Used Roundness Measuring Instrument for sale (11,532)

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Equipment: documentation/manual, type plate available, SUPER PRICE!!! NOW ONLY 6,000 EUR!!! Taylor Hobson Talyrond 265 roundness measuring instrument. Extremely accurate; it can measure the roundness of lenses, optics, pistons, turbine components, tubes, shafts, and also eccentricity, e.g., of cams on a camshaft or journals of a crankshaft. It is certainly of interest to motorsport and tuning companies. The first photo is a "representative image" from a Taylor Hobson catalog, showing its basic structure, except for the computer. A newer, more modern HP computer with a small form factor is included. Max. diameter: 350 mm Max. test piece height: 500 mm (higher is possible, measured in two sections, up to a maximum of 1000 mm) Self-centering of the workpiece: +/- 5 mm Max. weight of the test piece: 40 kg The system has been used very little and has only had two owners. The original owner, from whom I purchased it, was an implant company in Hamburg. It was used there in a "medically clean environment" and is extremely clean. It was never located in a dirty machine hall. The year of manufacture is estimated to be between 2003 and 2005. The Taylor Hobson measuring software is, of course, included and runs on the supplied HP computer (without a password). It is also on the USB stick, perhaps to be installed on another machine at your location. Accessories are included: the original Taylor Hobson desk, computer, monitor, seven (7!) measuring probes, each of which is very expensive to purchase individually. A sample/pattern lens (hemisphere) for calibration is also included! The very detailed operating manual is on the USB stick, and all circuit diagrams and functional diagrams are also included! The system will be shipped on two Euro pallets via a freight forwarder. It is already securely fastened to them. The Talyrond 265 and the desk will be well-protected for transport with bubble wrap, etc., and wrapped with stretch film, and the system itself is secured with "transport safety screws." Shipping will be at the buyer's expense and will be carried out on two Euro pallets. The measuring system should definitely be set up and put into operation by a Taylor Hobson service technician, who can then recalibrate the system on-site. This is now recommended after a few years. Errors can be made during setup and commissioning. For example, some locking screws are installed for transport, and if you forget to remove them, the system can be damaged when it starts up. Pgjdpfx Aezcqy Eebuju A truly well-maintained, very accurate system that will continue to provide excellent service for many years to come!!

Condition: used, Measuring instruments, calipers, and dial indicators are available for sale. These are used but in good to very good condition. Pgedjz Hxxyopfx Abueu * Calipers with measuring ranges up to 300 mm, * Dial indicators up to 250 mm (including models with round, triangular, and pentagonal tips), * Thread flank measuring screws up to 250 mm, * 3-point flank micrometers (6-7 of them with dial gauges).

Condition: used, Instrument Systems Instrument Systems LED Measurement Laboratory CAS140C, LEDGON 100, Integrating Sphere, Keithley 2611 – Complete System! For sale is a complete, professional LED measurement laboratory from Instrument Systems (Konica-Minolta Group). The system is suitable for the precise optical and electrical characterization of LEDs, LED modules, and small luminaires. All devices come from a laboratory environment, manufactured in 2007–2008, and represent high-quality industrial measurement technology. Scope / included components CAS 140C-152 Spectrometer (2008) Integrating Sphere ISP250-110 + ISP250-211 (2008) LEDGON 100 Goniophotometer (2007) CSD315 3-axis Controller + Emergency Stop Control Panel (2007) Podpfjzimaaex Abujgu Keithley 2611 SMU / SourceMeter PC system including software: SpecWin Pro SpecWin Light Goniometer module Original license CDs User manual “LED test sockets” Cables & accessories as shown in the photos Technical features Measurement of total luminous flux (lumens) Spectral analysis (color temperature, CRI, xy, spectrum) Goniophotometric angular measurement Analysis of radiation patterns Electrical control and IV measurements with Keithley 2611 Fully automatic measurement sequences with SpecWin Pro CAS140C: approx. 36×15×30 cm / 7–9 kg Integrating Sphere: approx. 40×40×45 cm / 6–8 kg LEDGON 100: approx. 80×30×28 cm / 12–15 kg CSD315: approx. 42×12×35 cm / 5 kg Keithley SMU: approx. 36×9×28 cm / 5 kg Dimensions / weights (total approx. 40–45 kg) Important note: “The table shown in the photos is not included in the sale.” Condition: used Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by telephone.

