Used Minarctig 180 for sale (11,173)

Condition: excellent (used), Vötsch Type: VC 7330/S Water-cooled climate chamber Room volume: 3300 liters Data for temperature tests: Temperature range: -70°C to +180°C Spatial temperature deviation: ± 1 to ± 2 K (corresponds to temperature gradient) (2 to 4) Temperature fluctuation over time in the center of the usable space: ± 0.5 - 1 K Guedpfju Au Ersx Ag Neh Temperature change rate (according to IEC 60068-3-5) Heating: 1.5 K/min Cooling: 1.5 K/min Data for climate tests: Temperature range: +10 to +90°C Humidity range: 10% RH up to 98% RH Temperature fluctuation over time ± 0.2 to -0.5 K Humidity fluctuation over time ± 1% RH to ± 3% RH Dew point range +5°C to +89°C Mechanical load data: of the test chamber floor 150 kg Maximum chamber floor load 250 kg Dimensions of the test chamber: Width 2000 mm x Depth 1150 mm x Height 1510 mm External dimensions: Width 4000 mm x Depth 1450 mm x Height 2100 mm Operating data: Test chamber lighting: Halogen bulb 12 V, 20 W Rated voltage: 3/N/PE AC 400V±10% 50Hz Rated power 15 kW, Rated current 34 A External control via the RS 232 interface is of course possible. Refrigerant: R404A / R23 Weight: 1550 kg For your safety, the following information is provided as a buyer! The following steps are performed on our chambers in advance: 1. Functional testing and replacement of necessary components 2. Refilling with legally compliant refrigerant, if necessary 3. Leak testing with a certificate 4. After successful testing, the chambers are subjected to a documented test run. Condition: Used Scope of delivery: (See image) (Subject to change and errors in the technical data, information is subject to change!) We are happy to answer any further questions you may have over the phone.

Year of construction: 1990, condition: ready for operation (used), Center width: 1000mm, turning diameter over bed/crank/trolley: 360mm/510mm/205mm, spindle bore: 42mm, speed: 2100rpm, machine dimensions X/Y/Z: approx. 1950mm/900mm/1350mm, weight: approx. 750kg. On-site inspection is possible. Guedpfx Agswt Tlmj Nsh

Condition: good (used), Year of construction: 1982, Table width 1.8 m Strokes per min. 30 - 150 Gusdpsvi Iimofx Ag Neh Weight 47.000 KG

Condition: good (used), Upper support, upper slide, dovetail guide, tool slide, cross table, support slide, support carrier -Tool slide: Support slide support carrier with turning tool holder -Clamping height: 40 mm -Dimensions: see photos Guedowcwizepfx Ag Njh -Dimensions: 370/180/H170 mm -Weight: 17.8 kg

Condition: good (used), Year of construction: 2009, CC200 control Clamping force: 180 t Between bars: 520x520 Gjdpsv D D N Eofx Ag Nouh Min/Max mold height: 250-600mm Screw diameter: 45mm Maximum injection: 210g

Condition: excellent (used), Here we offer a climate test chamber. Climate cabinet RS SIMULATORS KS600/70 AIR COOLED Climatic test chamber -70/180°C + humidity Last maintenance and leak test carried out 03/2024 by RS simulators Here we offer a climate test chamber. RS climate test chamber air-cooled Refrigerant: R404/R23 Temperature range -70°C to + 180°C Time deviations +/- 0.5 K with empty test chamber Average heating and cooling time approx. 2 K / min Humidity range 10% to 95 % External dimensions: width 1200 mm depth 1600 mm x height 1995 mm Test chamber dimensions width 840 mm x depth 840 mm x height 840 mm Nominal voltage: 3/N/PE AC, 400 V, 50 Hz Nominal power: 7.5 KVA Nominal current: 15 A Guodpfx Aovu Ui Rog Nsh Fuse, on-site: 16 A slow-blow Side feedthrough Cabinet is air-cooled Refrigerant R-404A/R23 Weight approx. 600 kg Type: KS 600/70

Condition: excellent (used), Vötsch Type: VT³ 4150 Vötsch temperature test chamber Air-cooled Rated voltage: 3/N/PE AC, 400 V ±10 %, 50 Hz Rated power: 11.5 kW Rated current: 22.0 A Rate of change: Cooling approx. 3.5 K/min. Rate of change: Heating approx. 4 K/min. Temperature test Gedpou Nh Rbjfx Ag Njuh Temperature range -40°C to + 180°C Display plan External dimensions: W x D x H approx. 1390 x 2380 x 1995 mm Test chamber dimensions: W x D x H approx. 1100 x 1475 x 950 mm Weight approx. 1020 kg / 1540 liters Refrigerant R 404A The following information is for your safety as a buyer! The following points are carried out on our offered chambers in advance: 1. functional check and replacement of necessary components 2. if necessary, refilling with legally compliant refrigerant 3. leak test with certificate 4. after successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: ready for operation (used), A profile hardening system (inductor) AEG-Elotherm Elomat V/N/180/3 is available. The nominal output is 200kW. The system is fully functional and is offered including various coils. Gusdpfx Aottv Trjg Njh

