Used Gratings for sale (379)

Condition: excellent (used), CTS Temperature test chamber T-55/1000 Li water-cooled Temperature range: -50°C to +100°C Rated voltage: 400V 3/N 50Hz Rated power: 9.5 kW Nominal current: 18 A Compressor: TFH2511Z / TFH2511Z Refrigerant R404A/R23 The type designation of the CTS cabinet series is composed as follows: z. e.g. type T -55/1000/Li 1) T means: temperature 2) -55 means: lower temperature -55 °C 3) 1000 means: 1000 liter test chamber volume 4) Li means: special equipment for tests with lithium-ion accumulators Control: 32 bit controller LCD control panel Digital display of set and actual values Numerical input of setpoints Error messages in plain text Ethernet interface RS 232 interface Free switching channels for on-site test material control Test room lighting: energy-efficient, high-intensity LED light strip mounted on the door Insert grid: Cgedpfxsvba Ras Aa Nep Stainless steel, support surface 970 x 980 mm Load per shelf max. 35 kg Total load with max. grating load 100 kg 1a Feed-through NW50 1b Feed-through 2x NW125 1c Entry port 2x Rp 314° for Minimax Technical performance data: Temperature tests: Temperature range -50°C to +100°C Temperature deviation ≤ ±0.3 K in time Temperature change rate according to IEC 60068-3-5 Heating 2.5 K/min Cooling 2.5 K/min Heat compensation approx. 4000 W at +20°C approx. 2200 W at -40°C The technical data refer to an ambient temperature of +25 °C, rated voltage 400V, without test material, without heat compensation and without additional equipment. Options may affect the performance data. Dimensions: Test volume 1000 liters Test chamber dimensions Height, approx. 1000 mm, width, approx. 860 mm, depth, approx. 1100 mm External dimensions Height, approx. 1950 mm, width, approx. 1270 mm, depth, approx. 1900 mm Operating data: Electrical connection 400 V +6/-10 %, 3/N, 50 Hz Nominal current 18 A Rated power 9.5 kW Protection class IP 54 Sound pressure level < 58 dB(A) (according to DIN EN ISO 3744 measured at a distance of 1 m from the front) Mass approx. 1000 kg Heat output to the installation room 10.4 kW Cooling unit: water-cooled, low-noise, fully hermetic Infinitely variable output adjustment via electronic monitoring and control system, environmentally friendly refrigerant R404A/R23 The following information is for your safety as a buyer! The following points are carried out on our offered chambers in advance: 1. functional check and replacement of necessary components 2. if necessary, refilling with legally compliant refrigerant 3. leak test with certificate 4. after successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Year of construction: 2023, condition: like new (used), Thermo Fisher Type: ARL easySpark metal analyzer Analysis table spectrometer with PC, monitor and software Thermo Scientific OXSAS 2.7 software OXSAS is the most modern software for optical emission spectrometers. Current analyses are displayed in tabs. Immediate editing of data sets using fill-down and increment-down tools OXSAS is a multi-processing application with amazing capabilities and potential. The comprehensive functionality of OXSAS enables it to meet all your requirements. Technical machine description: Condition: fully functional In mint condition Year of manufacture: 02/2023 Technical description of the system: The ARL easySpark metal analyzer is designed to meet the challenges and requirements of small to medium-sized plants and laboratories in the metal industry that require high-quality but cost-effective OES analysis for the production of parts for the automotive, aerospace, consumer goods and other industries. The device impresses with its particularly high resolution thanks to a unique optical system based on multi-grating/CCD (charge-coupled device). Additional benefits of the Thermo Scientific ARL easySpark analyzer include: The ability to accurately analyze all elements, from trace levels to percent, in all solid metal samples A breakthrough spark excitation and optical design to ensure best-in-class performance Intuitive, user-friendly Thermo Scientific OXSAS analysis software for a quick learning curve and easy routine operation A robust and reliable design that requires minimal maintenance Compliance with safety and quality guidelines A simple design that is suitable for both novice production users and expert lab staff The instrument is ideal for other areas such as metal recycling, academic and non-academic laboratories and primary metal producers where a cost-effective solution for analyzing metal products and materials for quality assurance and process control or a secondary instrument is required. Power connection: 110-230 VAC, 50Hz or 60Hz Max. power: 600 VA Dimensions: Approx. L x H x D 0.80m x 0.45m x 0.70m Cgedov Hbvbepfx Aa Nep Weight: Approx. 80 kg Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have over the phone.