Condition: new, Year of construction: 2026, functionality: fully functional, warranty duration: 12 months, input voltage: 230 V, measuring range X-axis: 200 mm, measuring range Y-axis: 85 mm, measuring range Z-axis: 50 mm, total width: 483 mm, total length: 598 mm, total height: 464 mm, overall weight: 64 kg, input current: 5 A, repeat accuracy: 0.005 mm, input frequency: 50 Hz, Equipment: CE marking, USB port, documentation/manual, type plate available, PG1000-400 – Optical system for inspecting the geometry of rotating cutting tools PG1000-400 is a professional optical measuring and inspection system for quickly checking the geometry of cutting tools. It is designed for tool manufacturers, sharpening shops, grinding shops, tool rooms, CNC machining centers, and quality control/metrology departments. Its main application is the inspection of rotating cutting tools after manufacturing, grinding, sharpening, or reconditioning. The system is suitable for HSS and solid carbide tools, especially drills, end mills, step drills, reamers, taps, form tools, micro tools, and custom-made tools. The device can also be used to inspect carbide inserts, selected thread geometries, screws/bolts, and other precision parts, provided that the geometry being inspected is optically accessible to the camera. The system's primary focus is on the inspection of cutting tool geometry. Typical applications: - In-process inspection directly at the grinding machine or in production - Incoming and outgoing inspection of tools - Inspection after sharpening/regrinding - Quality documentation and measurement reports - Repeated inspection of serially produced tools PG1000-400 allows for the inspection of, for example: - Rake angle and clearance angle - Helix angle - Point angle for drills - Radii and corner radii - Diameters and distances - Cutting edge length - Land width, margin width, facets - Web thickness - Tool profile - Runout - Condition and wear of the cutting edge - Comparison of geometry with DXF/DWG drawings The system operates optically and non-contact. This is advantageous when inspecting sharp edges, fine microgeometries, coated tools, and precise edges, where speed, repeatability, and minimizing operator influence are important. The system includes REACTION software, developed specifically for the inspection of cutting tools. The software offers more than 50 measuring functions, edge detection, automatic alignment of measuring points to the edge, saving inspection scenes, comparison with DXF/DWG geometry, PDF reports with PASS/FAIL evaluation, and data export to Excel/CSV. Technical specifications: - Recommended tool diameter: 0.635–75 mm - Tool measuring length: approx. 190–200 mm - Magnification range: 12.5× to 145× - Camera: 5 MP - Monitor: 27" 4K Ultra HD - Measuring range: 85 mm vertically × 200 mm horizontally - Accuracy/repeatability: ±5 µm at maximum magnification - Device dimensions: approx. 598 × 483 × 464 mm - Weight: approx. 64 kg Offered configuration: - PG1000-400 optical cutting tool inspection system - M / F / A encoders - PC with REACTION software - 27" 4K Ultra HD monitor - Flexible LED lighting with diffuser - Curved magnetic diffusion plate - Rotating base block for clamping fixtures - 1000-026-5"-ASS – 5" V-block assembly with insert, top clamp, and stop - Basic remote operator training About the manufacturer: PG1000 is based on the long-term development of systems for inspecting cutting tools. The first generation of PG1000 was introduced in 1993. The system is manufactured in the USA by PG Inspection Technologies LLC, which specializes in this product line. Since 1996, more than 1000 PG1000 systems have been delivered. Condition and delivery: Pgjdpjzdz S Tsfx Abueu - New machine - Year of manufacture: 2026 - Warranty: 12 months - Location: Czech Republic / EU - Delivery, assistance with commissioning, and training according to agreement - CE marking and relevant EU documentation The device i

