak-free operation. Stainless Steel Housing and Fan Available in type 304 or type 316 stainless steel. Covers the entire upper section, including the fan shroud. Stainless Steel Thermal-Pak II Heat Exchanger Available in type 304 or type 316 stainless steel. The stainless steel heat exchanger offers superior resistance to corrosion in harsh environments and is available within EVAPCO's standard delivery time! The EVAPCO 304 STT heat exchanger option can be manufactured as an ASME heat exchanger.

Condition: used, System Overview A complete, cGMP-compliant Water for Injection (WFI) generation and storage system. Produces high-purity, endotoxin-free water for pharmaceutical and biotech applications via multiple-effect distillation. This item can be crated and shipped internationally. Please contact us for a quotation ----- Main Components - Finn-Aqua 200-S3 Distillation Unit – three-effect evaporator/condensers with falling-film design, pyrogen separation, and continuous blowdown. - 600 L WFI Storage Tank – 316L stainless steel, atmospheric vent filter, level and temperature sensors. Fodpfexqq Dxsx Aanepp - 600 L Jacketed Holding Tank – 316L stainless steel, insulated, steam/hot water jacket for temperature control. - WFI Distribution Pump – sanitary centrifugal pump for loop circulation. - Utility Connections – plant steam (3–8 bar), cooling water, feed water, condensate return, and instrument air. - Instrumentation – pressure, temperature, conductivity, and level transmitters with safety and relief valves. - Control Panel – PLC-based automatic operation, alarm handling, data logging, and local/remote control. ----- Key Features - Multi-effect distillation for high purity and energy efficiency. - Degassing and three-stage separation for endotoxin removal. - Fully stainless, drainable, and sanitary construction. - Compact, skid-mounted design with integrated utilities. - Designed for validation and GMP compliance (USP/EP WFI quality).

Year of construction: 2023, operating hours: 500 h, condition: like new (used), functionality: fully functional, We offer a complete industrial production line designed for the extraction, purification, concentration and spray drying of collagen derived from fish processing by-products. The production line is designed to process fish skin and fish bones into collagen powder using controlled enzymatic hydrolysis, mechanical separation, filtration, ion exchange purification, evaporation and spray drying. The system integrates multiple processing stages into one industrial production solution. Main Equipment Included 1. Collagen Extraction and Enzymatic Hydrolysis System 3 × stainless steel enzymatic reaction tanks, each with 3,000 L effective capacity SUS316L product-contact surfaces Heating jackets, insulation and agitators Enzyme preparation and acid dosing tanks Pumps, vibrating screen and intermediate storage tanks Temperature, level and pH monitoring Siemens PLC control system 2. Separation System Industrial decanter centrifuge, model LW350, capacity 2–3 t/h Disc separator, model BDY311, capacity 2–3 t/h Stainless steel receiving and storage tanks Transfer pumps and process control system 3. Purification and Decolorization System Anion and cation exchange columns Activated carbon filtration system Stainless steel plate filtration unit Regeneration tanks Heat exchanger and transfer pumps Automated process control 4. Concentration and Drying System Double-effect falling film evaporator Water evaporation capacity: 1,600 kg/h Concentrate holding tanks Industrial spray dryer Spray dryer water evaporation capacity: 150 kg/h Hot air generation and powder collection system 5. Cleaning and Water Treatment Automatic CIP cleaning system with 4 × 3,000 L tanks CIP circulation pumps Reverse osmosis (RO) water treatment system Water treatment capacity: 5,000 L/h Stainless steel process piping and associated equipment Technical Specifications Finished product: Fish collagen powder Nominal production capacity: Approx. 1,000 kg/day Raw material requirement: Approx. 5–6 tonnes/day Steam requirement: Approx. 2 tonnes/hour Electrical power requirement: Approx. 300 kW Compressed air requirement: Approx. 1 m³/hour Cooling system: Circulating cooling water Main process materials: Stainless steel SUS304 / SUS316L Automation: Siemens PLC and touchscreen control systems Production Process Raw material washing → Enzymatic hydrolysis → Filtration → Decanter separation → Disc separation → Ion exchange purification → Activated carbon filtration → Sterilization → Concentration → Spray drying → Powder collection and packaging. Applications The production line is intended for industrial processing of fish-derived raw materials into collagen powder. Potential applications include: Marine collagen production Fish processing by-product valorization Collagen ingredient manufacturing Food ingredient production Nutraceutical raw material processing Final product specifications and suitability for particular applications depend on the selected process parameters, raw material quality and validation. Additional Information Fodpfo Ahynvjx Aanepp The system is designed as an integrated industrial processing line, including extraction, separation, purification, concentration, drying, cleaning and water treatment equipment. Detailed equipment specifications and technical documentation are available upon request.