Condition: excellent (used), Weiss temperature chamber Here we offer a Weiss temperature chamber. Cjdpfx Aop Dun Uea Nogp Weiss temperature chamber air cooled with Weiss condenser cooler Test chamber capacity approx. 990 liters Data for temperature tests: Temperature range -40°C to +180°C Temperature deviation in time in center of chamber ± 0,1 to ± 0,5 K Temperature deviation spatially ± 0.5 to ± 2.0 K Temperature gradient (acc. to IEC 60068-3-5) 1 to 4 K Temperature change rate (according to IEC 60068-3-5) Heating 4 K/min Cooling 3 K/min Heat compensation max. 4500 W Feedthrough built into basic equipment R1: NW 125 mm L1: NW 50 m Dimensions: Test chamber dimensions: Width 1100 mm x depth 950 mm x height 950 mm Housing dimensions: width 1390 mm x depth 1525 mm x height 1995 mm maximum load (evenly distributed over the surface) of the test chamber floor 150 kg per insert grate 50 kg total load of the grate supports 100 kg Data for operation: Test room lighting halogen bulb 24V, 50W Rated voltage 3/N / PE AC 400 V ± 10% 50 Hz Rated power 11,5 kW Rated current 22 A Heat output water-cooled test chambers max. heat output to environment 1.3 kW Noise measurement: Sound pressure level approx. 64 dB(A) Refrigerant: ( converted to R-452a ) weight: approx. 840 kg Type: WT11-1000/40 For you as a buyer for safety the following information! The following points are carried out on our offered chambers in advance: 1. functional check and exchange of necessary components 2. new filling with legally compliant refrigerant 3. leak test with certificate 4. after successful inspection, the chambers are subjected to a test run, which is monitored with calibrated equipment. Condition: used / used Scope of delivery: (See picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: excellent (used), Weiss temperature test chamber Here we offer a temperature test chamber. Weiss temperature test chamber water cooled Technical data: Codpfx Ajiqk Absa Nogp Test cabinet designation: WT-600/70 Outer dimensions with hinges and door lock height 1995 mm, width 1090 mm, depth 1660 mm Outer dimensions without hinges and door lock height 1995 mm, width 1000 mm, depth 1660 mm Internal dimensions: Height 950 mm, width 800 mm, depth 800 mm Test chamber capacity: approx. 600 liters cold / heat operation -70°C to 180°C Temperature change per time cooling approx. 2.5 K/min Heating up approx. 4 K/min 3/N/PE AC 400V ±10% 50Hz Rated power: 9.1 kW Rated current: 19 A Fuse on site: 32 A slow blow Permissible test material weight Total load of grate supports 80kg test chamber floor 80kg, insert grate 40kg Refrigerant: R 404A/R23 Weight: 675kg Type: WT-600/70 For you as a buyer for safety the following information! The following points are carried out on our offered chambers in advance: 1. functional check and exchange of necessary components 2. new filling with legally compliant refrigerant 3. after successful inspection, the chambers are subjected to a test run, which is monitored with calibrated equipment. Condition: used / used Scope of delivery: (See picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: excellent (used), Optical emission spectrometer Ultima 2 benchtop device, sequence spectrometer with a 1m monochromator, 2400 g/mm grating in first and second order 160-800 nm without image Quick overview analysis IMAGE: Quick overview analysis IMAGE NAVIGATOR for JY 2000-2, JY Ultima 2 or JY Ultima 2C External closed cooling circuit for cooling the Ultima 2's HF coil Argon humidifier - for analyzing solutions with a high salt content. ULTIMA 2 ICP-OES - Optical Emission Spectrometer reliable high-efficiency 40.68 MHz semiconductor generator complete and precise wavelength scan from 160 to 800 nm as standard Cgodpfx Ajur Rmvsa Nep highest practical resolution

Condition: used, Year of construction: 1993, functionality: limited functionality, nominal heat output: 500 kW (679.81 HP), heating capacity: 500 kW (679.81 HP), operating pressure: 4 bar, Equipment: type plate available, Urbas reciprocating grate heating system with primary and secondary blower, cyclone, hydraulic fuel discharge with push rod (no auger), all hydraulically operated for coarse material. Some boiler passes are welded. Complete with control unit, has been in operation until now; plant is being dismantled due to relocation. Fireclay lining in very good condition. Cjdoyk Sgcjpfx Aa Negp