Condition: used, Optacom VC-10 Universal Measuring System Surface Roughness Tester / Contour Measuring Device Pjdpfx Abeybbd Ssujgu Device is sold without PC and software (hardware only). Resolution in X and Z axes: 0.002 µm Resolution at the probe tip: 0.003 µm VC-10 measuring range horizontal/vertical (X-axis/Z-axis): 225 mm Measuring system: optical, incremental, and non-contact in all axes (X, Z, T) Accuracy: +/- (0.5 + L/100) µm Maximum measuring force: 10 - 150 mN Measuring speed: 0.1 – 2 mm/sec (automatically optimized) Probe tip radius: 0.002 – 1 mm Measurable slopes: 78° upwards; 87° downwards VC-10 dimensions (W x D x H): 950 x 380 x 725 mm VC-10 weight (approx.): 150 kg Description has been adopted as provided. You are welcome to arrange an on-site inspection. Upon request, we can organize affordable shipping for you! You will receive a proper invoice. For international customers, a net invoice can be issued provided a valid VAT ID number is supplied. Subject to prior sale. Visit our shop and check out our other offers as well. The company names and trademarks mentioned are the property of their respective owners and are used only for identification and description of the products. Deviations from technical data and errors in the description of the item may occur and are subject to change.

Year of construction: 2018, condition: excellent (used), Maximum component weight: 75 kg Maximum moment load of the work table: 1250 g/mm Dimensions of work table: 800 x 890 mm Height of working table: 731 mm Measuring height: 500 mm Pjdpsi Dagkefx Abusgu Total height: 1675 mm

Condition: used, Johansson Type: Johansson Cordimatic 7000 Coordinate Measuring Machine The coordinate measuring machine for measuring large workpieces. Pjdszd N Shopfx Abuogu Johansson Cordimatic 7000 measuring machine with Renishaw retrofit (control, rotary/swivel probe & probe changer library) Johansson Cordimatic 7000 measuring machine with Renishaw rotary/swivel head PH10T Measuring range: 28" x 17" x 13.5" Granite table size: 42" x 28" x 8" Equipped with: Computer Metrologic 1 joystick pendant control Metrologic software manuals Joystick and control from RENISHAW SPA2 servo power amplifier UCC2 controller Condition: used Scope of delivery: (See image) (Changes and errors in technical data and information are subject to change!) We would be happy to answer any further questions you may have over the phone.

Condition: used, Tool measuring device Pgjdoddtuyjpfx Abuju Manufacturer: Mitutoyo Type: Quickset R

Condition: used, Mahr Perthen Perthometer S4P roughness measuring instrument 1 x Mahr Perthen Perthometer S4P roughness measuring instrument 1 x Mahr Perthen 6 86 20 63 1 x Mahr Perthen 42 50 01 50, up to 160 mm Ø More roughness measuring instruments in other sizes – new and used – can be found here. Pgedeihfmuopfx Abuju

Condition: used, This listing is for a Magellan Instruments Tandem Pro Gas Analyser. The unit is in full working condition and is ready for immediate release. The Magellan Instruments Tandem Pro Gas Analyzer is a self-contained O2 & CO2 gas analyzer. The PRO system comes with an internal gas pump and programmable display. It includes calibration functions, error reporting and dual 4-20mA outputs. An RS232 output is included for integration into control systems. Benefits: Greater understanding of your cells and processes Physiological state measurement on-line Scale-up and scale-down predictions Batch variation studies: feature analysis Metabolic flux analysis and mass-balance calculations Accurate fed-batch control Batch variation studies: anomaly analysis Metabolic activity based feeding Dedicated, continuous, standard signals for all your reactors On-line information, allows real-time calculation of RQ, CER, OUR, growth rate, KLa, etc. 0-10V and 4-20mA, with RS232 on PRO & Multiplex Integrates to any reactor size (250ml – 100m3) Specifications: Feature CO2 O2 Measurement Principle: Infrared Absorption Electrochemical Range: 0-5%, 0-10%, 0-20% 0-30%, 0-50%, 0-100% Resolution: 0.01% 0.01% Accuracy: ±2% of full scale ±2% of full scale Drift: Pjdpfx Aboxx Aqysuegu

Year of construction: 2014, condition: new, digital length measuring device, manufacturer: Heidenhain, ID 355 533-04 Pgedpfob T Uqisx Abuju Measuring scale, type LF 481 – Signal 1Vss – Measuring length 200mm.

