Bandsaw machine

Rogi CY350RN INVERTER

Condition: excellent (used), Corner jointing machine, Pressta 4000 Pgsdpfsl Skl Djx Aazst Shipping within the EU: approx. €350

Condition: new, cutting diameter 305 mm saw band length 3375 mm cutting width 350 mm dimensions of saw-band 3375 x 27 x 0,9 mm 305 mm 260 mm 350 x 200 mm 250 mm 230 mm 230 x 200 mm 175 mm 155 mm 170 x 100 mm total power requirement 1,5 / 1,8 kW weight of the machine ca. 0,7 t dimensions of the machine ca. 1,5 x 1,8 x 1,9 m Psdpfxsu Dbvto Aazegt

Condition: used, Year of construction: 2025, Cutting height at 90°: 170 mm Cutting length: 430 mm Horizontal miter angle range: 45°-90°-25° Vertical miter angle range: 60° - 90° - 30° Pgodpjiixxnofx Aazet Swivel adjustment with crank: yes Roller conveyor / support table: no Saw blade diameter: 420 mm Speed: 2800 rpm Motor power: 3 kW Motor brake: yes Dust extraction port: 100mm Machine length: Machine width: Weight: 110 kg

Condition: excellent (used), machine/vehicle number: 4220.515, range of control: 20 - 180 A welding circuit at 100% ED: 135 A electrical connection: 380 V space needed: 650 x 550 x 850 mm weight: 118 kg Pedpfod Hn Ufjx Aazegt

Condition: new, – Semi-automatic – Hydraulic – 2 speeds – Double miter – Hydraulically adjustable saw pressure – Cooling – Saw blade 2730 x 27 x 0.9 mm – Foot pedal control – Emergency stop Pgsdjh Razfopfx Aazjt – Documentation – 400 V

Condition: new, cutting diameter 355 mm dimensions of saw-band 3770 x 34 x 1,1 mm cutting speed 20 - 80 m/min cutting width 490 x 280 mm 290 mm Impact energy 250 mm 230 mm 180 mm connected load frequency 400 Volt total power requirement 2,2 kW weight of the machine ca. 0,7 t dimensions 1,43 x 0,72 x 1,7 m Pgedpfomhm Aqex Aazjt Semi-automatic miter band saw - Miter cuts up to 45° left + right - Miter cuts up to 60° right - Vice with quick release device - Tape tension control via manometer - Electr. automatic cooling

Condition: new, Year of construction: 2022, IN STOCK -- Semi-automatic metal bandsaw machine with high cutting precision! With this machine, miter cuts up to 45° on the left and up to 30° on the right are possible (swivel range 45° on the left and 60° on the right) Pgjdpfx Ajmf T Hpjazst Technical data: ● Cutting range: - 90° round: 280 mm / square: 240 mm / rectangular: 420 x 200 mm - 45° right round: 260 mm / square: 240 mm / rectangular: 260 x 200 mm - 30° right round: 170 mm / square: 160 mm / rectangular: 160 x 160 mm - 45° left round: 200 mm / square: 180 mm / rectangular: 250 x 100 mm ● Drive power: 0,9-1,5 kW / 400 V / 50 Hz ● Band saw speed: 35 / 70 m/min ● Saw blade dimensions: 3270 x 27 x 0,9 mm Basic equipment: ● Hydraulic control of the saw frame ● Automatic height limitation of the saw frame via contact sensors ● Easy and convenient clamping of the material via a hydraulic short-stroke cylinder ● Hydraulic cutting pressure regulation ● Simple, continuous adjustment of the saw for miter cuts ● Electrical blade tension monitoring with saw blade breakage control

