Used Recycling for sale (2,211)

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Njdsvf E Avspfx Anfsla Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 22,000 kg, oil tank capacity: 900 l, For sale is a complete baling system consisting of conveyor technology, baling press (partially refurbished and tested) and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical Throughput rate at a Nodpoviwdmjfx Anfela bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Comments: The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: used, Year of construction: 2023, operating hours: 1,100 h, functionality: fully functional, machine/vehicle number: C.009088, total width: 5,536 mm, total length: 5,536 mm, total height: 3,500 mm, Equipment: rotational speed infinitely variable, For any further information regarding this listing please contact Njdpfxey Dtyro Anfola

Condition: new, functionality: fully functional, Year of construction: 2026, RSS 600 series Mono Rotor Shredder new model 2026 18.5kw Screen size in consultation Motor cover, pusherbox guide strips, PLC controlled. Conveyor and/or discharge screw is optional available. suitable for various types of plastic/wood/or other material Delivery in consultation Larger or smaller models also available. Intrested ?, reactions with your name, company name and telephone number. Nsdpeirt H Ajfx Anfsla

Condition: new, Year of construction: 2026, functionality: fully functional, Drain screw system in any length, diameter, etc, tailored to your needs and requirements of course also available separately. Nedpfx Aet Iwt Uonfela reactions or questions ? please with full name, company name and phone number.

Condition: new, Year of construction: 2026, functionality: fully functional, We deliver the machines where you want them, install them if you wish by mutual agreement. Optional: stainless steel drain element, stainless steel storage silo, blower, pipes approx 3 meters. Grinder 800 series 22 kW or 37 kW 3 x 2 blade set configuration. Bwj3E79Mpn 2 x stators screen deck your request With Variablele Frequency controller, Optional Product discharge and storage in various options in combination extra favorably priced Motor power adaptable. Other adjustments can be discussed such as a rotor adjustment, more blades e.g. 5 rows of blades or heavy duty version. Delivery / time in consultation. Nlsdpet Iw Hujfx Anfsa Call or email us for consultation or if you have questions, please respond with your name, company name, and correct phone number. Without these correct details RSS Recycling Shredders and Solutions (Netherlands) cannot respond.

Condition: new, Year of construction: 2026, functionality: fully functional, We deliver machines at any place, install when you whish and support you along the way, at any time. Grinder 1000 series 45kW 3 x 2 knife set 2 x stators screen your request Product discharge and storage in various options. Nledpfx Anog Ainqsfja Other adjustments negotiable. Delivery in consultation. Call or email us for consultation or if you have any questions, important! name company name and telephone number.

Condition: new, Year of construction: 2026, functionality: fully functional, RSS HD 4 Shaft Shredders in any size, Adjustments to e.g. knives, motors, sieve, frame possible. Supply and discharge belts, storage, metal separation possible. Njdpfx Anjh N Dmnefela Larger or smaller models also available. optional fast hydraulical screen cleaning or changesystem for advise or information do not wait, contact us. Delivery in consultation.

Condition: new, functionality: fully functional, Year of construction: 2026, operating hours: 4 h, power: 45 kW (61.18 HP), Rotor length: 1000 mm, motor power: 45 + 2.2 kW. Hopper size: 1400 x 1000 mm, screen size available on request. Optional conveyor belt available. Nlodpfjkzg U Djx Anfea Delivery upon request. For more information: RSS Recycling Shredders & Solutions Please include company name for inquiries or questions. IMPORTANT! Provide name, company, and telephone number.

Year of construction: 2006, condition: refurbished (used), functionality: fully functional, We are offering this refurbished MG Recycling M_04772 cable granulator, year of manufacture 2006. It was fully overhauled in 2024. New control cabinet, new blade sets. Includes Wagner pre-shredder type WS 15, year 2007, 15 kW, feeder belt, extraction system and magnetic vibrating table from 2021. Throughput: approx. 150–180 kg/hour, depending on material. Location: Switzerland, 8260 Stein am Rhein. Asking price: negotiable, EUR 89,000 Nledpfxoy D Ug Tj Anfsa If you have any questions or require further information, feel free to send us a message or call us.

Condition: reconditioned (used), Year of construction: 2018, functionality: fully functional, overall weight: 720 kg, total length: 320 mm, cutting length (max.): 300 mm, Alligator shears JMC 320 Fully overhauled, as new IMMEDIATELY available from stock IUT Beyeler AG, DE-06188 Landsberg. Financing and rental possible. We are looking for used alligator clippers! 12-month warranty The well established 320 Shear is a must for any yard and is now recognised as the industry standard for all shears of this type. One of our most popular shears, the McIntyre 320 Nlsdefxvklopfx Anfea Shear has maintained dominance in a demanding market due to its strength, quality and reliability The 320 is powerful enough to deal with a wide range of cutting and cleaning operations and is able to handle; automotive scrap, whole gear boxes, cylinder heads and blocks, oversized gate valves and of course all the usual non ferrous metal separations. The 320 can also be used to cut ferrous metals. Every shear comes with 1 year guarantee, spare parts can be delivered within 24 hours to whole europe.