Condition: used, Year of construction: 2021, functionality: fully functional, Dürr Ecopure VAR 2206 Thermal Oxidizer with Flue Gas Cleaning (2021) For burning liquid and gaseous waste streams including fluorinated gases, e.g. PFAS, and recovery of aqueous hydrogen fluoride Emissions limits SO2 ≤ 100 mg/Nm³ NOX ≤ 30 mg/Nm³ CO ≤ 50 mg/Nm³ CF4 ≤ 70 mg/Nm³ HF ≤ 1 mg/Nm³ NH3 ≤ 2 mg/Nm³ Comprising Direct fired thermal oxidizer Hot gas cooling and acid recovery Alkaline wet scrubber Honeycomb selective catalytic reduction deNOx system >1M cost spare parts Direct fired thermal oxidizer Including 2x natural gas combustion chambers and burners - High calorific liquid waste requires safe ignition supplemental hydrogen supply for acid formation - Gaseous waste streams injected via nozzles downstream and close to the burner - 1.5MW multi-fuel natural gas & liquid waste (minor fuel stream) burner with natural gas capacity up to 200Nm3/h - 1400C normal, 1540C max allowable temperature destruction of pollutants to reduce emissions with 3.28 MW thermal energy transfer - 2 seconds minimum residence time in combustion chamber at 1400C - 1,800mm combustion chamber internal dia. - Approx 300mm refractory lining - 2,400mm combustion chamber external dia. - 12,000mm combustion chamber internal length - 3.28MW maximum thermal capacity - 4,900Nm3/h, 60mbar, 14kW combustion air fans One chamber is active, the other one is on standby and can be prepared, repaired, or maintained. This allows minimizing shutdown and changeover time to only several days Wet scrubber hot gas cooling and acid recovery SGL Carbon Diabon HT-PQ 850 graphite pipe quencher - 6,000 Nm3/h capacity flow - 1,100 mm dia. - 2,000mm high - pumps SGL Carbon Diabon THX-RS falling film absorber shell & tube heat exchanger - 1,100mm dia. - 4,500mm tube length - 595 no. tubes - 22mm tube internal dia. - Graphite, carbon steel - pumps Quench vessel - PP/FRP - 1,100mm dia. - Approx. 6,000mm high 2x Scrubber absorber columns, each - Shell FRP/PP - Internals PP - 1,000mm dia. - 11,000mm high - Pumps - Dosing station Fedpfez Ai Tpex Aanjpp FRP 5m3 Emergency water tank - 1,600mm dia. - 3,000mm high - 3kW heating 2x Teblick 100,000L HDPE hydrofluoric acid tanks (2019) Honeycomb selective catalytic reduction deNOx system - 5,900Nm3/h, 130mbar, 42kW induced draft fan - 320 kW gas/gas heat exchanger - 500 kW capacity reheat burner - 1.2m deNOx honeycomb catalyst Clean gas outflow Stack with flow & temperature measurement Spare parts include - 200 items of sensors, pumps, valves, gaskets, joints etc. - Graphite quencher - Falling film absorber With the redesign and maintenance support of Dürr, the system could also - be adapted to other halogenated gases with bricks to be selected according to gas application - cope with the presence of VOCs or contaminated air - larger volumes with the addition of a small lance for 15kg/h liquid injection

