Used International 1486 for sale (9,611)

Condition: used, Year of construction: 2016, functionality: fully functional, BAC VXC S455 evaporative condenser, 2015, R134a, s/n H150832701 — chiller heat rejection. Used 6 units Baltimore Aircoil International (BAC) VXC S455 evaporative condenser, built 2015, serial number H150832701. Made in Heist-op-den-Berg, Belgium. It is an evaporative condenser: hot refrigerant vapour enters the coils inside the unit, water is sprayed over the coil surface, and centrifugal fans draw air through the pack. The refrigerant condenses and returns to the refrigeration plant. No separate water-cooled condenser is required on the chiller. The unit has twin R134a heat-exchanger coils (circuits A and B) and a centrifugal fan section. It was installed on a rooftop as the heat-rejection side of a refrigeration / chilled-water plant. Manufacturer: Baltimore Aircoil International nv Model: VXC S455 Serial number: H150832701 Year of manufacture: 2015 Type: induced-draft evaporative condenser Vessel type code: PED C100 Refrigerant: R134a Coil volume: 932 L per coil (A and B) Design pressure: −1 / 23 bar Test pressure: 34 bar Design temperature: −20 / +120 °C Fan overall efficiency (nameplate): 59.05% Marking: CE BAC catalogue figures for VXC S455 Base heat rejection: approx. 1,961 kW Operating weight: approx. 11,270 kg Shipping weight: approx. 8,125 kg Nlsdpfx Aaezz Sidozjg Dimensions: approx. 5,385 × 2,397 × 4,248 mm Air flow: approx. 34.9 m³/s Fan motor: 1 × 30 kW Spray water: approx. 38.5 l/s, pump 1 × 4 kW Application Heat rejection for industrial chillers and refrigeration plants on R134a. A natural match for the Star Refrigeration package water chillers (contract 100663, 840 kg R134a charge): discharge gas goes to the BAC coils, liquid returns to the chiller. Condition and sale Used industrial equipment, removed / being removed from site. Price on request. Can be sold with the Star chillers or as a standalone condenser. Model, serial number and pressures are taken from the factory plates; actual capacity at the new site depends on condensing temperature and ambient wet bulb.