Condition: new, Mini Cable Recycling Line with a capacity of 50-80kg/h The set includes: 11kW grinding mill - TORNADO 320 Compact dust removal system Belt conveyor Water separator - GOLD RIVER 300/1250 Technical data of the installation: Installed power - 13kW Power supply - 400V; 50Hz Batch efficiency - 50kg/h (this is a real value, checked on basic materials). Dimensions - 3500x3600x1950mm Weight - 950kg Spare consumables included. This is a set of high-quality devices created for cable recycling. The basis of the entire recycling process is proper fragmentation and separation, TORNADO series grinding mills have been designed so that the input material leaves the chamber in a short time, the enlarged sieve area and balanced rotation of the cutting rotor provide us with uniformly cut material fractions. The use of an innovative water system with pressure control valves in GOLD RIVER series separators allows for very precise separation of materials that are difficult to separate. The introduction of a new separation mat solution in combination with several other technical parameters allows for the separation of a single copper wire with a thickness of 15 microns [µm]. At the same time, maintaining the ideal purity of the plastic. Solid Polish workmanship supported by experience ensures a very long service life. The materials used for production are carefully selected in terms of type and meeting the appropriate strength parameters. We provide full post-warranty service throughout the country, we have every part for the offered devices. Recyclable materials: Aluminum cables of all kinds Car harnesses with adhesive insulation Computer tapes Network and telephone cables Coaxial cables, Christmas tree lights Nledev I Skrepfx Anfsa Copper wires filled with silicone or gels 15-micron winding coils, contaminated with plastic and sticky paper Winding coils filled with silicone coating IMPORTANT!! We provide real performance!

Condition: new, Year of construction: 2024, Gold River SWZ-700 water separators Application description: The GOLD RIVER SWZ series separator has been designed for special tasks, it can cope with the most difficult materials that contain many properties that disturb the separation process in separators commonly available on the market. SWZ water separators separate heavy fractions (non-ferrous metals) from, among others, plastics in the process of recycling secondary raw materials. SWZ separator equipped with a four-section copper water system equipped with radial nozzles with variable linear geometry. The separator uses the latest divided type of separation mat. The development of a modern module for preliminary division and preparation of material guarantees the purity of recovered raw materials in a very short time (plastics, metals). Nledpfx Ajua Tbwonfja Why a water system? Our device uses a system similar to that used in the gold recovery industry. We use water as a carrier and a force that affects the materials in a gentle way. In the water system, all particles with higher mass are gently washed out and separated, generating no losses during the entire separation process. The properties of water together with our proprietary solutions are unrivaled compared to, for example, air separators. SWZ type separators are used: Separation of heavy from light materials (metal granulates contaminated with plastic, foil, paper, cotton, fibers) Cleaning plastics after air separators (dry) Separation of metals in cable and non-ferrous metal recycling lines The SWZ-700 water separator, thanks to the use of the latest module, performs the separation process in a very short time, therefore it is characterized by a high hourly efficiency of separated material of approximately 1200 kg/h. Description of action: The material fed into the separator goes through the transport channel to the module for initial fraction division into its mass and humidity changes. Some of the material is separated at this stage. In the second part of the module, the humidity of the remaining batch changes. Then the material falls onto the separation table where the final fraction separation takes place. As a result of this process, we obtain valuable materials from both sides of the separator. Construction description: The massive structure and the inertial drive of the separator are made of materials appropriately selected to withstand the overloads resulting from vibrations. The supporting frame ensures excellent stiffness and failure-free operation for many years. Due to the type of vibration drive, the design does not require the installation of a soil separator. Separation table equipped with hydraulic adjustment of the angle of inclination. The separation table has a special module for initial division of fractions into their mass and preparation for final separation. The water system has several water pressure valves. The water circulation in the separator is closed. There is no need for constant access to an external water source because the device works using the water already in the tanks. Based on experience and continuous research in our laboratories. We are able to provide you with separators individually adapted to the specific nature of the material being separated. In various versions and sizes. SWZ-700 separators are manufactured to individual order.