Year of construction: 2013, condition: ready for operation (used), Mariani Shrink film wrapper Model: TRM 700-LF-I YOM 2013 Including in/outfeed conveyor system Fsdoyilyqjpfx Aanspp Working width: 700mm Cardboard Trays – Cases with protective shrinked film Portion packs : 3 x 8 – 3 x 9 – 3 x 10 Family packs : 2 x 6 – 3 x 4 Output: Max 25 trays per min, varying according to the format required Dimensions machine (LxWxH): 5000x1400x2100mm

Year of construction: 2013, condition: excellent (used), functionality: fully functional, REF: MM6423 Complete weighing and bagging system which has previously been used to pack frozen peas and vegetarian products into pillow packs. This system comprises of the following equipment: 1 x Infeed swan-neck conveyor with flighted belt mounted on mobile frame (stored outside). Date of manufacture - 2013. Belt width - 245mm wide. 1 x Yamato Scale Dataweigh (UK) Ltd ADW-514AWCC 14-head multi-head weigher with dimple pans. Manufacturer - Yamato Scale Co., Ltd. Speed - up to 120 drops/minute (depending on product and weight). Weighing range - up to 1000g. Rated to IP66 (waterproof). 1 x Gantry unit with steps. Footprint dimensions - 5.7m long x 2.7m wide x 2.72m high. Fodey Um T Hopfx Aanspp 1 x Gainsborough Engineering Ltd GV2K3 vertical form, fill and seal bagging machine. Manufacturer - Gainsborough Engineering Ltd. Date of manufacture - 2013. Sealing jaws: Horizontal - 360mm wide / Vertical - 420mm long. Packing speed - up to 60 packs/minute (depending on bag size). Bag size range: Smallest - 80mm wide x 80mm long / Largest - 320mm wide x 350mm long. Supplied with jaws for poly and laminate film, block-bottom and gusseted bags as well as 3 x forming tubes. Forming tubes: for forming pillow/’fin-seal’ packs measuring 130mm, 220mm and 270mm wide. 1 x Outfeed inclined conveyor. Belt dimensions – 2250mm long x 425mm wide. Outfeed height – 1000mmm. Some spare parts are also included. Videos available on request.

Condition: excellent (used), functionality: fully functional, Production lines for fruit and vegetable preserves. A significant portion of the equipment is newer – from 2011 and 2014 – supplemented by older, robust machines that have proven their reliability through years of continuous operation. The machines are sold as a complete line. Line capacity (based on an example product) – approximately 1200 liter jars/hour (~1.5 tons/hour). This translates to approximately 28,800 jars/day, or ~36 tons/day. (I) What can be produced on this line: - Compotes (jars, bottles) - Jams and thick preserves - Juices (bottle filling, tube pasteurization) - Canned goods (sterilization in an autoclave) - Pasteurized preserves in jars (pickles, vegetables, sauces) (II) Process flow: 1. Product dosing – into buckets, jars (2 dosing machines) 2. Filling – bottles (filling machine), cans (dosing machine + seamer) 3. Thermal processing – boiling tank, evaporators (juice/puree concentration), tube pasteurizer (liquid product before filling) 4. Packaging closing – sealers (bottles, jars), capping machine 5. Sterilization/pasteurization of finished packaging – autoclave (cans, jars), tunnel pasteurizers (3 units) Fpsdpfxez Daato Aansp 6. Labeling – labelers for bottles, jars and cartons 7. Collective packaging – heat tunnels (shrink film), conveyors (III) Equipment list: 1. Carton labeler 2. Heat tunnel (shrink film) 3. Conveyors 4. Heat tunnel 5. Bottle labeler 6. Jar/bottle labeler 7. Heat tunnel x 3 8. Labeler (without control panel) 9. Tunnel pasteurizer x2 10. Dosing machine for buckets 11. Dosing machine + seamer for cans 12. Pleszew Autoclave (2011) 13. Tunnel pasteurizer 14. Dosing machine 15. Capping machine 16. Seamer 17. Bottle filling machine 18. Jar seamer 19. Dosing machine for jars x2 20. Tube pasteurizer 21. Evaporator x3 22. Boiling tank Total value: 2,380,000 PLN = ~ 545,000 EUR (IV) Why buy the entire line: Complete process line – from dosing to collective packaging – without the need to find missing components. Option for pickup with dismantling and transportation (to be agreed upon). Equipment used in production – documented history of use. Flexible sales options: entire line, separate technological units (e.g., canned goods section with autoclave, bottle filling section), or individual machines. Terms: Visit possible by prior arrangement. Transportation and dismantling to be agreed upon.