Condition: new, Year of construction: 2026, The CORMAK HBS260 metal bandsaw for cutting pipes, profiles and bars is widely used in locksmith and metalworking workshops where precision, quality and cutting speed are essential. The model features a pivoting arm from 0° to 60°. The frame design ensures precise and quiet operation. It has a removable chip tray for easy cleaning! Machine characteristics The CORMAK HBS260 horizontal metal bandsaw with a pivoting arm enables cutting perpendicular to the material axis and at any angle within the range of 0° to 60°. The material can be fed manually or by any mechanical device, while the tool feed operates automatically. The blade guides are fitted with special carbide plates and bearings, which have a significant influence on the blade’s guidance, service life, straightness, accuracy and cutting quality. The carbide guidance system greatly reduces machine and blade wear. The machine is equipped with an efficient coolant pump with a closed coolant circulation system. The saw arm is made from a single cast-iron element, and with the use of a 27 mm wide cutting blade, it enables series cutting of both profiles and solid materials. The vice is mounted on an adjustable base and features a quick-clamping system. The blade guides are fitted with hard metal (carbide) plates and rolling bearing systems. These carbide guides are responsible for the cutting precision and straightness. The upper part of the base is shaped as a tray for draining coolant and collecting chips generated during the cutting process. The base is fitted with a cast-iron worktable with a pivoting arm and a control panel mounted on a separate arm. In the cutting process, the main cutting motion is the movement of the cutting blade, while the feed is achieved by lowering the arm. The arm lowering speed (cutting speed) is controlled by a hydraulic cylinder. The feed rate is regulated via the saw’s control panel. Two blade speeds are available: 35 and 70 m/min. When the arm reaches its lower position (after the cut), the drive to the cutting blade is automatically switched off. Safety is ensured by blade guards and micro-switches that stop the motor after the cutting cycle or when any guard is opened. Additional protection automatically switches off the bandsaw in the event of blade breakage. Blade size [mm] 2520 x 27 x 0.9 Blade tension mechanical (manual) Blade speeds [m/min] 35, 70 Arm lowering control stepless – hydraulic cylinder Vice base height [mm] 860 Saw wheel diameter [mm] 300 Saw frame swivel [°] 0–60 Pedpjudi Uzefx Aazsgt Power supply 3-phase 400V Main motor power [kW] 1.1 / 1.5 Coolant pump motor power [kW] 0.05 Dimensions with base [cm] 150 x 80 x 140 Weight [kg] gross/net – 210 / 180 kg Additionally 2 M42 saw blades 5L Emulsol ZW580 magnetic chip collector

Condition: new, cutting diameter 235 mm dimensions of saw-band 2645 x 27 x 0,9 mm cutting width 280 x 190 mm cutting speed 45/90 m/min 120 mm Pgodpfxsp Scqyj Aazjt 120 mm 190 mm Impact energy 170 mm connected load frequency 400 Volt total power requirement 1,1 kW weight of the machine ca. 290 Kg dimensions 1,2 x 0,8 x 1,2 m Double miter band saw -Miter cuts up to 60° left and 45° right -Vice with quick clamping device -Band tension control -Electr. Automatic cooling

Condition: new, Year of construction: 2026, functionality: fully functional, working height: 2,200 mm, BUMEX Sp. z o.o. offers a professional industrial washing system designed for the preparation of components prior to the powder coating process. The equipment has been engineered for demanding industrial environments where washing efficiency, process stability, and long-term durability are essential. The washing system enables effective preparation of steel and aluminum components through a multi-stage cleaning, degreasing and rinsing process. Technical parameters Working chamber dimensions: 1500 × 3200 × 2200 mm Process technology: 3-stage washing process Process tanks The unit is equipped with three process tanks: tank for cleaning / degreasing chemicals tank for rinsing water tank for demineralized water (DEMI water) Tank capacity: 1500 – 2000 liters DEMI water generator The system is equipped with a demineralized water generator, ensuring high-quality final rinsing and optimal surface preparation before powder coating. Heating system The chemical tank is equipped with a heating system for the process liquid. Available heating options: oil heating gas heating electric heating Maximum operating temperature: up to 60°C Machine construction Pgsdpfx Ashfv D Seazet The machine is manufactured entirely from high-quality stainless steel AISI 1.4301, which provides: excellent chemical resistance long service life easy maintenance and cleaning The washer features: very robust industrial construction full thermal insulation of the entire machine to reduce energy losses spray system designed for minimal mixing of process liquids pre-filter for collecting contaminants high washing efficiency Control system The machine is equipped with a fully automatic control system, enabling precise control of: process temperature pump operation washing time sequence of process stages Why choose BUMEX? Our equipment stands out on the market due to: very high manufacturing quality robust industrial construction operational safety complete technical documentation possibility of adapting the equipment to the existing production facility All machines manufactured by BUMEX Sp. z o.o. are CE certified. Additional technological support BUMEX also provides: powder coating booths dust extraction and filtration systems industrial ventilation systems professional technological consulting Cooperation conditions company transport available (price determined individually) VAT invoices issued short production lead times possibility of manufacturing machines in custom configurations and dimensions