Condition: ready for operation (used), Year of construction: 2009, Mahr MarSurf CD 120 Contour and Roughness Measuring Instrument, Surface Measuring Instrument Measuring range: 120mm Measuring force adjustable from 2 mN to 120 mN Mahr ST 500 measuring stand Year of manufacture: 2009 Accessories: Contour measuring probe: Mahr PCV probe arm 350 Roughness measuring probe (software license for roughness measurement has expired) Mahr calibration standard Mahr cross slide table You are welcome to come and inspect the equipment. We would be happy to arrange cost-effective shipping for you! You will receive a proper invoice. For foreign customers, a net invoice can also be issued, provided a valid VAT identification number is available. Subject to prior sale. Visit our shop and see our other offers. The company names and trademarks mentioned are the property of their respective owners and are used solely for identification and description of the products. Deviations from technical data and errors in the description of the item may occur and are subject to change. Pgodozmtlqopfx Abuju

Condition: used, This listing is for the Hitech Instruments GIR250 Gas Analyser The unit is in full working condition and is ready for immediate use The GIR250 is a bench‑top / transportable analyser designed to measure oxygen (O₂) and carbon dioxide (CO₂) simultaneously in gas samples. It is made by Hitech Instruments (now part of the MTL / Eaton group). Its design emphasizes ease of use, reliability, and low maintenance cost. Other supporting features: The instrument can be programmed with pass/fail criteria for each gas (alarms). It provides analog outputs, typically 4–20 mA, for external logging or control systems. Calibration is designed to be simple (via the front panel keypad) to reduce training burden. The O₂ galvanic cell is user-replaceable (i.e. maintenance can be performed in the field). Mechanical, Electrical & Operational Details The GIR250 is housed in a rugged, transportable case (lab-style) so it can be used as a benchtop or mobile analyser. Sample inlet and outlet connections use 0.25″ (~6 mm) tubing. The sample system should avoid condensation and contaminants; non‑condensing sample environment is required. Operating ambient temperature: –5 to +40 °C (for non‑condensing conditions) Power / interface: standard for bench‑top analysers (the catalogue doesn’t always detail it, but likely mains or DC supply, suitable for lab use) Typical Applications & Suitability Because it can measure both O₂ and CO₂ in a single unit, the GIR250 is used in applications such as: Respiration / breathing gas analysis / Douglas bag analysis (i.e. in physiological or experimental gas mixture measurement) Fermentation / bioprocess monitoring (where O₂ and CO₂ both matter) Gas mixture / inertisation / process gas quality (checking gas purity, calibrating mixtures) Pgsdpfxoxhdqtj Abusu It is not primarily intended for measuring very low trace levels (ppm-level) of O₂ or CO₂ unless its ranges are suitably adapted or specified. The design is more for percent-range analysis

