Used Mco for sale (272)

Condition: reconditioned (used), Year of construction: 2006, HT 690 MC PowerMill Multi-axis CNC turning / milling center with automatic tool change, Y-axis and B-axis for complete machining of turned and milled parts; Max. Diameter approx. Over bed 700 mm Max. Turning diameter approx. 520 mm Distance between the spindles approx. 1500 mm Travels X-axis 490 mm Z-axis 1055 mm Dedshlvgiopfx Ab Djcl Y-axis 200 mm (+/- 100 mm) Drive power: Main spindle 54 kW (S6) Counter spindle 25 kW (S6) Speed range: Main spindle 0 - 3200 min-1 Counter spindle 0 - 3200 min-1 Main spindle: A2-8 (ASA 8 ") DIN 55026, Counter spindle: A2-8 (ASA 8 ") DIN 55026, Y-axis: travel range +/- 100mm PowerMill: A motorized milling spindle with 48-fold tool magazine is integrated into the upper slide system for machining inclined surfaces and bores. The swivel range of 210 ° can be steplessly traversed and interpolated. Preloaded roller guides in all linear axes; digital drive system, integrated spindle encoder; State-of-the-art control technology SINUMERIK 840D Contains: • Main spindle with clamping cylinder • Counter spindle (with clamping cylinder) • Milling spindle with Y and B axes • C-axis for main spindle and counter spindle • TRANSMIT software for simple C-axis programming • Kelvin cooling unit for headstocks, storage of main and counter spindle and milling spindle • Sinumerik 840D, electronic handwheel, RS 232 interface • Chip conveyor with an ejection height of 1100mm programmable (type hinge belt) • Coolant device integrated in the chip conveyor, HP pump with 14 bar • Feed rinsing device for both spindles • Control cabinet air conditioner • Programmable clamping pressure on main and counter spindle • Line filter • Hydraulic power pack • Machine light • Foot switch for chuck main and counter spindle • Documentation • Special accessories: • Automatic door • 48-fold tool magazine • Foot switch main and counter spindle

Condition: excellent (used), Year of construction: 2019, Refrigeration dryer OMEGA Capacity 9.5 m3/min year of manufacture 2019 Djdpew Ipabsfx Ab Djcl THE DEHUMIDIFIER IS FULLY FUNCTIONAL.

Condition: used, functionality: fully functional, Brianzola Simcor embossing press Working width 400 mm Two feed speeds: 1.5/3 m/min Dcedpfxezwc Aao Ab Dsl 9 embossing heads Technical documentation

Condition: ready for operation (used), Year of construction: 2019, operating hours: 1,612 h, controller manufacturer: SIEMENS, number of axes: 3, This 3-axis EMCO MILL E350 was manufactured in 2019, featuring advanced Siemens control for precise operations. Ideal for complex milling tasks, this vertical machining center ensures reliable performance. Consider the opportunity to buy this EMCO MILL E350 vertical machining center. Contact us for more information. Dsdpoyfu Uxofx Ab Docl

Condition: used, Emco F3 universal milling machine from a vocational training workshop With axis digital readouts Dodpfx Ajztwgfob Decl Includes accessories as shown in the picture X: 350 mm Y: 300 mm Z: 200 mm Table: 600 x 200 mm Rapid traverse rate X, Y axis: 1200 mm/min Spindle speeds: 80 – 2200 (8) rpm Quill travel: 45 mm #8498 Net price

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, Siemens control system, Dodpfx Abezkk Hye Docl 12-station turret (VDI16), collet chuck, jaw chuck, steady rest, driven tools, accessories

Condition: used, 1. Decoiler Brand : SCHLOEMANN Type : Hydraulic expanding decoiler Function : Coil holding and controlled rotation Expansion control : Hydraulic Frame : Welded steel base with integrated brake Estimated capacity : 8–12 tons Coil bore : Ø 508 mm ----- 🔹 2. Straightener / Pinch Roll Manufacturer : COMEC (Société de Constructions Mécaniques de Creil) Type : Pinch roll and leveler Control : Mechanical Order number : 1305.1268 Recommended lubricants : Shell Macoma, Tellus, Alvania (as per nameplate) Function : Feeds and flattens strip before slitting Secondary role : Synchronized strip puller ----- 🔹 3. Slitter Manufacturer : COMEC Type : Circular blade slitting machine Drive : Mechanical gear train Blade adjustment : Manual Blades installed : ~10 sets (visible) Function : Longitudinal slitting of metal sheets into narrow strips ----- 🔹 4. Shear (End Cropper) Manufacturer : COMEC STAMCO Type : Rotating or inline shear Function : End cropping or final length cut Control panel : Electromechanical (visible on photo) Machine Application Dodow Dd Igspfx Ab Docl Complete line for metal coil slitting, producing narrow strips from master coils, with upstream flattening and final end cutting. Features / Differences – Heavy-duty hydraulic decoiler by SCHLOEMANN – Mechanical straightening section from COMEC – Manual-adjust slitter with circular blades – Outfeed shear for end trimming or final cut-to-length – Older but industrial-grade line, suited for medium gauge materials

