Aluminum Pvc undercut cutting machine

PLASTMAK PVC AND ALUMINIUM MACHINES SÇ 401

Condition: new, Year of construction: 2026, The CORMAK HBS275 band saw for cutting tubes, profiles and bars is widely used in all locksmith and metalworking workshops where precision, quality and cutting speed matter. The model is equipped with a 0-60° swivel arm; the saw guides are based on sintered carbide. The frame construction ensures accurate and quiet operation. Machine characteristics The horizontal metal band saw with swivel arm enables cutting in a plane perpendicular to the axis of the material being cut and at any angle within the range from 0 to 60°. The material to be cut can be fed manually or by any mechanical device, while the tool feed is automatic. The blade guides are equipped with special carbide plates and bearings. This has a major impact on blade guidance, service life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and blade. The machine is equipped with an efficient coolant pump with a closed coolant circuit. Rsdpfx Ajudi Unsbusch The saw arm is made of a single cast-iron casting and, together with the 27 mm wide cutting blade used in this saw, fully enables multi-series cutting of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The blade guides are equipped with hard metal plates – sintered carbide and a rolling bearing system. It is precisely the SINTERED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The arm has been inclined at an angle of 25°, which increases blade durability and improves cutting conditions. A cleaning brush is mounted at the bottom of the arm to achieve excellent cleanliness and blade operation. The machine drive is transmitted via a worm gearbox. The machine has a three-phase motor with two cutting speeds and motor thermal protection. The shape of the upper part of the base forms a tray for draining coolant and collecting chips generated during material cutting. A cast-iron work table with a swivel arm and a control panel on a separate arm is mounted to the base. In the cutting process, the main cutting movement is the movement of the cutting blade, while the feed is the lowering of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic cylinder. The feed speed is adjusted on the saw control panel. Two cutting blade speeds are available: 37.5 and 75m/min. In the lower position of the arm (after cutting the material), the cutting blade drive is switched off automatically. Safety is ensured by cutting blade guards and micro-switches that stop the motor after the cutting cycle is completed or when any guard is opened; additional protection consists of automatic shutdown of the saw in the event of cutting blade breakage. The machine drive is transmitted by a motor with a worm gearbox. The motor with thermal fuse protects against overheating during operation. Technical data TOTAL POWER 1.5kW POWER SUPPLY 400V 50Hz ARM LOWERING ADJUSTMENT hydraulic cylinder BLADE LENGTH 2450 x 27 x 0.9 mm BLADE SPEED 37.5 / 75m/min VICE BASE HEIGHT 900 mm MACHINE DIMENSIONS (WITH ARM RAISED) (L x W x H) 1720 x 800 x 1800 mm WEIGHT 215 kg

Condition: ready for operation (used), Year of construction: 1992, - Double mitre circular saw ADS type M - 2 saw heads - max. saw length 5000mm Redpeucuhdjfx Abujch

Condition: used, Swiveling aggregate, chain width 10 mm Rcjdpfovvku Eox Abuoh Storage location: Nattheim

Year of construction: 2024, condition: new, Trolley for handling and storing oversize sashes/frames COMALL CARR 900-93/15 Q, new Technical features: - Contact surfaces coated with non-scratch and shock-proof plastic material - Max. height sashes/frames 2500 mm Rsdjm H Twgjpfx Abusch - N° 16 couples of posts - 15 compartments with working size 93 mm - 4 wheels Ø 125 mm, 2 of them with locking device - Load capacity: 850 Kg

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SÇ 441 Portatif Kesim Makinası Ø300 mm, - Used for cutting aluminum & PVC profiles - Double spring system and saw guard safety cut - Cutting on the top table Ability to cut at all desired angles between -45 and +45 degrees Rodpjrcmzdsfx Abuoch - Right and left angle stabilization at 0, 15, 22.5, 30, 45 degrees OPTIONS - Lower cabinet body system - Right-left meter system - Pneumatic press and cooling system - Diamond tipped saw

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SÇ 902 S Hidrolik Alüminyum Köşe Presi Makinesi, • Complies with CE standards • Corner press machine designed for joining aluminium profiles at 90 degrees • 2 upper presses and blade movement are hydraulic • Equipped with a mm scale system for adjusting blade height and feed • Centering square stop is hydraulic • Drain button for fine adjustment is available • Machine comes with 2 pieces of 4 mm blades • 2 pedals are used for hydraulic pressing and profile clamping • Polyamide plate is provided to prevent damage to profile surfaces Rodpfjrbk Tfex Abujch • Left and right profile support arms are available