Condition: used, functionality: fully functional, total length: 48,000 mm, total height: 6,464 mm, Year of construction: 2019, 2019 FONG KEE THREE-LAYER CO-EXTRUSION FLAT SHEET LINE Up to 2,100 mm net sheet width | 7,000 operating hours Direct owner sale | Can be seen running by appointment Company-owned Fong Kee sheet extrusion line, offered for sale directly by the owner. The line has been used in our own production and remains fully assembled at our facility in Torbalı, İzmir, Türkiye. Originally specified for flat sheet production for furniture applications, the line offers multiple material and layer options. A running demonstration can be arranged in advance for interested buyers. MACHINE OVERVIEW Manufacturer: FONG KEE INTERNATIONAL MACHINERY CO., LTD., Taiwan Model: TSE-90/150/150-2400 Year of manufacture: 2019 Operating hours: 7,000 h Type: Three-layer co-extrusion flat sheet line Layer configurations: A/B/A or A/B/C Processable materials: PET, PMMA, ABS, PS (HIPS / GPPS), PC and PP The material options and layer configurations listed above have been confirmed through our own production experience. PRODUCTION SPECIFICATIONS Net trimmed sheet width: 1,500–2,100 mm Die width: 2,300 mm Specified sheet thickness: PET: 0.3–0.8 mm PMMA/ABS: 0.6–0.8 mm Nodpfx Aaszzdnfszjlg Specified maximum output: Up to 1,000 kg/h, depending on resin and sheet thickness Specified operating speed: 3–10 m/min EXTRUSION AND MELT DELIVERY Three vented extruders: Extruder A: Ø90 mm, L/D 35:1 Extruder B: Ø150 mm, L/D 32:1 Extruder C: Ø150 mm, L/D 32:1 Three hydraulic screen changers Three MAAG melt gear pumps Dynisco melt-pressure instrumentation EDI Ultraflow I three-layer feedblock EDI Ultraflex HRC 100 Fastgap die, 2,300 mm CALENDER AND SURFACE FINISHES Horizontal three-roll mirror-polishing stack Roll diameters: 400 / 600 / 600 mm Roll face width: 2,400 mm Mirror-finished, hard-chrome-plated rolls Multi-zone roll temperature control Additional dedicated matte calender roll included In our own production, we have achieved both high-gloss / mirror optical-grade surfaces and anti-glare / matte finishes on this line. DOWNSTREAM EQUIPMENT Dual-sided protective masking film application unit Haul-off unit Automatic guillotine cutting unit Conveyor unit Automatic vacuum stacking unit Two-drum turret winder with automatic tension control ELECTRICAL AND AUTOMATION Siemens SIMATIC ET 200SP PLC Siemens 19-inch and 12-inch Comfort HMI touchscreens Siemens SINAMICS G120 drives Schneider Electric main electrical switchgear Air-conditioned electrical cabinets INSTALLATION AND CONDITION Location: Torbalı, İzmir, Türkiye Overall line length: Approximately 48 metres Condition: Excellent used condition, fully assembled and preserved indoors Current status: Currently idle; can be demonstrated running by prior arrangement Reason for sale: Production facility reconfiguration Please refer to the technical layout drawing for the detailed equipment arrangement, installation dimensions and utility information. INSPECTION AND COMMERCIAL TERMS The complete line is available for on-site inspection and can be seen running by prior arrangement. Delivery terms: EXW Torbalı, İzmir, Türkiye. Reasonable offers will be considered, taking into account the overall commercial terms of the transaction. Detailed technical specifications, the line layout drawing, photographs and an operating video are available for review.

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: P.0020001424, X-Ray Yxlon international MU231 - fully functional (2003) Fully automatic, 100% x-ray inspection of alloy wheels using YXLON's Y.AI/Rel.9 ADR program reaches a cycle time below 25 seconds per wheel. The automatic defect. Fully functional X-Ray for alu wheels. Possible alu wheels from size 12 to 19. Machine is fully working, perfect condition. Nljdsx Hqnrjpfx Aazsg During 2025 full repas was done - all issues are now sorted (tested). Software is unlocked. New owner can test the machine before purchase (Central Bohemia). Machine label attached. Price: 49.000 EUR excl. VAT (price does not include transport and duties) Invoice will be issued in EUR from Czech company. When you will have any questions, do not hesitate to contact us - e-mail / WhatsApp / call Lead cabin (1) with shuttles (2) for the transport of wheels in/out the cabin Decollators to get single wheels for transportation in the cabin X-ray tube (3), Image Intensifier (4), High-voltage generator, X-ray control unit (5) Industrial PC (6) (with mechanical positions and X-ray parameters for every wheel type) Control cabinet with PLC (7) Wheel manipulator (8) (Rotation and linear movement of wheels) X-ray-manipulator (9) (tilt axis with X-ray tube and Image intensifier) Vision System for wheel type recognition Image-Processing Unit (Host PC with Slave PCs) Output conveyor (10) e.g. with an alterable switch (for accepted wheels / rejects)

Condition: good (used), functionality: fully functional, REF: MM6466 1 x OK International Group SuperSealer continuous band sealer on mobile height adjustable stand. Manufacturer - OK International Group. Model - SB-40 EU. Serial number - 218-2527-23 Speed - variable, up to 21.3 m/m. Nedjzudu Sopfx Aazelg Bag material - Heat sealable materials up to 15 mils or 380 microns. Direction - Right to Left.