Condition: like new (used), Year of construction: 2009, functionality: fully functional, Tool Milling Machine Emco C40 Linear with Digital Display and Path Control – Excellent Condition, Tool Holders, CE-Compliant! Dsdpfx Abjyliffo Dscl Technical Data: >> Year of manufacture: 2009 Machine No.: BA1GX1201 >> Milling table clamping area: 800 x 400 mm Number of T-slots: 8 Slot width: 14 H8 Slot spacing: 50 mm Maximum load: 300 kg >> Infinitely variable spindle speeds: 10–5000 rpm >> Infinitely variable feed rate: 10–2000 mm/min Rapid traverse X-axis: 5000 mm/min >> Travel X/Y/Z: 450/350/400 mm >> Vertical and horizontal spindle – SK40 taper >> Manual drawbar system >> Quill stroke: 80 mm >> Weight: approx. 2000 kg >> Dimensions (approx.): 2.5 x 2 x 2 m >> Main drive motor: 7 kW >> Spindle brake >> Technical documentation, spare parts diagrams, operating manual >> Folding machine enclosure >> Coolant system >> Machine lamp >> Tool trolley with tool holders About the machine: Offered is a tool milling machine Emco C40 Linear with path control. This universal milling machine is in an almost mint condition. It comes from a government facility where it was only used minimally. The control system is very user-friendly. Switching from vertical to horizontal operation is very easy by simply swivelling away the vertical head. The Emco has been mechanically and electrically tested by us. Take the opportunity to view and test the machine under power at our facility.

Condition: good (used), EMCO E-900 CNC vertical machining center Technical details: Travel X/Y/Z: 900mm/500mm/500mm, Table dimensions X/Y: 1000mm/520mm, Max. table load: 800kg, Spindle speed: 10000rpm, Spindle power: 11kW, Tool holder type: SK40, Rapid traverse: 24m/min. Machine dimensions X/Y/Z: approx. 2600mm/2450mm/2950mm, Weight: approx. 4800kg, Control: Siemens Sinumerik 810D Shopmill Accessories/options: - tool holders SK40 - documentations - coolant tank Under power in our warehouse, inspection is available at anytime. Djdjzxc Npepfx Ab Decl Videos are vailable upon request!

Condition: ready for operation (used), * Brand: Saxlund Dcodpfxoywmy Sj Ab Del * Model: worm conveyor * A-A Length: 4500 mm, ∅ 400 mm * Driving: 15 kW gear unit. * On stock: 2 pieces

Condition: new, overall weight: 20,000 kg, color: black, driver cabin: other, gearing type: other, Year of construction: 2022, Vehicle location: Bovenden, hydraulic side locking Body: 20t hooklift system for containers up to 7m, with hydraulic side locking. Dsdpfx Aoytrccsb Decl ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors!

Condition: ready for operation (used), Year of construction: 2008, operating hours: 9,848 h, travel distance X-axis: 750 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 640 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, spindle speed (max.): 12,000 rpm, number of axes: 5, This 5-axis EMCO MC 75-50 was manufactured in 2008. It features an X-axis travel of 750 mm and Y-axis travel of 500 mm, providing versatile machining capabilities. The machine is equipped with a Heidenhain iTNC 530 control and a spindle speed of 12,000 rpm. If you are looking to get high-quality machining capabilities, consider the EMCO MC 75-50 vertical machining centre we have for sale. Contact us for further details. • Axes: 4 (standard) + optional 5th axis • Spindle: Kessler • Operating hours: Control ON 36,839 h; Machine ON 21,370 h; Program run 11,122 h; Spindle ON 9,848 h • Electrical: 400 V, 3 phases, 50 Hz, nominal current 50 A, largest load current 30 A, breaking capacity 16 kA • Protection grade: IP54 • Electrical cabinet weight: 220 kg • Cooling: Coolant system with belt filter (MicroMag filtration unit visible) Additional equipment Dcjdpfjywyq Dsx Ab Del • Chip conveyor • Wired electronic handwheel • Lehmann rotary axis with rocker and counter bearing • Zeroclamp zero-point clamping system • Retrofitted electrical cabinet cooling unit (Rittal) • Nikken rotary table Technical Specification Taper Size SK 40