Year of construction: 2003, condition: good (used), functionality: fully functional, 1 x Gainsborough Engineering Ltd packing system, previously used to pack small machine components. Comprising of infeed pocket conveyor, vertical form, fill and seal bagger fitted with Zodiac HS printer and an outfeed conveyor. Manufacturer - Gainsborough Engineering Ltd. Model of VFFS bagger – GV2K1. Date of manufacture – 2003. Sealing bars - 250mm long (vertical & horizontal). Reel width - 505mm. Current film - 230mm. Fpjdpfx Aaey Hlvwonop Forming tube - 60mm diameter. Sorting / infeed table - 1500mm long x 710mm wide. Outfeed conveyor - 290mm wide belt x 950mm outfeed. Overall footprint - 6.15m long x 1.7m wide x 2.2m high. Condition – Fully operational.

Condition: used, Year of construction: 2023, Overview This Robopac Genesis Futura HS pallet winder was built in 2023. It has under 500 operating hours - technically close to new. The rotating ring carries the pre-stretch carriage around the stationary pallet for high throughput without moving the load (see Capacity below). Delivered as a stand-alone unit with integrated roller conveyor, prepared for line integration over Ethernet TCP/IP. Technical data - Manufacturer: Robopac - Model: Genesis Futura HS - Year of manufacture: 2023 - Machine type: automatic rotating-ring stretch wrapper (pallet winder) - Operating hours: less than 500 h - Capacity: up to 92 pallets/h (13 wraps, H 1,000 mm), 77 pallets/h (17 wraps, H 1,600 mm), 70 pallets/h (19 wraps, H 2,000 mm) - Pallet size: 800 x 1,200 mm - Load height: 1,000 - 2,000 mm (incl. pallet) - Load weight: 100 - 1,200 kg - Conveyor height: approx. 550 mm; speed 15 m/min - Machine height: approx. 4,862 mm; hall height from 7,000 mm - Pre-stretch: SCV-B carriage, electronically adjustable 150 - 400 % - Stretch film: LDPE / LLDPE, 17 - 23 µm, roll width 500 mm, max. diameter 250 mm, core 76 mm, max. weight 20 kg - Control: Siemens SIMATIC S7-1200 PLC, Siemens TP700 7" colour touch panel - Wrapping programs: 15 (expandable to 64), 12 steps/recipe, 4 password-protected access levels - Power supply: 400 V / 50 Hz, TN-S, control voltage 24 VDC - Compressed air: 6 bar, dry, oil-free - Documentation and HMI languages: German / English Equipment - High-speed rotating ring: power transfer to the pre-stretch carriage via sliding contacts, Wi-Fi commands - Integrated roller conveyor with pneumatic pallet lifting station (SMC PL-D) - Automatic film clamping, cutting and wide-band sealing unit - Fixed vertical hold-down (top press unit) stabilises the load during wrapping - Roping device gathers the film web from below - Photocell for automatic pallet-height reading, plus a pre-scan photocell with 3,800 mm reflector mast - Inverter-controlled IE3 motors, SEW geared, IP55, FESTO pneumatic components, SICK photocells - Siemens Scalance S615 VPN / firewall router and Scalance XB005 Ethernet switch, TCP/IP link to up-/downstream machines - Safety: Reer Safegate SMPO 1803 light curtain, fenced enclosure, dynamic fall protection on the ring - Operator panel separate from the main switch cabinet, plus remote control unit with emergency stop - R-Connect remote monitoring hardware: cloud portal for production data and teleservice - TPM package (centralised lubrication points, maintenance intervals on display), integrated HMI troubleshooting - Complete documentation on USB stick and in print: operating / maintenance manual, wiring / pneumatic diagrams, spare parts catalogue, layout Condition Used - almost as new, no visible production wear. Still installed and under power; inspection in operation on request. Sold without warranty. Fedpfozzz R Dsx Aanspp Availability Immediately. Location: Germany. Handed over dismantled and packed (EXW).