Condition: used, Oxford Instruments   Oxford Instruments X-Strata 960 X-ray Fluorescence Analyzer – for spare parts / defective   Item Description:   For sale is a used X-ray Fluorescence Analyzer, type Oxford Instruments X-Strata 960. Pgodpozdzifsfx Abusu The unit comes from a laboratory decommissioning and is offered exclusively as a source of spare parts or for repair purposes. No functional testing has been performed – therefore, the unit is considered defective for the purposes of this sale.   Technical Data – Oxford Instruments X-Strata 960 (non-binding)   Feature Description Model X-Strata 960 Manufacturer Oxford Instruments Analysis Method X-ray Fluorescence Analysis (XRF) Application Areas Coating thickness measurement, material analysis, precious metal testing Measurement Geometry Top- or bottom-irradiating, depending on configuration Radiation Source X-ray tube (e.g., rhodium anode), 50–100 W power Detector Proportional counter or silicon drift detector (SDD), depending on version Measurement Range Coating thickness approx. 0.005 – 50 µm (material dependent) Spot Size approx. 15 μm – 1 mm (depending on collimator) Z-Axis Motorized, adjustable up to approx. 230 mm measurement height Sample Chamber (W × D × H) approx. 580 × 510 × 230 mm Sample Table Manual or motorized (200 × 200 mm or larger, depending on equipment) Focusing System Optical / laser focus, partially automatic Operating System Integrated industrial PC with Windows-based evaluation software Voltage Supply 220–240 V / 50–60 Hz / approx. 500–800 W Unit Weight approx. 150–200 kg (depending on version)   Condition: used / defective / for spare parts   Scope of Delivery: as shown in the images – without accessories or software   Important Notes:   Sold expressly as a defective unit without any warranty of functionality. The item is offered as a source of spare parts or for hobbyists. No warranty on function, completeness or technical parameters.   Commercial sale with exclusion of any liability for defects, in accordance with § 447 BGB (distance selling contract).   Scope of Delivery:   Oxford Instruments X-Strata 960 All components visible in the images Other parts, accessories or documentation are not included, unless explicitly stated.   Shipping & Pickup:   Pickup possible and preferred in Borken Shipping possible upon agreement.   (Changes and errors in the technical data are subject to change!)   We will be happy to answer any further questions you may have by telephone.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, measuring range X-axis: 4,000 mm, measuring range Y-axis: 3,200 mm, measuring range Z-axis: 2,100 mm, workpiece weight (max.): 4,500 kg, total height: 3,660 mm, type of input current: AC, total length: 4,800 mm, overall weight: 11,000 kg, input voltage: 230 V, table width: 3,200 mm, table height: 725 mm, table length: 4,800 mm, year of last overhaul: 2024, Equipment: documentation/manual, type plate available, Dual-column CMM * Floor-mounted design (measuring plate in one piece, 5000 x 3100 mm) * Measuring plate is decoupled with active vibration isolation Measuring range * X 4,000, Y 2 x 1,600 (3,200), Z 2,100 [mm] * Overlap of columns in Y = 150 [mm] Measuring uncertainty Single column: 20 + L/60, max. 60 [µm] at L = 4,000 mm Dual column: 40 + L/35, max. 80 [µm] at L = 4,000 mm Dynamics 3D traversing speed 433 mm/sec 3D acceleration 768 mm/sec² Probing system (per column) * HEXAGON HH-AS2.5° * Optical laser scanner, type HP-L-10.10 Controller (per column) * DC800 ETH Wireless operating unit * Portable terminal with display Computer (per column) Pgjdpfx Aboz Rpmwjusu * DELL Tower, 24" monitors * According to the software manufacturer's specifications Software (per column) * PCDMIS CAD++ 2026.R1 * Option: Laser sensor HP-L-10.10 * Dual-column function Extensive accessories * Calibration sphere holder - tactile probes - equipped with 3 * Calibration sphere holder - optical laser - equipped with 2 * Variable stylus assortment * 8-position modules in various lengths * SICK light curtain system integrated for automatic operation, all-round Supplier services * Transport, commissioning, calibration, final acceptance Warranty * 12 months, from the date of acceptance Availability * Short-term

Condition: used, Year of construction: 2019, Manufacturer : ACS Instrument Pgjdex R Dfxopfx Abusu Model: 7400S Year : 2019 Type : Leak test bench / automatic and autonomous leak detector Application: Integrity test for flexible containers (flexible packaging, pouches, envelopes, etc.) EM delta P: +- 5000 Pa Pressure test: -55 hPa to 950 hPa Motor power : 0,75 kW The cup is placed in a sealed enclosure. A vacuum is applied in the enclosure, causing the cup to inflate. The inflated cup is clamped between the two horizontal walls of the enclosure and exerts a force on the internal pressure sensor. The force exerted on this sensor is the image of the internal pressure of the cup. The leak test consists of measuring a variation in the force on the internal pressure sensor between the start and end of the stage. A touch screen for controlling and setting the instrument parameters. A USB key for exporting results. Documentation available

