Used Galvanotechnik Leipzig for sale (670)

Condition: good (used), 88 units of picking carts, Wanzl – used: Price per unit, ex works: only €125.00 (net) Manufacturer: Wanzl Type: unknown Year of manufacture: unknown Dimensions: 1500 x 607 x 2073 mm Most have a grid back panel and three to four intermediate shelves 2 swivel casters, 2 fixed casters Gbjdpozbyhvjfx Adcsn Push handle Condition: good Available: immediately Location: Leipzig area

Condition: new, Telescopic support for parking semi-trailer trucks, dancop telescopic support – New: Price ex works: €700.00 (net)! Gbedpfx Aszbyg Eodcjn Manufacturer: dancop Type: unknown Year of manufacture: unknown Width: 760 mm Weight: 71.58 kg Maximum lifting height: 1344 mm Height: 1025 - 1344 mm Height adjustment: manual Material: steel Surface: powder-coated RAL 1023 traffic yellow Width of base plate: 470 mm Depth of base plate: 425 mm Height of base plate: 10 mm Color of base plate: yellow Depth: 670 mm Load capacity: 40000 kg Current new price: approx. €1,200.00 (net) Condition: very good, unused Available: from approx. August 2026 Location: Leipzig

Condition: good (used), Year of construction: 2006, Column-swiveling crane, SchmidHandling, with Demag chain hoist, 125kg – used: Price ex works: €1,750.00 (net)! Manufacturer: SchmidHandling Type: (to be specified) Year of manufacture: 2006 Factory number: 61482006 Load capacity: 125kg With Demag electric chain hoist 125kg Outreach: to be specified Condition: good Gjdozbyfuepfx Adcebn Available: from approximately August 2026 Location: Leipzig

Condition: good (used), Year of construction: 2009, Column-slewing crane, steel / Konecranes, 250kg, outreach 4.09m – used: Price (column with jib only) ex-works: €1,750.00 (net)! Manufacturer: Stahl / Konecranes Type: AS2.5-4.5 Year of manufacture: 03/2009 Factory number: PO10062432 Load capacity: 250kg Outreach: 4.09m Vertical pin distance: 850mm Approval No. 920309/01 Condition: good Available: from approximately August 2026 Godpezbyfhofx Adcjbn Location: Leipzig

Condition: good (used), Year of construction: 2024, Refrigerant dryer, OMEGA AIR, RDP 75 – used: Price ex works: €750.00 (net)! Manufacturer: OMEGA AIR Type: RDP 75 Year of manufacture: 2024 Nominal flow rate: 75 m³/h Max. operating pressure: 16 bar Ambient temperature during operation: 1 °C to 45 °C Max. air inlet temperature: 55 °C Ph~V-Hz: 1~230-50/230-60 | 0.40 kW Protection class: IP20 Contains fluorinated greenhouse gases Refrigerant: R513a | 0.39 kg | CO₂ equivalent 0.22 t Operating hours: unknown Condition: good Gbedpfx Adozbydwjcjn Available: from approximately August 2026

Condition: good (used), Year of construction: 1999, Screw compressor, Renner, screw compressor RS-PRO 7.5, soundproofed, incl. refrigerant dryer ECOTROC KTD-B100 – used: Price ex works: €2,950.00 (net)! Manufacturer: Renner Type: RS 7.5-10 Year of manufacture: 1999 Serial No.: 1992 Article number: 07500001 Rated power: Motor speed: Max. operating pressure: 10 bar Power consumption: 7.5 kW Gjdpfx Aszbydqedcjbn Delivery rate: 950 l/min Operating hours: approx. 4,342 h (as of 21.04.2026) Weight: 198 kg Incl.: Manufacturer: KSI FILTERTECHNIK Type: ECOTROC KTD-B100 Serial No: 31-11-MA11834 Max. pressure: 16 bar Nom. capacity: 97 m³/h Max. amperage: 2.1 amps Fuse amperage: 4.0 amps Refrigerant: R134a Refrigerant quantity: 0.75 kg Voltage: 230V / 1 / 50 Hz Power: 0.35 kW Condition: good Available: from approximately August 2026 Location: Leipzig