Year of construction: 1999, condition: repair required (used), functionality: limited functionality, Complete bagging system, comprising of: 1 x Ilapak vertical form, fill and seal bagging machine. Type - VT 1000 S. Serial number - S 767 99. Sealing bars: Horiztonal - 300mm long / Vertical - 385mm long. Forming tube - 58mm diameter. Fitted with Markem SmartDate 3 coder. Fjdpfe Ai Hhbox Aanjpp 1 x Safeline 30H gravity fall metal detector. Throat - 100mm diameter. 1 x Outfeed inclined conveyor with flighted belt. Belt width - 120mm wide. Condition: Bagger - Spares only / For refurbishment. Safeline metal detector - Fully working (Video available). Outfeed conveyor - Fully working (Video available).

Condition: ready for operation (used), Plastic Film Wash Line with Extruder Available in Ireland Can be seen running if necessary Sink Float Tank Fsdpfx Aaezylxisnopp Centrifuge Washer Dryer Extruder Granulator Shredder Everything required for the washing and recycling of Plastic Material 1 Tonne per Hour

Condition: good (used), Year of construction: 2019, Centauro MTE-4J2-24 Industrial cubic air evaporator Fpodpfx Aozvllbjansp 2019, used for commercial refrigeration and cold rooms, powered by dual 450mm fans, cooling capacity of around 24Kw, two in stock, 3Ph

Year of construction: 2026, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S25Synthesi11, Stretch Winder Synthesi Freezer -30 IP65 TECHNICAL DETAILS Turntable / base frame / Ø 1500 mm Max. pallet dimensions: 800 x 1,200 mm Max. load capacity: 2,000 kg Wrapping height (pallet included) 2,400 mm FILM SLIDE TYPE "OPRS - ONE PRE STRETCH" Film pre-stretch ratio set to 200% Foil application tension electronically adjustable in the programs in different steps Height of turntable 75 mm Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function & reset according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F00 - Screen lock program change F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Winding height photocell delay F13 - F16 - Foil application tension foot & head wrapping / ascent & descent independently adjustable F62 - Ergonomic height for film change Fodpfoz Iq I Ajx Aanopp Foil consumption display (optional) ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 6 storable winding programs F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - Push button for manual functions F10 - F11 - Wrap cycle with preset start and stop height F12 - Winding to a stored height (switching off the light button for the height) F22 / F23 - Winding cycle for cover sheet film F29 - Soft start cycle for edge protection application F30 - F31 - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges Winding cycle with manual or motorized line formation (optional) Reinforcement cycle via push button Optionally possible: Turntable size up to Ø2600 mm Mast height up to 3900mm ramp mounting frame Light scanner for black products cutting device Etc. Other systems available from the Ludwigsburg warehouse. Some images may contain options that are subject to a surcharge. Illustration similar