Condition: ready for operation (used), Year of construction: 2016, operating hours: 23,500 h, functionality: fully functional, machine/vehicle number: 8107000021B, spindle bore: 32 mm, spindle speed (max.): 8,500 rpm, overall weight: 4,300 kg, controller model: FANUC 32i MB, bar length: 3,200 mm, DMG MORI GILDEMEISTER SPRINT 32/5 – Short/Long Turning Automaton Well-maintained machine, low operating hours, including IEMCA BOSS 338/32 HD bar feeder (up to 3,200 mm bar length), year of manufacture 2016, as well as a conversion kit to a long turning automaton (Swisstype kit) for short and long turning on a single machine. Delivery terms: Free on truck Availability: Immediate - subject to agreement NOTE: The machine must be picked up on a fixed date in mid/late October 2026; we will provide the exact date in advance! Technical data: Control: FANUC 32i MB Operating hours recorded: 25,263 Spindle hours recorded: 22,772 MAIN SPINDLE DATA: Max. turning diameter: 32 mm (guide bushing bore: 38 mm) Nljdpfx Aaez A Tbuozsg Stroke Z1: 100 mm Max. speed: 8,500 RPM Drive power S1: 5.5 kW TAILSTOCK SPINDLE DATA: Max. turning diameter: 32 mm (guide bushing bore: 38 mm) Stroke Z2: 200 mm Max. speed: 8,500 RPM Drive power S1: 2.2 kW AXIS DATA X1: Travel: 70 mm Max. speed: 40 m/min Max. acceleration: 5 m/s² AXIS DATA Y1: Travel: 405 mm Max. speed: 30 m/min Max. acceleration: 5 m/s² AXIS DATA X2: Travel: 300 mm Max. speed: 40 m/min Max. acceleration: 5 m/s² TOOL HOLDER DATA – SLIDE 1: Tool holder diameter: 25 mm Number of fixed tools for external machining: 6 Tool holder size: 16 × 16 mm Number of driven tools: 4 Collet type: ESX20 TOOL HOLDER DATA – SLIDE 2: Number of fixed tools for internal machining: 4 Tool holder diameter: 25 mm Scope of delivery: IEMCA BOSS 338/32 HD bar feeder (up to 3,200 mm bar length), year of manufacture 2016 Chip conveyor Available manuals Accessories as shown in the pictures Dimensions & Weight Footprint (L x W x H): approx. 7500 x 1600 x 2500 mm Weight: approx. 4300 kg Attention: Disc damaged! If you have any questions or would like to arrange a viewing, please do not hesitate to contact us! Additional notes: ► Upon request, we can offer transport to your destination. ► The goods are sold without any warranty. ► Technical data is subject to change.

Year of construction: 2023, condition: like new (used), functionality: fully functional, We offer this as new FoodMAC International Ltd BULLDOG 6000/600 Electric Fryer for frying cut potatoes and similar products, year of construction 2023. Model: FRE 6000/600 Voltage: 400 V Nsdozgt D Hepfx Aazjlg Power: 200 kW Year of manufacture: 2023 Weight: 1980 kg Machine number: 3035 Capacity: 1500 kg/h If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: new, Year of construction: 2021, functionality: fully functional, machine/vehicle number: 2113/21, type of input current: three-phase, input voltage: 400 V, total height: 2,200 mm, total width: 1,500 mm, total length: 2,000 mm, nominal power (apparent): 100 kVA, electrical fuse: 250 A, working range: 40 mm, welding power (max.): 100 kVA, overall weight: 2,500 kg, A new, unused butt-welding machine. Originally acquired for butt-welding 40 mm rebar, it was never put into service because the project was cancelled. The machine is currently fitted with 40 mm round jaws, but custom jaws of any required shape can easily be manufactured for it. In addition to rebar, the machine can be used to fabricate joints for heavy machinery or anchor bolts for reinforcement work. Nodpfoz Ehvlox Aazslg Suitable for the butt welding of all types of steel grades up to 1,500 mm².