Condition: used, Morphologi Type: Morphologi G3SE Image analysis device for determining particle sizes Morphologi G3SE Pjdpfx Ajzdyypobuegu Advanced particle characterization The Morphologi G3 system is an advanced and easy-to-use instrument for characterizing particles by measuring particle size and shape in the size range from 0.5 micrometers to several millimeters. The necessary flexibility for applications in research and development, as well as the reliability for user-independent results and validation mechanisms for automated quality control, are combined in a single instrument. This technology is often used in conjunction with particle size determination using laser diffraction to gain a deeper understanding of product or process behavior. Model: Morphologi G3SE Manufacturer: Malvern Objectives: 2.5x; 5x; 10x; 20x; 50x Condition: used Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by phone.

Condition: used, This listing is for a Hanna Instruments HI 9060 Waterproof Thermistor Thermometer The unit is in full working condition and is ready for immediate release. The Hanna HI 9060 is a high-performance thermistor thermometer specifically engineered for use in challenging wet and humid environments. Its robust design and advanced features make it an essential tool for professionals in the food industry and other applications requiring precise temperature monitoring. Key Features: Waterproof and Rugged Design: Built to withstand harsh conditions, the HI 9060 is waterproof and can endure the rigors of busy environments, ensuring reliability in various settings. Dual-Level LCD Display: The intuitive dual-level LCD display shows the current temperature alongside the highest and lowest temperature extremes recorded during the session, allowing for quick assessments. Temperature Measurement: Measures temperatures in both degrees Celsius and Fahrenheit, providing flexibility for diverse applications. Interchangeable Probes: Compatible with a range of interchangeable probes (sold separately), enabling users to customize the thermometer for specific tasks or environments. Advanced Memory Functions: Equipped with memory capabilities that store high and low temperature readings, facilitating easy tracking and reporting of temperature variations. Long Battery Life: Enjoy an impressive battery life of up to 3000 hours, minimizing the need for frequent replacements and enhancing operational efficiency. Auto-Off Capability: The thermometer features an auto-off function that conserves battery life by shutting down after a period of inactivity. Low Battery Detection: Alerts users when battery levels are low, ensuring that the thermometer is always ready for use. Ideal Applications: Food Services: Essential for monitoring temperatures in kitchens, ensuring food safety and compliance with health regulations. Food Preparation: Pjdpexxz Htjfx Abuogu Perfect for checking temperatures during cooking and baking processes, helping to maintain quality and safety. Packaging: Ideal for verifying temperature conditions during food packaging, ensuring that products meet safety standards. Storage and Transport of Food: Crucial for monitoring storage temperatures in refrigerators and freezers, as well as during transit, to prevent spoilage. Wet and Humid Environments: Designed to thrive in damp settings, making it suitable for various applications beyond food service, such as laboratories or agricultural environments.

Condition: ready for operation (used), Mahr Marsurf XR 1, Marsurf SD 26 roughness measuring instrument, measuring instrument, granite measuring plate Mahr Marsurf XR1 with Marsurf SD 26 feed unit: Measurement of roughness, waviness, and profiles Measuring range: ±250 µm Measuring range with longer stylus arm: up to ±750 µm Vertical resolution: up to 0.7 nm Measuring length: 26 mm Feed speed: 0.1–1.0 mm/s Positioning speed: 5 mm/s Motorized height adjustment: 7.5 mm Measuring force: approx. 0.7 mN Cut-off: 0.08 / 0.25 / 0.8 / 2.5 / 8 mm Individual measuring lengths: 1–50 Pedjz H Uklspfx Abusgu Evaluation: Roughness, waviness, and profile Measured parameters: including Ra, Rq, Rz, Rt, Rp, Rv, RSm, Rsk, Rku, Rk, Rpk, Rvk Software: MarWin Measuring stand: MarSurf ST-D Measuring plate Dimensions: 600mm x 500mm Brand: Bilz Type: F60-50 Max. load capacity: 130 kg You are welcome to visit us for an inspection. We will gladly arrange a cost-effective shipping service for you! You will receive a proper invoice. For foreign customers, a net invoice can also be issued. A valid VAT identification number is required. Subject to prior sale. Visit our shop and browse our other offers as well. The company names and trademarks mentioned are the property of their respective owners and are used only for identification and description of the products. Deviations from technical data as well as errors in the description of the item may occur and are subject to change.