Condition: new, Year of construction: 2025, overall weight: 150,000 kg, We offer Lines for shredding and separating non-ferrous metals and copper cables. The line can be freely modified according to the customer's needs. The attached visualization is illustrative. Machines included in the line: Drum Belt Magnetic Separator Multi-shaft shredder 2 x 18.5 kW MCW-110 1. Loading conveyor (controlled automatically by shredder, according to load) Technical data: - L – 4000mm -Working width – 720mm - Height – 2100mm - Geared motor – 1.5kW - PVC conveyor belt equipped with straight cleats. - Steel structure, placed on self-adjusting wheels 2. Unloading conveyor (receives the shredded material for further process) Technical data: -L. – 3600mm Nedpjv I Shdofx Anfjla - Working width - 400mm - H – 2000mm - Geared motor – 1.1kW - PVC conveyor belt equipped with a sealing wave and straight cleats - Structure made of acid-resistant steel, placed on self-casting wheels 3. Magnetic separator – (automatically separates unwanted steel elements from the belt of the unloading conveyor) Technical date: - L – 1400mm - Working width – 380mm - Height – 300mm - Geared motor – 0.55kW - Structure made of acid-resistant steel - PVC conveyor belt equipped with straight cleats - Magnetic plate made of permanent magnets 4. Magnetic plate with quick-cleaning overlay – (separates very small steel elements) Technical date: - W – 490mm - L – 330mm -H- 80mm - Housing made of acid-resistant steel Vibrating feeder PWR-1000 Eddy Current Separator WPS-1000 Discharge conveyor no. 2 of the WPS-1000 separator . Horizontal shredder RKZ-1200 Dust extraction DUST EATER OPW-400 GoldRiver SWZ-700 Water Separator Automatic plastic receiver Automatic metal vibration receiver.

Year of construction: 2022, condition: new, The MDS-1 Electric Motor Recycling Machine designed to accurate copper extraction from stator insert of electric motor with different types of diameter. Description: Nledpfx Aohix N Ajnfja The machine use steel claws to extract copper from the stator shell during backward movement. Stator fixed on special rollers mounted on lifted platform, a holder located in front of the machine keeps the stator from moving. Steel claws release copper when the operator pulls leaver backward. The machine fitted on solid frame, equipped with two sizes of hydraulically operated claws, holder and lifting platform with rollers. Technical information: • Engine power – 11 kW • Maximum engine diameter – 690 mm • Minimum engine diameter – 150 mm • Two types of clamping jaws • Foot switch • Weight – 1250 kg • Dimensions – 2950 × 1150 × 1250 mm • Control panel with an electrical security system

Year of construction: 2024, condition: new, functionality: fully functional, Description of Use: Overband Magnetic Separator (MAGNETIC series) is applied to loose materials to automatic removal of ferrous impurities in the process of waste recycling. Apart from metal recovery the Separator has a protective function for equipment in further steps of recycling process. They are usually installed on top of transport conveyors. Nodpfxoh D H Rcs Anfjla Belt separators are used in many fields: -scrap removal from coal and aggregate -wood and plastic purification -iron particles recovery from cable shredding -iron rejection from WEEE recycling process -municipal waste purification Contact us for more information

Condition: new, Year of construction: 2026, 600 HD available immediately Serialnumber 965 Nlsdpfeib Ircox Anfea Special price from our stock 06188 Landsberg, Germany The 600HD alligator shear is a fast and strong metal cutting shear with an extended hold down clamp, making it ideal for every cutting and cleaning task whether cable, plastic sections or window frames. Its cutting capacity is up to 63mm, 2″ inch mild steel round bar. The 600HD alligator shear is probably best known for dealing with car radiators. It was designed and built following requests from customers who were looking for a shear with a longer blade to cut larger items such as car radiators which it cuts through in one pass. The automatic hold down clamp holds material in place during the cutting cycle and prevents kick back which speeds up processing and improves operator safety. As with all McIntyre shears, opening and closing the jaws is controlled from a moveable foot pedal. As soon as the foot pedal is released, the cutting blades return to the open position. However, a continuous cutting action can be achieved by keeping foot pressure on the pedal. The 600HD can be supplied with an electric motor or with a 2-cylinder diesel engine.

Condition: new, Year of construction: 2025, Alligator shear JMC 500 HD brand new AVAILABLE NOW, ex work IUT Beyeler AG, Nlodohq Nk Ropfx Anfja DE-06188 Landsberg

Year of construction: 2026, condition: new, functionality: fully functional, ERFOR GR7 Granulator – Efficient Plastic Recycling Solution Njdpfx Aney Eyrdsfela We offer the ERFOR GR7 granulator – a robust and efficient machine designed for producing high-quality regranulate from plastic materials. An ideal solution for companies looking to process production waste and reduce raw material costs. Key Information: Throughput: up to 700 kg/h Materials: LDPE, HDPE, PP (films, production waste, printed materials) Stable, continuous operation High and consistent granulate quality Simple and reliable operation Equipment: High-performance plasticizing unit Automatic filtration system Granulation system Compact, industrial design Why GR7: Fast return on investment Reduced material losses Reliable and long service life Configurable to customer needs Condition: New / built to order Manufacturer: ERFOR / Koltex PRS Contact us – we will configure the machine for your material and required capacity.