Condition: not inspected (used), Year of construction: 2020, functionality: unexamined, machine/vehicle number: 71193, measuring range X-axis: 3,000 mm, total width: 500 mm, total length: 1,000 mm, total height: 1,000 mm, overall weight: 30 kg, positioning accuracy: 0.045 mm, ● Availability: By arrangement ● Internal No.: ZM3 Nlsdpfxez A Tcfe Aazog Technical data: Measuring volume: 3,000 mm Accuracy: 0.045 mm Scope of delivery: ● Includes laptop and software as shown in the images (completeness not guaranteed) ● Includes transport case Dimensions & weights: ● Installation dimensions (L x W x H): approx. 1,000 x 500 x 1,000 mm ● Weight: approx. 30 kg Additional notes: ►Upon request, we can offer transport to the desired location. ►The goods are sold with no warranty of any kind. ►Technical data subject to change. ►The red base frame is not included in the scope of delivery.

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, 16-head rotary filling machine with 2 checkweighers Nlodszlhy Hopfx Aazsg year: 2020

Year of construction: 2019, condition: used, total length: 2,600 mm, total width: 2,800 mm, total height: 1,600 mm, cutting width (max.): 1,800 mm, The FQJ-1800 honeycomb panel cutting machine (year of manufacture 2019) is an efficient, used machine, ideal for precise cutting of panels with widths ranging from 125 mm to 1800 mm and thicknesses of 10–80 mm. Equipped with three blades, it allows for adjustable cutting speeds in the range of 0–50 m/min, enabling the machine to be adapted to individual production needs. The motor has a power of 4 kW (380V, 50Hz), ensuring reliable and high performance even under intensive use. The machine comes from the renowned manufacturer San(qingdao) Machinery Co., which guarantees a robust construction and durability. This is an excellent option for companies looking for professional solutions in the field of honeycomb panel cutting. Njdpfx Aezuxmieazolg

Condition: used, For sale: a robust Dresser International M 10 A rough-terrain forklift from 1983. This powerful machine is equipped with a reliable International 6-cylinder diesel engine and has a recorded operating time of 4741 hours. With an impressive capacity of 10,000 lbs (approximately 4536 kg), this forklift is ideal for heavy-duty tasks on challenging terrain. The forklift features hydraulic fork adjustment and side shift for optimal flexibility and precision. The fork length is 1780 mm. The tire size is 20.5-25, and the machine is equipped with a cabin for comfortable operation. The overall dimensions are L: 9000 mm, W: 2550 mm, H: 3250 mm. Please note: the VIN number cannot be read. Nsdpfx Aoz D Auyeazjlg

Condition: used, functionality: unexamined, machine/vehicle number: Platinium GPC PDP Printer, Used IP Semi Automatic Pad Printing Installation / Pad Printer IP Printing International Semi Automatic Pad Printing Machine "Used for Pad Printing of PIA on son-tubes and shaped products" Manufacturer: IP Printing International Belgium Model: Slider 160 GPC+P 290 GPC Type: Platinium GPC PDP Printer Controller: Siemens Simatic Tough Panel Including pallet with tools and spare parts Nodpjw H Naajfx Aazslg