Year of construction: 2025, operating hours: 1 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: SFERA21Kommission4, Stretch winder ATLANTA SFERA Easy 6 programs can be saved individually Winding height 2150mm Mast height 2050 mm (fits through almost every door) Foil specification Max. outer diameter Ø300mm - height = 500mm - core Ø76mm Fpedpfoz Inavjx Aanep GMK (compass) The start and end of the winding is always identical Manual line formation Tension of the film can be saved in 4 steps TECHNICAL DETAILS: two maintenance-free AGM batteries 12 V - 100 Ah connected in series 160 pallets per charge - charging time: 8 -10 hours High frequency battery charger with LED indicator Wrapping height “machine with MAST (pallet included) 2,150 mm Height query via light button or by entering dimensions on the display Protective bar for emergency stop of the travel drive Emergency stop switch according to CE regulations Acoustic warning signal and warning light when the machine starts Fall protection for the film slide Push button for start & stop Function of the machine according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL: All function parameters can be set via the display F00 - Screen lock program change F02 - Adjustable machine speed around the pallet up to 80 m/min Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F13 - F16 - Foil application tension foot & head wrapping / ascent & descent independently adjustable F17 - F20 - Foil pre-stretching foot & head wrapping / ascent & descent independently adjustable F62 - Ergonomic height for film change Display foil consumption (option for PRS - PS) ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL: 6 storable wrapping programs for SFERA EASY F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F10 - F11 - Wrap cycle with preset start and stop height F12 - Winding to a stored height (switching off the light button for the height) F21 - Wrapping cycle for large pallets F22 / F23 - Winding cycle for cover sheet film F29 - Soft start cycle for edge protection application F30 - F31 - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges

Condition: used, Skinetta ASK 450 Stretch Banding Machine Purpose of the Machine The stretch banding machines in the SKINETTA series are designed for tightly wrapping individual or multiple products with polyethylene film. In contrast to shrink wrapping machines, the film is stretched tightly around the packaging before sealing. This tension is the main advantage of this process, reducing film consumption by up to 20%. A particular advantage of the patented SKINETTA sealing system is the stepless, precise metering. The film is sealed in a very small area (welded), resulting in a clean seal with minimal overhang. By using a SKINETTAther or SKINETTAshrink hot air hood and a sufficiently wide film, the overhanging film can be reduced laterally. This increases the stability of the container and prevents individual products in correspondingly grouped containers from falling out sideways. With suitable additional devices, a complete closure of the containers can be achieved by sealing, crimping, and folding the sides. The SKINETTA stretch banding machine program includes six basic models for film widths of 25 to 200 mm, 290 mm, 440 mm, 590 mm, 790 mm, and 1,250 mm. Fpodpep U T Ifofx Aanep In addition to the single-lane version, two- to four-lane systems are available to increase production output. SK series (semi-automatic): In the SK series, the products are manually grouped on the machine table by an operator. The insertion into the film and the subsequent stretch banding process are initiated either via a foot switch or a two-hand control. A later upgrade to fully automatic operation is possible (except for model SK 200). ASK series (fully automatic): In the ASK series, the product feed, grouping, and subsequent banding are fully automatic with the help of appropriate additional devices. A modular system of feed, grouping, forming, and special components enables individual adaptation to a wide range of customer requirements. Thanks to more than 20 years of experience, proven standard components can be used for a wide variety of packaging tasks. Technical data Machine dimensions (basic machine) Length: 1670 mm Width: 980 mm Height: 1700 mm Table height: 1700 mm Weight: 400 kg Power connection: 400 V Power consumption: 6.1 kW Additional equipment: rod chain conveyor You can find more items – new and used – in our shop! International shipping costs on request!