Condition: used, Year of construction: 2022, functionality: fully functional, total width: 3,670 mm, total height: 17,685 mm, overall weight: 9,250 kg, 2 pcs. KURZ steel sheet silos with tubular supports, manufactured from S235JR+AR, designed for pneumatic filling and central discharge. Including: ladder, railing, cartridge filter, silobarometer DN150, pressure switch for surge limitation, rotary paddle level indicator. Bulk material: cement Bulk density: 1.2 t/m³ Bulk density for structural analysis: 1.6 t/m³ Properties: dry, free-flowing, fluidizable, non-combustible Design pressure: non-pressurized Explosion protection (ATEX): not provided Bulk material load according to Eurocode EN1991-4 Seismic loads: Zone 4 per ÖNORM, agR=1.08 m/s² Wind loads as per Eurocode EN 1991-1-4, Wind zone 2, Terrain category "inland" Nominal diameter: 3,500 mm Geometric capacity: 141 m³ Cylinder height: 14,000 mm Cone angle: 54° Cone height: 2,060 mm Cgjdpfx Aaeymlq Ts Njp Total height: 17,560 mm Support center distance: 2,470 x 2,470 mm Connections: - Filter flange on silo roof - Inspection opening DN600 on roof (with hinged cover and grating) - Filling pipe DN100 internal, with A-fixed and blank coupling - Deflector plate as wear protection - Break cone in silo cone above outlet - Moisture deflection ring on silo cone - Outlet flange DN300 €26,000 / unit

Condition: excellent (used), functionality: fully functional, Pomac Cyclone Installation with Pump System Cgodoyku Nyepfx Aa Nop Pump brand: Pomac Overall dimensions: Height 4000 mm Technical specification: - Drum screen: dimensions 1000 x 1800 mm - Collection tank: stainless steel, dimensions approx. 1270 x 1880 x 1350 mm - Circulation pumps (2 pcs): Pomac brand, made of stainless steel - Pump capacity: 35 m³/h each, pressure 4 bar Construction: - Equipped with a protective cover - The entire system is mounted on a robust steel frame - Supplied with a grated floor (platform) and access stairs The cyclone installation is an advanced liquid separation and circulation system, designed for effective process water purification or solids separation in the food industry. The use of two high-performance Pomac stainless steel pumps ensures stable flow and the required operating pressure for filtration processes. Thanks to the integrated design with platform and stairs, the unit provides safe and ergonomic service operation at elevation.

Condition: excellent (used), functionality: fully functional, Odenberg / Tomra Potato Sorting Line Brand: Odenberg / Tomra Control System: “Tomra” Touchscreen Panel Technical Specification: - Optical Sorter: Odenberg with mechanical finger ejection system - Infeed Hopper: steel construction, with side and top inlets - Conveying System: rising inclined conveyor belt, overhead feed conveyor belt - Water Section: 2 submersed conveyor belts - Feeding Section: cross-flow feed with vibrating grate and conveyor belt - Installation footprint: Cgjdsyku I Njpfx Aa Nsp Total usable floor area: 10,500 x 4,750 mm Set includes platforms with slatted flooring An advanced potato sorting line based on Odenberg and Tomra optical technology, providing a complete solution for modern processing facilities. At the heart of the system is a precision optical sorter with mechanical ejection, operated by the intuitive Tomra interface, enabling rapid product selection by quality and size. A unique feature of the line are the two underwater conveyor belts, ensuring extremely gentle handling of the produce and minimizing bruising and mechanical damage.

Year of construction: 2019, condition: excellent (used), functionality: fully functional, DTS Bend Screen – Stainless Steel Curved Sieve Brand: DTS Type: Bend screen (slot/curved screen) Year of manufacture: 2019 Cgjdoyku E Iepfx Aa Njp Overall dimensions: 700 x 1300 x 2800 mm Working width: 650 mm Intended for first-stage separation Without platform and grating floor The DTS steel bend screen is a modern machine designed for high-performance separation of solids from liquids in industrial processes. Thanks to its 'Bend Screen' construction with a 650 mm working width, this unit is ideal as the first stage of process water treatment or raw material recovery. The machine utilizes gravitational liquid flow across the curved screening surface, providing effective solids separation without the need for mechanical drives in the filtering section.

Condition: excellent (used), functionality: fully functional, DTS Double Screw Blancher, Stainless Steel Brand: DTS Year of manufacture: 2004 Power supply: 400 V Technical specifications: - Steam-heated system - Operating pressure: 6 bar - Screw dimensions: approx. Ø 1200 x 5000 mm - Water capacity: 1x 4.41 m³ and 1x 3.39 m³ Discharge conveyor: - Steel, dimensions: 4800 x 500 mm Total footprint: 8500 x 4300 mm Machine without platform, stairs, or grating floor Cgodpeyku D Djfx Aa Nsp The DTS double screw blancher set is an advanced processing unit made entirely of stainless steel, designed for the thermal treatment and conveying of food raw materials, especially potatoes and root vegetables. Featuring a high-pressure (6 bar) steam heating system and large operational capacity, this set is ideally suited for blanching, steaming, or pre-processing in high-throughput production lines. The use of two independent, large-diameter screws ensures accurate retention time control for the product, resulting in consistent processing quality while minimizing the risk of mechanical damage to the raw material.