Condition: good (used), Year of construction: 2005, functionality: fully functional, Cotrol system Fanuc 21iB. Djdpeyk D R Tefx Ab Decl Probe Marposs T36. X ... 1200 mm Y ... 600 mm Z ... 640 mm Table ... 1300x620 mm Max. table loading ... 800 kg Taper in spindle ... ISO 40 Spindle revolutions ... 50 - 8000 rpm Number of tools in tool changer ... 24 ks Machine dimensions ... 2001 x 3641 x 3158 mm Weight ... 7000 kg

Year of construction: 2026, condition: new, functionality: fully functional, New machine with a 24-month warranty. Stainless steel model. Advantages: + Mobile unit, with locking castors + Completely made of stainless steel + For the production and preparation of pastry dough, baking cream, chocolate, fondant, fruit jam, glazes, fillings, as well as for any product requiring uniform heating and mixing + Thermal oil circulates in the double-walled tank, designed for safe and easy use + Triple-walled construction for optimal thermal insulation + With side and bottom scrapers + Electronic thermostat for setting the cooking temperature Djdpfxjivdume Ab Decl + Manual/automatic operation possible + Digital temperature display with timer + The tank can be easily tilted via a handwheel for emptying (optional: with a discharge tap) + Safety switch in case of overheating STANDARD accessories, already included in the price: - Discharge tap for quick and easy emptying - Machine with frequency inverter for stepless stirring speed OPTIONAL accessories, available at an extra cost: - Double mixing tool, for particularly homogeneous mixing + €950.00 net - Higher temperature (instead of 150 °C, up to 180 °C possible) + €1,900.00 net Technical data: - Capacity: 120 liters - Max. temperature: 150 °C (optional up to 180 °C) - Thermal oil volume: 29 liters - Heating power: 15 kW - Motor power: 1.8 kW (variable speed) - Connection values: 400 V - 3Ph - 50 Hz - 63 A-CEE plug - Dimensions: 1120 x 905 x 1820 mm (W x D x H) - Filling height: 1380 mm - Net weight: 232 kg

Condition: new, Year of construction: 2026, CORMAK LUFT 700 VSD+PM Compact Screw Compressor with Dryer – Compact Package for Demanding Applications – ENERGY SAVER Dodsycg Ryjpfx Ab Docl SET INCLUDES: LUFT 700 VSD+PM COMPACT screw compressor with dryer Horizontal compressed air tank – 500 L Key Features of the Energy Saver Series 1. Permanent Magnet (PM) Motor Technology Most compressors in the Energy Saver series use permanent magnet motors. Compared to standard induction motors, they: Achieve efficiency levels of IE4 or even IE5 Maintain high performance even at very low speeds (standard motors lose efficiency outside their nominal range) Are smaller, lighter, and generate less heat 2. Advanced VSD Inverter Control The heart of the Energy Saver line is the frequency inverter (VSD). Adaptation to demand: The compressor does not operate on an "all-or-nothing" principle (load/unload). If your system requires only 30% capacity, the compressor reduces speed, consuming proportionally less energy. Eliminates idle running: Traditional compressors often run for several minutes after the tank is full, consuming about 25–30% of nominal power without producing air. Energy Saver models nearly eliminate this wasteful process. 3. Soft Start Thanks to the inverter, these units start smoothly from 0 Hz. This means no sudden current surges during startup, which: Saves the electrical installation in the facility Allows frequent start/stop cycles without overheating the windings 4. Real Energy Savings In practice, the Energy Saver series can reduce electricity costs by 30% to 50% compared to traditional fixed-speed compressors. Additionally, the system maintains very stable pressure in the network (with accuracy up to 0.1 bar), which is crucial for precision devices such as laser cutters. Longer service life: No sudden pressure and temperature spikes prolong the screw stage life. Technical Specifications Motor power: 5.5 kW / 7.5 HP Voltage: 400V / 50Hz Air delivery at 0–6 bar: avg. 690 L/min Air delivery at 6 bar: 690 L/min Air delivery at 8 bar: 650 L/min Air delivery at 10 bar: 650 L/min Outlet connection (G): 1/2" Dimensions: 1840 × 640 × 1470 mm Weight: 320 kg