Year of construction: 2026, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S23SynthesiLow05, Exhibition machine, like new. SYNTHESI with a flat turntable Turntable height 25mm Short ramp 500mm long TECHNICAL DETAILS: Turntable LOW PROFILE · Height 25mm · Max. pallet dimensions: 1000 x 1200 mm · Max. load capacity: 1200 kg · a ramp included Wrapping height (pallet included) 2,200 mm Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function & reset according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F00 - Screen lock program change F02 - Infinitely variable turntable speed 5-12 rpm Fpjdpfx Asz Ipwceanjp Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Winding height photocell delay F13 - F16 - Foil application tension foot & head wrapping / ascent & descent independently adjustable F62 - Ergonomic height for film change Foil consumption display (optional) ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 6 storable winding programs F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - Push button for manual functions F10 - F11 - Wrap cycle with preset start and stop height F12 - Winding to a stored height (switching off the light button for the height) F22 / F23 - Winding cycle for cover sheet film F29 - Soft start cycle for edge protection application F30 - F31 - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges Winding cycle with manual or motorized line formation (optional) Reinforcement cycle via push button FILM SLIDE TYPE "OPRS - ONE PRE STRETCH" Film pre-stretch ratio set to 200% Foil application tension electronically controlled via control unit Foil specification Max. outer diameter Ø250mm - height = 500mm - core Ø76mm Standard connection values: 230 V - 1PH+N+PE - 50/60 HZ Total power: 1.2KW / 8A Optional: pinion for OPRS pre-stretching ratio of 150% / 250% / 300% possible Other systems available from the Ludwigsburg warehouse.

Year of construction: 2026, operating hours: 1 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S22EVA_07, Exhibition machine - like new. EVA Turntable / base frame increased / Ø 1,500 mm Max. pallet dimensions: 800 x 1,200 mm Max. load capacity: 1,500 kg Wrapping height (pallet included) 2,200 mm Raised base frame by 150mm - 200mm, for charging with E-Ant - adjustable Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL Fsdez Ipr Hspfx Aanepp All function parameters can be set via the display F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F62 - Ergonomic height for film change ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 1 storable wrapping program F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - manual winding F12 - winding to a stored height (while switching off the light button) F29 - Soft start cycle for edge protection application Soft start to reduce film tears on sharp pallet edges FILM SLIDE TYPE “FM” WITH MECHANICAL BRAKE via manually adjustable brake roller on the foil carriage Foil specification Max. outer diameter Ø 250 mm - core Ø76mm - height = 500 mm Standard connection values: 230 V - 1L+N+PE - 50 HZ Total power: 1.2KW / 6A Other systems are immediately available from stock.

Condition: ready for operation (used), functionality: fully functional, The THIMON SWING PRO 5-sided strapping machine is a state-of-the-art industrial solution designed to provide complete pallet strapping using a single consumable. Thanks to its patented triangular arm technology combined with a motorized rotary table, it performs the packaging of all five sides of the pallet in a single cycle, while guaranteeing excellent load stability. This technology improves the protection of goods against dust, moisture, and stresses related to transport. Fpodozhwfkjpfx Aanep Designed for the food processing, logistics, pharmaceutical, paper, or manufacturing industries, the WRA-PAL SWING PRO combines a high throughput with reduced stretch film consumption. Its motorized pre-stretch module and 1,000 mm film width allow for a reduction in consumable usage of 20 to 40% while improving load retention. Furthermore, its capacity to accommodate reels up to 100 kg offers significantly greater autonomy than conventional systems and limits production downtime. The machine easily adapts to different pallet sizes thanks to its numerous adjustments. Its cutting and heat-sealing device eliminates film tails at the end of the cycle, while its patented pleated film system reinforces the cohesion between the pallet and the load. In addition, the use of a single film for all five sides guarantees inviolable product protection and improves their preservation during storage and transport. At Europ'Équipement, this strapping machine undergoes a complete overhaul before being sold. Each component is inspected, serviced, and tested to offer manufacturers a reliable, high-performance, and immediately operational solution, while significantly reducing the investment compared to new equipment. Technical specifications: Packaging of all 5 sides with a single film reel Motorized rotary table Patented triangular arm with mobile linkage Motorized pre-stretch module Film width: 1,000 mm Adjustable pre-stretch: 0 to 350% Reel capacity up to 100 kg Automatic cutting and heat-sealing device Pleated film reinforcing load cohesion Anti-fall system for the stretching carriage Touchscreen operator interface Frequency inverters Programmable industrial controller Adaptation to different pallet sizes Simplified maintenance thanks to optimized kinematics