Condition: good (used), Year of construction: 2008, operating hours: 21,000 h, Screw compressor, Kaeser, Aircenter SX 6, compact all-in-one solution – used: Price ex works: €5,950.00 (net)! Manufacturer: Kaeser Type: Aircenter SX 6 Year of manufacture: 2008 Serial number: 1008 Rated power: 4.0 kW Motor speed: 2,910 rpm Max. operating pressure: 8.0 bar Ambient temperature: 3°C / 45°C Compressed air tank: 200 L Sound pressure level: Total weight: approx. 290 kg Dimensions (W x D x H): Width (mm): 590 Depth (mm): 1090 Height (mm): 1560 Options: K1 (refrigerant dryer) / T2 (voltage supply/transformer) Operating hours: approx. 20,210 h (as of April 21, 2026) Condition: good Available: from approx. August 2026 Gbjdpszbyc Hefx Adcon Location: Leipzig

Condition: good (used), Year of construction: 2013, operating hours: 48,000 h, Screw compressor, Kaeser, Aircenter SX 4, compact all-in-one solution – used: Price ex works: €4,500.00 (net)! Manufacturer: Kaeser Type: Aircenter SX 4 Gsdpfx Ajzbyctedcjbn Year of manufacture: 2013 Rated power: 3.0 kW Motor speed: 2,910 rpm Max. operating overpressure: 8.0 bar Ambient temperature: 3°C / 45°C Compressed air tank: 200 liters Sound pressure level: 60–61 dB(A) Total weight: approx. 285 kg Dimensions (W x D x H): 590 x 1090 x 1560 mm Options: K1 (refrigerant dryer) / T2 (voltage supply/transformer) Operating hours: approx. 46,997 h (as of April 21, 2026) Condition: good Available: from approx. August 2026 Location: Leipzig

Condition: used, mileage: 1,001 km, power: 59 kW (80.22 HP), first registration: 01/1955, fuel type: diesel, empty load weight: 3,580 kg, maximum load weight: 3,500 kg, overall weight: 7,080 kg, tire size: 8.25-20, axle configuration: 4x2, wheelbase: 3,250 mm, color: green, driver cabin: day cab, gearing type: mechanical, suspension: steel, loading space length: 3,400 mm, loading space width: 2,150 mm, loading space height: 550 mm, Year of construction: 1955, Equipment: cabin, trailer coupling, Vehicle location: Bovenden, Kz. Haus, switch 5, leaf suspension, AHK air-light-hydr. Wheelbase: 3250 mm Body: Truck vintage - 3-sided tipper swirl chamber diesel engine type EM4-20, 4-cylinder ( in-line ), 6024cm³, water-cooled, unsynchronized 5-speed gearbox, top speed: 60km/h, The successor model of the H3 was the H3A truck. It was presented to the public at the Leipzig Spring Fair in 1949 and built from mid-1950 to 1956 at the VEB Kraftfahrzeugwerk HORCH in Zwickau, initially as a platform truck. The H3A was a completely new development in its design as a long-hood truck with a diesel engine. The development of the diesel engine goes back to a VOMAG development for the Leipzig Spring Fair, the H3A appeared as a tractor unit with tank semi-trailer, other variants such as three-way tipper, livestock transporter, road tractor, tanker and with special bodies for the post office and DRK, as well as a furniture box. Around 180 H3B front-wheel-drive buses were produced at the LOWA plant in Bautzen on the basis of the H3A chassis. The main area of use was mainly in the civilian sector, but the H3A was also used by the Volkspolizei, or the barracked Volkspolizei, later NVA, Ex Dörr Spedition, errors excepted! ACCESSORIES WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! Gedpfx Adovhg R Tscjbn - .