Condition: used, functionality: fully functional, SAMCO Unilev150 edge sander with a 4-roller feed system Specifications: • Condition – used, after a comprehensive inspection • Manufacturer – Samco • Model – Unilev 150 • Working height – 150 mm • Sanding belt dimensions – 150 x 2150 mm • Table dimensions – 22 x 144 cm • One adjustable table, angled between 0-30 degrees • Motor power – 3.0 kW • Pneumatic belt tensioning and oscillation • Adjustable shoe for sanding veneer on one side and the "back" 15x75 cm on the other • Attachment, protractor for angled sanding • 4-roller feed system with a drive belt included • Dust extraction port – ø 140 mm • Weight – approx. 450 kg • Overall dimensions – 150 x 75 x 165 cm (L x W x H) Dcedpezd S R Hofx Ab Dsl Additional information: • The machine is in good technical condition and ready for immediate use • The photos show the actual condition of the item for sale • Possibility to switch on and test the device on-site • Free training on machine operation (at our company headquarters) • The price stated in the auction does not include VAT and transport costs Financing and transport: • We arrange transport using our MDD fleet, courier companies, or external carriers • We offer financial support in the form of leasing or a lease loan

Condition: new, Year of construction: 2026, LUFT 700 VSD+PM COMPACT Screw Compressor with Refrigerated Air Dryer The LUFT 700 VSD+PM COMPACT screw compressor with an integrated refrigerated compressed air dryer combines state-of-the-art pneumatic technology with high-quality materials and components. Low operating costs, ease of use, an ergonomic and robust design, and high performance guarantee efficient and trouble-free operation. Are you looking for a professional solution for powering pneumatic tools in a workshop, paint shop or small production line? The CORMAK LUFT 700 VSD+PM COMPACT screw compressor with refrigerated air dryer is an excellent choice. With a 5.5 kW motor and an impressive actual output of up to 690 l/min, it provides a continuous supply of compressed air required for efficient operation of impact wrenches, blow guns and painting tools. It can also be used as a compressor for sandblasting applications. This model has been designed for continuous-duty operation, making it ideal for demanding applications such as tyre service centres, large automotive workshops and manufacturing facilities. Investing in a CORMAK screw compressor means a significant improvement in working comfort – say goodbye to noisy piston compressors and enjoy quieter, more stable operation. The screw compressor is also equipped with an integrated refrigerated compressed air dryer, which provides dry and clean air while protecting the compressed air system against corrosion and damage. The LUFT 700 VSD+PM COMPACT oil-injected screw compressor with refrigerated air dryer features a traditional belt drive, resulting in easier maintenance and lower servicing costs. Belt replacement is simpler and less expensive than repairing a direct-drive system, and a worn belt can be easily replaced with a new one. Extended Component Service Life The belt drive also contributes to longer component life. The absence of a rigid connection between the motor and the compressor's working components reduces mechanical wear and stress, helping to extend the service life of the system. The maximum operating pressure generated by this screw compressor is 10 bar. Full control over the machine's operating parameters is provided by an intuitive MAM electronic control panel, giving the operator access to key machine information and greater flexibility and control over the production process. Key Parameters ✅ Pressure: up to 10 bar ✅ Air output: up to 690 l/min ✅ Motor power: 5.5 kW Technical Specifications Parameter Specification Motor power 5.5 kW / 7.5 HP Voltage 400 V / 50 Hz Output at 0–6 bar Average 690 l/min Output at 6 bar 690 l/min Output at 8 bar 650 l/min Dcedoybvkaspfx Ab Del Output at 10 bar 650 l/min Outlet connection diameter (G) 1/2" Dimensions 1350 × 600 × 850 mm Weight 200 kg

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, turning length: 520 mm, turning diameter over cross slide: 360 mm, turning diameter: 310 mm, spindle speed (min.): 60 rpm, spindle speed (max.): 4,200 rpm, spindle bore: 73 mm, travel distance X-axis: 210 mm, travel distance Z-axis: 610 mm, rapid traverse X-axis: 24 m/min, rapid traverse Z-axis: 24 m/min, total height: 1,880 mm, total length: 2,852 mm, chuck outer diameter: 210 mm, total width: 1,722 mm, collet bore: 73 mm, spindle nose: KK6, overall weight: 4,300 kg, Equipment: documentation/manual, rotational speed infinitely variable, The machine is new and has only been used for demonstrations up to now; it has not yet produced any chips. The machine is set up and operational, and can therefore be inspected. Additional options & accessories: - Preparation for a bar feeder. - Tool measuring arm. - Chip conveyor (available upon delivery, not currently included). - 10 bar high-pressure coolant pump. - Rohm KFD-HE 210/3-KK6 3-jaw chuck. Djdpfx Ajzcplyeb Decl - Approx. 9 VDI-30 tool holders (7 static, 2 powered).