Condition: repair required (used), Year of construction: 2014, functionality: limited functionality, type of input current: three-phase, input voltage: 380 V, total length: 1,800 mm, total width: 1,500 mm, total height: 2,550 mm, inner diameter: 320 mm, workpiece height (max.): 75 mm, grinding wheel diameter: 720 mm, overall weight: 2,800 kg, input frequency: 50 Hz, Equipment: documentation/manual, 2014 Lapmaster DSG 720 Double Side Fine Grinding Machine Used 2014 Lapmaster DSG 720 Double Side Fine Grinding Machine for Sale – 720mm Grinding Wheels – 6 Carriers – Siemens SIMATIC Touch Control – Coolant Filtration System Manufacturer: Lapmaster International Model: DSG 720 Machine Type: Double Side Fine Grinding Machine Year: 2014 Control: Siemens SIMATIC Touch Control Condition: In storage, Functional but top grinding plate damaged. Machine Description The Lapmaster DSG720 is a precision double-sided fine grinding machine designed to process both parallel faces of components simultaneously. This type of machine is suited to applications requiring close control of flatness, parallelism, thickness and surface finish. This machine is equipped with 720mm outside-diameter grinding wheels, a 6-carrier workholding system, independently controlled upper and lower grinding wheel speeds and a Siemens SIMATIC touchscreen control. Important Condition Note The top grinding plate / upper grinding wheel assembly is damaged and requires replacement. The machine is therefore being offered with this known defect clearly disclosed. Prospective purchasers should allow for the replacement of the top grinding plate before returning the machine to normal production use. Main Specifications Manufacturer: Lapmaster International Model: DSG 720 Year: 2014 Machine Type: Double Side Fine Grinding Machine / Double-Sided Grinding Machine Nljdpoz E A Icsfx Aazeg Grinding System Grinding Wheel Outside Diameter: Approx. 720mm Grinding Wheel Inside Diameter: Approx. 320mm Wheel Size: Ø720 x Ø320mm Number of Workpiece Carriers: 6 Upper Grinding Wheel Speed: 0–130 rpm Lower Grinding Wheel Speed: 0–130 rpm Inner Pin Ring Speed: 0–100 rpm The double-sided grinding arrangement allows both sides of suitable components to be processed simultaneously, helping achieve consistent component thickness and parallelism. Electrical Specifications Operating Voltage: AC 380V, 3 Phase Frequency: 50Hz Installed Power: Approx. 18kW Current: Approx. 50A Pneumatic Requirements Normal Air Supply: Approx. 5–6 kg/cm² / 0.5–0.6MPa Minimum Working Pressure: Approx. 4 kg/cm² / 0.4MPa Siemens SIMATIC Touchscreen Control: The machine is equipped with a Siemens SIMATIC touchscreen operator control. Coolant Filtration System Included: The Lapmaster DSG 720 is supplied with a separate coolant filtration system. Approximate Machine Dimensions Machine Width: Approx. 1,800mm Machine Depth: Approx. 1,500mm Machine Height: Approx. 2,550mm Net Machine Weight: Approx. 2,800kg Key Features 2014 machine Lapmaster International DSG 720 Double-sided fine grinding process Ø720mm outer-diameter grinding wheels Ø320mm grinding wheel inner diameter 6 workpiece carriers Upper wheel speed 0–130 rpm Lower wheel speed 0–130 rpm Inner pin ring speed 0–100 rpm Siemens SIMATIC touchscreen control Separate coolant filtration system Feed Tables Included 18kW installed power 380V, 3-phase, 50Hz Approx. 2,800kg machine weight Precision simultaneous grinding of both component faces Please Note: All specifications, dimensions, capacities and machine details quoted above are approximate and are provided for guidance only. Prospective purchasers should verify all important specifications, machine condition, tooling requirements and operating requirements prior to purchase.

Condition: used, Used approximately 8,100 litre stainless steel vertical storage vessel. Internal approximately 1750mm diameter x approximately 3000mm straight side. Has welded dished top and bottom heads. Mounted on (4) legs. Specifications: Capacity: 8,100 L Jacket [Y/N]: No Internal Pressure [Y/N]: No Mixer/Agitator [Y/N]: No Tank Bottom: Dish Nledpfxozn Nr Ne Aazjg Diameter: 1,750 mm Height: 3,000 mm Vertical/Horizontal: Vertical Legs/Lugs/Skirt: Legs

Condition: used, Year of construction: 2020, GS International 10t Bj 2020 Width Length 12 mtr Njdpfxoznfdus Aazslg Hydraulic adjustable Immediately available If you are interested in our loading bridge, we can arrange transport for you.