Condition: used, mileage: 1,000 km, power: 59 kW (80.22 HP), first registration: 01/1955, fuel type: diesel, empty load weight: 3,580 kg, maximum load weight: 3,500 kg, overall weight: 7,080 kg, tire size: 8.25-20, axle configuration: 4x2, wheelbase: 3,250 mm, color: green, driver cabin: day cab, gearing type: mechanical, suspension: steel, number of seats: 2, loading space length: 3,400 mm, loading space width: 2,150 mm, loading space height: 550 mm, Year of construction: 1955, Equipment: cabin, trailer coupling, Vehicle location: Bovenden, Kz. house, switch 5, leaf suspension, AHK air-light-hydr. Gbjdpevhg Hnjfx Adcsn Wheelbase: 3250 mm Body: Truck vintage - 3-sided tipper body, swirl chamber diesel engine type EM4-20, 4-cylinder ( in-line ), 6024cm³, water-cooled, unsynchronized 5-speed gearbox, top speed: 60km/h, The successor model of the H3 was the H3A truck. It was presented to the public at the Leipzig Spring Fair in 1949 and built from mid-1950 to 1956 at the VEB Kraftfahrzeugwerk HORCH in Zwickau, initially as a platform truck. The H3A was a completely new development in its design as a long-hood truck with a diesel engine. The development of the diesel engine goes back to a VOMAG development for the Leipzig Spring Fair, the H3A appeared as a tractor unit with tank semi-trailer, other variants such as three-way tipper, livestock transporter, road tractor, tanker and with special bodies for the post office and DRK, as well as a furniture van. Around 180 H3B front-wheel-drive buses were produced at the LOWA plant in Bautzen on the basis of the H3A chassis. The main area of use was mainly in the civilian sector, but the H3A was also used by the Volkspolizei, or the barracked Volkspolizei, later NVA, Ex Dörr Spedition, errors excepted! ACCESSORIES WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! - .

Condition: used, mileage: 132,200 km, power: 77 kW (104.69 HP), first registration: 09/2018, fuel type: diesel, overall weight: 2,600 kg, color: white, gearing type: mechanical, emission class: euro6, number of seats: 3, total length: 4,972 mm, total width: 2,032 mm, total height: 1,964 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, Errors and prior sale excepted! Internal number: 1010. TA JM776 ----LOCATION: 04425 Taucha, Leipziger Str. 102 Tel. for inquiries: Mr. Ralph Bergel: By email: ----EQUIPMENT * Audio system 12 * Visibility package 1 * Seat package 4 + partition wall with window * Manual air conditioning * Transmission: 6-speed manual gearbox * ABS with EBD (Electronic Brakeforce Distribution) * Driver’s airbag * On-board computer * Flat roof * Headliner in driver’s cab * Double-wing rear door/180° (without window) * Tachometer * Electronic safety and stability system * Front electric windows * Cargo area lighting * Particulate filter: diesel particulate filter * Low beam headlights * Sliding door: sliding door, right * Side protection moldings * Power steering * Emergency brake assist * Seat belts * Air recirculation switch Gbodsumgcvspfx Adcjn * Lashing eyes * Immobilizer * Heat-insulating, lightly tinted glazing * Central locking with remote control ...and much more. ----Vehicle is in unprepared/as-is condition! Delivery nationwide available at extra cost. Errors and prior sale excepted. We are happy to take your vehicle in part exchange. Financing/Leasing also possible without down payment! Do you have any questions? We are happy to advise you!

Condition: used, Technical details: sheet width: 250 mm plate thickness: 2 mm number of rolls: 11 straightening feed: 5...30 m/min infeed height: 1250 mm total power requirement: 4,0 kW weight of the machine ca.: 620 kg dimensions of machine: 1,15x1,02x1,5 mm dimensions electric cabinet LxWxH: 0,66x0,53x0,32 m Band Leveling Machine with feed equipment: - sideways band guidance rolls Godpfx Adou Ic Ewscsbn model: - band intake height horizontal:1250mm - tiltable: positiv 30°; negativ 15° *

Condition: used, Year of construction: 1996, Technical details: x-travel: 762 mm y-travel: 510 mm z-travel: 560 mm control: Heidenhain TNC 415 OR 360 tool changer with: 21 place table clamping surface:: 865 x 510 mm table load: 455 kg tool taper: SK40 spindle revolutions per minute : 60 - 8000 U/min feed:: X/Y/Z; 15 000 mm/min rapid traverse : X/Y/Z: 24 m/min compressed air: Bedarf: 5,5 bar Total power requirement: 30 kVA motor capacity: Spindelmotor: 11,0 kW max. torque on the spindle: konstant: von 60 - 750 KN Weight approx.: 4,3 t dimension machine xH: 2,6 x 2,8 x 2,6 m dimension coolant device: L: 2,7 x B: 0,8 x H: 0,8 m Machining center with automatic tool changer IKZ and coolant supply through nozzles Gbodpfxeu Idmve Adcsn Chip and coolant tray Lubrication system through ball screws Manual control unit Heidenhain TNC 415 - dialog or according to ISO (machining cycles: deep hole drilling; tapping; slot milling; rectangular pocket and circular pocket milling; SL cycles), up to 100 programs in file management Machine can be visited with pleasure under power. i.D. *