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, machine/vehicle number: 96123, Connected load 380V 46A planing width 180 mm planing height 120 mm length of table 2300 mm 4x Leitz reversible knife heads with 4 knives each 2x feed speeds electric height adjustment Gedpfeh U Db Ijx Ag Nsuh 4x star-delta switch 2x low pressure holder 1x side pressure holder 2x steel feed shafts 1x rubberized pull-out roller Suction connection 4x120 mm

Condition: used, Starter Bosch -Manufacturer: Bosch starter 12 V, unfortunately without type designation -Voltage: 12V -Teeth: 10 -Magnetic coil: Type -Dimensions: see photos Godpfoit Rmfox Ag Neuh -Total dimensions: 340/180/H115 mm -Weight: 13.8 kg

Year of construction: 2024, condition: new, Beside the press granulator Rotor diameter (mm) 180 Rotor width (mm) 180 Rotor speed (rpm) 150 Drive capacity (kW) 3 Rotor knives (pcs) 18 Stator blades (rows) 2 Screen size (mm) >5 Weight approx. (kg) 140 The slow speed granulators in the GSL range are mainly used in injection and blow molding processes as beside the press machines to grind runners and sprues. The machines can be used for rejected products in the inline recycling process as well. Different hopper and base frame designs make it possible to integrate the machine with most types of injection molding machines and robots. Driven by gear motor or V-belt Unique knife design eliminates adjustment after resharpening. Gedjiy D Szjpfx Ag Nouh Simple tool less access for maintenance and cleaning Customizable hopper and base frame

Condition: used, Year of construction: 2000, Used furnace cabinet for die casting machine Frech type DAW 80 - suitable for multi-chamber furnace MELTEC - type 80/180 with individual controls. Gujdpfx Agshwt Rbe Njh Has been checked for functionality by the manufacturer.

Condition: excellent (used), Espec Type: EGNX28-6CWL Espec climate test chamber water-cooled Climate test chamber N series Temperature range -70 to +180°C Temperature change rate Guedpfxov Duuxe Ag Noh Heating 10 °K/min Cooling 5.5 °K/min Humidity range 10 to 95% RH according to diagram Internal dimensions W x H x D in mm 1000 x 1000 x 800 External dimensions W x H x D in mm 1205 x 1930 x 1960 Usable space volume 800 liters Cooling capacity 3.6 kW at -50 °C Heating system 10 kW Refrigerant R-404A Refrigerant R- 508A Power supply: AC 400 V 3-phase 50/60Hz 38A Weight: approx. 695 kg For your safety as a buyer, the following information! The following points are carried out in advance on the chambers we offer: 1. Functional check and replacement of necessary components 2. If necessary, new filling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data, information is subject to change!) We are happy to answer any further questions you may have over the phone.

Condition: refurbished (used), pull-out unit Roller width 180 mm 2 powered rollers below 2 without drive above Godpfx Aonvf Tbog Nouh

Year of construction: 2017, operating hours: 2,500 h, condition: excellent (used), functionality: fully functional, For sale: 1 gas-fired chamber oven with air circulation and bogie hearth Manufacturer: Nolzen Industrieofenbau GmbH & Co. KG Type: KLWg 220/180/650 YEAR OF MANUFACTURE: 2017 for unsupervised operation for three-phase 400Volt three-phase current for temperatures up to max. 700 degrees C. for natural gas "H", liquid gas Number of burners: 8 Total burner output: 720kW Guedpfx Ajr Hmg Rsg Nsh For further technical data see attached PDF. The stove itself was only in operation for 4 years and has made approx. 100 anneals of 23 hours each during this time.

Condition: used, Hand hydraulic pump, hand pump, hydraulic cylinder, hydraulic hand pump,, high pressure pump, high pressure hand pump, hydraulic hand pump, hydraulic pump -Manufacturer: Enerpac, hydraulic hand pump -Type: unfortunately without type designation Gujdekahi Ujpfx Ag Neh -Pressure range: bar -Housing: aluminum -Number: 1x hand pump available -Price per piece -Dimensions : 700/180//H170 mm -Weight: 8,9 kg/pc.

Year of construction: 2024, condition: new, Slow-speed, side-by-side granulator Rotor diameter (mm) 180 Rotor width (mm) 180 Rotor speed (rpm) 150 Drive (kW) 3 Number of rotor blades 18 Number of stator blades 2 Screen perforation (mm) >5 Approx. weight (kg) 140 The slow-speed side-by-side granulators of the GSL series are primarily used in injection molding and blow molding for the inline reduction of sprues and defective parts. Various hopper and extraction systems allow the machines to be flexibly integrated into existing installations. GSL 180 For the comminution of sprues from injection molding and blow molding Highlights of the GSL series: Low noise thanks to the low rotor speed, angled cut, and soundproof hopper in a multi-layer sandwich design. Powerful and efficient drive thanks to a brand-name gearbox. Easy maintenance, cleaning, and knife replacement. The slow-running, stand-alone granulators of the GSL 180 series feature a closed rotor with a diameter of 180 mm. The machines are available in working widths from 120 mm to 430 mm. Gsdpfx Ageqmik Io Neuh The rotor consists of individual discs directly connected to the spur gear unit via an oversized drive shaft. This enables efficient and low-maintenance power transmission. The material to be crushed can be fed by hand, by conveyor belt, or by robot via a generously dimensioned, soundproof hopper in a sandwich design. The granulator is mounted on a low base frame on casters as standard. The mill is emptied via an extraction tray inserted beneath the screen with a pipe connection for a suction conveyor. Applications The slow-running, stand-alone mills of the GSL 180 series were specifically developed for the size reduction of sprues from injection molding and blow molding. Easy accessibility allows for quick color and material changes. The low rotor speed also allows for the processing of both soft and hard materials, ensuring good material quality with low dust content.