Condition: new, High quality grating supports with high load capacities, low priced alternative for grating - new -. Prices on request! Manufacturer: Delta Shelving Type: Manta Mesh Standard width: 885mm (for a 2,70m truss then 3 supports are needed = 2.655mm) 1335mm Frame depths: 1,05m 1,10 1,20m Other depths on request! Uniformly distributed load: between 250 and 1.500kg Standard (price applies to the standard version): 1.000kg, i.e. also per pallet Grid size: 50 x 100 or 25x100mm Please also indicate which type of beam (truss type) you have when making an inquiry! So whether box profile (or IPE beam) 50 or 40mm, or whether you have trusses with step. Cgsdpfxjiuvxbj Aa Njp Advantages: no sharp edges 200% safety factor - independent of the rack beams Can be tested for permissible deflection and structural failure Wide range of standard sizes and load capacities MantaMESH is our market leading wire mesh shelving solution. MantaMESH delivers certainty with more than 70% open area and a 200% safety factor that exceeds the requirements for ANSI MH26.2 - 2007, NFPA 13 and the FM Global Approval Standard for ESFR Sprinklers. Compatible with ANSI MH 26.2 - 2007 Manufactured in Germany Pre-welded seamed support channels Pre-galvanized finish Maximum deflection independent of rack beams: 1100 mm deep: 6.67 mm at 1000 kg load Load at structural failure independent of support beams: 1100 mm deep: 2000 kg Mesh has more than 70% open area Example configuration - we will be happy to create a configuration for your application!!! Depth 1102mm width 881 mm 4 pre-welded support channels 50x100mm mesh size 1000 kg UDL independent of the support beams Front: fold 30mm outwards Rear: Fold outside 30mm downwards Item weight 9.43kg

Condition: excellent (used), functionality: fully functional, Screen / Sorting device with Cornell tanks Consists of: - Screen belts (2 pcs): working width: 750 mm - Roller table: working width: 1500 mm - Stainless steel tanks (2 pcs): dimensions: 1580 x 1060 x 1170 mm equipped with "Cornell" brand pumps The device is offered without platforms or grating floors. Cgedpfx Aeykmirea Nop The screen / sorting device is an advanced system designed for the preliminary selection and transport of products in the food industry. The construction, based on two screen belts and a wide roller table (1500 mm), enables efficient sorting of raw material and removal of impurities or small fractions. A key element of the set are two robust stainless steel tanks, integrated with high-performance Cornell pumps, allowing operation in systems requiring hydraulic transport or intensive product washing.

Condition: used, Year of construction: 1996, Wood chip heating system Fröling Lambdamat 1000kW + 320kW – Feed grate combustion for low fuel quality, output 1000kW + 320kW, year of manufacture 1996, hot water system max. temperature 95°C, 3 bar, incl. pneumatic cleaning for 1000kW unit, incl. flue gas dust separator – multicyclone separator with ash container, incl. feed screw for each unit, incl. common control system. Pusher floor not included! Dismantling must be carried out by the buyer. Roof will be opened! Components can be removed with a crane over the roof. Codjvyrwpjpfx Aa Nsgp