Condition: as good as new (ex-display), Year of construction: 2023, operating hours: 20 h, functionality: fully functional, machine/vehicle number: 23A0017, turning diameter over cross slide: 520 mm, spindle speed (max.): 3,000 rpm, travel distance X-axis: 500 mm, travel distance Z-axis: 500 mm, spindle motor power: 11,000 W, rapid traverse X-axis: 18 m/min, rapid traverse Z-axis: 18 m/min, total height: 1,890 mm, total width: 1,620 mm, feed length Y-axis: 2,500 mm, type of input current: three-phase, Equipment: documentation/manual, CNC Lathe, with 45° inclined bed - COGENTECH Nljdpfx Asvwbvpeazsg > Siemens 808D control > Siemens motors > Linear guides > 6'' hydraulic universal with 3 jaws > 6-station electric turret

Condition: new, Year of construction: 2018, functionality: fully functional, power: 25 kW (33.99 HP), New in box specialized food waste shredder. Manufactured in 2018 but has never been used, still in box. Njdpfx Aswq Rapoazelg

Condition: ready for operation (used), Year of construction: 2017, operating hours: 5,263 h, functionality: fully functional, machine/vehicle number: 1704080210, travel distance X-axis: 2,200 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 900 mm, workpiece weight (max.): 3,000 kg, spindle speed (max.): 6,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 2,200 mm Travel range, Y-axis: 900 mm Travel range, Z-axis: 900 mm Spindle speed, max.: 6,000 rpm Spindle mount: SK50 Spindle drive: Geared spindle / ZF gearbox Internal cooling through the spindle available Table load, max.: 3,000 kg Table size: approx. 2,350 × 850 mm T-slots: 5 × 22 mm Number of tool magazine positions: 40 Nljdjzy Ny Depfx Aazog Tool mount: SK50 Machine weight: approx. 23,000 kg Operating hours: approx. 5,263 h EQUIPMENT 3 tool carts with tools

Condition: used, Used Oliver & Batlle approximately 1,400 litre capacity 304 stainless steel vertical reactor. Unit has welded dished top and bottom heads. Approximately 1,300mm diameter x 1,100mm straight side. Internal rated atmospheric design pressure at 50 deg.c. Has external half pipe coil stainless steel jacket rated 5 bar design pressure at 90 deg.c. Unit includes top entry stainless steel 2-tier agitator driven by 30kw motor.gearbox. Unit is mounted on side support lugs. Nsdpfezvylisx Aazelg

Condition: used, Year of construction: 2021, operating hours: 4,000 h, functionality: fully functional, machine/vehicle number: 505 IE 2021, tank capacity: 300 l, usable tank capacity: 300 l, total length: 1,120 mm, total width: 1,120 mm, total height: 1,000 mm, inner diameter: 900 mm, outer diameter: 1,000 mm, overall weight: 400 kg, wall material: stainless steel, wall thickness: 25 mm, wall structure: double-walled, number of chambers: 1, manhole diameter: 500 mm, manhole location: front, reception height: 500 mm, discharge height: 500 mm, operating temperature: 10 °C, operating pressure: 3 bar, pressure (max.): 2.55 bar, power: 38 kW (51.67 HP), input voltage: 400 V, input current: 16 A, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, The core Thissen & Stecher TSRR series is primarily manufactured as an indirectly heated electric vessel. However, Thissen & Stecher designs for energy input from gas. The specific factory physical and structural dimensions for the TSRR 300-liter core chassis provide the official footprint for this unit: 📐 Structural Dimensions (300L Chassis) Internal Diameter: Ø 900 mm Internal Depth/Height: 500 mm External Width: 1,120 mm Nljdpfszzxcwex Aazjg External Depth: 1,250 mm External Height: Approx. 1,000 mm to the lip (excluding top-mounted lid clearance/venting arrays). ⚖️ Weight: Net Weight (Empty): The baseline unit weight ranges between 380 kg and 450 kg, depending on the reinforced frame option and agitator configuration. Operating Weight (Full): Approx. 680 kg to 750 kg when loaded to its full 300L liquid capacity. 🔥 Gas Heating & Utility Requirements. Fitted with a gas burner jacket, the unit utilizes an indirect thermal jacket fluid or a direct-fired bottom array. Thermal Power Output: Typically engineered between 38 kW and 44 kW to manage a rapid heat-up curve for a 300L volume. Gas Connection Port: 3/4 inch or 1 inch standard gas line connection. Electrical Supply (For Agitator): Requires a 3-phase 400V / 50Hz connection to power the bottom-driven heavy-duty scraping agitator. ⚙️ Operational Features: Agitator System: Bottom-driven stable agitator with standard stepless speed regulation from 10 to 60 RPM. Tilt Angle: Built with an integrated 5° oblique slope toward the front outlet valve to guarantee smooth product discharge and improved mixing geometry. Controller: Standard integration of the Aditec MIC 900 microprocessor supporting multi-step cooking programs.