Year of construction: 2026, operating hours: 2 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S22EVA_03, Exhibition machine - like new. EVA Turntable / base frame increased / Ø 1,500 mm Max. pallet dimensions: 800 x 1,200 mm Max. load capacity: 1,500 kg Wrapping height (pallet included) 2,200 mm Raised base frame by 150mm - 200mm, for charging with E-Ant - adjustable Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F62 - Ergonomic height for film change ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 1 storable wrapping program F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - manual winding F12 - winding to a stored height (while switching off the light button) F29 - Soft start cycle for edge protection application Soft start to reduce film tears on sharp pallet edges FILM SLIDE TYPE “FM” WITH MECHANICAL BRAKE via manually adjustable brake roller on the foil carriage Foil specification Max. outer diameter Ø 250 mm - core Ø76mm - height = 500 mm Fpsdpfx Aaez Iqnvenep Standard connection values: 230 V - 1L+N+PE - 50 HZ Total power: 1.2KW / 6A Other systems are immediately available from stock.

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, machine/vehicle number: 1755741, total length: 4,500 mm, total height: 1,800 mm, total width: 1,900 mm, input voltage: 400 V, energy consumption: 23 kWh, Industrial Film Wrapping Machine LPFK1-218 Manufacturer: Lerum Pac Maskin AB, Sweden Model: LPFK1-218 | Year: approx. 2017 Machine No.: 1755741 Industrial film wrapping machine for automatic packaging of wood products, boards and long profiles. The machine has been used at Superwood A/S and has a total operating time of less than one month. It is being sold due to changes in the production line. Technical data: Max. film width: 800 mm Adjustable conveyor speed Fpjdpfx Aas Ahnkzjnep Digital temperature control 400 V / 50 Hz, 23 kW Siemens SIMATIC HMI and PLC control Frequency inverters, CE marked Dimensions (L × W × H): approx. 4,500 × 1,880 × 1,560 mm Original documentation included, including manual, electrical and pneumatic diagrams, and spare parts lists. The machine is sold in its current condition. Important: The machine will be removed from the production line in week 52, 2026. Collection is possible from week 2, 2027. Price: EUR 35,000 excl. VAT Location: Hampen, Denmark Delivery: EXW, buyer arranges collection and transport.

Year of construction: 2026, operating hours: 1 h, condition: as good as new (ex-display), machine/vehicle number: S23EVA01, Stretch wrapper EVA TECHNICAL DETAILS Turntable / base frame / Ø 1,500 mm Max. pallet dimensions: 800 x 1,200 mm Max. load capacity: 1,500 kg Wrapping height (pallet included) 2,200 mm Height of turntable 75 mm Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F62 - Ergonomic height for film change ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 1 storable wrapping program F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - manual winding F12 - winding to a stored height (while switching off the light button) F29 - Soft start cycle for edge protection application Soft start to reduce film tears on sharp pallet edges FILM SLIDE TYPE “FM” WITH MECHANICAL BRAKE via manually adjustable brake roller on the foil carriage Foil specification Max. outer diameter Ø 250 mm - core Ø76mm - height = 500 mm Standard connection values: 230 V - 1L+N+PE - 50 HZ Total power: 1.2KW / 6A Options: Turntable 1650mm Fodoz Ip S Hspfx Aanjpp ramp mounting frame Light scanner for black products Other systems available from the Ludwigsburg warehouse.