Cut-to-length line 2.100 x 3 mm/40 t

NN/ BLEMA GOTHA/ HSK

Condition: used, Year of construction: 1977, pressure 250 t stroke 40 - 190 mm no. of strokes 40 /min throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm table height over floor 800 mm ram surface 1200 x 800 mm ram adjustment 125 mm power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m Godpevuuaiofx Abusbh permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation

Condition: excellent (used), Year of construction: 1996, pressure: 13 bar, operating pressure: 13 bar, 1 used steam boiler ----- Make: LOOS, Gunzenhausen Gbsdpfsv I Rpaex Abush Type: U-HD Heating surface approx.: 53 m² Output: 3,200 kg/h Max. operating pressure: 13.00 bar Increased test pressure: 24.05 bar Water capacity at low water level approx.: 2,650 l Water capacity when full approx.: 3,770 l Year of construction: 1996 Equipped with a Weishaupt gas/oil combi burner, gas control system, control cabinet mounted on the boiler body, feedwater pump, and the existing coarse and fine valves.

Condition: used, Year of construction: 1995, operating hours: 1,589 h, machine/vehicle number: 558B, Equipment: all wheel drive, - Wunderschoner Liebherr shovel loader is in a really good condition directly from the military (Swiss-Army) Well maintained and cared for, - The 508 is a really solidly built wheel loader, just right quality for the military. - Is also no source of oil, makes NO oil stains, is almost as good as new - The cab is glazed all around for a good all-round view! ! - The Liebherr L508 is equipped with: Quick change device 0,8m? Bucket, Pallet forks with log push, Additional hydraulic connections for additional equipment, All-wheel drive, Articulated steering 40 degrees very maneuverable with a small turning circle - Tire size 12.5 R 20 off-road profile, tires are foamed (you can not drive flat) Snow chains are also included, Hydro drive, Highest speed 25 Km / H, Displacement 2732 cm? 4 cylinder series Deutz BF4L1011 T with Turb,24Volt power supply, - TUV can be made NEW on request for an extra charge !!! - All my vehicles can be seen on my homepage. - You are now rushing back and forth from Flensburg to Berchtesgaden to look at the different cars, but here you will find over 150 vehicles of the following types: - Hanomag AL 28, Magirus Deutz, MAN, Steyr, Dodge WC, Saurer, Unimog, GMC 6x6, Steyr-Puch, Iltis, Willys, G-Model, Mowag, DB, etc., and all with TUV. - even with TUV. - There are also an unimaginable number of spare parts and accessories. - Why would you settle for anything less? - Call 0049 (0)2248 Greetings, your Philipp from the Hanfbach valley Gbsdeqx S Alepfx Abujh

Condition: used, Year of construction: 2008, Offset 2 color with coating KBA Rapida 105-2+LV CX Year: 2008 Number of impressions (mio): 48 Machine control - ColorTronic - ErgoTronic Professional - LogoTronic Basic - CX Package Feeder Godpfjx Exg Tox Abujbh - DriveTronic feeder - Non-Stop feeder Printing units - Number of printing unit(s): 2 - Straight machine - PWHA Semi Automatic Plate Change - Varidamp dampening - Automatic inking roller washing device - Automatic blanket washing device - Dampening cooling and circulation system: Technotrans - Ink temperature control Coating - Number of coating unit(s): 1 - Harris & Bruno chambered ductor blade system - Number of Anilox roller(s): 1 Drying - IR + hot-air dryer in delivery Delivery - Extended delivery - Powder spray: Grafix Accessories - Compressed air compressor

Condition: like new (used), Year of construction: 1991, functionality: fully functional, table width: 760 mm, table length: 2,700 mm, overall weight: 35,000 kg, pressing force: 250 t, type of input current: three-phase, power: 30 kW (40.79 HP), punching force: 250 t, input voltage: 200 V, Equipment: documentation/manual, safety light barrier, AIDA NC2-250(1) 250t eccentric press in excellent condition /ctA2/ Gbedpfx Asu Dxb Tobueh Manufacturer: AIDA Type: NC2-250(1) Push force: 160t Year of manufacture: approx. 1991 Stroke length: 170mm Distance above table: (adjustable) 280-400mm Table size: 2700x760mm Bear size: 2100x700mm Electrical power: 3x200V(!!), 30kW - Japanese standard Net weight: 35000kg Size: 2760x2800x3980mm Automatic greasing system. Automatic cutting oil dosing - RAZIOL EST-02 Optionally with disc winder and straightener.