Condition: used, SLA5800 Biotech - MFC - Digitally controlled mass flow controller for gas, Mass Flow Controller elastomer-sealed mass flow controller, flow control, flow meter, flow controller, thermal mass flow BROOKS INSTRUMENT Type SLA585081BAB1A2S1 Ser. No. 01C00500222 Year of manufacture 2020 (new / unused in original packaging) SLA5800 Biotech series Option package Biotech Premium Packet Code T Mains connection 13.5 - 27 VDC (plug M8, 5 pin, male) Power consumption max. 10 watts PROFINET interface (2x RJ-45) Visual display 2 LEDs (NET / MOD) Gas connection 6 mm Swagelok Valve design Normally closed User gas O2 (oxygen) Active - Multiple / O2 (oxygen), N2 (nitrogen), CO2 (carbon dioxide), AIR (air) Calibration gas N2 (nitrogen) Flow control ranges (full scale) 20000 sccm (20 liters / minute) Maximum inlet pressure 4500 psi (300 bar) Normal operation Pressure differential 60 psig (4 bar) Control range 2% to 100% of full scale (range of mechanism) Typical accuracy from 20 to 100 % ± 0.9 % of set point for 20 to 100 % of full scale Typical accuracy from 2 to 20 % ± 0.18 % of full scale for 2 to 20 % of full scale Pgodpfxsuqgbyo Abusu Repeatability ± 0.2 % of the measured value Resolution 0.1 % of full scale Typical response time of the controller

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, type of input current: AC, input voltage: 230 V, overall weight: 723 kg, travel distance X-axis: 235 mm, travel distance Y-axis: 100 mm, travel distance Z-axis: 600 mm, input frequency: 50 Hz, workpiece length (max.): 600 mm, ZOLLER genius 3 threadCheck – CNC measuring and setting device for threading and cutting tools, year of manufacture 2016 The machine is in technically perfect condition and fully functional. THE STRENGTHS – WHAT DISTINGUISHES THE threadCheck FROM THE genius - One machine for all measuring tasks: The threadCheck can do everything the genius can, and with the appropriate adapter holders, it can also perform setting and measuring tasks like a venturion or smartCheck – instead of two or three devices, one is sufficient. - The threading specialist: The 6th CNC axis and the pivoting optics carrier (± 30°) align the optics with the helix angle. Thread drills, milling cutters, and thread forming tools are measured without distortion, contact-free, and with µm precision – the genius cannot do this. - Threading programs without programming: Flank diameter, pitch, flank angle, lead angle, back taper, taper; metric, UNC/UNF, Whitworth, trapezoidal, and round threads. - Grinding wheels and grinding wheel packs are detected and automatically measured via type selection (MP 410). - Fully automatic, operator-independent measurement with test protocol – reproducible, documented, and ensuring reliable handling of complaints. Pods Advh Hepfx Abuogu - Spindle ace: Run-out ≤ 0.002 mm, changeover accuracy 0.001 mm (according to the manufacturer). - Full enclosure protects against dirt and stray light – can be used directly in production instead of in the measuring room. TECHNICAL DATA - 6 CNC axes · Tool length Z max. 600 mm · Tool diameter D max. 310 mm · Y-axis ± 50 mm - Connection 1 kVA, 230 V, 50 Hz · Compressed air 6 bar ± 10 % · Weight approx. 723 kg · gray EQUIPMENT - Software update 2023 to Windows 10 with pilot 4.0 V1.19 - Optics carrier genius 4 1:1/HR70, through-light camera 1:1/HR70, top-light camera HR70 with LED lighting, CNC pivoting device - HG spindle ace size I/AF/HLG with autofocus, hollow encoder for high-resolution C-axis - Operating unit cockpit-pilot with 23" touch display, keyboard, mouse · Control cabinet ventilation - Software threadCheck with photorealistic input dialog and protocol on monitor and printer - Measuring program package inspectionPremium (target/actual comparison, item statistics, cost analysis, TMS “Silver”) - MP 212 flank diameter · MP 370 thread former · MP 851 first full tooth · MP 410 grinding wheels/packs · Macro editor lasso - Collet set Ø 4–16 mm (10 pieces) · Extraction tool · Color laser printer SERVICE AROUND THE MACHINE On request, complete technical support from a single source – according to individual agreement: Software upgrade · Installation and commissioning · Operator training · Support during operation · Demonstration · Warranty according to agreement. PROCESSING Machine in transit, delivery from 16727 Velten near Berlin · FCA Velten including loading · 100% advance payment · Delivery date by arrangement · Inspection by appointment. Data sheet attached as a PDF. Technical data according to manufacturer’s documents and information from the previous owner (information provided, no agreement on characteristics within the meaning of §§ 434, 443 BGB). We will confirm individual values bindingly during the inspection. Errors and prior sale are reserved.