Condition: new, mileage: 100 km, power: 375 kW (509.86 HP), fuel type: diesel, gearing type: automatic, axle configuration: > 3 axles, overall weight: 32,000 kg, loading space length: 9,000 mm, loading space width: 2,550 mm, emission class: euro6, color: white, Year of construction: 2026, Equipment: ABS, air conditioning, navigation system, parking heater, 4-axle Volvo machine/MEWP transporter FH 500 8x2R - Trailing axle, electro-hydraulically steered, single tires - Rear axle suspension with air suspension: 1 drive axle, 1 trailing axle - High-safety long-distance FH cab - Cab auxiliary heater, 2 kW - 33 l refrigerator with freezer compartment, under bunk - Air suspension on front axle(s) - Gearbox/I-Shift operated via driver's seat control unit - I-Shift drive modes: Standard, Performance, and Economy - I-See with map-based topography and traffic information - Eco Cruise Control (cruise control) including brake cruise control - Manual gear selection possible in automatic mode (incl. kickdown) Adaptive traction control - Adaptive cruise control (ACC) with collision warning and emergency braking - Lane keeping assist - Side collision avoidance and turn assist (both sides) - Driver alert system warns of fatigue - VEB Volvo engine brake - etc. WIESE body for MEWP and construction machine transport with hydraulic loading ramps With 2 pairs of wheel recesses including covers Body dimensions: - Length: approx. 9,050 mm usable - External width: 2,550 mm - Loading height top of floor: approx. 1,050 mm unladen - Robust, weight-optimized welded steel construction, box-section design - Short cross member spacing for high point loads - Tapered rear for low ramp angle - Outer frame profile 90° - Front wall in reinforced version - Internal toolbox at the bottom in front of front wall - Grating floor - Designed for 5,000 daN wheel load - Steel sheet boxes above axles and outer frame with anti-slip coating Load securing: - 9 pairs of heavy-duty lashing rings, 8 to., recessed into outer frame - Longitudinal members each with Multi-X contour along full length with numerous 2.5 to. lashing points - 4 lashing eyes 8 to. recessed at rear (left/right/center/center) - 4 lashing eyes 8 to. recessed in front wall (left/right/center/center) - Outer frame profile 90° Loading ramps: Type: WFB 20 S-2 Load capacity: 18,000 kg per pair Platform length approx.: 4,360 mm (2,725 mm + 1,635 mm) Platform width approx.: 850 mm per ramp - Ramps as 2 individual/extendable units, both ramps laterally adjustable - Ramp can be used as drive-on ramp and as through ramp for warehouse equipment (extension section remains closed), the fixed ramp part is placed on the loading dock - Robust tension bar for transport securing (alternative: strap tensioning) - 2 hydraulic rear supports with pads, with warning buzzer and indicator in cab - Ramp and support operation via electro-hydraulic system - Remote control and emergency control on the control block - Stainless steel control box mounted on frame side - Superwinch 8.2 t with approx. 20 m steel cable - Step access with grab handles left/right for cargo area access - 5 stainless steel drawer-type toolboxes, incl. lighting (option, extra charge) - Side skirting as per sample pictures (green vehicle) optional, extra charge - KTL body coating Cgjdpfx Aew Itmrja Nop - Trailer coupling with 3.3 t ball head at rear - 4 LED work lights - 2 LED taillights mounted high on front wall - 4 external LED work lights on frame as area illumination - 2 LED work lights at rear - 1 removable rotating beacon at rear The stock vehicle is supplied with cab in white and body in nova grey (external frame painted in RAL color of your choice on request).

Condition: new, mileage: 100 km, power: 375 kW (509.86 HP), fuel type: diesel, overall weight: 32,000 kg, axle configuration: > 3 axles, color: white, gearing type: automatic, emission class: euro6, loading space length: 9,000 mm, loading space width: 2,550 mm, Year of construction: 2026, Equipment: ABS, air conditioning, navigation system, parking heater, 4-Axle Volvo Machine/Platform Transporter FH 500 8x2R - Tag axle, electro-hydraulically steered, single tires - Rear axle suspension with air suspension: 1 drive axle, 1 tag axle - Safety long-distance driver cab FH - Cab autonomous heater, 2 kW - 33 l refrigerator with freezer compartment, under bunk - Air suspension on front axle(s) - Transmission / I-Shift control via driver's seat control unit - I-Shift driving modes: Standard, Performance, and Economy - I-See with map-based topography and traffic information - Eco cruise control (cruise control), including braking cruise control - Manual shifting possible in automatic mode (incl. Kickdown, adaptive traction control) - Adaptive cruise control (ACC) with collision warning and emergency braking - Lane keeping assist - Side collision avoidance and turn assist (on both sides) - Driver alert system for fatigue warning - VEB Volvo Engine Brake - Etc. WIESE body for platform and construction machine transport with hydraulic loading ramps - With 2 pairs of wheel recesses incl. covers Body dimensions: - Length approx. 9,050 mm usable length - External width 2,550 mm - Loading height to upper edge of floor approx. 1,050 mm unladen - Sturdy, weight-optimized welded steel construction, volume design - Short cross member spacings for high point loads - Rear tapered for low approach angle - Outer frame profile 90° - Front wall, reinforced version - Storage box inside, below the front wall - Grating floor - Designed for 5,000 daN wheel load - Above the axles: steel sheet boxes and outer frame with anti-slip coating Load securing: - 9 pairs of heavy-duty lashing rings, 8 t, recessed into the outer frame - Longitudinal beams with continuous Multi-X contour along the full length with numerous 2.5 t lashing points - 4 lashing eyes, 8 t, recessed at the rear (left/right/center/center) - 4 lashing eyes, 8 t, recessed in front of the front wall (left/right/center/center) - Outer frame profile 90° Loading ramps: Type: WFB 20 S-2 Load capacity: 18,000 kg per pair Platform length approx.: 4,360 mm (2,725 mm + 1,635 mm) Platform width approx.: 850 mm per ramp - Ramps as two individual/extendable pieces, both laterally adjustable - Ramps can be used as approach ramps or as drive-through ramps for material handling equipment (extension section remains closed), fixed section placed onto the building ramp Cgjdpfx Aasw Itl Us Nop - Sturdy locking bar for transport security (alternative with belt tension) - 2 hydraulic rear supports with pads, buzzer and control light in cab - Ramp and support operation via electro-hydraulics - Control via radio remote control and emergency operation at the control block - Control block mounted in stainless steel tool box at side of frame - Superwinch 8.2 t cable winch with approx. 20 m steel cable - Access steps with handrails right and left for access to load area - 5 stainless steel toolboxes in drawer design, incl. lighting as option (surcharge) - Side panels as per sample pictures (green vehicle) optional (surcharge) - Body coating KTL - Ball hitch at rear, 3.3 t - 4 LED work lights - 2 LED rear lights mounted high at the front wall - 4 LED work lights on frame sides as ambient lighting - 2 LED work lights at the rear - 1 removable rotating beacon at rear The stock vehicle comes with white cab and superstructure in Novagrau (outer frame paintwork according to RAL color of your choice upon request, price on application).