Condition: used, Year of construction: 2002, Technical details: rated capacity: 1670 kVA rated capacity: 1500 KW voltage: 400 / 50 V / Hz Number of working hours: 800 h This UPS system is ideal for fault-free operation under the demanding environmental conditions that can occur in industrial applications. Suitable for stabilizing mains systems, for example. Gbsdpou Nzwuofx Adcjn The UPS system consists of the Powerbridge (a flywheel mass with attached generator) and a Uniblock (electric motor/generator block). The Uniblock supplies the power for the customer modules without grid faults. The Powerbridge serves as energy storage. In the event of a mains failure, the Powerbridge briefly takes over the power supply (at full load, the power supply is maintained for 39 seconds). Energy storage unit type PB60+ with bridging time 39sec. A diesel engine is connected via an overrunning clutch. This means that as soon as the engine has reached the speed of the Unibklock, it pulls the generator up to the synchronous speed and thus takes over the power supply. At the same time, the Powerbridge is supplied with energy again. *

Condition: used, Year of construction: 1995, Technical details: Table dimensions: 920 x 620 mm voltage: 220 / 50 V / Hz total power requirement: 0,77 kW weight of the machine ca.: 0,11 t dimensions L x W x H: ca.0,92 x 0,62 x 0,80 m Strapping Machine Semi-automatic machine for plastic strapping (approx. Ø 500 x 17mm) Strap holder located in the base cabinet table surface folded with 1,5mm chrome plate with stop LxWxH 345 x 80 x 20mm, adjustment approx. 32mm The adjustment of the tightening is done by display on linear scale. The packaging machine is mobile and easy to move = 4 castors, swiveling and 2 castors are braked. Gjdpfx Asvc Axcjdcjbn *

Condition: used, Year of construction: 1975, Technical details: turning diameter over bed: 500 mm turning diameter over support: 260 mm turning length: 950 mm center height measured in bed: 220 mm centre distance: 1000 mm revolution per minute: 11,2 - 2240 / 24 step U/min spindle bore of work spindle: 62 mm tailstock quill adjustment:: 210 mm longitudinal feeds:: 0,045 - 1,6 mm/U - 32 step cross feed: 0,02 - 0,71 mm/U - 32 step total power requirement: 11 kW Gjdsv A Sqhjpfx Adcobn weight of the machine ca.: k.A. t dimension machine xH: 3,3 x 1,2 x 1,6 m The machine is in a very good condition (very quiet spindle run) in Leipzig. Top slide rotatable 360° 3-jaw lathe chuck Ø 315mm with jaws (inside/outside) for speed 2000 rpm. Thread cutting: metric, modular thread, inch Chip protection wall Chuck protection (mechanical) MULTIFIX steel holder with Ø 40mm drill steel holder Chip collection tray Coolant supply with pump Protective device for lead screw Machine base UVV is pre-equipped ( UVV=Accident Prevention Regulations) *

Condition: used, Year of construction: 1996, Technical details: length: 4000 mm width: 800 mm height over floor: 400 mm Payload: 3,0 t dimensions L x W x H: 4,1 x 0,8 x 0,41 m weight: 0,153 t Several of these "long material trailers" are for sale in Leipzig. The trailers can be coupled together. The drawbar/trolley jack is charged separately, if required. Single axle operation with rigid axle. Solid rubber tires, track spacing = 590mm Godpfx Adju Nv Syocjbn Sale individually but also in a package from 5 pieces possible. Price on request. i.D. *