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Nodpfxjxbgnho Anfela Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, Alligator shear brand new AVAILABLE NOW, ex work IUT Beyeler AG, DE-06188 Landsberg Financing and rental possible. We are looking for used alligator shears! The McIntyre 407 Alligator shear is a non ferrous shear which is both affordable and efficient. It has a 407mm 16″ blade length and enough power and speed to handle a wide variety of cutting tasks. This versatile alligator shear was built originally for scrapyard use so is robust enough to withstand difficult working environments. It is now our most popular shear with thousands in daily use worldwide. The McIntyre 407 non ferrous scrap shear can handle: Automotive scrap Nledshq Nlgspfx Anfea Whole gear boxes Cylinder heads and blocks Oversized gate valves And of course all the usual non ferrous metal cutting tasks. It can also handle ferrous metals if needed.

Condition: new, Year of construction: 2025, JMC 600 GT on stock. Rental and financing possible The 600 GT features a blade guard system which gives good visibility to the operator and acts as a hold down to prevent material kick back. The machine is foot pedal operated and the jaws return to the open position once the foot pedal is released to increase safety. Wheels are fitted as standard, and forklift points have been included on the body of the machine to ensure that it can be safely lifted both within the yard and during transportation. Nedpfxjid Ipco Anfela Ideal for larger items such as car radiators which can be handled in just one pass. The 407/500/600GT can also be adapted to process catalytic converters. JMC catalytic converter shears have been purpose built to recover the valuable dust containing precious metals found in catalytic converters in ELV (end-of-life) vehicles. The shears are sufficiently versatile to be used anywhere in your yard. The catalytic converter is placed in the jaws which are controlled by a foot pedal, and cut open Once cut, the pinched end of the converter can be re-opened using the side bracket attached to the top jaw, allowing the contents to be poured out. All JMC Cat Shears can be supplied with dedicated extraction and filtration systems to remove additional dust because this may also contain precious metals. So you can be sure that you will maximise the return from your catalytic converters. Shears in the range include the 407 Cat which has a 407mm, 16″ blade, the 500 Cat which has a 508mm, 20″ blade and the 600Cat which is equipped with a 608mm, 24″ blade.

Condition: good (used), We offer a range of auxiliary granulators for sale. Further information available upon request. Nedpfxeyl Ucvs Anfola

Year of construction: 2024, condition: new, functionality: fully functional, We are a manufacturer of complete technological lines for washing and granulating plastics. Njdpfx Ansuqu Uhjfela We also offer individual devices such as centrifuges, washers, screw presses, and flotation tanks. A high-performance plastic washing and granulation line, engineered for processing a wide range of materials including PE, PP, HDPE, LDPE, LLDPE, PS, and ABS. This comprehensive recycling solution efficiently manages cleaning, drying, and granulation processes, ensuring the production of high-quality recycled material. Each line is custom-designed to meet the specific requirements of our clients, with throughput capacities ranging from 300 kg/h up to 2,500 kg/h, providing the ideal solution for operations of any size. The system is built for long-term durability and user-friendly operation, making it suitable for both small and large-scale recycling plants. Advanced technologies maximize productivity, reduce energy consumption, and ensure consistent results, delivering a reliable and cost-effective solution to enhance plastic recycling efficiency. Please contact us for inquiries and quotations. Erfor.pl

Year of construction: 2025, condition: new, functionality: fully functional, DYNAMIC WASHER Model ERFOR® DR8 Component machine for recycling washing lines ♻️ ♻️ ♻️ Dynamic washers are machines designed for cleaning moderately contaminated and fragmented plastic waste, such as: PP packaging, PVC, PET bottles, shredded big bag materials like LLDPE, LDPE, HDPE, PP, PVC, PS, household chemical waste, and many others. The washers offered by Koltex PRS are easy to operate and reliable machines, which can be configured into a highly efficient dynamic cascade washing system (tandem – 2 x 30 kW, 2 x 55 kW, or 2 x 75 kW). Multi-point water dosing to the screen washers (cleaning system) and active contamination extraction ensure more effective operation, while dynamic feed movement is enabled by rotating impeller blades. The extended screen section (1400 mm) significantly enhances washing quality, and drainage of excess water is ensured by an acid-resistant steel screen. The use of two screen segments improves the ease of maintenance. Model – DR8 Motor power [kW] – 30 / 55 / 75 kW Film drying capacity [kg/h] – 1000 / 1500 / 2000 kg/h Milling drying capacity [kg/h] – 4500 Our portfolio also includes: - Complete plastic recycling systems - DWFS® washing lines - Granulation and extrusion lines Nledpfx Asuqlmzsnfoa For more information, please visit our website.