Condition: new, mileage: 100 km, power: 375 kW (509.86 HP), fuel type: diesel, overall weight: 32,000 kg, axle configuration: > 3 axles, color: white, gearing type: automatic, emission class: euro6, loading space length: 9,000 mm, loading space width: 2,550 mm, Year of construction: 2026, Equipment: ABS, air conditioning, navigation system, parking heater, 4-axle Volvo machine transporter/platform lift transporter - FH 500 8x2R - Tag axle, electro-hydraulically steered, single tires - Rear axle suspension with air suspension: 1 drive axle, 1 tag axle - FH high safety long-distance cab - Cab auxiliary heater, 2 kW - 33 l refrigerator with freezer compartment under the bunk - Air suspension on front axle(s) - Transmission/I-Shift operation via control unit on driver's seat - I-Shift driving modes: Standard, Performance, and Economy - I-See with map-based topography and traffic data - Eco cruise control (cruise control) including brake cruise - Manual shifting in automatic mode possible (incl. Kickdown) Adaptive Traction Control - Adaptive Cruise Control (ACC) with collision warning and emergency braking - Lane keep assist - Side collision avoidance and turning assistant (both sides) - Driver alert system warns of fatigue - VEB Volvo Engine Brake - etc. WIESE body for platform lift and construction machinery transport with hydraulic loading ramps Includes 2 pairs of wheel recesses incl. wheel recess covers Body dimensions: - Length approx. 9,050 mm useable length - External width 2,550 mm - Loading height top of floor approx. 1,050 mm unladen - Sturdy, weight-optimized welded steel construction, box section design - Short crossmember spacing for high point loads - Rear end tapered for low approach angle - Outer frame profile 90° - Front bulkhead reinforced version - Storage box inside front lower area - Grated floor - Designed for 5,000 daN wheel load - Steel toolboxes above the axles and outer frame with anti-slip coating Load securing: - 9 pairs heavy-duty lashing rings, 8 t, recessed into outer frame - Side rails each with Multi-X contour along entire length with multiple lashing points 2.5 t - 4 lashing points 8 t recessed at rear (left/right/center/center) - 4 lashing points 8 t recessed at front/bulkhead (left/right/center/center) - Outer frame profile 90° Loading ramps: Type: WFB 20 S-2 Capacity: 18,000 kg per pair Platform length approx.: 4,360 mm (2,725 mm + 1,635 mm) Platform width approx.: 850 mm per ramp - Ramps as 2 individual/extendable ramps, both ramps laterally adjustable - Ramp can be used as loading ramp or as cross-over ramp for warehouse use (extension part remains closed), fixed ramp section lays onto loading bay - Sturdy locking bar as transport security (optionally with belt system) - 2 hydraulic rear stabilizers with support plate, warning tone, and indicator light in cab - Ramp and support operation by electro-hydraulic system - Control via wireless remote and emergency controls on manifold - Control manifold mounted in stainless steel toolbox on chassis side - Superwinch winch 8.2 t with approx. 20 m steel cable - Access steps with handrail right and left for deck access - 5 stainless steel toolboxes in drawer version, with lighting as optional extra - Side skirts as per sample photos (green vehicle) as optional extra - Body coating KTL - Ball-type trailer hitch at rear, 3.3 t - 4 LED work lights - 2 LED rear lights mounted at top of bulkhead - 4 LED work lights on outer chassis as perimeter lighting - 2 LED work lights at rear - 1 removable beacon at rear The stock vehicle is finished with a white cab and 'Novagrau' body (outer frame coated in RAL color of your choice on request). Cgsdpew Itmlefx Aa Nep