Year of construction: 2021, condition: used, Technical details: pressure: 5 t Gbjdpfx Adeyzzh Ejcon distance between columns: - mm dayligth: 60 mm rated capacity: 8 kVA table height adjustment: 60 mm compressed air: 6 bar connection voltage: 400 V electrics - voltage/frequency: 400/50 V/Hz total power requirement: 4 kW machine weight ab.: 610 kg SERVO-MECHANICAL SPINDLE PRESS Machine is programmable! MACHINE DESCRIPTION (2 machines available) MACHINE: Electrically driven press with a pressing force of 50,000 N The machine is designed for pressing bearings and rubber seals. It consists of a welded L-shaped frame. A movable press table is mounted on the horizontal arm, which can be manually adjusted along linear guides. In the front position, the table can be manually locked using a spring-loaded pin. In the working position (under the press head), the table is automatically locked by a pneumatic cylinder. The press head can only be lowered using two-hand operation when the table is in this position. The control panel includes: ·Two-hand control switches ·Emergency stop switch ·Table lowering button ·Force selection switches (1, 2) The pressing force can be adjusted using potentiometers in the control cabinet. Two force levels and the corresponding pressing speed can be set there. The press head moves along the vertical arm of the press on linear guides. It is driven by a lead screw, powered by an electric motor with gearbox via pulleys and a timing belt. The entire machine is mounted on a table made of aluminum profiles. *

Condition: used, Year of construction: 2021, Technical details: feed pressure: 8 bar liter capacity: 620 l total power requirement: 4 kW sound level: 63 dB(A) revolutions per minute of the motor:: 920 Number of cylinders: 2 electrics - voltage/frequency: 400/50 V/Hz Pressure max.: 14,5 bar Number of working hours: 2195 h machine weight approx.: 194 kg dimensions L x W x H: 1,24 x 0,85 x 1,20 m Gbjdoxrdw Ispfx Adcjn Professional, soundproofed compressor with the lowest noise level in its class, designed to eliminate noise problems in working environments. The powerful 5.5 hp pump unit guarantees maximum efficiency and reliability. It is also equipped with an additional intake silencer, a belt tensioning device that regulates belt tension and facilitates replacement, and a forced ventilation fan for better cooling. The control panel with star-delta start control is positioned for easy reading and operation. The opening front door allows for easy maintenance. *

Condition: used, Technical details: operating hours: 2151 h milling spindle operating time: 2 h turning spindle switch on : 709 h swing diameter: 1000 mm turning diameter: 900 mm workpiece height max.: 800 mm control: Mazatrol Smoothg x-axis: 470 mm z-axis: 876 mm c-axis: 20 m/min tool holder / places: 12 revolution per minute: Revolver 4000 U/min workpiece weight: 3000 kg rapid power traverse in X-and Z direction: 24 m/min weight of the machine ca.: 14 t dimension machine xH: 3989 x 2375 x 3400 mm Gbjdpfxjydvfcs Adcon

Year of construction: 1998, condition: used, Technical details: profile width: 50 mm work height max.: 950 mm interface: RS 232 Pinout Window profile processing machine for materials such as plastic, aluminum and wooden windows in a continuous process. The materials are conveyed by a pneumatic transport and clamping system. The system consists of two work stations (machines), an electrical control cabinet, and a control panel and transport units. As well as columns with transport system vibrator, chip transport unit and column with receipt printer. Our photos are first taken from the location and then further pictures are how the plant is stored in our stock ready for transport. Workstation no. 1 (machine 1): -sawing station with saw blade Ø 400 x 4,5mm -drilling unit with clamping cartridge (vertical upwards) -drilling unit with clamping cartridge (hotizontal) -Boring with clamping cartridge (vertical down) -twin drilling unit with clamping cartridge (vertical down) -45° drilling unit with clamping cartridge (upwards) Working station no. 2 (machine 2): -drilling unit with clamping cartridge (vertical upwards) -milling spindle horizontal with 11 side milling cutters -Drilling unit with clamping cartridge (vertical down) -Drilling unit with clamping cartridge (vertical upwards) -Drilling unit with clamping cartridge horizontal 2 transport units: motor driven -LxWxH: 5.650 x 2.400 x 1.000mm -track width 1.980mm 2 pieces transport units: motor driven -LxWxH: 2.150 x 2.750 x 1.050mm Godpfju Ibuwox Adcjbn -track width 2.300mm *