Condition: used, Year of construction: 2007, machine/vehicle number: 1377, SECOND HAND PNEUMATIC END CUTTING SAW STROMAB MOD. TR500 - CE RULES - with electronic positioning stop TIGERSTOP of 4000mm - infeed roller table of 4500mm - outfeed roller table of 4500mm - blade diameter: 500mm - maximum cutting capacity: 360 mm (L) at 60 mm (H), 135 mm (H) at 280 mm (L) - 10 hp motor - 415 volts - serial number: 1377 Rcedpfx Abet U Izpjush - year 2007

Condition: used, Rip saw - Saw for lengthening boards. - Manufacturer: omega T55 300 Rodpfxotq Eblo Abujch - Year: 1996 - Electric motor - Frequency counter

Condition: new, table length 1590 mm table width 1490 mm table height 840 - 890 mm weight of the machine ca. 0,4 t Rjdpfeh Dqb Dex Abuoch Welding table / perforated table: Hole diameter: 28mm The table is made of 15mm thick, high-alloy steel S355 JR T = 15 The surface is untreated. Sidewalls 165mm height adjustable from approx. 880 - 980mm Ribbed underside for reinforcement. including floor storage Accessories optional !! Surface flatness 0.2 - 0.4mm on 1000mm. The table can be moved with a pallet truck. Pallet truck is not included in the scope of delivery

Condition: new, Year of construction: 2026, PREMIUM VERSION MODELS ARE CHARACTERIZED BY HIGH RIGIDITY AND MAXIMUM RESOLUTION PRECISION, WORKING IN FULL INTERPOLATION IN EACH X, Y, Z AXIS. High-class CNC milling machine designed for the subtractive processing of materials, due to the whole range of configurations, it is used in many industries: industrial, electronics, welding, carpentry, advertising, etc. These are efficient and precise machines equipped with user-friendly CNC control systems. The price quoted is for the machine itself, excluding additional equipment, installation, transport and training. Design Welded steel rigid construction, The gate arms are made of hardened, thick, powder-coated sheet metal, which has increased stiffness, which translates into the quality of the processed detail. Work table The work table is made using hybrid technology, It has T-slots enabling manual clamping of material with dimensions of 2010 x 3010mm, Dissection table with four independent vacuum sections. Drive SERVO motors used to drive high-power machine tools provide appropriate acceleration and speed in individual directions, The X and Y axes are equipped with high-quality toothed bars, praised by users, which ensure high durability and precision, The Z axis is driven by a high quality ball screw. All axles move on rail guides. The machine is equipped with a tool height sensor, Linear bearings: trapezoidal rails, Hiwin carriages. Spindle Rcedpoiz S Hasfx Abuoh The spindle design uses high-quality machine bearings, which are characterized by very quiet operation and guarantee increased durability. Tool height measurement sensor - included. The spindle speed range is from 4,500 to 18,000 rpm. Tool clamping using ER32 collets Software OPTIONALLY The latest UCanCAM V12 software in Polish language version (the software provides the ability to import files from Corel, Autocad, etc. File import/export, text editor and input and many other functions) The software enables quick and easy design of elements, which the program then converts to so-called G-code. It is also possible to import ready files from other programs. The machine is equipped with a function of remembering the last G-code path (In the event of a failure or power outage, it starts working from the last point without losing time or material.) DSP control Digital Signal Processing - digital signal processing. The machine's DSP controller has its own processor and RAM, which ensures failure-free operation and simple operation of the machine. The controller ensures smooth operation of the device and accuracy during processing. There is no need to reinitialize the program after a power loss. The memory built into the controller allows the machine to operate without having to load the program each time. We offer machine tools with real CE EU DTR - certified by the best in the EU. Technical parameters Spindle 5.5kW / 18000rpm inverter, air cooled Work area 2150x3200mm Maximum spindle height 350mm Control DSP Program resolution 0.001mm Software UCanCAM V12 in Polish language version(optional) Power supply 400V Libra 1450 kg Machine dimensions 2680x3600x2200mm Table height 715mm Vacuum pump 7.5 kW (optional) Underpressure 440 mbar Guides linear Drivetrain toothed rack (Z axis - ball screw) Axle drives hybrid servo drives