Condition: excellent (used), Transition / Stairs / Crossover, 3 stairs - used- : Price ex location: 1.950.-€ (net), dismantled, packed and loaded! The position of the stairs on the platform can be changed. Manufacturer: unknown Type: unknown Year of construction: unknown Gratings Dimensions: Platform height: approx. 1.60m Platform width: approx. 1m Platform length: approx. 3.65m (length outside incl. railing: 3.73m) Length: Stairs: approx. 2.10m Stair width: approx. 90cm Step spacing: approx. 20cm Step depth: approx. 26cm Step width: approx. 80cm Railing height: approx. 1.10m Gap between the landing supports: approx. 2.35m Condition: good - very good Cedpfjrdfwuox Aa Njgp Available: immediately Location: Biebergemünd Biebergemünd

Condition: good (used), Used stainless steel agitator vessel with double jacket Item number: 10492 Final use: food Volume: approx. 1400 litres Type: Standing on 4 feet Material (wetted): 1.4301 stainless steel Design: With double jacket Manhole: 1250x420mm Hinged cover on both sides Base: Vaulted Top panel: Hinged lid Operating pressure according to type plate: ATM Tank dimensions: Outside diameter: 1460mm Cylinder height: 870mm total height: 2040mm total width: 1460mm height of the feet: 560mm materials: Interior: 1.4301 / AISI304 External parts: 1.4301 / AISI304 Csdjfiguuspfx Aa Nogp facilities: Double Jacket Nameplate: yes Outlet: 70mm Various connections Gratings Agitator

Year of construction: 2025, condition: new, Brand new stainless steel agitator tank with beam agitator and load cells CILC2000RWS Volume: 2107L Dimensions approx.: Ø 1430mm x cyl. Height 1250mm Total height: approx. 1650mm (plus agitator motor) Material: 1.4301 stainless steel V2A Cgedovtyf Ijpfx Aa Njp Surface: inside BA (IIId), outside satin finish Welding seams in the container ground -Standing design on three feet -Top: hinged lid, central crossbar with 2 hinged lid halves with locking function (can be locked in 90° open position) -Metal grates below the hinged lid as protection against soap, screwed, removable -Bottom: conical bottom with central outlet DN50 DIN11851 nozzle -Agitator flange on the top -1x reserve nozzle DN50 DIN11851 on the top with blind cap -Type plate -180° spray head - Weighing cells - Speed control Agitator: Bar agitator Make: Schwarzer Rührtechnik GmbH Type: SRTGMK/1.5-149 Power: 1.5KW Speed: 149RPM Operating voltage: 3PH 400V -Gearbox made by Getriebebau NORD -Solid agitator shaft with sleeve coupling attached to the gear motor, removable -Agitator shaft balanced for concentricity in the speed range -2 2-blade bar agitators Ø 500mm, height adjustable on the agitator shaft, attached via side power screws Grilled and passivated -Stainless steel flange with shaft seal and O-ring seal -MFR converter

Condition: new, Factory new stainless steel tank Item number:10639 Volume: 335 L Type: Hanging Material (wetted): 1.4301 / AISI304 Type: double jacket Codpfxsiaup Nj Aa Nsgp Hinged cover: 180x570 mm Working pressure according to nameplate: ATM Tank dimension: Outer diameter: 750mm cylindrical height: 870mm Total height: 1250mm Total width: 830mm Total length: 920mm Materials: Inside: 1.4301 / AISI3304 Outside: 1.4301 / AISI 304 Facilities: Nameplate: No Outlet diameter: 1. DN40mm / 2. 45mm Various connections Gratings

Condition: like new (used), Equipment: type plate available, Used stainless steel transport container Prepared for agitator Type: SBPA150 Item number: 10796 Volume: 173 liters Cgjdpfx Aaer A Enge Nsp Type: Upright design on pallet Design: Single-walled, 1.5mm wall thickness Material (wetted parts): 1.4301 stainless steel Surface: Satin-finished outside, IIId inside Internal weld seams: Pickled, passivated and brushed Operating pressure: Atmospheric Top: 1/2 hinged lid Underbody: dished bottom with outlet bead Tank dimensions: Tank diameter: 650mm Total height: 815mm Pallet: 675 x 719mm Equipment: 1x 1/2 hinged lid on the top, latching function (lid can be latched in open 90° position) Stainless steel sheet metal grates underneath the hinged lid, screwed, removable DN50 ball valve outlet fitting DIN11851 Galvanized transport pallet Type plate