Condition: used, Year of construction: 2026, operating hours: 10 h, functionality: fully functional, machine/vehicle number: 2026-078, working width: 1,600 mm, working height: 100 mm, warranty duration: 6 months, cutting width (max.): 1,600 mm, number of slots in tool magazine: 2, Used machine CNC cutter/plotter Cutting area in X and Y: 1,500 x 1,600 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials. Equipment of the used machine. • 1 cutting bridge and 1 Multifunctional tool head • max. material height 100 mm • Multifunctional tool head to hold 2 interchangeable tools • powerful vacuum blower for fixing the material • Standard equipped with gray conveyor table (Conveyor). Can be extended with other tools (on request): • EOT electric oscillating blade • POT pneumatic oscillating knife • PRT rotating blade Nodpfxowgc I Rj Aazslg • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration • Milling Head + exhaust Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) (Product photo as example) The machine is CE certified.

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, type of input current: three-phase, input voltage: 380 V, working width: 1,800 mm, cutting height (max.): 30 mm, compressed air connection: 10 bar, An exceptional opportunity to acquire a fully integrated, high-performance automated multi-ply CNC cutting solution. Commissioned in August 2023 and kept in excellent condition, this complete VetiGraph / Serkon Makina setup is available for immediate purchase. Full UK delivery, professional decommissioning, transport, and complete onsite re-commissioning are all included to get your facility running quickly and smoothly. Get a complete factory upgrade at a fraction of the cost of new equipment. Package includes: * Serkon MC30 Multi-Ply CNC Cutter: 30mm compressed cutting height, 180cm width, continuous conveyor, drill and vortex knife cooling. * MN1 Fabric Spreader & ML2 Roll Lift: Automatic tension-free laying with a 9m x 2m air-flotation table. * Complete CAD/CAM Suite: Includes VetiGraph Pattern Design, Automated Marker Nesting, and FastJet Twin-Head Plotter. * iDigit Photo Digitiser: Quickly converts physical patterns to vector files. Full Turnkey Package: Includes UK delivery, complete installation, fully setup commissioning, 7 days of total onsite training, and a 6-month warranty. Avoid long manufacturer lead times and substantial capital outlay. This complete system is ready for immediate inspection in Preston and fast deployment to your facility. Delivery & Installation: * For deliveries outside the UK, the machine is supplied on an Ex Works (EXW) basis. The buyer is responsible for arranging and covering the cost of international transport, import duties, taxes and any local delivery charges. * Installation and commissioning can be provided by our engineers at an additional cost. For overseas installations, additional charges will apply to cover engineer travel, accommodation and associated expenses. * Please contact us for a quotation for installation and commissioning to your location. Njdpfoz A D Ryjx Aazjlg