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Gbodpfx Abjkvnumsush Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), functionality: fully functional, Year of construction: 1991, sheet thickness steel (max.): 16 mm, cutting length (max.): 6,000 mm, HYDRAULIC SHEAR LVD MVSB 62/16 Serial number 18478 Yom 06/1991 TECHNICAL SPECIFICATIONS Max. sheet thickness St45 16 mm Cutting length 6200mm Distance between uprights 6400mm Gap 60mm Range back gauge 1000mm Min. cutting angle 0.5 ° Max. cutting angle 2.5° Min. number of strokes/min. 6 Max. number of strokes/min 25 Min. blade clearance 0.05 mm Max. blade clearance 1.6mm Motor power 30kW Approx weight 35000 Kg LxWxH 7100x2400x3000mm Gbodpfx Aboumhm Aeush Accessories included; ELGO P85 “GO-TO” for back gauge Electrical adjustment of back gauge 1000mm 1 x Front support 2mtr, one with 90° square arm front support L2000mm Foot pedal Ball bearings on table Inclinable back gauge with manual hydraulic pump

Condition: new, original Siegmund welding table perforated plate octagonal 2D or 3D 1200 x 200 with 28 mm hole 514 kg, diameter 1300 mm plasma nitrided original price 8900.-€ in combination with positioner half price sold only in combination with positioner Hole holder 8 hole 500 x 500 diameter 18mm (see picture) Gjdpfxot Sk Nde Abuobh

Condition: used, Hydraulic Guillotine Shear STEINER Type HTS 30/20 R Machine No. 315 Year of manufacture: 1982 Gbedjd Hxx Aopfx Abuoh Cutting length: 3050 mm Cutting thickness: 20 mm Backgauge: 800 mm, motorized Motor power: approx. 30 kW Power supply: 400 Volts, 50 Hz - Backgauge with ELGO positioning control - Backgauge adjustment via ball screws - SICK safety light curtain at the front as reach-in protection - 3 material support arms with ball transfers - Electric foot switch - Spare blade - Oil cooler with air heat exchanger - Very robust machine with extremely solid construction Machine footprint (L x W x H): 4650 x 2610 x 3200 mm Machine weight: 27,000 kg Transport dimensions (base machine) (L x W x H): 4650 x 2610 x 3200 mm Transport dimensions (additional) (L x W x H): 3500 x 2450 x 1400 mm Total weight: 27,000 kg Good condition Machine can be inspected at our warehouse in 37235 Hessisch Lichtenau, test cuts possible. Currently, the hold-down devices are being resealed; the resulting price adjustment will be made in the coming days.

Condition: used, SLITTING LINE GEORG 1500x1.5x25 Main technical data Coil thickness: 0.24 – 1.5 mm Uncoiler coil weight: 25 Tn Coil width: 230 - 1500 mm Coil outer diameter: Max. 1850 mm Working speed: 200 m/min Slitting tolerance: +/- 0.125 mm Line direction: Right to left Recoiler coil weight: Max. 16 Tn 2 Slitting heads PLC: Siemens S7 1200 Cutting capacity: number of cuts with 350 MPa 24 cuts for thickness 0.25 mm 28 cuts for thickness 0.50 mm 21 cuts for thickness 0.75 mm 18 cuts for thickness 1.00 mm 15 cuts for thickness 1.25 mm 12 cuts for thickness 1.50 mm Scope of supply 1. Coil Carriage 2. Uncoiler 3. Guiding system with 2 measured edges 4. 203.2 diam. Pinch roll before shear 5. Double interlock table 6. Slitting shear:Shaft diameter: 160 mm Gsdoxl R A Ropfx Abuebh 7. 1 off line quick change slitting head available 8. Scrap press and conveyor 9. Intermediate coil table 10. Loop Pit and covering tables 11. Strips Braking Unit 12. Motorised recoiler with hold down separator arm 13. Unloading Coil Car 14. 4 arms turnstile 15. Electrical cabinets & Control panels 16. Existing tooling 17. Existing documentation Coil thickness: 0.24 – 1.5 mm Uncoiler coil weight: 25 Tn Coil width: 230 - 1500 mm Coil outer diameter: Max. 1800 mm Working speed: 200 m/min Slitting tolerance: +/- 0.125 mm Line direction: Right to left Recoiler coil weight: Max. 16 Tn Slitting heads: 2 PLC: Siemens S7 1200 For thickness 0.25 mm: 24 cuts with 350 MPa For thickness 0.50 mm: 28 cuts with 350 MPa For thickness 0.75 mm: 21 cuts with 350 MPa For thickness 1.00 mm: 18 cuts with 350 MPa For thickness 1.25 mm: 15 cuts with 350 MPa For thickness 1.50 mm: 12 cuts with 350 MPa