Condition: like new (used), Equipment: type plate available, Used stainless steel agitator tank on stainless steel pallet with rollers and propeller agitator Type: SBPA1000RWP Article number: 10862 Volume: 907L Type: Upright design on stainless steel transport pallet with rollers Design: Single-walled, at least 2mm wall thickness Material (in contact with media): 1.4301 stainless steel Surface: Satin finish on the outside, BA (IIId) on the inside Inside weld seams: Pickled, passivated and brushed Operating pressure: Atmospheric Top: Central crossbeam with two hinged lid halves Bottom: Dished bottom with discharge bead Container dimensions: Container diameter: 1080mm Total height: 1915mm Total width: 1200 x 1150mm Distance from drain to floor: 400mm Height of feet: 240mm Equipment: 1x hinged lid, central crossbar with two hinged lid halves, stainless steel sheet metal grates below the hinged lid as protection against intrusion (removable), locking function (lids can be locked open) 1x reserve nozzle DN50 DIN11851 on the top floor 1x DN50 DIN32676-A Tri-Clamp ball valve as outlet fitting, PTFE seal 1x stainless steel transport pallet 4x swivel castors, 2x with brake 1x nameplate Agitator: Propeller agitator Suitable for viscosities up to 500mPas Make: Schwarzer Rührtechnik GmbH Type: SRT8-1500 Power: 0.75KW Speed: 1410 UPM Operating voltage: 3PH 400V -Solid agitator shaft attached to the agitator motor, not removable -Agitator shaft balanced for concentricity in Speed range -1 mixing propeller Ø 150mm screwed into the end of the agitator shaft. Mixing propeller made of cast stainless steel, highly polished -4x neoprene rubber metal buffers, motor mounted in a swinging manner, hardness grade 70 according to Shore, neoprene resistant up to 100°C Agitator control: Csdpfxev Ha Uie Aa Nsgp CEE plug switch on the container, on/off switch, emergency stop, zero voltage release and phase inverter Continuous speed control of the agitator motor using a compact, external frequency converter, Optidrive brand. With digital display of the frequency or speed. Incl. potentiometer, on/off switch. Pre-programmed for agitator operation. Operating voltage 3PH 400V Mounted on the container on a stainless steel holder.

Year of construction: 2026, condition: new, IWR 2000D - The fruit washer with mill for fruits and vegetables is made entirely of high-quality stainless steel and is equipped with a sorting grate, a washing tank, and a conveyor belt. The fruits are immersed in water and, after pre-washing, transported via the conveyor belt where they are thoroughly cleaned with fresh water. Afterwards, the cleaned fruits enter the mill, where they are processed to the desired mash consistency using the selected sieve. The washing system is also equipped with a dosing attachment for pack presses. Technical Information Cgodjtu Ikcjpfx Aa Nep • Nominal capacity: 1500 kg/h • Power requirement: 3 kW, 400 V, 16 A • Material: WNr. 1.4301, AISI 304 stainless steel • Washing tank water capacity: 120 L per batch • Water consumption: 12 L/min • Water connection: 3/4” quick coupling • Electric control cabinet with IP65 protection rating • Swiveling Rätz mill • Equipped with rollable wheels • Easy to clean • Through the frequency converter, the conveyor capacity can be easily adjusted Dimensions: Length: 3250 mm Width: 840 mm Height: 2270 mm Weight: 160 kg

Condition: new, Year of construction: 2026, The fruit washer for fruits and vegetables is made entirely of high-quality stainless steel and is equipped with a sorting grate, a washing tank, and a conveyor belt. Initially, the fruits are immersed in water for thorough pre-cleaning. Afterwards, they are transported further via the conveyor belt and carefully cleaned with fresh water. Cgedpfsv Srp Ajx Aa Njp Technical Information • Capacity: 1000 kg/h • Power requirement: 0.75 kW, 230 V, 6 A • Material: WNr. 1.4301, AISI 304 stainless steel • Water connection: 3/4” quick coupling • Electric control cabinet with IP65 protection rating • High-quality workmanship • Equipped with rollable wheels • Low maintenance requirements Dimensions: Length: 2915 mm Width: 840 mm Height: 2270 mm