Condition: used, Technical details: x-axis: 1000 mm z-axis: 600 mm diameter: - mm measuring range Y-axis: 972 mm interface: RS-232 tool taper: - weight: 40 kg power consumption: 100 Watt Floor Space WxD: 1,2 x 0,8 m Mitutoyo Linear Height 600 Height Gauge with Wenzel Precision Granite Surface Plate (Optional) The granite surface plate is not included in the sale but can be purchased separately. For sale is a high-quality Mitutoyo Linear Height 600 digital height gauge, designed for accurate 2D measurement tasks in quality control, toolmaking, manufacturing and inspection departments. Mitutoyo Linear Height 600 ·Precision digital height measuring instrument ·Measuring range: 600 mm ·RS232 data output ·Made in Japan ·High accuracy and repeatability ·Ideal for quality assurance and manufacturing environments Measurement Capabilities ·Height measurements ·Internal and external dimensions ·Hole center distances ·Center point determination ·Step measurements ·Diameter measurements ·2D measurement applications ·Angle measurements (with optional accessories) Optional: Wenzel Precision Granite Surface Plate ·Size: 1000 × 630 mm ·Manufacturer: Wenzel Precision ·Inspection date: 07.11.1989 ·Permissible flatness deviation: 0.008 mm ·Measured flatness deviation: 0.005 mm ·Weight: approx. 280 kg An excellent solution for toolrooms, quality control laboratories, precision engineering and manufacturing facilities. Pgsdpfezbqypox Abusu *

Condition: excellent (used), I am offering for sale a professional LeCroy WaveJet 354A digital oscilloscope, designed for laboratory, service, and industrial applications. This is a high-quality measuring instrument with a bandwidth of 500 MHz and a sampling rate of 2 GS/s. Technical specifications: • Manufacturer: LeCroy • Model: WaveJet 354A • Bandwidth: 500 MHz • Sampling rate: 2 GS/s • 4 analog channels • USB port • Built-in carrying handle • Power supply: 90–264 V AC, 47–63 Hz Podpfxjz Snrbe Abusgu Condition: • Used, in good visual condition with normal signs of use. • The device powers on and functions correctly – the display is working, as can be seen in the photos.

Condition: excellent (used), Measuring stand Brand: Fischer Instrumentation (28635) Measuring table 80 x 80 mm Pgjdpfjwn E U Nsx Abusu Installation size 110 mm

Condition: excellent (used), For sale is a robust measuring instrument from the renowned German company AbaWerk Aschaffenburg. It features a cast iron base and is equipped with two hardened centering pins for securing shafts and cylindrical parts. Ideal for use with tool microscopes, measuring projectors, and in quality control. Technical data: • Manufacturer: AbaWerk Aschaffenburg (Made in Germany) • Pin spacing: approx. 115 mm • Stable, heavy cast iron base – secure mounting • Possibility of rotating the part between the pins • Condition: used, fully functional The instrument is manufactured to industrial standards – its precision and durability make such items highly sought after in metrology and toolmaking. Podpfxez Sldpe Abusgu