Condition: excellent (used), CTS Type: C-40/350 Ex/l Climate Test Chamber, Water-Cooled ATEX Zone 1 The Ex/l designation indicates that this climate test chamber is suitable for use in hazardous areas classified as Zone 1. This means it is designed for environments where explosive atmospheres may occur. Such equipment is specially constructed and tested to ensure safety in these conditions. Temperature Testing: Temperature range: -40°C to +180°C Temperature deviation: ≤ ±0.3 K over time Temperature change rate according to IEC 60068-3-5: Heating: 3.5 K/min Cooling: 4 K/min Heat compensation: approx. 3500 W at +20°C approx. 2000 W at -20°C Gsdpfxowvr H Ue Ag Neuh Climate Testing: Temperature range: +10°C to +90°C Humidity range: 10% to 95% relative humidity Dew point range: +5°C to 78°C Temperature deviation: ≤ 1.0 K over time Humidity deviation: ≤ ±3.0% r.h. over time The technical data refer to an ambient temperature of +25°C, nominal voltage of 400V, without test specimen, without heat compensation, and without additional equipment. Options may affect performance data. Technical Design: Cooling unit: water-cooled, low-noise, fully hermetic, infinitely variable power adjustment via electronic monitoring and control system, environmentally friendly refrigerant R404A Test chamber: Floor load capacity 150 kg/m² Rack: Stainless steel, support surface 620 x 600 mm Load per rack max. 35 kg Total load with maximum rack configuration 100 kg Control system: 32-bit controller LCD operating panel Digital display of setpoint and actual values Numeric input of setpoints Plain text fault messages RS 232 interface Ethernet interface Free switching channels for user-side test item control Dimensions: Test volume: 350 liters Internal dimensions: Height 750 mm × Width 650 mm × Depth 720 mm External dimensions: Height 1800 mm × Width 850 mm × Depth 1640 mm Operating Data: Electrical connection: 400V +6/-10%, 3/N, 50 Hz Nominal power: 7.15 kW Nominal current: 14.3 A Protection class: IP 54 Sound pressure level

Condition: good (used), Core for crane traverse, adjustable traverse, crane traverse, hall crane, crane hook traverse, load traverse, heavy load traverse, -Heartpiece: for crane traverse, sheet metal upper traverse .: 1031 4140 G-12-02-02 -Dimensions: see photos Godov Hm Szepfx Ag Nouh -Quantity: 2 pieces available -Price: per piece -Transport dimensions: 350/180/H310 mm -Weight: 17.7 kg/piece

Condition: used, 2 column punching tool, separating tool, punching tool, punch, punching die, punching stamp, column frame -Punching tool: 2 columns -Punching dimensions: see photo -Dimensions: 180/75/H1100 mm -Weight: 2.0 kg Gujdpfxju I Hpye Ag Njh

Condition: good (used), Magnetic plate, clamping plate, permanent magnet, magnetic clamping plate, magnetic clamping plate, magnetic holder, magnetic table -Manufacturer: Thyssen, magnetic table with pipe holder -Type: 105 662 -Pipe diameter: 45 mm -Dimensions: 220/180/H260 mm -Weight: 13.3 kg Godpfx Agsv Rxkde Nouh

Condition: used, Bending tool, die, upper knife, upper tool, deer foot tool, deer foot tool for press brake Gujdpfjb A Nlqox Ag Njh -Tool: for press brake -Tool radius: 8.5 mm -Dimensions: 50 x 180 mm -Recording: 15 x 17 mm -Length: 3250 mm -Weight: 140 kg

Condition: used, Clamping angle for workpiece clamping -Dimensions: 180/70/H100 mm -Thickness: 18 mm -T-slots: 12 mm -Surface: milled Gusdpjb E N Ttefx Ag Neh -Weight: 3.5 kg

Condition: used, Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Tube diameter outside: 180 mm -Piston: Ø 115/145 mm Guedpfx Agjb A H Ryo Nsh -Stroke: 620 mm -Weight: 87 kg

Condition: used, Bending tool, die, upper knife, upper tool, deer foot tool, deer foot tool for press brake -Tool: for press brake -Tool radius: 13.5 mm -Dimensions: 50 x 180 mm -Recording: 15 x 17 mm Guodpfxsb A Nlpe Ag Neh -Length: 3250 mm -Weight: 140 kg