Condition: excellent (used), Year of construction: 2023, Rod loader SL 1200 Year of manufacture: 2023 Dedjzuxwbopfx Ab Dscl

Condition: ready for operation (used), Year of construction: 2008, operating hours: 10,459 h, travel distance X-axis: 1,200 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 500 mm, controller manufacturer: FANUC, controller model: 18i, number of axes: 4, This 4-axis EMCO MC 120-60 vertical machining centre was manufactured in 2008. It features an X-axis travel of 1200 mm, Y-axis travel of 600 mm, and Z-axis travel of 500 mm. The machine is equipped with a Fanuc 18i control unit and a tool magazine with 30 stations. It includes a Lang Eco Compact clamping system. If you are looking to get high-quality machining capabilities, consider the EMCO MC 120-60 machine we have for sale. Contact us for further details. Dcedoyxnmvepfx Ab Del • Quantity: 2 machines (offered together) • 4th axis: Yes, mounted • Tool magazine: 30 stations • Automation: Lang Eco Compact 10 (2011) (fully functional) Additional equipment, not included • Chip conveyor • Band filter • Tool holder package SK40 • 10 vices • Custom-made wooden floor grating for ergonomic loading Technical Specification Taper Size SK 40

Condition: used, Year of construction: 2003, control 840D-PCU 50 V1 3 coolant ja chip conveyor ja kW generator - rated current 110 A connected load 56 kW Dedpfx Aboqn A Rro Decl

Condition: good (used), Year of construction: 2002, functionality: fully functional, spindle bore: 50 mm, turning diameter over bed slide: 340 mm, turning diameter over top slide: 170 mm, center height: 170 mm, turning length: 700 mm, spindle speed (max.): 2,350 rpm, Emcomat 17 S Spindle bore: 50 mm Turning diameter over bed: 340 mm Turning diameter over support: 170 mm Center distance: 700 mm Maximum 2350 rpm. Lathe features longitudinal and cross feeds. Digital two-axis position readout. Equipped with emergency stop and chuck guard. Year of manufacture: 2002 5.3 kW 400 V Dcedpfx Absxp Hudj Dsl

Condition: ready for operation (used), Year of construction: 2016, travel distance X-axis: 200 mm, travel distance Y-axis: 150 mm, travel distance Z-axis: 250 mm, controller manufacturer: EMCO, total height: 1,100 mm, table load: 10 kg, overall weight: 400 kg, spindle speed (max.): 5,000 rpm, spindle motor power: 1,100 W, tool weight: 700 g, product length (max.): 1,135 mm, number of axes: 3, This 3s EMCO Concept Mill 105 was manufactured in 2016. It features a maximum spindle speed of 5000 rpm and a spindle motor power of 1.1 kW, providing efficient machining capabilities. The machine has a table size of 420 × 125 mm and a maximum table load of 10 kg. If you are looking to get high-quality milling capabilities, consider the EMCO Concept Mill 105 vertical machining centre we have for sale. Contact us for further details. • Distance spindle nose to table: 95–245 mm • Table size: 420 × 125 mm • T-slots: 2 × 11 × 90 mm • Max spindle torque: 4.2 Nm • Rapid traverse (X/Y/Z): 5 m/min Dodeyhcfkepfx Ab Decl • Feed rate: 0–5 m/min • Max feed force X/Y: 2000 N • Max feed force Z: 2400 N • Positioning accuracy (X/Y/Z): 0.005 mm • Repeatability: 0.005 mm • Tool stations: 10 • Max tool diameter: 55 mm • Max tool length: 50 mm • Tool change time (T1–T2–T3): 9.7 / 5 / 7.5 s • Connected load: 1.4 kW • Required air pressure: 6 bar

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, The machine is in good condition, has been in use until recently, and is now available for sale due to a new purchase. The machine has been regularly serviced. It is ideally suited for sanding solid wood, both straight and profiled parts. The processing side, with its guides, features an adjustable sanding shoe. The feed mechanism is an ideal addition for finer edge sanding on straight edges. The machine has a compressed-air-operated belt oscillation for optimal sanding results. The machine has a chassis. Various sanding belts are included. Dcodpfxszdvups Ab Dol

Condition: used, Year of construction: 2012, turning diameter 550 mm turning length 1500 mm control Fagor 8055 x-axis 108 mm z-axis 3000 mm Dcjdsy N D Sispfx Ab Djl