Condition: new, Unused Briggs of Burton approximately 1,200 litre 316/316L stainless steel process vessel. Unit measures approximately 1,200mm diameter x 870mm straight side. Unit has bolted dished top and welded hemispherical bottom head. Internal rated 10 bar/full vacuum design pressure at -20 to 210 deg.c. External 304/304L stainless steel jacketed rated 10 bar/full vacuum design pressure at -20 to 210 deg.c. Unit has top entry 316/316L stainless steel gate type agitator fitted with PTFE wall scrappers, driven by 11kw motor/gearbox. Unit includes bottom entry Silverson model BE600 316/316L stainless steel emulsifier driven by 22kw motor. Unit is mounted on 304/304L stainless steel legs. Specifications: Nledpfx Aeyhd Imeazeg Power: 11 kW

Condition: used, Used Bibby approximately 300 litre capacity 316 stainless steel vertical mixing vessel. Unit has welded dished top and bottom heads. Internal rated 3.48 bar/full vacuum design pressure at 100 deg.c. Unit has top entry off-site stainless steel agitator driven by Lightnin model LS25A air operated drive. Unit is mounted on (4) stainless steel legs. Nledpfeygvl Ujx Aazog Specifications: Capacity: 79.2 gal Vertical/Horizontal: Vertical Legs/Lugs/Skirt: 4

Condition: used, Year of construction: 2015, operating hours: 5,000 h, functionality: fully functional, machine/vehicle number: 210054, tank capacity: 225 l, usable tank capacity: 200 l, total length: 800 mm, total width: 1,600 mm, total height: 1,020 mm, inner diameter: 1,498 mm, overall weight: 315 kg, wall material: stainless steel, wall thickness: 10 mm, wall structure: double-walled, number of chambers: 1, manhole diameter: 50 mm, manhole location: front, reception height: 250 mm, discharge height: 250 mm, operating temperature: 300 °C, operating pressure: 20 bar, input voltage: 230 V, input current: 10 A, input frequency: 50 Hz, type of input current: AC, Equipment: CE marking, The Firex Easybratt 200L Gas Variant (BM1G200I) is a heavy-duty industrial tilting bratt pan engineered for bulk cooking, braising, shallow frying, and boiling. While marketed in the 200-liter chassis tier, its precise volumetric breakdown consists of a 225-liter total geometric capacity with a 170-to-200-liter usable working capacity. The comprehensive breakdown of dimensions, weight, and utilities sourced from the manufacturer's technical specifications includes: 📐 Physical Dimensions & Cooking Vessel Overall Width: 1600 mm Overall Depth: 900 mm Overall Unit Height: 1020 mm (with lid closed) Vessel Internal Width: 1498 mm Vessel Internal Depth: 564 mm Vessel Internal Height: 250 mm Cooking Surface Area: 84 dm² 🏋️ Weight & Construction Details: Net Weight: 315 kg. Pan Base Thickness: 10 mm to 15 mm high-thickness compound steel for balanced heat distribution. Chassis & Tank Material: High-grade AISI 304 stainless steel throughout. Tilting Mechanism: This is a motorized model; the suffix is BM1G200I. Nledpfxoz Ad Ste Aazjg Lid: Double-skinned, counterbalanced lid with spring loading to reduce heat loss and enable hands-free opening. 🔥 Gas & Burner Specifications: Total Gas Power: 40 kW. Burner Type: High-efficiency stainless steel multi-tube gas burners. Gas Connection Size: 1/2" inlet. Thermostatic Control: Micro-adjustable range between 45°C and 300°C Safety Features: Automated pilot valve safety shut-off; when the tank is tilted/lifted, burners drop down to a pilot-only mode and automatically re-ignite when lowered back into place. 🚰 Water & Electrical Supply Requirements Water Connection Size: 1/2" cold water inlet Water Supply Pressure: 50 to 300 kPa Water System: Integrated swivel water fill tap built into the top surface for automated pot filling and seamless cleaning. Electrical Feed: Requires a basic 230V / 1-phase supply solely to power the easy-light electronic ignition and internal control array.