Condition: used, Year of construction: 1985, Technical details: Gbsdpfxeu Nfh Do Adcen pressure: 100 t no. of strokes: 35-100 Hub/min throat: 360 mm ram adjustment: 20-130 mm ram surface area: 750x550 mm clamping plate on table: 1000x640 mm adjustment of stroke: 90 mm passage between the columns longitudinal/sideways: 610x500 / 440x550 mm daylight dimension : table/slide low: 300 mm total power requirement: 17,5 kW weight of the machine ca.: ca,7,0 t dimension machine xH: 1,9x1,4x2,7 m - there are 5 T-slots lengthwise on the ram plate - centre hole = 50mm This press is currently for sale without controls. Optional on customer request completion possible. i.D. *

Condition: new, This is a new machine which is manufactured in Romania by the manufacturer Emsil. Customer wishes can be taken into account depending on technical implementability and are checked in advance by the manufacturer's engineering office. Narwhal features a drilling spindle that is made of hardened, tempered and rectified alloy steel. It is mounted with preloaded oblique precision ball bearings. The machine is also equipped with a milling and boring bar which can handle exceptional power and torque. The bar is made of nitrided alloy steel and is also mounted with oblique preloaded precision ball bearings. It moves on bronze guide bushings. Gbsdpfxeu Id H As Adcjn The clamps of both units, used for securing and releasing the tool holder cone with ISO 50 coupling, open and close automatically Rotary Turntable: The table is turned by means of a double pinion gearbox, a central rod wth bearings and hydrostatic sliding block of the centre bearing which is of a suitable size to guarantee maximum precision with large loads, even unbalanced ones. There is a recirculating ball screw slide guide system for the x-axes. Both axes are equipped with a direct measuring system. CNC Axes Control: The 9 axes of the machine are monitored at all times. The monitoring system is equipped with a 15'' TFT screen, a control panel, remote diagnostics that alert the user in case of faults, a user memory, network connectivity, remote control of the process, integrated PLC, etc. The machine is compatible with the multiple control systems such as Heidenhain, Fanuc, Siemens etc. You can choose the sizes of machining of X/Y and Z axes: from 1200 - 3500 / 1000 - 3500 / 400 - 1500mm *

Condition: used, Year of construction: 1993, Technical details: material: PUR Schaum Rotor-Ø: 315 mm compressed air: 6 bar The milling plant with milling and opening-up machine REKORD BR-ex Gbedpou Nxdfsfx Adcjn (explosion proof up to 3 bar absolute) is intended exclusively for grinding PUR (polyurethane) foam. Data of the processable material: - pre-comminuted PUR foam pieces max. 20mm - humidity so that milling is still possible - throughput volume=approx. 130kg/h Drives: - 5 drives (all geared motors) for roller dosing units, mill drive (squirrel cage motor), mixer, discharge screw conveyor, bucket wheel *

Condition: used, Year of construction: 2023, operating hours: 15 h, ATTENTION: Sunward machines are being offered that are not genuine. These are replicas under different names, advertised as Sunward successors or new models. Please verify whether the dealer is officially listed and whether the machine on offer has an official Sunward nameplate. Anything else is a replica not associated with Sunward. We are the official Sunward dealer responsible for the following regions: Berlin, the state of Brandenburg, and Eastern Saxony. Gbjdpfeyq A N Ujx Adcjn Sunward SWE08B Year: 2023 Approx. 15 hours – demonstration machine Operating weight: 980 kg Adjustable undercarriage: 750 mm to 1000 mm LED work lights 2 travel speeds Includes MS01, 25 cm and 60 cm digging buckets Net price: €13,900.00 Inspection possible at any time by appointment over the phone. All information provided without guarantee. We accept trade-ins of your used machine. We are Sunward dealer for the following regions: District of Wittenberg, District of Nordsachsen, District of Leipzig, City of Leipzig, District of Elbe-Elster, District of Oberspreewald-Lausitz, City of Cottbus, District of Spree-Neiße, District of Oberhavel, District of Barnim, District of Märkisch-Oderland, City District Frankfurt (Oder), District of Oder-Spree, District of Dahme-Spreewald, District of Teltow-Fläming, District of Potsdam-Mittelmark, City of Potsdam, City of Brandenburg, District of Havelland, City of Berlin.